Page 1
USER'S MANUAL
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
Serial
Number
Decal
Model No. PFEVEX2416.0
Serial No.
QUESTIONS?
As a manufacturer, we are
committed to providing complete customer satisfaction. If
you have questions, or if
there are missing or damaged
parts, please call:
Or write:
ICON Health & Fitness, Ltd.
Unit 4
Revie Road Industrial Estate
Revie Road, Beeston
Leeds, LS11 8JG
UK
email: csuk@iconeurope.com
08457 089 009
Visit our website at
www.iconeurope.com
Page 2
2
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
HOW TO OPERATE THE EXERCISE CYCLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
1. Read all instructions in this manual before
using the exercise cycle.
2. It is the responsibility of the owner to ensure
that all users of the exercise cycle are adequately informed of all precautions. Use the
exercise cycle only as described in this manual.
3. The exercise cycle is intended for home use
only. Do not use the exercise cycle in
a commercial, rental, or institutional setting.
4. Use the exercise cycle indoors on a level surface. Keep the exercise cycle away from
moisture and dust. Place a mat under the
exercise cycle to protect the floor.
5. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
6. Keep children under the age of 12 and pets
away from the exercise cycle at all times.
7. Wear appropriate clothes when exercising;
do not wear loose clothes that could become
caught on the exercise cycle. Always wear
athletic shoes for foot protection.
8. The exercise cycle should not be used by
persons weighing more than 113 kg (250 lbs).
9. Always keep your back straight when using
the exercise cycle; do not arch your back.
10. If you feel pain or dizziness while exercising,
stop immediately and cool down.
11. The exercise cycle does not have a freewheel;
the pedals will continue to move until the flywheel stops.
12.The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
13.A warning decal has been placed on the exercise cycle in the location shown on page 3. If
the decal is missing or illegible, call the telephone number on the front cover of this manual and order a free replacement decal. Apply
the decal in the location shown.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precau-
tions before using the exercise cycle.
Page 3
3
Congratulations for selecting the new PROFORM®710
EKG exercise cycle. Cycling is one of the most effective exercises for increasing cardiovascular fitness,
building endurance, and toning the entire body. The
710 EKG exercise cycle offers a selection of features
designed to let you enjoy this healthful exercise in the
convenience and privacy of your home.
For your benefit, read this manual carefully before
you use the exercise cycle. If you have questions
after reading this manual, please see the front cover
of this manual. To help us assist you, note the product
model number and serial number before contacting
us. The model number is PFEVEX2416.0. The serial
number can be found on a decal attached to the exercise cycle (see the front cover of this manual for the
location of the decal).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Handlebar
REAR
Seat
Adjustment Knob
Seat Knob
Pedal/Strap
Console
Water Bottle
Holder*
Wheel
*Water bottle not included
Pulse Sensor
Adjustment Handle
RIGHT SIDE
FRONT
BEFORE YOU BEGIN
Page 4
4
ASSEMBLY
Assembly requires two persons. Place all parts of the exercise cycle in a cleared area and remove the packing
materials. Do not dispose of the packing materials until assembly is completed.
Assembly requires the included tools and your own adjustable wrench and Phillips
screwdriver .
Use the part drawings below to identify the small parts used in assembly. The number in parentheses below
each drawing refers to the key number of the part, from the PART LIST on page 18. The second number refers
to the quantity needed for assembly. Note: Some small parts may have been preattached for shipping. If a
part is not in the parts bag, check to see if it has been preattached.
1. Identify the Front Stabilizer (2), which has round
wheels. While another person lifts the front of the
Frame (1), attach the Front Stabilizer to the Frame
with two M10 x 73mm Button Screws (33) and two
M10 Split Washers (34).
2
33
34
34
1
1
M4 x 15mm
Screw (15)–2
M10 x 20mm Button
M4 x 15mm
Screw (40)–4
Screw (35)–3
M6 x 8mm
Screw (51)–2
M8 Nylon
Locknut (37)–4
M10 x 73mm Button Screw (33)–4
M8 Split
Washer (36)–4
M10 Split
Washer (34)–7
Page 5
5
2. While another person lifts the rear of the Frame (1),
attach the Rear Stabilizer (14) to the Frame with two
M10 x 73mm Button Screws (33) and two M10 Split
Washers (34).
33
34
34
14
1
3
3
35
Be careful to avoid
pinching the Wire
Harnesses (31, 32)
34
34
1
35
3. While another person holds the Upright (3) near the
Frame (1), connect the Upper Wire Harness (32) to the
Lower Wire Harness (31).
Gently pull the upper end of the Upper Wire Harness
(32) to remove the slack, and slide the Upright (3) onto
the Frame (1). Be careful to avoid pinching the Wire
Harnesses. Attach the Upright with three M10 x 20mm
Button Screws (35) and three M10 Split Washers (34).
2
32
31
4. The Console (6) requires four “AA” batteries; alkaline
batteries are recommended. Press the tab on the battery cover and remove the battery cover. Insert four
batteries into the console; make sure that the batter-
ies are oriented as shown. Then, reattach the battery
cover.
Note: The Console (6) can be operated with an
optional power supply instead of batteries. To pur-
chase a power supply, call the telephone number
on the front cover of this manual. Plug one end of
the power supply into the jack on the console. Plug
the other end of the power supply into an appropriate
outlet that is properly installed in accordance with all
local codes and ordinances.
6
Batteries
Battery
Cover
4
Page 6
6
7. Orient the Handlebar (47) as shown. Attach the
Handlebar to the Upright (3) with the Upright Clamp
(45) and the Adjustment Handle (46). Note: The
Adjustment Handle works like a spanner. Turn the handle clockwise, push it toward the Handlebar, turn it
counterclockwise, pull it away from the Handlebar, and
then turn it clockwise again.
6. Attach the Water Bottle Holder (29) to the Upright (3)
with two M4 x 15mm Screws (15).
6
7
5
5. While another person holds the Console (6) near the
Upright (3), connect the console wire harness to the
Upper Wire Harness (32).
Insert the excess Upper Wire Harness (32) downward
into the Upright (3). Attach the Console (6) to the
Upright with four M4 x 15mm Screws (40).
Be careful
to avoid pinching the wires.
15
29
3
3
40
32
6
Console Wire
Harness
40
47
3
45
46
Be careful to avoid
pinching the wires
Page 7
7
11. Make sure that all parts are properly tightened before you use the exercise cycle. Note: After assembly is
completed, some extra parts may be left over. Place a mat beneath the exercise cycle to protect the floor.
8. Orient the Seat Post (5) as shown. Pull the Adjustment
Knob (11) outward and insert the Seat Post into the
Frame (1). Move the Seat Post upward or downward
to the desired position, and then release the
Adjustment Knob into one of the adjustment holes in
the Seat Post. Make sure that the Adjustment Knob
is engaged in an adjustment hole.
Attach an M6 x 8mm Screw (51) to the front of the
Seat Post (5).
9. Orient the Seat (12) and the Seat Carriage (26) as
shown. Attach the Seat to the Seat Carriage with
four M8 Nylon Locknuts (37) and four M8 Split
Washers (36). Note: The Nylon Locknuts and
Split Washers may be preattached to the underside of the Seat.
Slide the Seat Carriage (26) onto the Seat Post (5)
and move the Seat Carriage forward or backward to
the desired position. Then, tighten the Seat Knob
(52) into the Seat Carriage.
Attach an M6 x 8mm Screw (51) to the rear of the
Seat Post (5).
9
10. Identify the Left Pedal (24), which is marked with an
“L.” Using an adjustable wrench, firmly tighten the
Left Pedal
counterclockwise
into the Left Crank Arm
(42). Tighten the Right Pedal (not shown)
clockwise
into the Right Crank Arm (not shown). Important:
Tighten both Pedals as firmly as possible. After
using the exercise cycle for one week, retighten
the Pedals. For best performance, keep the
Pedals tightened.
Adjust the strap on the Left Pedal (24) to the
desired position, and press the end of the strap onto
the tab on the side of the Left Pedal. Adjust the
strap on the Right Pedal (not shown) in the same
way.
10
8
51
11
5
1
26
36
37
52
12
51
5
24
42
Strap
Ta b
Page 8
8
HOW TO OPERATE THE EXERCISE CYCLE
HOW TO ADJUST THE HEIGHT OF THE SEAT
For effective exercise, the seat
should be at the
proper height. As
you pedal, there
should be a slight
bend in your knees
when the pedals
are in the lowest
position.
To adjust the seat,
first turn the adjustment knob counterclockwise several
turns to loosen it.
Next, pull the knob, slide the seat post upward or
downward to the desired position, and then release
the knob. Move the seat post upward or downward
slightly to make sure that the knob is engaged in
one of the adjustment holes in the seat post. Then,
turn the knob clockwise to tighten it.
HOW TO ADJUST THE LATERAL POSITION OF
THE SEAT
To adjust the lateral
position of the seat,
first loosen the seat
knob a few turns.
Then, move the
seat forward or
backward to the
desired position,
and firmly tighten the seat knob.
HOW TO ADJUST THE HANDLEBAR
To adjust the handlebar, first turn the
indicated adjustment
handle counterclockwise to loosen
it. Note: The adjustment handle works
like a spanner. Turn
the handle counterclockwise, pull it
away from the handlebar, turn it clockwise, push it toward
the handlebar, and then turn it counterclockwise again.
Repeat until the handlebar is loose. Move the handlebar upward or downward to the desired position and
then retighten the handle.
HOW TO ADJUST THE PEDAL STRAPS
To adjust the pedal
straps, first pull the
ends of the pedal
straps off the tabs
on the pedals.
Adjust the pedal
straps to the
desired position,
and then press the
ends of the pedal
straps onto the tabs.
HOW TO LEVEL THE EXERCISE CYCLE
If the exercise cycle rocks slightly on your floor, turn
one or both of the leveling feet under the rear
stabilizer.
Pedal
Strap
Seat
Knob
Handle
Seat
Post
Adjustment
Knob
Seat
Seat
Page 9
9
FEATURES OF THE CONSOLE
The console offers a selection of features designed to
make your workouts more effective. When you use the
manual mode of the console, you can change the
resistance of the pedals with the touch of a button. As
you exercise, the console will provide continuous exercise feedback. You can even monitor your heart rate
using the handgrip pulse sensor.
The console features four smart programs that automatically change the resistance of the pedals and
prompt you to vary your pedaling pace while guiding
you through an effective workout.
To use the manual mode of the console, follow the
steps beginning on page 10. To use a smart program,
see page 12.
Before using the console, make sure that batteries are
installed (see assembly step 4 on page 5). If there is a
sheet of clear plastic on the display, remove the plastic.
CONSOLE DIAGRAM
Page 10
10
HOW TO USE THE MANUAL MODE
Turn on the console.
To turn on the console, press any button or begin
pedaling. The display will light and the console
will be ready for use.
Select the manual mode.
Each time you turn
on the console, the
manual mode will be
selected. If you have
selected a program,
reselect the manual
mode by pressing any of the Smart Programs buttons repeatedly until zeroes appear in the display.
Begin pedaling and change the resistance of
the pedals as desired.
As you pedal,
change the resistance of the pedals
by pressing the
Resistance + and –
buttons. There are
ten resistance levels. Note: After you press the
buttons, it will take a moment for the pedals to
reach the selected resistance level.
Follow your progress with the display.
The upper section of
the display will show
the elapsed time and
the distance, in miles
or kilometers, that
you have pedaled.
The display will change modes every few seconds. Note: When you select a smart program the
display will show the time remaining in the program instead of the elapsed time.
The second section
of the display will
show your pedaling
pace, in miles or kilometers per hour.
The third section of
the display will show
the approximate number of calories you
have burned and the
resistance level of the
pedals. The display will change modes every few
seconds. The display will also show your heart
rate when you use the handgrip pulse sensor.
The last section of the
display will show a
track representing 1/4
mile. As you exercise,
indicators will appear
in succession around
the track until the entire track appears. The track
will then disappear and the indicators will again
begin to appear in succession.
Note: The console
can show speed and
distance in either
miles of kilometers.
The letters MPH or
Km/H will appear in
the display to indicate which unit of measurement
is selected. To change the unit of measurement,
press and hold down the far right Smart Program
button for a few seconds. An “E” for English miles
or an “M” for metric kilometers will appear in the
display. Press the Resistance + button to select
the desired unit of measurement. Then, press the
far left Smart Program button to save your selection. Note: When you replace the batteries, it may
be necessary to reselect the unit of measurement.
4
3
2
1
Page 11
11
Measure your heart rate if desired.
If there are sheets
of clear plastic on
the metal contacts
on the handgrip
pulse sensor,
remove the plastic. Next, hold the
handgrip pulse sensor with your palms
resting on the metal
contacts. Avoid
moving your
hands or gripping the contacts too tightly.
When your pulse is detected, a heart-shaped
symbol will flash in the display each time your
heart beats and then your heart rate will be
shown. For the most accurate heart rate reading,
hold the contacts for at least 15 seconds.
When you are finished exercising, the console
will turn off automatically.
If the pedals do not move for a few seconds, the
time will begin to flash in the display and the console will pause. If the pedals do not move for a
few minutes and no buttons are pressed, the console will turn off and the display will be reset.
65
Contacts
Page 12
12
HOW TO USE A SMART PROGRAM
Turn on the console.
To turn on the console, press any button or begin
pedaling. The display will light and the console
will be ready for use.
Select a smart program.
To select a smart
program, press the
desired Smart
Programs button.
The upper section of
the display will show
how long the program will last.
Begin pedaling to start the program.
Each program is divided into 30 one-minute segments. One resistance level and one pace setting
are programmed for each segment. Note: The
same resistance level and/or pace setting may be
programmed for two or more consecutive segments.
Whenever the resistance is about to change, the
resistance level will flash in the display for a few
seconds. The resistance of the pedals will then
automatically change to the resistance level programmed for the next segment. Note: If the resistance level is too low or too high, you can override it by pressing the Resistance + and – buttons. Important: When the current segment of
the program ends, the pedals will automatically
adjust to the resistance level programmed for
the next segment.
As you exercise, the
display will prompt
you to keep your pedaling pace near the
pace setting for the
current segment.
When the word “faster” appears in the display,
increase your pace. When the word “slower”
appears, decrease your pace. When the center of
the target flashes, maintain your current pace.
Important: The pace settings are intended
only to provide motivation. Your actual pace
may be slower than the pace settings. Make
sure to pedal at a pace that is comfortable for
you.
If you stop pedaling for several seconds, the time
will begin to flash in the display. To restart the program, simply resume pedaling.
The program will continue until the display shows
a time of 0:00. If you continue to pedal after the
program is completed, the display will continue to
show exercise feedback; however, the display will
not show the elapsed time until you select the
manual mode or a new program.
Follow your progress with the display.
See step 4 on page 10.
Measure your heart rate if desired.
See step 5 on page 11.
When you are finished exercising, the console
will turn off automatically.
See step 6 on page 11.
6
5
4
3
2
1
Page 13
13
Inspect and properly tighten all parts of the exercise
cycle regularly. Replace any worn parts immediately.
To clean the exercise cycle, use a damp cloth and a
small amount of mild soap. Important: To avoid
damage to the console, keep liquids away from
the console and keep the console out of direct
sunlight.
PULSE SENSOR TROUBLESHOOTING
For optimal performance of the pulse sensor, keep the
metal contacts clean. Clean the contacts with a soft
cloth—never use alcohol, abrasives, or chemicals.
Avoid moving your hands while using the pulse sensor. Excessive movement may interfere with heart
rate readings. Do not hold the metal contacts too
tightly; doing so may interfere with heart rate readings. For the most accurate heart rate reading, hold
the metal contacts for about 15 seconds.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted. To adjust the reed
switch, the pedals and the side shields must be
removed.
Using an adjustable wrench, turn the left pedal clockwise and turn the right pedal counterclockwise to
remove the pedals.
Remove the screws from the left and right side
shields. Note: There are two different sizes of screws
in the side shields. Be sure to note the location of
each screw. Then, carefully remove the side shields.
Next, locate
the Reed
Switch (21).
Turn the Left
Crank Arm
(42) until the
Magnet (16) is
aligned with
the Reed
Switch.
Loosen, but
do not
remove, the
indicated M5 x 12mm Screw (53). Slide the Reed
Switch slightly closer to or away from the Magnet, and
then retighten the Screw. Turn the Crank Arm for a
moment. Repeat until the console displays correct
feedback.
When the Reed Switch is correctly adjusted, reattach
the side shields and the pedals. To reattach the pedals, turn the left pedal counterclockwise and turn the
right pedal clockwise.
BATTERY REPLACEMENT
If the console display becomes dim, the batteries
should be replaced; most console problems are the
result of low batteries. To replace the batteries, see
assembly step 4 on page 5.
HOW TO LEVEL THE EXERCISE CYCLE
If the exercise cycle rocks slightly on your floor, turn
one or both of the leveling feet under the rear
stabilizer.
MAINTENANCE AND TROUBLESHOOTING
42
16
53
21
Page 14
14
CONDITIONING GUIDELINES
The following guidelines will help you to plan your
exercise program. Remember that proper nutrition
and adequate rest are essential for successful results.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning, maximum fat
burning, and cardiovascular (aerobic) exercise.
To find the proper heart rate for you, first find your age
at the bottom of the chart (ages are rounded off to the
nearest ten years). Next, find the three numbers above
your age. The three numbers are your “training zone.”
The lowest number is the recommended heart rate for
fat burning; the middle number is the recommended
heart rate for maximum fat burning; the highest number is the recommended heart rate for aerobic exercise.
Fat Burning
To burn fat effectively, you must exercise at a relatively low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible
carbohydrate
calories for energy. Only after the first few minutes of exercise does
your body begin to use stored
fat
calories for energy.
If your goal is to burn fat, adjust the intensity of your
exercise until your heart rate is near the lowest number in your training zone as you exercise. For maximum fat burning, adjust the intensity of your exercise
until your heart rate is near the middle number in your
training zone as you exercise.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise is activity that requires large amounts of oxygen
for prolonged periods of time. This increases the
demand on the heart to pump blood to the muscles,
and on the lungs to oxygenate the blood. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A warm-up, consisting of 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases your
body temperature, heart rate, and circulation in preparation for exercise.
Training zone exercise, consisting of 20 to 30 minutes of exercising with your heart rate in your training
zone. Note: During the first few weeks of your exercise program, do not keep your heart rate in your
training zone for longer than 20 minutes.
A cool-down, with 5 to 10 minutes of stretching. This
will increase the flexibility of your muscles and will
help to prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, plan three workouts each week, with at least one day of rest between
workouts. After a few months of regular exercise, you
may complete up to five workouts each week, if
desired. Remember, the key to success is make exercise a regular and enjoyable part of your everyday life.
WARNING:
• Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of
35 or persons with pre-existing health
problems.
• The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determining heart rate trends in general.
Page 15
15
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the
right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward
from your hips. Allow your back and shoulders to relax as you
reach down toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Hamstrings, back
of knees and back.
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for each leg. Stretches:
Hamstrings, lower back and groin.
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat
3 times for each leg. To cause further stretching of the achilles
tendons, bend your back leg as well. Stretches: Calves, achilles
tendons and ankles.
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. Repeat 3
times for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps
and hip muscles.
1
2
3
4
5
Page 16
16
NOTES
Page 17
17
NOTES
Page 18
18
PART LIST—Model No. PFEVEX2416.0 R0107A
1 1 Frame
2 1 Front Stabilizer
3 1 Upright
4 2 Endcap
5 1 Seat Post
6 1 Console
7 1 Eddy Mechanism
8 1 Resistance Motor
9 1 Crank
10 1 Resistance Cable
11 1 Adjustment Knob
12 1 Seat
13 2 Foot
14 1 Rear Stabilizer
15 2 M4 x 15mm Screw
16 1 Magnet
17 1 Left Side Shield
18 1 Right Side Shield
19 1 Spring
20 1 Seat Post Bushing
21 1 Reed Switch/Wire
22 1 Clamp
23 1 Belt
24 1 Left Pedal/Strap
25 1 Right Pedal/Strap
26 1 Seat Carriage
27 2 Crank Bearing Set
28 1 Idler
29 1 Water Bottle Holder
30 2 Idler Pulley
31 1 Lower Wire Harness
32 1 Upper Wire Harness
33 4 M10 x 73mm Button Screw
34 7 M10 Split Washer
35 3 M10 x 20mm Button Screw
36 4 M8 Split Washer
37 7 M8 Nylon Locknut
38 2 M6 Nut
39 3 M4 x 25mm Screw
40 4 M4 x 15mm Screw
41 8 M5 x 20mm Screw
42 1 Left Crank Arm
43 1 Right Crank Arm
44 2 Crank Cover
45 1 Upright Clamp
46 1 Adjustment Handle
47 1 Handlebar
48 2 Handlebar Endcap
49 2 Wheel
50 2 Hub Cap
51 2 M6 x 8mm Screw
52 1 Seat Knob
53 5 M5 x 12mm Screw
54 2 M8 x 25mm Flange Screw
55 1 M8 x 20mm Bolt
56 2 Snap Ring
57 2 Eye Bolt
58 2 3/8" Nut
59 2 Flywheel Nut
60 1 M8 Washer
61 1 Pulley
62 4 M6 x 16mm Screw
63 4 M6 Nylon Jamnut
64 2 Foam Grip
# 1 Assembly Tool
# 1 User’s Manual
# 2 Hex Key
Key No. Qty. Description Key No. Qty. Description
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts.
Page 19
19
EXPLODED DRAWING—Model No. PFEVEX2416.0 R0107A
50
44
24
49
54
15
42
35
29
2
48
56
40
34
27
47
34
41
12
52
59
9
57
4
18
41
39
41
25
62
58
38
7
44
54
43
62
23
30
41
64
41
51
37
28
63
55
53
16
39
26
36
19
59
8
14
17
36
37
61
53
13
41
39
6
45
20
30
5
11
56
27
60
38
4
3
46
32
34
35
31
53
22
21
1
50
57
58
37
49
10
34
37
33
13
34
33
Page 20
Part No. 246497 R0107A Printed in China © 2007 ICON IP, Inc.
PROFORM is a registered trademark of ICON IP, Inc.
ORDERING REPLACEMENT PARTS
To order replacement parts, contact the ICON Health & Fitness, Ltd. office, or write:
ICON Health & Fitness, Ltd.
Customer Service Department
Unit 4, Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
Te l:
Outside the UK: 0 (044) 113 387 7133
Fax: 0 (044) 113 387 7125
To help us assist you, please be prepared to give the following information:
• the MODEL NUMBER of the product (PFEVEX2416.0)
• the NAME of the product (PROFORM 710 EKG exercise cycle)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see pages 18 and 19)
08457 089 009
Loading...