Page 1
USER'S MANUAL
¨
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Serial
Number
Decal
Model No. PETL61591
Serial No.
Find the serial number in the location
shown below. Write the serial number
in the space above for reference.
Part No. 163278 R1000A Printed in USA © 2000 ICON Health & Fitness, Inc.
Visit our website at
www.proform.com
new products, prizes,
fitness tips, and much more!
Patent Pending
QUESTIONS?
As a manufacturer, we are
committed to providing
complete customer satisfaction.
If you have questions, or if
there are missing parts, we will
guarantee complete satisfaction
through our Customer Service
Department.
Please CALL:
Or WRITE:
ICON Fitness Lifestyle Ltd.
Greenwich House
223 North Street
Sheepscar
Leeds LS7 2AA
West Yorkshire
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, contact the ICON Health & Fitness Ltd. office, or write:
ICON Health & Fitness Ltd.
Greenwich House
223 North Street
Sheepscar
Leeds LS7 2AA
West Yorkshire
Tel: Country Code: 0345-089009
Fax: 0113-2411120
When ordering parts, please be prepared to give the following information:
¥ The MODEL NUMBER OF THE PRODUCT (PETL61591)
¥ The NAME OF THE PRODUCT (PROFORM¨615 treadmill)
¥ The SERIAL NUMBER OF THE PRODUCT (see the front cover of this manual)
¥ The KEY NUMBER OF THE PART(S) (see the PART LIST on page 23 and the EXPLODED DRAWING attached
in the centre of this manual)
¥ The DESCRIPTION OF THE PART(S) (see the PART LIST on page 23 and the EXPLODED DRAWING attached
in the centre of this manual).
PROFORM¨is a registered trademark of ICON Health & Fitness, Inc.
0345-089009
Page 2
PART LISTÑModel No. PETL61591 R1000A
1 1 Motor Belt
2 1 Pulley/Flywheel/Fan
3 4 Motor Nut
4* 1 Motor/Pulley/
Flywheel/ Fan
5 1 Incline Motor Bolt
6 1 Plastic Incline Motor
Spacer
7 1 Incline Motor
8 1 Stop Bracket
9 1 Small Nut
10 2 Star Washer
11 1 Optic Switch
12 1 Frame
13 1 Optic Switch Bolt
14 1 Incline Optic Disk
15 8 Incline Motor Nut
16 2 Hood Screw
17 4 Plastic Stand-off
18 2 Hood Bracket (Short)
19 1 Hood Bracket (Long)
20 2 Warning Decal
21 1 Reed Switch
22 1 Reed Switch Clip
23 1 Motor/Controller Wire
24 1 Controller
25 1 Electronics Bracket
26 1 Circuit Breaker
27 1 Receptacle
28 1 Extension Leg Assm.
29 1 On/Off Switch
30 1 Inlet Bracket
31 1 Incline Leg
32 2 Frame Pivot Bolt
33 2 Frame Pivot Spacer
34 1 Upright Wire Harness
35 1 Front Roller Adj. Bolt
36 3 Roller Adj. Washer
37 2 Motor Tension Nut/
Front Roller Nut
38 4 Motor Bolt
39 2 Cap Screw
40 1 Left Foot Rail Cap
41 2 Foot Rail
42 1 Front Roller/Pulley
43 1 Magnet
44 2 Platform Screw (Mid)
45 2 Isolator
46 4 Isolator Screw
47 15 Plastic Fastener
48 1 Shield
49 2 Belt Guide
50 1 Book Holder
51 1 Front Belly Pan
52 1 Power Supply
53 4 Cable Tie Clamp
54 4 Cable Tie
55 1 Walking Belt
56 1 24Ó Wire Harness
57 1 Rear Roller
58 1 Belly Pan Spacer
59 2 Rear Foot
60 1 Rear Foot Screw
61 1 Ground Wire
62 13 Ground Wire Screw
63 1 Belly Pan
64 1 Rear Endcap
65 2 Rear Roller Adj. Bolt
66 1 Motor
67 1 Latch Decal
68 4 Platform Screw
69 3 Electronics Screw
70 1 Latch Catch
71 1 Walking Platform
72 5 8Ó Cable Tie
73 1 Jack
74 1 Motor Tension Bolt
75 2 Foot Rail Insert
76 14 Screw
77 1 Console
78 1 Motor Isolator Plate
79 4 Long Screw
80 1 10Õ I-Fit Wire
81 4 Motor Star Bushing
82 1 Upright
83 2 Incline Leg Pivot Bolt
84 2 Side Hood Screw
85 2 Handrail Extension
86 2 Wheel Bolt
87 1 Console Base
88 1 Motor Tension Washer
89 10 Console/Catch Screw
90 1 Key/Clip
91 1 Incline Motor Plate
92 1 Right Foot Rail Cap
93 1 Motor Tension Spacer
94 1 Motor Hood
95 2 Front Wheel
96 1 Incline Motor Shield
97 4 Thick Base Pad
98 1 12Ó Audio Wire
99 1 Upright Grommet
100 1 Allen Wrench
101 11 Short Screw
102 1 Lock Knob
103 2 Extension Leg
104 2 Extension Leg Cap
105 1 Shock
106 1 Choke
107 2 Pulse Bar Bolt
108 2 Pulse Bar Washer
109 1 Pulse Bar
110 2 Handrail Foam Grip
111 1 Lock Knob Sleeve
112 1 Spring
113 1 Lock Pin Collar
114 1 Pin Clip
115 1 Lock Pin
116 1 Console Base Bottom
117 2 Upright Endcap
118 1 Motor Sleeve
119 8 Hood Bracket Screw/
Incline Shield Screw
120 1 Rear Foot Spacer
121** 1 Hand Weight Set
122 1 Long Incline Motor Bolt
123 2 Static Warning
124 1 Hand Pulse Wire
125 1 Motor/Choke Bracket
126 1 Filter
127 1 UK Power Cord
128 1 Euro Power Cord
129** 1 Chest Pulse Sensor
130** 1 Chest Pulse Sensor
Strap
# 1 15Ó Wire Harness
# 1 8Ó White Wire, 2F
# 1 14Ó White Wire, 2F
# 1 8Ó Black M/F
# 1 8Ó Blue Wire, 2F
# 1 4Ó Blue Wire, 2F
# 1 4Ó Black Wire, 2F
# 1 6Ó Green Wire, F/Ring
# 1 8Ó Green Wire, F/Ring
# 1 8Ó Green Wire, 2 Ring
# 1 14Ó Blue 2F
# 1 25Ó Wire Harness
# 1 User's Manual
* Includes all parts shown in the
box
**For more information about the op-
tional hand weight set, see page
18
# These parts are not illustrated
Key
No. Qty. Description
Key
No. Qty. Description
Key
No. Qty. Description
To locate the parts listed below, refer to the EXPLODED DRAWING attached in the centre of this manual.
2
23
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
TROUBLE-SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING is attached in the centre of this manual.
¨
IMPORTANT PRECAUTIONS
WARNING:To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
2. Use the treadmill only as described in this
manual.
3. Place the treadmill on a level surface, with
2 m (eight feet) of clearance behind it. Do not
place the treadmill on any surface that blocks
air openings. To protect the floor or carpet
from damage, place a mat under the treadmill.
4. When choosing a location for the treadmill,
make sure that the location and position permit access to a plug.
5. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Keep children under the age of 12 and pets
away from the treadmill at all times.
8. The treadmill should not be used by persons
weighing more than 115 kg (250 pounds).
9. Never allow more than one person on the
treadmill at a time.
10. Wear appropriate exercise clothing when
using the treadmill. Do not wear loose clothing that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
Page 3
22
3
CONDITIONING GUIDELINES
The following guidelines will help you to plan your exercise program. RememberÑthese are general guidelines only. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your Òtraining zone.Ó The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
To measure your heart rate during exercise, use the
pulse sensor. If your heart rate is too high or too low,
adjust the speed and incline of the treadmill.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the treadmill until your heart rate is near the lowest number in
your training zone.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be Òaerobic.Ó Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-upÑStart each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparation for exercise.
Training Zone ExerciseÑAfter warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exerciseÑnever
hold your breath.
A Cool-downÑFinish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-exercise problems.
Exercise Frequency
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired.
The key to success is to make exercise a regular and
enjoyable part of your everyday life.
WARNING:Before beginning this
or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
11. When connecting the power cord (see page
8), plug the power cord into an earthed circuit. When replacing the fuse, an ASTA approved BS1362 type should be fitted to the
fuse carrier. A 13 amp fuse should be used.
No other appliance should be on the same circuit.
12. If an extension cord is needed, use only a 3conductor, 1mm2(14 gauge) cord that is no
longer than 1.5 meters (5 feet).
13. Keep the power cord away from heated surfaces.
14. Never move the walking belt whilst the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See BEFORE YOU BEGIN on page 5 if the treadmill is
not working properly.)
15. Never start the treadmill whilst you are standing on the walking belt. Always hold the
handrails whilst using the treadmill.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
17. The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is intended only as an exercise aid in determining
heart rate trends in general.
18. Never leave the treadmill unattended whilst it
is running. Always remove the key, unplug
the power cord and move the on/off switch to
the off position when the treadmill is not in
use. (See the drawing on page 5 for the location of the on/off switch.)
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO MOVE
THE TREADMILL on page 19.) You must be
able to safely lift 20 kg (45 pounds) in order to
raise, lower, or move the treadmill.
20. Do not change the incline of the treadmill by
placing objects under the treadmill.
21. When folding or moving the treadmill, make
sure that the latch pin is fully inserted into the
catch (see page 19).
22. Inspect and tighten all parts of the treadmill
regularly.
23. When using i-Fit.com CDÕs and videos, an
electronic ÒchirpingÓ sound will alert you
when the speed and/or incline of the treadmill
is about to change. Always listen for the
ÒchirpÓ and be prepared for speed and/or incline changes. In some instances, the speed
and/or incline may change before the personal trainer describes the change.
24. When using i-Fit.com CDÕs and videos, you
can manually override the speed and incline
settings at any time by pressing the speed
and incline buttons. However, when the next
ÒchirpÓ is heard, the speed and/or incline will
change to the next settings of the CD or video
program.
25. Always remove i-Fit.com CDÕs and videos
from your CD player or VCR when you are not
using them.
26. Never drop or insert any object into any
opening.
27. DANGER: Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the maintenance and adjustment procedures described in this manual. Never remove the
motor hood unless instructed to do so by an
authorised service representative. Servicing
other than the procedures in this manual
should be performed by an authorised service
representative only.
28. The treadmill is intended for in-home use
only. Do not use the treadmill in a commercial, rental, or institutional setting.
WARNING:Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
Page 4
214
PROBLEM: The walking belt slows when walked on
SOLUTION: a. If an extension cord is needed, use only a 3-conductor, 14-gauge (1mm2) cord that is no longer
than 1.5 meters (5 feet).
b. If the walking belt is overtightened, treadmill perfor-
mance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller adjustment bolts counterclockwise, 1/4 of a
turn. When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 5 to
7 cm off the walking platform. Be careful to keep the
walking belt centred. Plug in the power cord, insert
the key and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
c. If the walking belt still slows when walked on, please call our Customer Service Department.
PROBLEM: The walking belt is off-centre
SOLUTION: a. If the walking belt has shifted to the left, first remove
the key and UNPLUG THE POWER CORD. Using the
allen wrench, turn the left rear roller adjustment bolt
clockwise, and the right bolt counterclockwise, 1/4 of a
turn each. Be careful not to overtighten the walking belt.
Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is
centred.
b. If the walking belt has shifted to the right, first re-
move the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn the left rear roller adjustment bolt counterclockwise, and the right bolt clockwise,
1/4 of a turn each. Be careful not to overtighten the
walking belt. Plug in the power cord, insert the key and
run the treadmill for a few minutes. Repeat until the
walking belt is centred.
PROBLEM: The walking belt slips when walked on
SOLUTION: a. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using the
allen wrench, turn both rear roller adjustment bolts
clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each side of
the walking belt 5 to 7 inches off the walking platform.
Be careful to keep the walking belt centred. Plug in the
power cord, insert the key and carefully walk on the
treadmill for a few minutes. Repeat until the walking belt
is properly tightened.
PROBLEM: The incline of the treadmill does not change correctly or does not change when i-Fit.com
CDÕs and videos are played
SOLUTION: a. With the key inserted in the console, press one of the INCLINE buttons. While the incline is
changing, remove the key. After a few seconds, re-insert the key. The treadmill will automati-
cally rise to the maximum incline level and then return to the minimum level. This will recalibrate
the incline.
Rear Roller Adjustment Bolts
5Ð7 cm
b
b
a
a
Note: This decal is shown at 38% of actual size.
Note: This decal is shown at 20% of actual size.
The decals shown below have been placed on your treadmill. If a decal is missing or illegible, please call
our Customer Service Department to order a free replacement decal (see the front cover of this manual).
Apply the decal in the location shown.
Page 5
20
5
Thank you for selecting the revolutionary PROFORM
¨
615 treadmill. The PROFORM¨615 combines advanced technology with innovative design to help you
get the most from your exercise program in the convenience and privacy of your home. And when youÕre not
exercising, the unique treadmill can be folded up, requiring less than half the floor space of other treadmills.
For your benefit, read this manual carefully before
using the PROFORM¨615 treadmill. If you have ad-
ditional questions, please call our our Customer
Service Department at 0345-089009. To help us assist
you, please note the product model number and serial
number before calling. The model number of the treadmill is PETL61591. The serial number can be found on
a decal attached to the treadmill (see the front cover of
this manual for the location).
Before reading further, please review the drawing
below and familiarise yourself with the parts that are
labeled.
BEFORE YOU BEGIN
Handrail
Console
Latch Knob
Latch Pin
Pulse Sensor
Book Holder
Key/Clip
Circuit
Breaker
On/Off Switch
Walking Belt
Cushioned Walking Platform
Foot Rail
Rear Roller
Adjustment Bolts
Water Bottle
Holder (Bottle
not included)
RIGHT SIDE
LEFT SIDE
TROUBLE-SHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See HOW TO PLUG IN
THE POWER CORD on page 8.) If an extension cord is needed, use only a 3-conductor, 14gauge (1mm2) cord that is no longer than 1.5 meters (5 feet). Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the con-
sole. See step 1 on page 10.
c. Check the circuit breaker located on the treadmill
near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
d. Check the on/off switch located on the treadmill
near the power cord. The switch must be in the on
position.
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the
circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console. See step 1 on page 10.
d. Make sure that the on/off switch is in the on position.
e. If the treadmill still will not run, please call our Customer Service Department.
PROBLEM: The speed display on the console does not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. Remove the screws from the hood
and carefully remove the hood. Locate the Reed
Switch (21) and the Magnet (43) on the left side of the
Pulley (42). Turn the Pulley until the Magnet is aligned
with the Reed Switch. Make sure that the gap be-
tween the Magnet and the Reed Switch is about
3mm. If necessary, loosen the Screw (76) and move
the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes
to check for a correct speed reading.
Tripped
Reset
Tripped
c
Reset
On
Position
d
43
21
76
3mm
42
Top
View
Front
Wheel
Page 6
196
ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench
and your own phillips screwdriver .
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
permanently damaged. Next, unplug the power cord.
CAUTION: You must be able to safely lift 20 kg (45
pounds) in order to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. CAUTION: To decrease the possibility of in-
jury, bend your legs and keep your back straight. As
you raise the treadmill, make sure to lift with your legs
rather than your back. Raise the treadmill about halfway
to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob
to the left and hold it. Raise the treadmill until the latch
pin is aligned with the hole in the catch. Insert the latch
pin into the catch. Make sure that the latch pin is fully
inserted into the catch.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the storage position in temperatures above 30¡ Celsius.
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the latch
pin is fully inserted into the catch.
1. Hold the handrails as shown and place one foot against a
wheel.
2. Tilt the treadmill back until it rolls freely on the front wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
3. Place one foot on the base, and carefully lower the tread-
mill until it is resting in the storage position.
HOW TO LOWER THE TREADMILL FOR USE
1. Refer to drawing 2 above. Hold the treadmill with your right hand as shown. Using your left hand, pull the latch
knob to the left and hold it. Pivot the treadmill down until the frame is past the pin. Slowly release the latch knob.
2. Refer to drawing 1. Hold the treadmill firmly with both hands, and lower the treadmill to the floor. CAUTION:
To decrease the possibility of injury, bend your legs and keep your back straight.
Base
Front Wheels
1
1. With the help of a second person, carefully raise the
treadmill to the upright position.
While a second person tips the treadmill to one side and
holds it, insert one of the Extension Legs (103) into the
treadmill as shown. Make sure that the Extension Leg is
turned so the Thick Base Pad (97) is on the bottom.
Next, tip the treadmill to the other side and insert the
other Extension Leg (not shown) in the same way. Lower
the side of the treadmill so that both Extension Legs
(103) are resting flat on the floor.
2. With the help of a second person, carefully tip the
Uprights (82) down as shown. Make sure that the
Extension Legs (103) remain in the Uprights.
Attach each Extension Leg (103) with two Screws (76)
and a Base Pad (118) as shown.
With the help of a second person, carefully tip the
Uprights (82) back to the vertical position.
Note: One replacement Base Pad (118) may be included. Use the Base Pad to replace any Base Pad that
becomes worn.
103
97
1
2
76
118
118
76
103
103
82
Latch
Knob
Pin
Catch
Closed
Open
2
Page 7
18
7
5. Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a
secure place. The allen wrench is used to adjust the walking belt (see page 21). To protect the floor or carpet
from damage, place a mat under the treadmill.
4
3. Locate the plastic tie in the post on the left Upright (82).
Hold a Handrail Extension (85) in the position shown.
Insert the plastic tie into the Handrail Extension as you
insert the Handrail Extension into the post. Attach the
Handrail Extension with three Screws (76). Note: The
plastic tie is tied to the Hand Pulse Wire (124). Be
careful to avoid damaging the Hand Pulse Wire. The
Hand Pulse Wire is used with the optional chest pulse
sensor (see page 18).
Slide a Handrail Foam Grip (110) onto the Handrail
Extension (85). (If it is difficult to slide on the Foam Grip,
place a small amount of warm water and dish soap in the
Foam Grip.) There are one or two holes in the bottom of
the Foam Grip. Press a Plastic Fastener (47) into each
hole.
Attach the other Handrail Extension and Handrail Foam
Grip to the right Upright (not shown). Note: There is not a
wire harness in the right Upright.
4. Make sure that the Lock Knob Sleeve (111) is fully inserted into the left Upright (82).
Remove the Lock Knob (102) from the Lock Pin (115).
Make sure that the Lock Pin Collar (113) and the Spring
(112) are on the Lock Pin. Insert the Lock Pin into the
left Upright (82) and tighten the Lock Knob onto it.
76
82
110
47
76
Post
85
124
Plastic Tie
3
113
115
111
112
102
82
Follow your progress with the LED track and
the four displays.
See step 5 on page 10.
Measure your pulse, if desired.
See step 6 on page 11.
When the program is finished, remove the
key.
Step onto the foot rails and remove the key from
the console. Keep the key in a secure place.
Note: If the displays and various indicators
on the console remain lit after the key is removed, the console is in the ÒdemoÓ mode.
Refer to the instructions at the right and turn
off the demo mode.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position.
THE INFORMATION MODE/DEMO MODE
The console features an information mode that keeps
track of the total number of hours that the treadmill has
been operated and the total number of miles that the
walking belt has moved. The information mode also
allows you to switch the console from miles per hour to
kilometers per hour. In addition, the information mode
allows you to turn on and turn off the demo mode.
To select the information mode, hold down the STOP
button while inserting the key into the console. When
the information mode is selected, the following information will be shown:
The DISTANCE/LAPS
display will show the total
number of miles that the
walking belt has moved.
The TIME/INCLINE/SEG
TIME display will show the
total number of hours the
treadmill has been used.
An ÒE,Ó for english miles, or an
ÒM,Ó for metric kilometers, will
appear in the SPEED/ MINMILE display. Press the
SPEED
▲▲
button to change
the unit of measurement.
IMPORTANT: The
CALS/FAT CALS/PULSE
display should be blank. If
a ÒdÓ appears in the display,
the console is in the ÒdemoÓ
mode. This mode is intended
to be used only when a treadmill is displayed in a store.
When the console is in the
demo mode, the power cord
can be plugged in, the key
can be removed from the
console, and the displays and
indicators on the console will
automatically light in a preset sequence, although the
buttons on the console will not operate. If a ÒdÓ appears
in the CALS/FAT CALS/PULSE display when the information mode is selected, press the SPEED
▼▼
button so the CALS/FAT CALS/PULSE display is
blank.
To exit the information mode, remove the key from the
console.
OPTIONAL HAND WEIGHTS
Optional hand weights let
you include upper-body exercise in your workouts.
The hand weights fit into
convenience holders in the
console. To purchase the
optional hand weights,
call the Customer Service
Department (see the back
cover of this manual).
OPTIONAL CHEST PULSE SENSOR
An optional chest pulse sensor adds even more
features to the console. The chest pulse sensor offers
hands-free operation and continuously monitors your
heart rate during your workouts. To purchase the
optional chest pulse sensor, call our Customer
Service Department (see the back cover of this
manual).
10
9
8
Page 8
178
HOW TO USE PROGRAMS DIRECTLY FROM
OUR INTERNET SITE
Our new internet site at www.iFit.com allows you to
access a large selection of programs that interactively
control your treadmill to help you achieve your specific
exercise goals. In addition, you can play iFit.com audio
and video programs directly from the internet. Explore
www.iFit.com for details.
To use programs from our internet site, the treadmill
must be connected to your home computer. See HOW
TO CONNECT YOUR COMPUTER on page 14. In addition, you must have at least a 56K modem and an
account with an internet service provider. A list of additional system and software requirements will be found
on our internet site.
Next, make sure that the
on/off switch near the
power cord is in the on
position. In addition,
make sure that the power
cord is properly plugged
in (see HOW TO PLUG IN THE POWER CORD on
page 8).
Follow the steps below to use a program from our
internet site.
Insert the key fully into the console.
When the key is
inserted, the four displays and various indicators on the console
will light.
Press the PROGRAM button.
When the key is inserted, the manual
mode will be selected.
To use a program from
our internet site, press
the PROGRAM button.
The iFit.com indicator
will light.
Go to your computer and start an internet
connection.
Start your web browser, if necessary, and go to
our internet site at www.iFit.com.
Follow the desired links on our internet site to
select a program.
Read and follow the on-line instructions for using a
program.
Follow the on-line instructions to start the
program.
When you start the program, an on-screen countdown will begin.
Return to the treadmill and stand on the foot
rails. Find the clip attached to the key and slide
the clip onto the waistband of your clothing.
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
Hold the handrails, step onto the walking belt, and
begin walking.
During the program, an electronic ÒchirpingÓ sound
will alert you when the speed and/or incline of the
treadmill is about to change. CAUTION: Always
listen for the ÒchirpÓ and be prepared for speed
and/or incline changes.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the SPEED or INCLINE buttons
on the console. However, when the next ÒchirpÓ
is heard, the speed and/or incline will change
to the next settings of the program.
To stop the program at any time, press the STOP
button on the console. The TIME/INCLINE/SEG
TIME display will begin to flash. To restart the program, press the START button or the SPEED
▲▲
button on the console. After a moment, the walking belt will begin to move at 1.0 mph. When the
next ÒchirpÓ is heard, the speed and incline
will change to the next settings of the
program.
When the program is completed, the walking belt
will stop and the TIME/INCLINE/SEG TIME display
will begin to flash. Note: To use another program,
press the STOP button and go to step 5 above.
Note: If the speed or incline of the treadmill
does not change when a ÒchirpÓ is heard, make
sure that the iFit.com indicator is lit and that
the TIME/INCLINE/SEG TIME display is not
flashing. In addition, make sure that the audio
cable is properly connected, that it is fully
plugged in, and that it is not wrapped around a
power cord.
7
6
5
4
3
2
1
On
Position
THE PERFORMANT LUBETMWALKING BELT
Your treadmill features a walking belt coated with PERFORMANT LUBETM, a high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. They will
deteriorate the walking belt and cause excessive wear.
HOW TO PLUG IN THE POWER CORD
This product must be earthed. If it should malfunction or break
down, earthing provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped
with a cord having an equipment-earthing conductor and a earthing plug.
Two power cords are included. Select the one that will fit your
outlet. Refer to drawing 1. Plug the indicated end of the
power cord into the socket on the treadmill. Refer to drawing
2. Plug the power cord into an appropriate outlet that is properly installed and earthed in accordance with all local codes
and ordinances. Note: In Italy, an adapter (not included) must
be used between the power cord and the outlet. Important: The
treadmill is not compatible with GFCI-equipped outlets.
Use only a power cord type H05VV-F with a conductor of at least
1mm2, with a country recognised plug and an appliance coupler.
DANGER: Improper connection of the
equipment-earthing conductor can result in an increased risk of electric shock. Check with a qualified
electrician or serviceman if you are in doubt as to
whether the product is properly earthed. Do not modify the plug provided with the productÑif it will not fit
the outlet, have a proper outlet installed by a qualified
electrician.
OPERATION AND ADJUSTMENT
Socket on treadmill
Outlet
1
2
Page 9
FEATURES OF THE CONSOLE
The treadmill console offers an impressive array of
features to help you get the most from your exercise.
When the console is in the manual mode, the speed
and incline of the treadmill can be controlled with a
touch of a button. As you exercise, the LED track and
the four displays will provide continuous exercise feedback. You can even measure your heart rate using the
built-in pulse sensor.
Six certified personal trainer programs are also offered.
Each program automatically controls the speed and incline of the treadmill as it guides you through an effective workout.
The console also features advanced iFit.com interactive technology. IFit.com technology is like having a
personal trainer right in your home. Using the included
audio cable, you can connect the treadmill to your
home stereo, portable stereo, or computer and play
special iFit.com CD programs (CDÕs are available separately). IFit.com CD programs automatically control
the speed and incline of the treadmill as a personal
trainer guides you through every step of your workout.
High-energy music provides added motivation. Each
CD features two different programs designed by certified personal trainers.
In addition, you can connect the treadmill to your VCR
and TV and play iFit.com video programs (videocassettes are available separately). IFit.com video programs offer the same benefits as iFit.com CD programs,
but add the excitement of working out with a class and
an instructorÑthe hottest new trend at health clubs.
With the treadmill connected to your computer, you
can also go to our new internet site at www.iFit.com
and access even more programs. Choose from a selection of basic programs that interactively control the
speed and incline of your treadmill to help you achieve
your personal exercise goals. Or, use iFit.com audio
and video programs directly from our internet site. Visit
www.iFit.com for complete details.
See www.iFit.com to learn about other iFit.com features. To purchase iFit.com CDÕs, iFit.com videocassettes, call toll-free 0345-089009. For information
about other optional accessories, see page 18.
To use the manual mode of the console, follow the
steps beginning on page 10. To use a personal trainer
program, see page 12. To use iFit.com CD or video
programs, refer to page 15. To use iFit.com programs directly from our internet site, see page 17.
CAUTION: Before operating the
console, read the following precautions.
¥ Do not stand on the walking belt when turn-
ing on the power.
¥ Always wear the clip (see the drawing
above) whilst operating the treadmill.
¥ Adjust the speed in small increments to
avoid sudden jumps in speed.
¥ To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and place only a sealed water
bottle in the water bottle holder.
916
CONSOLE DIAGRAM
Clip
Key
Program
Button
Incline
Buttons
Start
Button
Displays
Displays
i-Fit.com Indicator
Manual/Program Indicators
LED Track
Press the PLAY button on your CD player or
VCR.
A moment after the button is pressed, your personal trainer will begin guiding you through your
workout. Simply follow your personal trainerÕs instructions. Note: If the TIME/INCLINE/SEG TIME
display is flashing, press the START button or the
SPEED▲▲button on the console. The treadmill will
not respond to a CD or video program whilst the
TIME/INCLINE/SEG TIME display is flashing.
During the CD or video program, an electronic
ÒchirpingÓ sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the ÒchirpÓ and be
prepared for speed and/or incline changes. In
some instances, the speed and/or incline may
change before the personal trainer describes
the change.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the SPEED or INCLINE buttons
on the console. However, when the next ÒchirpÓ
is heard, the speed and/or incline will change
to the next settings of the CD or video program.
To stop the program at any time, press the STOP
button on the console. The TIME/INCLINE/SEG
TIME display will begin to flash. To restart the program, press the START button or the SPEED
▲▲
button again. After a moment, the walking belt will
begin to move at 1 mph. When the next ÒchirpÓ
is heard, the speed and incline will change to
the next settings of the CD or video program.
The program can also be stopped by pressing the
STOP button on your CD player or VCR.
When the CD or video program is completed, the
walking belt will stop and the TIME/INCLINE/SEG
TIME display will begin to flash. Note: To use another CD or video program, press the STOP button or remove the key and go to step 1 on page
15.
Note: If the speed or incline of the treadmill
does not change when a ÒchirpÓ is heard:
¥ make sure that the iFit.com indicator is lit and
that the TIME/INCLINE/SEG TIME display is
not flashing. If the TIME/INCLINE/SEG TIME
display is flashing, press the START button
or the SPEED ▲▲button on the console
¥ adjust the volume of your CD player or VCR. If
the volume is too high or too low, the console
may not detect the program signals
¥ make sure that the audio cable is properly
connected, that it is fully plugged in, and that
it is not wrapped around a power cord
¥ if you are using your portable CD player and
the CD skips, set the CD player on the floor or
another flat surface instead of on the console.
Follow your progress with the LED track and
the four displays.
See step 5 on page 10.
Measure your pulse, if desired.
See step 6 on page 11.
When the iFit.com CD or video program is
finished, remove the key.
Step onto the foot rails
and remove the key from
the console. Keep the
key in a secure place.
Note: If the displays
and various indicators
on the console remain lit after the key is removed, the console is in the ÒdemoÓ mode.
Refer to page 18 and turn off the demo mode.
CAUTION: Always remove iFit.com CDÕs and
videocassettes from your CD player or VCR
when you are finished using them.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position.
7
6
5
4
Stop
Button
Speed
Buttons
Page 10
10
15
STEP-BY-STEP CONSOLE OPERATION
Make sure that the on/off
switch near the power
cord is in the on
position. Next, make sure
that the key is removed
from the console and the
power cord is properly plugged in (see HOW TO PLUG
IN THE POWER CORD on page 8).
When you are ready to begin exercising, step onto the
foot rails of the treadmill. Find the clip attached to the
key (see the drawing on page 9), and slide the clip
onto the waistband of your clothing.
To use the manual mode of the console, follow the
steps below. To use a personal trainer program, see
page 12. To use iFit.com CD or video programs,
refer to page 15. To use iFit.com programs directly
from our internet site, see page 17.
Note: The console can display speed and distance in
either miles or kilometers (see SPEED/MIN-MILE DISPLAY on page 11). For simplicity, all instructions in this
manual refer to miles.
HOW TO USE THE MANUAL MODE
Insert the key fully into the console.
When the key is
inserted, the four displays and various indicators on the console
will light.
Select the manual mode.
When the key is inserted, the manual
mode will be selected
and the ÒMÓ indicator
will light. If a program
is selected, press the
PROGRAM button repeatedly to select the manual mode.
Press the START button or the SPEED
▲▲
button
to start the walking belt.
A moment after the button is pressed, the walking belt will begin to
move at 1 mph. Hold the
handrails and carefully
begin walking. As you
exercise, change the speed of the walking belt as
desired by pressing the SPEED buttons.
To stop the walking belt, press the STOP button.
The TIME/INCLINE/SEG TIME display will begin
to flash. To restart the walking belt, press the
START button or the SPEED ▲▲button.
Change the incline of the treadmill as desired.
To change the incline of
the treadmill, press the
INCLINE buttons. Each
time one of the buttons is
pressed, the incline will
change by 0.5%. The incline range is 1.5% to
12%. Note: When one of
the INCLINE buttons is pressed, the TIME/INCLINE/SEG TIME display will show the incline
setting for several seconds. After the buttons are
pressed, it may take a moment for the treadmill to
reach the selected incline setting.
Follow your progress with the LED track and
the four displays.
The LED TrackÑThe
LED track represents a
distance of 1/4 mile. As
you exercise, the indicators around the track will
light one at a time until
you have completed 1/4
mile. A new lap will then begin.
DISTANCE/LAPS displayÑThis display shows
the distance that you
have walked or run and
the number of laps you
have completed (one lap
equals 1/4 mile). The display will alternate
between one number and the other every seven
seconds, as shown by the arrows in the display.
TIME/INCLINE/SEG
TIME displayÑWhen the
manual mode or an
iFit.com program is selected, this display shows
the elapsed time. When a
personal trainer program is selected, this display
shows both the time remaining in the program and
the time remaining in the current segment of the
program. The display will alternate between one
number and the other every seven seconds. Each
time the INCLINE buttons are pressed, this display
shows the current incline setting.
5
4
3
2
1
On
Position
Arrow
HOW TO CONNECT YOUR VCR
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 14.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the AUDIO OUT jack on your
VCR.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA adapter (available at
electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the
RCA adapter. Plug the RCA adapter into the AUDIO
OUT jack on your VCR.
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS
To use iFit.com CDÕs or videocassettes, the treadmill
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or
VCR. See HOW TO CONNECT THE COMPUTER TO
YOUR CD PLAYER, VCR, OR COMPUTER on page
13. Note: To purchase iFit.com CDÕs or to purchase
iFit.com videocassettes, call 0345-089009.
Make sure that the on/off
switch near the power cord
is in the on position. In
addition, make sure that the
power cord is properly
plugged in (see HOW TO
PLUG IN THE POWER CORD on page 8).
When you are ready to begin exercising, step onto the
foot rails of the treadmill. Find the clip attached to the
key (see the drawing on page 9), and slide the clip
onto the waistband of your clothing. Follow the steps
below to use an iFit.com CD or video. Note: The in-
structions included in the CD case describe how to
use the CD with a variety of PROFORM treadmills.
Some instructions may not apply to this treadmill.
Insert the key fully into the console.
When the key is
inserted, the four displays
and various indicators
on the console will light.
Press the PROGRAM button.
When the key is inserted, the manual
mode will be selected.
To use an iFit.com CD
or video program, press
the PROGRAM button.
The iFit.com indicator
will light.
Insert the iFit.com CD or videocassette.
If you are using an iFit.com CD, insert the CD into
your CD player. If you are using an iFit.com videocassette, insert the videocassette into your VCR.
3
2
1
AUDIO OUT
RIGHT
LEFT
VIDEO AUDIO
ANT. IN
RF OUT
IN
OUT
CH
34
Audio
Cable
Adapter
A
VIDEO AUDIO
ANT. IN
RF OUT
IN
OUT
CH
34
Audio
Cable
Adapter
B
Wire removed from
AUDIO OUT jack
RCA Adapter
On
Position
t
.
Program
Button
Start Button
Page 11
14
11
CALS/FAT CALS/
PULSE displayÑThis
display shows the approximate numbers of
calories and fat calories
you have burned (see
FAT BURNING on page 22). Every seven seconds, the display will change from one number to
the other, as shown by the arrows in the display.
This display will also show your heart rate when
the pulse sensor is used (see step 6 on this page).
SPEED/MIN-MILE
displayÑThis display
shows the speed of the
walking belt and your
current pace (pace is
measured in minutes per
mile). Every seven seconds, the display will
change from one number to the other, as shown
by the arrows in the display.
Note: The SPEED/MIN-MILE display can show
speed in either miles per hour or kilometers per
hour. To determine which unit of measurement is
selected, hold down the STOP button while inserting the key into the console. An ÒE,Ó for english
miles, or an ÒM,Ó for metric kilometers, will appear
in the display. Press the
SPEED
▲▲
button to
change the unit of measurement. When the desired unit of measurement is selected, remove and then reinsert the
key. Note: For simplicity, all instructions in this
manual refer to miles.
Note: To reset the displays, press the STOP button, remove the key, and then reinsert the key.
Measure your pulse, if desired.
Stand on the
foot rails and
place your
hands on the
metal contacts
on the pulse bar.
Your palms
must be resting
on the upper
contacts, and
your fingers must
be touching the
lower contactsÑ
avoid moving
your hands.
When your pulse
is detected, the heart-shaped indicator in the
CALS/FAT CALS/PULSE display will flash
steadily and a series of dashes (Ñ Ñ) will appear. After a few seconds, your heart rate will be
shown. For the most accurate heart rate read-
ing, continue to hold the contacts for about 15
seconds.
When you are finished exercising, remove the
key.
Step onto the foot rails,
press the STOP button,
and remove the key from
the console. Keep the
key in a secure place.
Note: If the displays
and various indicators on the console remain
lit after the key is removed, the console is in
the ÒdemoÓ mode. Refer to page 18 and turn off
the demo mode.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position.
7
6
Sensors
HOW TO CONNECT YOUR HOME STEREO
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the LINE OUT jack on your
stereo.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA adapter (available at
electronics stores). Next, remove the wire that is
currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
RCA adapter. Plug the RCA adapter into the LINE
OUT jack on your stereo.
HOW TO CONNECT YOUR COMPUTER
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your computer.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your computer. Plug your
headphones or speakers into the other side of the
Y-adapter.
CD
VCR
Amp
LINE OUT
LINE OUT
Audio
Cable
Adapter
A
LINE OUT
Audio
Cable
A
CD
VCR
Amp
LINE OUT
Audio
Cable
RCA
Adapter
Wire removed from
LINE OUT jack
B
Adapter
PHONES
Audio
Cable
B
3.5mm
Y-adapter
Headphones/Speakers
Page 12
12
13
HOW TO CONNECT THE TREADMILL TO YOUR
CD PLAYER, VCR, OR COMPUTER
To use iFit.com CDÕs, the treadmill must be con-
nected to your portable CD player, portable stereo,
home stereo, or computer with CD player. See pages
13 and 14 for connecting instructions. To use iFit.com
videocassettes, the treadmill must be connected to
your VCR. See page 15 for connecting instructions. To
use iFit.com programs directly from our internet
site, the treadmill must be connected to your home
computer. See page 14 for connecting instructions.
HOW TO CONNECT YOUR PORTABLE CD PLAYER
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your CD player. Plug your headphones into the
PHONES jack.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your CD player. Plug your
headphones into the other side of the Y-adapter.
HOW TO CONNECT YOUR PORTABLE STEREO
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter. Plug
the adapter into an AUDIO OUT jack on your stereo.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your stereo.
C. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your stereo. Plug your
headphones into the other side of the Y-adapter.
LINE OUT
PHONES
LINE OUT
PHONES
Audio
Cable
Head-
phones
A
AUDIO OUT
RIGHT
LEFT
Audio
Cable
Adapter
A
LINE OUT
Audio
Cable
B
PHONES
Audio
Cable
C
PHONES
PHONES
Audio
Cable
3.5mm
Y-adapter
Headphones
B
3.5mm
Y-adapter
Headphones
HOW TO USE PERSONAL TRAINER PROGRAMS
Insert the key into the console.
When the key is inserted, the four displays
and various indicators
on the console will light.
Select one of the personal trainer programs.
When the
key is inserted, the
manual
mode will be
selected and
the ÒMÓ indicator will
light. To select one of
the personal
trainer programs, press the PROGRAM button repeatedly until one of the six personal trainer program indicators lights.
The console features two LOW INTENSITY programs, two MEDIUM INTENSITY programs, and
two HIGH INTENSITY programs. The profiles on
the console show how the speed and incline of
the treadmill will change during the programs. The
numbers beside the profiles show the maximum
speed and incline settings for the programs. For
example, the upper left profile shows that the
treadmill will reach a maximum speed of 4.5 mph
and a maximum incline of 5% during the first program.
Press the START button or the SPEED
▲▲
button
to start the program.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
Each program is divided
into several time
segments of different
lengths. The TIME/
INCLINE/SEG TIME
display shows both the
time remaining in the program and the time
remaining in the current segment of the program.
One speed setting and one incline setting are programmed for each segment. When only three seconds remain in the first segment, a series of tones
will sound and the treadmill will automatically adjust to the speed and incline settings for the second
segment.
The program will continue in this way until the
TIME/INCLINE/SEG TIME display counts down to
zero. The walking belt will then slow to a stop.
If the speed or incline setting for the current segment is too high or too low, you can manually
override the settings by pressing the SPEED or
INCLINE buttons on the console. However, when
the next segment begins, the treadmill will adjust to the next speed and incline settings of
the program.
To stop the program, press the STOP button. The
TIME/INCLINE/SEG TIME display will begin to
flash. To restart the program, press the START
button or the SPEED ▲▲button. To end the program, press the STOP button, remove the key,
and then reinsert the key.
Follow your progress with the LED track and
the four displays.
Refer to step 5 on page 10.
Measure your pulse, if desired.
See step 6 on page 11.
When the program is completed, remove the
key from the console.
When the program has
ended, remove the key
from the console. Keep
the key in a safe place.
Note: If the displays
and indicators on the
console remain lit after the key is removed, the
console is in the ÒdemoÓ mode. Refer to page
18 and turn off the demo mode.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position.
6
5
4
3
2
1
Program Button
Page 13
62
17
52
106
16
16
49
24
89
70
100
41
29
69
30
62
26
125
119
15
8
122
7
13
19
119
5
15
35
36
32
33
15
31
38
39
15
15
76
18
119
22
21
3
1
3
4*
2
39
40
92
33
43
42
32
68
44
45
46
41
71
55
68
44
101
101
47
45
46
47
47
62
53
54
59
60
62
61
64
65
101
59
47
63
57
67
51
15
10
11
10
14
9
66
36
65
36
68
68
12
75
75
37
74
37
81
98
93
88
101
101
120
6
37
25
69
48
58
78
27
62
126
78
118
127
128
EXPLODED DRAWINGÑModel No. PETL61591 R1000A
SAVE THE EXPLODED DRAWING
FOR FUTURE REFERENCE.
To identify the parts shown on this exploded drawing, refer to the
PART LIST on page 23 of the USERÕS MANUAL.
Page 14
108
107
109
87
77
89
89
46
46
116
50
117
117
89
20
97
101
103
119
97
101
96
97
101
83
83
82
84
16
84
94
101
91
99
69
104
86
15
95
72
76
105
76
86
95
47
16
34
56
23
80
73
97
101
103
104
20
47
110
15
110
108
107
85
101
46
46
90
101
121**
79
79
124
124
28*
28*
123
123
97
97
129**
130**
102
111
112
113
114
115
EXPLODED DRAWINGÑModel No. PETL61591 R1000A
Loading...