ProForm PFEL078072 User Manual
Model No. PFEL07807.2
Serial No.
Write the serial number in the
space above for reference.
Serial
Number
Decal
QUESTIONS?
If you have questions, or if parts are
damaged or missing, DO NOT
CONTACT THE STORE; please
contact Customer Care.
IMPORTANT: Please register this
product (see the limited warranty
on the back cover of this manual)
before contacting Customer Care.
USERʼS MANUAL
CALL TOLL-FREE:
1-888-533-1333
Mon.–Fri., 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
www.proformservice.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
MPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
I
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
HOW TO USE THE ELLIPTICAL EXERCISER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
The warning decal shown here has been applied
in the location shown. If the decal is missing
or illegible, see the front cover of this manual
and request a free replacement decal. Apply
the decal in the location shown. Note: The
decal may not be shown at actual size.
PROFORM is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING: T
instructions in this manual and all warnings on your elliptical exerciser before using your elliptical
exerciser. ICON assumes no responsibility for personal injury or property damage sustained by or
through the use of this product.
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or persons with pre-existing health problems.
2. Use the elliptical exerciser only as described
in this manual.
3. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
4. The elliptical exerciser is intended for
home use only. Do not use the elliptical exerciser in a commercial, rental, or institutional
setting.
5. Keep the elliptical exerciser indoors, away
from moisture and dust. Place the elliptical
exerciser on a level surface, with a mat
beneath it to protect the floor or carpet.
Make sure that there is at least 3 ft. (0.9 m) of
clearance in the front and rear of your elliptical exerciser and 2 ft. (0.6 m) on each side.
6. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
7. Keep children under age 12 and pets away
from the elliptical exerciser at all times.
o reduce the risk of serious injury, read all important precautions and
8. The elliptical exerciser should not be used
by persons weighing more than 350 lbs.
(159 kg).
9. Wear appropriate exercise clothes while
using the elliptical exerciser. Always wear
athletic shoes for foot protection while exercising.
10. Hold the handlebars or the upper body arms
when mounting, dismounting, or using the
elliptical exerciser.
11. The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determining heart rate trends in general.
12. Keep your back straight while using the
elliptical exerciser; do not arch your back.
13. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
14. When you stop exercising, allow the pedals
to slowly come to a stop.
3
BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM
PIC 1200 PRO elliptical exerciser. The EPIC 1200
E
PRO elliptical exerciser provides an impressive selection of features designed to make your workouts at
home more effective and enjoyable.
®
cover of this manual. To help us assist you, note the
roduct model number and serial number before con-
p
tacting us. The model number and the location of the
serial number decal are shown on the front cover of
this manual.
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
tions after reading this manual, please see the front
Upper Body Arm
Pulse Sensor
Water Bottle Holder*
Ramp
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Fan
Console
Pedal Disc
Handle
Leveling Foot
Wheel
Pedal
*No water bottle is included
4
#8 x 3/4"
Screw (78)–4
5/16" x 1" Patch
Screw (81)–11
#10 x 1/2"
Screw (79)–10
5/16" x 1 1/2" Button
Bolt (73)–4
5/16" Washer
(104)–6
#10 Fender
Washer (80)–10
5/8" Wave
Washer (102)–6
5/16" Split
Washer (105)–5
5/16" Locknut
(106)–4
M10 x 20mm Patch
Screw (108)–6
Pivot Spacer
(71)–4
5/16" x 2 1/2" Button
Screw (88)–8
M10 Split
Washer (110)–6
M6 Split
Washer
(111)–10
ASSEMBLY
To hire an authorized service technician to assemble the elliptical exerciser, call 1-800-445-2480.
ssembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
A
packing materials. Do not dispose of the packing materials until assembly is completed.
Assembly requires the included tool(s) and your own Phillips screwdriver ,
adjustable wrench , and rubber mallet .
As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parentheses
below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number
following the parentheses is the quantity needed for assembly. Note: If a part is not in the hardware kit, check
to see if it has been preassembled.
5
1.
To make assembly easier, read the
nformation on page 5 before you begin.
i
ith the help of another person, place two
W
packing inserts from the packing material under
the rear of the Frame (1) so that the Frame is
lifted off the floor. Have the other person hold
the elliptical exerciser to prevent it from
moving from side to side until this step is
completed.
Attach the Rear Stabilizer (3) to the Frame (1)
with four 5/16" x 2 1/2" Button Screws (88).
Then, remove the packing inserts and lower the
Rear Stabilizer.
1
1
Packing
Inserts
88
3
88
2. With the help of another person, place two packing inserts under the front of the Frame (1) so
that the Frame is lifted off the floor. Have the
other person hold the elliptical exerciser to
prevent it from moving from side to side
until this step is completed.
Attach the Front Stabilizer (2) to the Frame (1)
with four 5/16" x 2 1/2" Button Screws (88).
Then, remove the packing inserts and lower the
Front Stabilizer.
2
1
2
Packing
Inserts
88
88
6
3. Tip: Be careful not to pinch the Wire
Harnesses (97, 54) during this step. Start all
screws before tightening any of them.
While a second person holds the Upright (6)
ear the Frame (1), connect the Upper Wire
n
Harness (97) to the Lower Wire Harness (54).
Attach the Upright (6) to the Frame (1) with five
5/16" x 1" Patch Screws (81) and five 5/16"
Split Washers (105).
3
Avoid pinching the
Wire Harnesses (97,
54) during this step
6
97
4. Apply a generous amount of the included
grease to the Pivot Axle (33) and to two 5/8"
Wave Washers (102).
Tip: Avoid pinching or damaging the Upper
Wire Harness (97). Insert the Pivot Axle (33)
through the Upright (6). Then, slide a 5/8" Wave
Washer (102) onto each end of the Pivot Axle.
Slide an Upper Body Leg (12) onto the left side
of the Pivot Axle (33). Attach the Upper Body
Leg with a 5/16" x 1" Patch Screw (81), a Large
Axle Cover (94), and a 5/16" Washer (104).
4
81
94
Grease
102
81
105
81
104
12
97
54
1
105
81
Grease
104
6
33
102
94
81
12
Attach the other Upper Body Leg (12) in the
same way.
7
5. Identify the Right Pedal Plate (107), which is
marked with an “R” sticker. Attach the Right
Pedal Plate to the Right Pedal Arm (8) with
hree M10 x 20mm Patch Screws (108) and
t
three M10 Split Washers (110).
Identify the Right Pedal Assembly (62), which is
located in a package marked with a “Right”
sticker. Attach the Right Pedal Assembly to the
Right Pedal Plate (107) with five #10 x 1/2"
Screws (79), five M6 Split Washers (111), and
five #10 Fender Washers (80). Tip: To avoid
damaging the Pedal, do not overtighten the
Screws.
Repeat this step for the Left Pedal Plate (not
shown) and the Left Pedal Assembly (56).
5
62
08
1
110
07
1
56
80
8
111
79
79
6. Identify the Right Link Arm (10), which is
marked with a “Right” sticker. Apply a small
amount of grease to the axles on the Right Link
Arm and to two 5/8" Wave Washers (102).
Then, slide a Pivot Spacer (71) and a Wave
Washer onto each axle.
At the same time, slide the Right Link Arm (10)
into the right Upper Body Leg (12) and into the
Right Pedal Arm (8).
Attach the Right Link Arm (10) to the right
Upper Body Leg (12) with a 5/16" x 1" Patch
Screw (81), a Large Axle Cover (94), and a
5/16" Washer (104).
Then, attach the Right Link Arm (10) to the
Right Pedal Arm (8) with a 5/16" x 1" Patch
Screw (81), a Small Axle Cover (67), and a
5/16" Washer (104).
Tip: If you have a hard time working the
Right Link Arm (10) all the way into the right
Upper Body Leg (12) and the Right Pedal
Arm (8), try working it in halfway and then
tightening the 5/16" x 1" Patch Screws (81)
to pull it the rest of the way in.
6
12
81
67
104
104
81
94
71
102
8
Grease
Grease
102
71
10
Repeat this step on the other side of the
elliptical exerciser.
8
7. While a second person holds the Console (60)
near the Upright (6), connect the console wire
to the Upper Wire Harness (97). Then, connect
he console pulse wire to the Hand Pulse Wire
t
(65). Insert the excess wire downward into the
pright.
U
Tip: Avoid pinching the wires during this
step. Attach the Console (60) to the Upright (6)
with four #8 x 3/4" Screws (78).
7
C
60
onsole Wire
97
Avoid pinching the
wires during this step
Pulse Wire
5
6
6
78
8. Identify the Right Upper Body Arm (31), which is
marked with a “Right” sticker and orient it as
shown. Attach the Right Upper Body Arm to the
right Upper Body Leg (12) with two 5/16" x 1
1/2" Button Bolts (73) and two 5/16" Locknuts
(106). Make sure that the Locknuts are in the
hexagonal holes.
Repeat this step to attach the Left Upper
Body Arm (7) to the left Upper Body Leg
(12).
9. Plug the Power Cord (55) into the power socket
at the rear of the elliptical exerciser. IMPOR-
TANT: If the elliptical exerciser has been
exposed to cold temperatures, allow it to
warm to room temperature before plugging
in the power cord. If you do not do this, the
console displays or other electronic components may become damaged.
8
7
73
12
9
31
106
Hexagonal
Holes
12
Note: When you plug in the elliptical exerciser for the first time (see HOW TO PLUG IN
THE POWER CORD on page 10), the Ramp
(not shown) will calibrate automatically. The
Ramp will move upward and downward as it
calibrates. When the Ramp stops moving, the
Ramp is calibrated.
IMPORTANT: If the Ramp (not shown) does
not calibrate automatically, see HOW TO
CALIBRATE THE RAMP on page 20 and
manually calibrate the Ramp.
10. Make sure that all parts of the elliptical exerciser are properly tightened. Note: Some hardware may be
left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the
elliptical exerciser.
55
9
Loading...