ProForm PFEL039150 User Manual

www.proform.com

Model No. PFEL03915.0
Serial No.

Write the serial number in the
space above for reference.

Serial

Number

Decal

ACTIVATE YOUR
WARRANTY

To register your product and
activate your warranty today,
go to www.proformservice.com/
registration.

CUSTOMER CARE

USER’S MANUAL

For service at any time, go to
www.proformservice.com.

Or call 1-888-533-1333
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–12 p.m. MT

Please do not contact the store.

CAUTION

Read all precautions and instruc­tions in this manual before using
this equipment. Keep this manual
for future reference.

TABLE OF CONTENTS

WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

HOW TO USE THE ELLIPTICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

LIMITED WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

WARNING DECAL PLACEMENT

This drawing shows the location(s) of the warning decal(s).

If a decal is missing or illegible, see the front cover
of this manual and request a free replacement decal.
Apply the decal in the location shown. Note: The

decal(s) may not be shown at actual size.

PROFORM is a registered trademark of ICON Health & Fitness, Inc.

2

IMPORTANT PRECAUTIONS

WARNING: To reduce the risk of serious injury, read all important precautions and

instructions in this manual and all warnings on your elliptical before using your elliptical. ICON
assumes no responsibility for personal injury or property damage sustained by or through the
use of this product.

1. It is the responsibility of the owner to ensure
that all users of the elliptical are adequately
informed of all precautions.

2. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or per­sons with pre-existing health problems.

3. Use the elliptical only as described in this
manual.

4. The elliptical is intended for home use only.
Do not use the elliptical in a commercial,
rental, or institutional setting.

5. Keep the elliptical indoors, away from mois­ture and dust. Do not put the elliptical in a
garage or covered patio, or near water.

6. Place the elliptical on a level surface, with at
least 3 ft. (0.9 m) of clearance in the front and
rear of the elliptical and 2 ft. (0.6 m) on each
side. To protect the floor or carpet from dam­age, place a mat under the elliptical.

9. The elliptical should not be used by persons
weighing more than 250 lbs. (113 kg).

10. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the elliptical. Always wear athletic
shoes for foot protection while exercising.

11. Hold the handlebars or the upper body arms
when mounting, dismounting, or using the
elliptical.

12. The heart rate monitor is not a medical
device. Various factors may affect the accu­racy of heart rate readings. The heart rate
monitor is intended only as an exercise aid
in determining heart rate trends in general.

13. The elliptical does not have a freewheel; the
pedals will continue to move until the fly­wheel stops. Reduce your pedaling speed in
a controlled way.

14. Keep your back straight while using the ellip­tical; do not arch your back.

7. Inspect and properly tighten all parts regu­larly. Replace any worn parts immediately.

8. Keep children under age 12 and pets away
from the elliptical at all times.

15. Over exercising may result in serious injury
or death. If you feel faint, if you become short
of breath, or if you experience pain while
exercising, stop immediately and cool down.

3

STANDARD SERVICE PLANS

all

4

BEFORE YOU BEGIN

Thank you for purchasing the PROFORM® 650 LE
elliptical. The 650 LE elliptical provides an array of fea­tures designed to make your workouts at home more
effective and enjoyable.

For your benefit, read this manual carefully before
you use the elliptical. If you have questions after

reading this manual, please see the front cover of this

Length: 5 ft. 4 in. (163 cm)
Width: 2 ft. 3 in. (69 cm)

Console

Handlebar

manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.

Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.

Upper Body Arm

Heart Rate Monitor

Fan

Storage Magnet

Pedal

Crank Arm

Handle

Leveling Foot

Water Bottle Holder*

Wheel

Pedal Arm Latch

Storage Latch

*Water bottle is not included

5

PART IDENTIFICATION CHART

Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the
key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it

has been preassembled. Extra parts may be included.

M4 Split

Washer
(112)–8

M4 x 16mm

Blunt Screw

(104)–8

M8 x 23mm Shoulder

Screw (115)–4

M4
Washer
(102)–8

M8 x 69mm Bolt (80)–1

M8 Split

Washer

(90)–3

M4 x 16mm

Round Head

Screw (101)–10

M8 x 23mm

Screw (84)–4

Wave Washer

(111)–2

M4 x 32mm

Round Head

Screw (105)–6

M8 Washer

(88)–6

Hub Screw

(87)–8

M8 Jam Nut

(79)–7

M4 x 50mm Screw

(108)–2

M8 x 41mm

Bolt (78)–4

M8 x 80mm Bolt (116)–2

M10 Locknut

(81)–2

M10 x 80mm Carriage Bolt

(82)–2

M10 x 127mm Screw (83)–2

6

ASSEMBLY

• To hire an authorized service technician to
assemble this product, call 1-800-445-2480.

• Assembly requires two persons.

• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you fi nish all assembly steps.

• Left parts are marked “L” or “Left” and right parts
are marked “R” or “Right.”

• To identify small parts, see page 6.

1. Go to www.proformservice.com/registration

on your computer and register your product.

• activates your warranty

• saves you time if you ever need to contact
Customer Care

• allows us to notify you of upgrades and offers

• In addition to the included tool(s), assembly
requires the following tools:

one Phillips screwdriver

one adjustable wrench

one rubber mallet

Assembly may be easier if you have a set of
wrenches. To avoid damaging parts, do not use
power tools.

1

Note: If you do not have Internet access, call

Customer Care (see the front cover of this
manual) and register your product.

2. While a second person lifts the Base (1), attach
the Front Stabilizer (6) to the Base with two
M10 x 80mm Carriage Bolts (82) and two M10
Locknuts (81).

2

82

6

81

81

1

7

3. Remove and discard the indicated screw and the
shipping bracket

Next, tighten the Base Foot (26) into the

Base (1).

3

1

Shipping

26

Screw

Bracket

4. Orient the Rear Stabilizer (7) as indicated by the
sticker. Attach the Rear Stabilizer to the Frame
(2) with two M10 x 127mm Screws (83).

Next, hold the handle on the Frame (2), press

the Latch (68), and lower the Frame until the
Rear Stabilizer (7) rests on the floor.

4

Handle

83

7

2

68

8

5. Hold a Hub Cover (75) and a Crank Arm (36)
against the Crank (45).

Align the holes in the Hub Cover (75) and the

Crank Arm (36) with the unused holes in the left
side of the Crank (45).

Insert four Hub Screws (87) into the Hub Cover

(75) and the Crank Arm (36), and finger tighten
the Hub Screws into the Crank (45). Tighten

one Hub Screw, and then tighten the Hub
Screw across from the first Hub Screw. Then,
tighten the remaining two Hub Screws.

Repeat this step on the right side of the

elliptical.

Make sure that the Crank Arms (36) are ori-

ented with the Crank Bushing Sleeves (43) in
the positions shown. Note: There are no Pulley

Screws (98) on the right side.

5

43

98

45

36

75

87

87

43

36

6. While a second person holds the Upright (3)
near the Base (1), connect the Upper Wire
Harness (48) to the Lower Wire Harness (49).

Tip: Avoid pinching the wires. Insert the

Upright (3) into the Base (1).

Attach the Upright (3) with an M8 x 69mm Bolt

(80), an M8 Split Washer (90), and an M8 Jam
Nut (79). Do not tighten the Bolt yet; make

sure that the Jam Nut is in the hexagonal
hole in the Base.

Next, finger tighten two M8 x 23mm Screws (84)

and two M8 Split Washers (90) into the Base (1).
Do not tighten the Screws yet.

Attach the Water Bottle Holder (22) to the Base

(1) with two M4 x 16mm Blunt Screws (104).

6

Avoid pinching

the wires

3

48

80

90

90

84

49

1

79

22

90

84

104

9

7. Identify the Left Upright Cover (17) and hold it
against the left side of the Upright (3).

Attach the Left Upright Cover (17) with two M4 x

16mm Round Head Screws (101).

Attach the Right Upright Cover (39) in the

same way.

7

3

39

101

17

101

8. Identify the Left and Right Handlebars (119, 120)
and orient them as shown.

Tip: Avoid pinching the Pulse Wires (118).

Attach the Left and Right Handlebars (119, 120)
to the Upright (3) with two M8 x 80mm Bolts
(116) and two M8 Jam Nuts (79).

8

119

79

118

Avoid pinching

the wires

116

3

120

116

118

10