This drawing shows the location(s) of the
warning decal(s). If a decal is missing or
illegible, see the front cover of this
manual and request a free replacement
decal. Apply the decal in the location
shown. Note: The decal(s) may not be
shown at actual size.
PROFORM is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING: T
instructions in this manual and all warnings on your exercise bike before using your exercise bike.
ICON assumes no responsibility for personal injury or property damage sustained by or through the
use of this product.
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or persons with pre-existing health problems.
2. Use the exercise bike only as described in
this manual.
3. It is the responsibility of the owner to ensure
that all users of the exercise bike are adequately informed of all precautions.
4. The exercise bike is intended for home use
only. Do not use the exercise bike in a commercial, rental, or institutional setting.
5. Keep the exercise bike indoors, away from
moisture and dust. Do not put the exercise
bike in a garage or covered patio, or near
water.
o reduce the risk of serious injury, read all important precautions and
9. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the exercise bike. Always wear
athletic shoes for foot protection.
10. The exercise bike should not be used by
persons weighing more than 250 lbs.
(113 kg).
11. The heart rate monitor is not a medical
device. Various factors, including the user's
movement, may affect the accuracy of heart
rate readings. The heart rate monitor is
intended only as an exercise aid in determining heart rate trends in general.
12. The exercise bike does not have a free
wheel; the pedals will continue to move until
the flywheel stops. Reduce your pedaling
speed in a controlled way.
6. Place the exercise bike on a level surface
with at least 2 ft. (0.6 m) of clearance around
the exercise bike. To protect the floor or
carpet from damage, place a mat under the
exercise bike.
7. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
8. Keep children under age 12 and pets away
from the exercise bike at all times.
13. Always keep your back straight while using
the exercise bike; do not arch your back.
14. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
3
BEFORE YOU BEGIN
Thank you for selecting the new PROFORM®210 CSX
exercise bike. Cycling is an effective exercise for
increasing cardiovascular fitness, building endurance,
nd toning the body. The 210 CSX exercise bike pro-
a
vides an impressive selection of features designed to
ake your workouts at home more effective and
m
enjoyable.
For your benefit, read this manual carefully before
you use the exercise bike. If you have questions
Length: 4 ft. 8 in. (142 cm)
Width: 2 ft. (61 cm)
Accessory Tray
after reading this manual, please see the front cover
of this manual. To help us assist you, note the product
model number and serial number before contacting
s. The model number and the location of the serial
u
number decal are shown on the front cover of this
anual.
m
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Console
Handlebar
Water Bottle Holder*
Backrest
Seat
Wheel
Pedal/Strap
Leveling Foot
Heart Rate Monitor
Adjustment Knob
Seat Handlebar
*Water bottle is not included
4
ASSEMBLY
M10 Locknut
(77)–2
M8 Locknut
(37)–6
M8 Split
Washer (36)–4
M6 Washer
(70)–8
M8 x 65mm Button
Bolt (71)–2
M4 x 22mm
Screw (69)–2
M4 x 16mm
Screw (73)–6
M8 x 16mm
Screw (35)–4
M10 x 75mm
Bolt (67)–4
M8 x 38mm Button
Bolt (53)–4
M6 x 25mm
Screw (72)–2
M6 x 40mm
Screw (40)–8
To hire an authorized service technician to assemble the exercise bike, call 1-800-445-2480.
ssembly requires two persons. Place all parts of the exercise bike in a cleared area and remove the packing
A
materials. Do not dispose of the packing materials until assembly is completed.
In addition to the included tool(s), assembly requires a Phillips screwdriverand an
adjustable wrench.
Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following
the key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if
it has been preassembled. To avoid damaging parts, do not use power tools for assembly.
5
1.
To make assembly easier, read the
nformation on page 5 before you begin.
i
dentify the Front Stabilizer (14), which has a
I
Leveling Foot (57) near each end.
While a second person lifts the Front Frame (1),
attach the Front Stabilizer (14) to the Front
Frame with two M10 x 75mm Bolts (67).
1
14
1
57
57
67
2. Loosen the Adjustment Knob (11), slide the
Rear Frame (43) out of the Front Frame (1),
and then retighten the Adjustment Knob.
Note: After the exercise bike is assembled, see
HOW TO ADJUST THE SEAT FRAME on page
11 and adjust the Seat (not shown) to the proper position.
Attach the Rear Stabilizer (2) to the Rear Frame
(43) with two M10 x 75mm Bolts (67) and two
M10 Locknuts (63).
3. Tip: Avoid pinching the wires. Attach the Seat
Frame (5) to the Seat Handlebar (44) with two
M8 x 65mm Button Bolts (68) and two M8
Locknuts (37).
2
11
63
2
43
63
67
3
5
68
Avoid pinching
the wires
1
44
37
6
4. Have a second person hold the Seat Handlebar
(44) near the top of the Rear Frame (43) until
step 5 is completed.
4
43
Connect the Heart Rate Wire (45) to the Lower
ulse Wire (56).
P
Insert the Lower Pulse Wire (56) and the Heart
Rate Wire (45) into the Rear Frame (43). Then,
press the grommet (A) into the hole in the Rear
Frame.
5. Tip: Avoid pinching the wires. Attach the Seat
Frame (5) to the Rear Frame (43) with two M6 x
25mm Screws (66).
56
5
4
A
44
5
5
43
66
6. Attach the Backrest (58) to the Seat Frame (5)
with four M6 x 40mm Screws (40) and four M6
Washers (70).
66
Avoid pinching
the wires
6
58
5
70
40
40
70
7
7. Attach the Seat (12) to the Rear Frame (43)
with four M6 x 40mm Screws (40) and four M6
Washers (70).
7
12
43
70
70
40
40
8. Orient the Upright (3) and the Top Shield (9) as
shown. Slide the Top Shield upward onto the
Upright.
Have a second person hold the Upright (3) and
the Top Shield (9) near the Front Frame (1).
Connect the Upper Wire (32) to the Lower Wire
(31). Then, connect the Upper Pulse Wire (55)
to the Lower Pulse Wire (56).
Insert the wires downward into the Front Frame
(1).
Tip: To prevent the wires from falling into
the Upright (3), secure the wires with a rubber band or tape.
9. Tip: Avoid pinching the wires. Slide the
Upright (3) onto the Front Frame (1).
Attach the Upright (3) with four M8 x 16mm
Screws (35) and four M8 Split Washers (36).
Press the Top Shield (9) downward into the Left
and Right Shields (17, 18).
8
3
9
32
31
9
3
35
9
36
55
56
1
Avoid pinching
36
35
36
1
the wires
35
17
18
36
35
8
Loading...
+ 16 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.