Model No. PFBE1516.0
Visit our website at
www.proform.com
new products, prizes,
fitness tips, and much more!
Serial No.
Write the serial number in the
space above for future reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if a part is
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
USER’S MANUAL
CALL TOLL-FREE:
1-888-533-1333
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
www.proformservice.com
CAUTION
Read all precautions and instruc
tions in this manual before using
this equipment. Save this manual
for future reference.
-
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
PROFORM is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read the following important precautions
efore using the weight bench.
b
1
. Read all instructions in this manual
warnings on the weight bench
t
he weight bench. Use the weight bench only
as described in this manual.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are adequately informed of all precautions.
3. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.
4.
Keep the weight
moisture and dust. Place the weight
a level surface, with a mat beneath it to protect the floor or carpet. Make sure that there is
enough clearance around the weight
mount, dismount, and use the weight
5. Keep children under 12 and pets away from
the weight bench at all times.
6.
Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
bench
indoors, away from
and all
before using
bench
bench
bench
on
to
.
10.
I
f you feel pain or dizziness at any time while
exercising, stop immediately and begin cooling down.
The decals shown below have been placed
1
1.
on the weight bench. If a decal is missing or
illegible, call the toll-free telephone number
on the front cover of this manual and order a
free replacement decal. Apply the decal in the
location shown.
7.
Always make sure that the backrest knob is
fully engaged before using the backrest.
8.
Wear appropriate clothes when exercising.
Always wear athletic shoes for foot protection while exercising.
9.
The weight bench is designed to support a
maximum user weight of 300 pounds and a
maximum total weight of 510 pounds. Do not
use the weight bench with more than 210
pounds of weight. Do not place more than
130 pounds on the leg lever. Note: The weight
bench does not include weights.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
BEFORE YOU BEGIN
hank you for selecting the versatile PROFORM
T
FUSION 1.6 X weight bench. The weight bench offers
a selection of exercise stations designed to develop
the major muscle group of the upper body. Whether
your goal is to tone your body, build dramatic muscle
ize and strength, or improve your cardiovascular sys-
s
tem, the weight bench will help you to achieve the
specific results you want.
For your benefit, read this manual carefully before
using the weight bench. If you have questions after
reading this manual, please see the front cover of this
Upright
Weight Rest
®
anual. To help us assist you, please note the product
m
model number and serial number before contacting us.
The model number is PFBE1516.0. The serial number
can be found on a decal attached to the weight bench
(see the front cover of this manual).
To avoid a registration fee for any service needed
under warranty, you must register the weight bench
at www.proformservice.com/registration.
Before reading further, please review the drawing below
and familiarize yourself with the parts that are labeled.
ASSEMBLED DIMENSIONS:
Height: 60 in. / 152 cm
Width: 42 in. / 107 cm
Depth: 78 in. / 198 cm
Pin
Curl Pad
Leg Lever
Curl Bar
Curl Pin
Olympic
Adapter
Backrest
Seat
Backrest Bracket
4
M6 Washer (46)
M8 Washer (58)
M10 Nylon
Locknut (43)
M8 x 10mm Set
Screw (55)
M10 x 70mm Button Bolt (48)
M6 x 63mm Screw (54)
M10 x 175mm Bolt (51)
M8 x 45mm Bolt (52)
M6 x 23mm
Screw (53)
M6 x 48mm Screw (56)
M10 x 80mm Button Screw (59)
M8 x 16mm
Bolt (60)
M4 x 12mm
Self-tapping
Screw (61)
M10 Washer (45)
M8 Nylon
Locknut (44)
M10 x 57mm Bolt Set (49)
M10 x 55mm Button Screw (50)
M10 x 90mm Button Screw (47)
PART IDENTIFICATION CHART
See the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is
the key number of the part, from the PART LIST on page 18. Note: Some small parts may have been pre-
attached. If a part is not in the parts bag, check to see if it has been preattached.
5
ASSEMBLY
Make Assembly Easier
Everything in this manual is designed to ensure
that the weight bench can be assembled successfully by almost anyone. However, the weight
bench has many parts and the assembly
process will take time. By setting aside plenty of
time, assembly will go smoothly.
To hire an authorized service technician to
assemble the weight bench, call toll-free
1-800-445-2480.
Before beginning assembly
following information and instructions:
Because of its weight and size, the weight bench
•
should be assembled in the location where it will
be used. Make sure that there is enough clearance to walk around the weight bench as you
assemble it.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
, carefully read the
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
• As you assemble the weight bench, make sure all
arts are oriented as shown in the drawings.
p
• Assembly requires two persons.
• For help identifying small parts, use the PART
IDENTIFICATION CHART.
In addition to the included grease, assembly
may require the following tools (not included):
• Two adjustable wrenches
• One rubber mallet
• One standard screwdriver
• One Phillips screwdriver
Assembly may be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
1.
Before beginning assembly, make sure that
you have read and understand the information in the box above. See the PART IDENTIFICATION CHART for help identifying small
parts.
Attach the Support (5) to the Base (1) with an
M10 x 55mm Button Screw (50) and two M10 x
80mm Button Screws (59).
Orient the Base Foot (22) with the grooves in the
position shown. Attach the Base Foot to the Base
(1) with an M4 x 12mm Self-tapping Screw (61).
1
5
50
1
59
22
61
59
Grooves
6
2. Orient the Left Upright (6) with the indicated holes
CurlKnob(35)
SeatFrameKnob (62)
facing the direction shown. Attach the Crossbar
4) to the Left Upright with two M10 x 90mm
(
Button Screws (47) and two M10 Washers (45).
o not tighten the Button Screws yet.
D
Attach the Crossbar (4) to the Right Upright (7)
with two M10 x 90mm Button Screws (47) and
wo M10 Washers (45). Do not tighten the
t
Button Screws yet.
2
7
4
7
45
6
47
3. Attach the Crossbar (4) to the Support (5) with an
M10 x 55mm Button Screw (50), two M10 x
80mm Button Screws (59), and two M10 Washers
Do not tighten the Button Screws Yet.
(45).
Attach the Base (1) to the Left and Right Uprights
(6, 7) with four M10 x 90mm Button Screws (47)
and four M10 Washers (45).
Tighten the Button Screws (47, 50, 59) used in
step 2 and this step.
Attach the Left and Right Upright Feet (15, 17) to
the Left and Right Uprights (6, 7) with four M4 x
12mm Self-tapping Screws (61).
45
47
4
Holes
3
47
7
59
17
45
45
6
61
47
50
5
4
47
45
1
15
61
4. Orient the Crossbar Cap (21) as shown in the top
inset drawing. Press the Crossbar Cap onto the
Crossbar (4). Apply a small amount of the included grease to an M10 x 80mm Button Screw (59).
Attach the Seat Frame (2) to the Support (5) with
the Button Screw and an M10 Nylon Locknut (43).
See the bottom inset drawing and identify the
Seat Frame Knob (62). Tighten the Seat Frame
Knob into the Seat Frame (2).
ighten the Backrest Knob (36) into the Seat
T
Frame (2).
4
Front
62
36
2
21
Front
4
59
43
62
35
5
7
5. See the inset drawing. Orient the Front Leg Foot
(19) and the Front Leg (3) as shown. Press the
Front Leg Foot onto the Front Leg.
ttach the Front Leg Foot (19) to the Front Leg (3)
A
with two M4 x 12mm Self-tapping Screws ( 61).
Next, attach the Front Leg to the Seat Frame (2)
with two M10 x 70mm Button Bolts (48), two M10
Washers (45), and an M10 Nylon Locknut (43).
5
2
5
4
48
43
3
19
61
3
Tall
Side
19
6. Attach the Backrest Bracket (8) to the two
Backrest Frames (9) with four M8 x 45mm Bolts
(52), four M8 Washers (58), and four M8 Nylon
Locknuts (44). Do not tighten the Nylon
Locknuts yet.
Orient the Backrest (18) with the wide end in the
position shown. Attach the Backrest to the
Backrest Frames (9) with four M6 x 48mm Screws
(56) and four M6 Washers (46). Do not tighten
the Screws yet.
7. Pull the Backrest Knob (36) out as far as it will
go. Insert the Backrest Bracket (8) into the slot in
the Seat Frame (2). Then, engage the Backrest
Knob into the Backrest Bracket.
6
46
44
56
18
9
9
46
56
58
52
44
8
Wide
End
52
58
7
Apply grease to an M10 x 175mm Bolt (51).
Attach the Backrest Frames (9) to the Seat
Frame (2) with the Bolt, two M10 Washers (45),
and an M10 Nylon Locknut (43).
tighten the Nylon Locknut; the Seat Bracket
and the Backrest Frames must be able to
pivot easily.
See the inset drawing. Insert an M8 x 16mm
Bolt (60) into the Backrest Bracket (8). Tighten an
M8 Nylon Locknut (44) onto the Bolt.
Tighten the M8 Nylon Locknuts (44) and the
M6 x 48mm Screws (56) used in step 6.
Do not over-
9
45
8
36
45
2
43
44
8
60
Grease
51
8
8. Orient the Seat (16) as shown. Attach the Seat to
the Seat Frame (2) with two M6 x 23mm Screws
53), an M6 x 63mm Screw (54), and an M6
(
Washer (46).
8
16
2
46
53
54
9. Apply grease to the barrel of the M10 x 57mm
Bolt Set (49) and to the face of each Bushing
(30). Attach the Leg Lever (10) to the Front Leg
(3) with the Bolt Set.
Bolt Set is inserted through both sides of the
bracket on the Leg Lever.
10. Insert a Pad Tube (14) into the Leg Lever (10).
Slide a Foam Pad (40) onto each end of the Pad
Tube. Then, press a Pad Cap (24) into each
Foam Pad.
Repeat this step with the other two Pad T
(14).
Make sure the barrel of the
ubes
9
10
24
Grease
10
40
49
14
Grease
30
Grease
Bracket
49
3
14
10
14
40
24
9
1. Attach the Curl Bumper (39) to the Curl Bar (11)
Pin(34)
CurlPin (38)
Pin(34)
CurlPin (38)
1
with an M4 x 12mm Self-tapping Screw (61).
1
1
See the inset drawing and identify the Curl Pin
38).Attach the Curl Bar (11) to the Leg Lever (10)
(
with the Curl Pin. Attach the Curl Pin to the Leg
Lever with an M4 x 12mm Self-tapping Screw (61).
12. See the inset drawing and identify the Pins
(34).
Slide a Weight Rest (13) onto the Right Upright
(7). Insert a Pin (34) through the Weight Rest and
the Right Upright. Next, attach the Pin to the
Weight Rest with an M4 x 12mm Self-tapping
Screw (61).
Repeat this step for the other side of the
weight bench.
12
11
9
3
1
6
38
61
10
34
38
13
34
7
61
13. Attach the Curl Pad (20) to the Curl Post (12) with
two M6 x 23mm Screws (53).
14. Make sure that all parts are properly tightened
before the weight bench is used. The use of the
remaining parts will be explained in ADJUSTMENTS, beginning on the next page.
10
13
34
38
20
12
53
ADJUSTMENTS
This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 13 for impor-
ant information about how to get the most benefit from your exercise program. Also, refer to the accompanying
t
exercise guide to see the correct form for each exercise.
Make sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediate-
y. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
l
ADJUSTING THE BACKREST
To adjust the position of the Backrest (18), pull the
Backrest Knob (36) out of the Seat Frame (2) as far
as it will go. Raise or lower the Backrest, and reengage the Backrest Knob into the Backrest Bracket (8).
USING THE CURL PAD
To use the Curl Pad (20), remove the indicated 50mm
Round Inner Cap (25) and insert the Curl Post (12)
into the Front Leg (3). Tighten the Curl Knob (35) into
the Front Leg. Make sure that the Curl Knob passes
through a hole in the Curl Post.
When performing exercises that do not require the
Curl Pad (20), remove the Curl Pad and reinsert the
50mm Round Inner Cap (25) into the Front Leg (3).
18
36
2
8
20
12
25
35
USING THE LEG LEVER
The Leg Lever (10) can be used with standard
weights or Olympic weights. To use standard weights,
slide a weight plate (not shown) onto the Leg Lever
and secure it with a 1" Spring Clip (41).
If you are using Olympic weights, slide the Olympic
Adapter (37) onto the Leg Lever (10).
Olympic
Use a 2" Spring Clip (42) to secure the weight plates.
Note: Remove the Curl Bar (1
Leg Lever (10).
Adapter with an M8 x 10mm Set Screw (55).
1) when using the
Attach the
11
42
37
3
11
10
41
55
ADJUSTING THE WEIGHT RESTS
To adjust the position of the Weight Rests (13),
remove the Pins (34) from the Left and Right Uprights
(6, 7). Raise or lower the Weight Rests to the desired
position. Reengage the Pins into the Weight Rests
and the Left and Right Uprights. Make sure that the
Weight Rests are at the same height.
REMOVING THE CURL BAR
To remove the Curl Bar (11), remove the Curl Pin (38)
from the Leg Lever (10).
13
11
34
6
7
10
34
3
1
STORING THE WEIGHT BENCH
Remove the Seat Frame Knob (62) from the Seat
Frame (2), and lift the weight bench to the position
shown. Insert the Seat Frame Knob into the indicated
hole in the Support (5) and the Seat Frame. Make
sure that the Seat Frame Knob is inserted through
the Seat Frame.
38
2
Hole
5
62
12
EXERCISE GUIDELINES
HE FOUR BASIC TYPES OF WORKOUTS
T
Muscle Building
To increase the size and strength of your muscles,
ush them close to their maximum capacity. Your mus-
p
cles will continually adapt and grow as you progressively increase the intensity of your exercise. You can
adjust the intensity level of an individual exercise in
two ways:
• by changing the amount of resistance used
• by changing the number of repetitions or sets per-
formed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)
The proper amount of resistance for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of resistance that is
right for you. Begin with 3 sets of 8 repetitions for each
exercise you perform. Rest for 3 minutes after each
set. When you can complete 3 sets of 12 repetitions
without difficulty, increase the amount of resistance.
Toning
You can tone your muscles by pushing them to a moderate percentage of their capacity. Select a moderate
amount of resistance and increase the number of repetitions in each set. Complete as many sets of 15 to
20 repetitions as possible without discomfort. Rest for
1 minute after each set. Work your muscles by completing more sets rather than by using high amounts of
resistance.
eight Loss
W
To lose weight, use a low amount of resistance and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
Cross Training
Cross training is an ef
well-balanced fitness program. An example of a balanced program follows:
• Plan strength training workouts on Monday,
ednesday
W
Plan 20 to 30 minutes of aerobic exercise, such as
•
running on a treadmill or riding on an elliptical exer
ciser or exercise cycle, on Tuesday and Thursday.
Rest from both strength training and aerobic exercise
•
for at least one full day each week to give your body
time to regenerate.
The combination of strength training and aerobic exer
cise will reshape and strengthen your body, plus develop your heart and lungs.
, and Friday.
ficient way to get a complete and
-
ERSONALIZING YOUR EXERCISE PROGRAM
P
Determining the exact length of time for each workout,
as well as the number of repetitions or sets completed,
s an individual matter. It is important to avoid overdo-
i
ing it during the first few months of your exercise program. You should progress at your own pace and be
sensitive to your body’s signals. If you experience pain
or dizziness at any time while exercising, stop immediately and begin cooling down. Find out what is wrong
before continuing. Remember that adequate rest and a
proper diet are important factors in any exercise program.
WARMING UP
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. W
your body for more strenuous exercise by increasing
circulation, raising your body temperature and delivering more oxygen to your muscles.
WORKING OUT
Each workout should include 6 to 10 different exercises. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
EXERCISE FORM
Maintaining proper form is an essential part of an
effective exercise program. This requires moving
through the full range of motion for each exercise, and
moving only the appropriate parts of the body
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompanying this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles af
next page to find the names of the muscles.
The repetitions in each set should be performed
smoothly and without pausing.
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
-
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath.
fected. Refer to the muscle chart on the
arming up prepares
The exertion stage of
.
13
Rest for a short period of time after each set. The
O
P
Q
R
S
T
U
V
X
W
N
M
J
G
F
H
I
K
E
C
D
B
A
L
MUSCLE CHART
A. Sternomastoid (neck)
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
E. Brachioradials (forearm)
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
L. Anterior Deltoid (shoulder)
M. Rectus Abdominus (stomach)
N. Adductor (inner thigh)
O. Trapezius (upper back)
P. Rhomboideus (shoulder)
Q. Posterior Deltoid (Upper Back)
R. Triceps (back of arm)
S. Latissimus Dorsi (mid back)
T. Spinae Erectors (lower back)
U. Gluteus Medius (hip)
V. Gluteus Maximus (buttocks)
W. Hamstring (back of leg)
X. Gastrocnemius (back of calf)
deal resting periods are:
i
• Rest for three minutes after each set for a muscle
uilding workout.
b
• Rest for one minute after each set for a toning work-
out.
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
slowly as you stretch and do not bounce. Ease into
ach stretch gradually and go only as far as you can
e
without strain. Stretching at the end of each workout
s an effective way to increase flexibility.
i
STAYING MOTIVATED
For motivation, keep a record of each workout. List the
date, the exercises performed, the resistance used,
and the numbers of sets and repetitions completed.
Make copies of the exercise logs found on pages 15
and 16. Use the logs to record your weight and key
body measurements at the end of every month.
Remember, the key to achieving the greatest results is
to make exercise a regular and enjoyable part of your
everyday life.
14
MONDAY
ate:
D
/
EXERCISE WEIGHT SETS REPS
/
TUESDAY
Date:
/ /
WEDNESDAY
Date:
/ /
THURSDAY
Date:
/ /
AEROBIC EXERCISE
EXERCISE WEIGHT SETS REPS
AEROBIC EXERCISE
FRIDAY
Date:
EXERCISE WEIGHT SETS REPS
/ /
Make photocopies of this page for scheduling and recording your workouts.
15
MONDAY
ate:
D
/
EXERCISE WEIGHT SETS REPS
/
TUESDAY
Date:
/ /
WEDNESDAY
Date:
/ /
THURSDAY
Date:
/ /
AEROBIC EXERCISE
EXERCISE WEIGHT SETS REPS
AEROBIC EXERCISE
FRIDAY
Date:
EXERCISE WEIGHT SETS REPS
/ /
Make photocopies of this page for scheduling and recording your workouts.
16
NOTES
17
PART LIST—Model No. PFBE1516.0 R0606A
Key No. Qty. Description Key No. Qty. Description
1 1 Base
2 1 Seat Frame
3
4 1 Crossbar
5 1 Support
6 1 Left Upright
7 1 Right Upright
8 1 Backrest Bracket
9 2 Backrest Frame
10 1 Leg Lever
11 1 Curl Bar
12 1 Curl Post
13 2 Weight Rest
14 3 Pad Tube
15
16 1 Seat
17 1 Right Upright Foot
18 1 Backrest
19 1 Front Leg Foot
20 1 Curl Pad
21 1 Crossbar Cap
22 1 Base Foot
23 2 70mm Round Inner Cap
24 6 Pad Cap
25 1 50mm Round Inner Cap
26 2 45mm Round Inner Cap
27 3 25mm Round Inner Cap
28 1 25mm Round Outer Cap
29 1 Olympic Adapter Cap
30 4 Bushing
31 4 38mm Round Inner Cap
32 4 25mm Square Inner Cap
33
34 2 Pin
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts.
1 Front Leg
1 Left Upright Foot
4 Weight Rest Bushing
35 1 Curl Knob
36 1 Backrest Knob
7 1 Olympic Adapter
3
38 1 Curl Pin
39 1 Curl Bumper
40 6 Foam Pad
41 1 1" Spring Clip
42 1 2" Spring Clip
43 3 M10 Nylon Locknut
44 5 M8 Nylon Locknut
45 14 M10 Washer
46 5 M6 Washer
47 8 M10 x 90mm Button Screw
48 2 M10 x 70mm Button Bolt
49
50 2 M10 x 55mm Button Screw
51 1 M10 x 175mm Bolt
52 4 M8 x 45mm Bolt
53 4 M6 x 23mm Screw
54 1 M6 x 63mm Screw
55 1 M8 x 10mm Set Screw
56 4 M6 x 48mm Screw
57 1 50 x 38mm Inner Cap
58 4 M8 Washer
59 5 M10 x 80mm Button Screw
60 1 M8 x 16mm Bolt
61 11 M4 x 12mm Self-tapping Screw
62 1 Seat Frame Knob
63 3 Tether
# 1 User’s Manual
# 1 Exercise Guide
# 4 Hex Key
#
1 M10 x 57mm Bolt Set
1 Grease Pack
18
1
2
3
4
5
6
7
8
9
9
10
11
12
13
13
14
14
16
18
15
17
21
22
23
23
24
24
24
24
24
25
26
26
27
27
28
29
30
30
30
30
31
31
32
32
33
33
33
33
34
34
38
35
62
36
37
41
42
20
43
44
44
43
43
45
45
45
58
46
46
58
45
45
45
45
47
47
47
47
48
48
49
49
59
59
59
59
45
45
59
51
52
56
56
53
46
54
53
61
55
61
61
19
40
40
40
40
40
52
60
44
50
50
61
61
61
61
39
31
31
61
57
63
63
63
EXPLODED DRAWING—Model No. PFBE1516.0 R0606A
19
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, please be prepared
o give the following information:
t
• the MODEL NUMBER of the product (PFBE1516.0)
the NAME of the product (PROFORM FUSION 1.6 X weight bench)
•
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING on
pages 18 and 19)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped
to a service center, freight charges to and from the service center will be the customer’s responsibility. For
in-home service, the customer will be responsible for a minimal trip charge. This warranty does not extend
to any product or damage to a product caused by or attributable to freight damage, abuse, misuse,
improper or abnormal usage or repairs not provided by an ICON authorized service center; products used
for commercial or rental purposes; or products used as store display models. No other warranty beyond
that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss
of property
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
This warranty gives you specific legal rights.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 241117 R0606A Printed in China © 2006 ICON IP, Inc.
ou may also have other rights which vary from state to state.
Y
Loading...