Page 1
USER'S MANUAL
¨
Serial
Number
Decal
Model No. PFTL58581
Serial No.
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satisfaction through direct assistance
from our factory.
TO AVOID UNNECESSARY DELAYS, PLEASE CALL DIRECT TO
OUR TOLL-FREE CUSTOMER
HOT LINE. The trained technicians on our Customer Hot Line
will provide immediate assistance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
VISIT OUR WEBSITE:
www.proformfitness.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Page 2
2
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
MAINTENANCE AND TROUBLE-SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING and PART LIST are attached to the center of this manual. Please save them for
future reference.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
2. Use the treadmill only as described in this
manual.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it. Do not
place the treadmill on any surface that blocks
air openings. To protect the floor or carpet
from damage, place a mat under the treadmill.
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should not be used by persons
weighing more than 250 pounds.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothing when
using the treadmill. Do not wear loose clothing that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
10. When connecting the power cord (see page 7),
plug the power cord into a surge protector
(not included) and plug the surge protector
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be
on the same circuit. Do not use an extension
cord.
11. Use only a UL-listed surge protector, rated at
15 amps, with a 14-gauge cord of five feet or
less in length. Do not use an extension cord.
12. Keep the power cord and the surge protector
away from heated surfaces.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 4 if the treadmill is not working properly.)
WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
IMPORTANT PRECAUTIONS
Page 3
3
14. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
16. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
17. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord and move the on/off switch to
the off position when the treadmill is not in
use. (See the drawing on page 4 for the location of the on/off switch.)
18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 5, and HOW TO MOVE
THE TREADMILL on page 10.) You must be
able to safely lift 45 pounds (20 kg) in order to
raise, lower, or move the treadmill.
19. Do not change the incline of the treadmill by
placing objects under the treadmill.
20. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
21. Inspect and tighten all parts of the treadmill
regularly.
22. Never drop or insert any object into any
opening.
23. DANGER: Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the maintenance and adjustment procedures described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
24. This treadmill is intended for in-home use
only. Do not use this treadmill in any commercial, rental, or institutional setting.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown have been
placed on your treadmill. If a decal
is missing, or if it is not legible,
please call our Customer Service
Department, toll-free, to order a free
replacement decal (see ORDERING
REPLACEMENT PARTS on the
back cover of this manual). Apply
the decal in the location shown.
Page 4
4
Thank you for selecting the PROFORM¨585EX treadmill. The 585EX treadmill combines advanced technology with innovative design to let you enjoy an excellent
form of cardiovascular exercise in the convenience and
privacy of your home. And when youÕre not exercising,
the unique 585EX can be folded up, requiring less than
half the floor space of other treadmills.
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
please call our Customer Service Department toll-free
at 1-800-999-3756, Monday through Friday, 6 a.m.
until 6 p.m. Mountain Time (excluding holidays). To
help us assist you, please note the product model
number and serial number before calling. The model
number of the treadmill is PFTL58581. The serial number can be found on a decal attached to the treadmill
(see the front cover of this manual for the location).
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
BEFORE YOU BEGIN
Handrail
Handrail
Console
Storage Latch
Book Holder
Key/Clip
Circuit
Breaker
Walking Belt
Front
Wheel
Foot Rails
Power Cord
Rear Roller
Adjustment Bolts
Water Bottle
Holder (Bottle
not included)
Accessory Tray
RIGHT SIDELEFT SIDE
On/Off Switch
Page 5
5
1. With the help of a second person, carefully raise the
treadmill to the upright position.
While the other person tips the treadmill to one side and
holds it, insert an Extension Leg (59) into one side of
the Base (32). Make sure that the Extension Leg is
turned so the bracket is on the side shown. Using the
Allen Wrench (102), tighten an Extension Leg Screw
(57) into the Extension Leg and the Base. Attach the
other Extension Leg in the same manner.
2. Refer to HOW TO LOWER THE TREADMILL FOR
USE on page 11. Follow the instructions in step 2 to
lower the treadmill.
Cut the plastic ties holding the cage nuts in the upper
end of each Handrail (60, 62).
Position the Left Handrail (60) on the left Upright (32) as
shown. The bracket on the Extension Leg (59) should
be inside of the lower end of the Left Handrail (see the
inset drawing). Thread two Handrail Bolts (30) with
Handrail Washers (31) into the left Upright and the Left
Handrail. Do not tighten the Handrail Bolts yet.
While another person holds the Console Base (46), attach the Right Handrail (62) in the same way. Be care-
ful to avoid damaging the Wire Harness (35).
57
102
59
32
Bracket
60
46
30
30
30
31
32
59
35
62
30
31
1
2
ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench
and your own phillips screwdriver , adjustable wrench , and scissors .
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
59
Page 6
7. Make sure that all parts are tightened before you use the treadmill. To protect the floor or carpet, place a
mat under the treadmill.
6
28
33
32
34
4
62
59
59
28
28
60
5
102
101
32
4. Attach the Storage Latch (34) and the two Latch
Spacers (33) to the left Upright (32) with two Screws
(28). Be careful not to overtighten the Screws.
Note: If it is difficult to fold or lower the treadmill, remove one or both of the Latch Spacers (33).
Fold the treadmill to the storage position (see HOW TO
FOLD THE TREADMILL FOR STORAGE on page 10).
5. Attach the lower end of the Right Handrail (62) to the
right Extension Leg (59) with a Screw (28).
Attach the lower end of the Left Handrail (60) in the
same way.
Tighten all parts used in this step and in step 2.
6. Remove the backing from the Adhesive Clip (101).
Press the Adhesive Clip onto the base of the right
Upright (32) as shown. Press the Allen Wrench (102)
into the Adhesive Clip.
6
3. Set the Console Base (46) on the Handrails (60, 62).
Route the Wire Harness (35) under the Console Base
as shown and then press the Wire Harness up into the
Console Base. Insert any slack into the Right Handrail
(62).
Attach the Console Base (46) to the Handrails (60, 62)
with the four longer 1 1/4Ó Screws.
35
62
60
46
1 1/4Ó Screw
1 1/4Ó
Screw
3
Page 7
7
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETMWALKING BELT
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking platform. They will deteriorate the walking belt and
cause excessive wear.
HOW TO PLUG IN THE POWER CORD
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your homeÕs power.
Voltage surges, spikes, and noise interference can result from weather conditions or from other appliances
being turned on or off.
To decrease the possibility of your treadmill being damaged,
always use a surge
protector (not included) with your
treadmill.
Surge protectors are
sold at most hardware
stores and department
stores. Use only a ULlisted surge protector,
rated at 15 amps, with a
14-gauge cord of five
feet or less in length.
This product must be
grounded. If it should
malfunction or break
down, grounding provides a path of least resistance for electric current to reduce the risk of
electric shock. This product is equipped with a cord
having an equipment-grounding conductor and a
grounding plug. Plug the power cord into a surge
protector, and plug the surge protector into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge protector to a 2-pole receptacle as shown in drawing 2 if a properly grounded outlet is not available.
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
DANGER: Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the productÑif it will
not fit the outlet, have a proper outlet installed by a qualified electrician.
1
2
Grounded Outlet Box
Grounded Outlet Box
Grounding Plug
Treadmill Power Cord
Grounding Plug
Grounding Plug
Grounding Pin
Surge Protector
Grounding Pin
Grounding Pin
Adapter
Lug
Metal Screw
Grounded Outlet
Page 8
DIAGRAM OF THE CONSOLE
Pulse Sensor Speed Control
Incline Control
Clip
Key
Monitor Displays
LED Track
STEP-BY-STEP CONSOLE OPERATION
If there is a thin sheet of clear plastic on the face of the
console, remove it. Next, make sure that the power
cord is properly plugged
in (see HOW TO PLUG
IN THE POWER CORD
on page 7). Be sure that
the on/off switch near
the power cord is in the
on position.
Stand on the foot rails of the treadmill. Find the clip
attached to the key (see the drawing above), and
slide the clip onto the waistband of your clothing.
Follow the steps below to operate the console.
Insert the key fully into the power switch.
After a moment, the
four displays and one
indicator in the LED
track will light.
Reset the speed control.
Slide the speed
control to the
the RESET
position. Note:
Each time the
walking belt is
stopped, the
speed control must be moved to the RESET
position before the walking belt can be restarted.
Start the walking belt.
Slowly slide the speed control to the right until the
walking belt begins to move at slow speed. Step
onto the walking belt and begin exercising. Change
the speed of the walking belt as desired by sliding
the speed control.
To stop the walking belt, step onto the foot rails
and slide the speed control to the RESET position. After a few seconds, the displays will pause.
3
2
1
On
Position
CAUTION: Before operating the
console, read the following precautions.
¥ Do not stand on the walking belt when turn-
ing on the power.
¥ Always wear the clip (see the drawing
above) while using the treadmill.
¥ Adjust the speed in small increments.
¥ The settings marked above the speed con-
trol (warm-up, fat burn, aerobic and performance) are general guidelines only. See
page 14 for more information.
¥ To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and use only a sealable
water bottle.
8
Page 9
9
Follow your progress with the LED track and
the four displays.
The LED
TrackÑThe LED
track represents
a distance of 1/4
mile. As you exercise, the indicators around the
track will light one
at a time until you have completed 1/4 mile. A new
lap will then begin.
DISTANCE/LAPS
displayÑThis display
shows the distance that
you have walked and
the number of laps you
have completed. The
display will change from one number to the other
every seven seconds. An ÒLÓ will appear in the display when the number of laps is shown. Note: If the
KPH indicator beside the SPEED display is lit, the
distance will be displayed in kilometers; if the indicator is not lit, the distance will be displayed in miles.
SPEED displayÑThis
display shows the speed
of the walking belt, in
miles per hour or kilometers per hour. If the KPH
indicator is lit, the speed
will be displayed in kilometers per hour. Note: To
change the unit of measurement, hold down the
DISPLAY RESET button for about seven seconds.
CALS/FAT CALS/
PULSE displayÑThis
display shows the approximate numbers of
calories and fat calories you have burned.
(See BURNING FAT on page 14 for an explanation
of fat calories.) Every seven seconds, the display
will change from one number to the other. The FAT
indicator will light when the number of fat calories is
shown. Note: This display also shows your pulse
when the pulse sensor is used.
TIME displayÑThis
display shows the total
time that you have
walked since the display
was reset.
Note: If the walking belt is stopped and no
console buttons are pressed for five minutes,
the displays will automatically turn off. To light
the displays, press the DISPLAY RESET button.
To reset the displays,
press the DISPLAY
RESET button. The displays will darken for a
moment and then light.
Measure your pulse, if desired.
Stand on the foot rails and place your thumb on the
pulse sensor as shown. The pulse sensor is pressure-activatedÑfully press it down. (Do not press
too hard, or the
circulation in
your thumb will
be restricted,
and your pulse
will not be detected.) Next,
raise your thumb
slightly until the
heart-shaped
indicator by the
CALS/FAT CALS/
PULSE display
flashes steadily.
Hold your thumb at this level. After a few seconds,
three dashes will appear in the display and your
pulse will be shown. Hold your thumb on the sensor
for another 15 seconds for the most accurate reading. If the displayed pulse appears to be too high or
too low, or if your pulse is not displayed, lift your
thumb off the sensor and allow the display to reset.
Press down again on the sensor as described above.
Make sure that your thumb is positioned as shown,
and that you are applying the proper amount of pressure to the pulse sensor. Try the sensor several
times until you become familiar with it. Remember to
stand still while measuring your pulse.
Change the incline of the treadmill, if desired.
To change the incline, hold down
the top or bottom of the incline control until the desired incline level is
reached.
When you are finished exercising, stop the
walking belt and remove the key.
Step onto the foot rails, stop the walking belt, and
remove the key from the console. Store the key in a
secure place.
7
6
5
4
Pulse Sensor
Indicator
Page 10
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
permanently damaged. Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20
kg) in order to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. Caution: To decrease the possibility of in-
jury, bend your legs and keep your back straight. As
you raise the treadmill, make sure to lift with your legs
rather than your back. Raise the treadmill about halfway
to the vertical position.
2. Move your right hand to the position shown and
hold the treadmill firmly. Using your left thumb,
press the storage latch to the left as you raise the
treadmill to the storage position. Make sure that
the storage latch is fully engaged over the
catch.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85¡ Fahrenheit.
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the stor-
age latch is closed fully over the catch.
1. Hold the handrails as shown and place one foot against a
wheel. Do not hold or push on the book holder or the
book holder may be damaged.
2. Tilt the treadmill back until it rolls freely on the front wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
3. Place one foot on the base, and carefully lower the tread-
mill until it is resting in the storage position.
10
Book Holder
Base
Front Wheels
Catch
Storage
Latch
Closed
Page 11
11
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand as
shown. Using your left thumb, press the storage latch and
hold it. Pivot the treadmill until the frame is past the storage latch.
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. Caution: To decrease the possibil-
ity of injury, bend your legs and keep your back
straight.
Opened
Storage
Latch
Page 12
12
MAINTENANCE AND TROUBLE-SHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department tollfree at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge protector, and that the surge protector is
plugged into a properly grounded outlet. (See HOW TO PLUG IN THE POWER CORD on page
7.) Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or
less in length.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the con-
sole. (See step 1 on page 8.)
c. Check the circuit breaker located on the treadmill
near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
d. Check the on/off switch located at the front of the
treadmill near the power cord. The switch must be
in the on position.
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If
the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console. (See step 1 on page 8.)
d. Make sure that the on/off switch is in the on position. (See 1. d. above.)
e. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. Next, remove the screws from the
hood and carefully remove the hood. Locate the Reed
Switch (97) and the Magnet (9) on the left side of the
Pulley (10). Turn the Pulley until the Magnet is aligned
with the Reed Switch. Check the gap between the
Magnet and the Reed SwitchÑit should be about
1/8Ó. If necessary, loosen the Screw (98) and move
the Reed Switch slightly. Retighten the Screw.
Reattach the hood and run the treadmill for a few minutes to check for a correct speed reading.
97
98
Top
View
1/8Ó
9
10
Tripped
c
Reset
On
Position
d
Page 13
13
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less in
length.
b. If the walking belt is overtightened, treadmill perfor-
mance may decrease and the walking belt may be
permanently damaged. Remove the key and UN-
PLUG THE POWER CORD. Using the allen wrench,
turn both rear roller adjustment bolts counterclockwise, 1/4 of a turn. When the walking belt is properly
tightened, you should be able to lift each side of the
walking belt 2 to 3 inches off the walking platform. Be
careful to keep the walking belt centered. Plug in the
power cord, insert the key and run the treadmill for a
few minutes. Repeat until the walking belt is properly
tightened.
c. If the walking belt still slows when walked on, please call our Customer Service Department, toll-
free.
PROBLEM: The walking belt is off-center when walked on
SOLUTION: a. If the walking belt has shifted to the left, first remove
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn the left rear roller adjustment
bolt clockwise, and the right bolt counterclockwise,
1/4 of a turn each. Be careful not to overtighten the
walking belt. Plug in the power cord, insert the key
and run the treadmill for a few minutes. Repeat until
the walking belt is centered.
b. If the walking belt has shifted to the right, first remove
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn the left rear roller adjustment
bolt counterclockwise, and the right bolt clockwise,
1/4 of a turn each. Be careful not to overtighten the
walking belt. Plug in the power cord, insert the key
and run the treadmill for a few minutes. Repeat until
the walking belt is centered.
PROBLEM: The walking belt slips when walked on
SOLUTION: a. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn both rear roller adjustment
bolts clockwise, 1/4 of a turn. When the walking belt
is correctly tightened, you should be able to lift each
side of the walking belt 2 to 3 inches off the walking
platform. Be careful to keep the walking belt centered.
Plug in the power cord, insert the key and carefully
walk on the treadmill for a few minutes. Repeat until
the walking belt is properly tightened.
Rear Roller Adjustment Bolts
2ÓÐ3Ó
b
b
a
a
Page 14
14
CONDITIONING GUIDELINES
The following guidelines will help you to plan your exercise program. RememberÑthese are general guidelines only. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the desired
results is to exercise with the proper intensity. The
proper intensity level can be found by using your heart
rate as a guide. The chart below shows recommended
heart rates for fat burning and aerobic exercise.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your Òtraining zone.Ó The lowest number is the recommended
heart rate for fat burning; the middle number is the recommended heart rate for aerobic exercise; and the
highest number is for advanced conditioning.
To measure your heart rate during exercise, use the
pulse sensor on the console. If your heart rate is too
high or too low, adjust the speed and incline of the
treadmill.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time. During
the first few minutes of exercise, your body uses easily
accessible carbohydrate calories for energy. Only after
the first few minutes does your body begin to use
stored fat calories for energy. If your goal is to burn fat,
adjust the speed and incline of the treadmill until your
heart rate is near the lowest number in your training
zone. It may also be helpful to set the speed control on
the console to FAT BURN.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be Òaerobic.Ó Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the middle of your training zone. It
may also be helpful to set the speed control on the
console to AEROBIC.
High Performance Athletic Conditioning
If your goal is high performance athletic conditioning,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone, or set the speed control on the console to PERFORMANCE. Note: During the first few weeks of your
exercise program, keep your heart rate near the low end
of your training zone.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-upÑStart each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate, and circulation in preparation for exercise.
Training Zone ExerciseÑAfter warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exerciseÑnever
hold your breath.
WARNING: Before beginning this
or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
Page 15
15
SUGGESTED STRETCHES
The correct form for several basic stretches is shown in the
drawings at the right. Move slowly as you stretchÑnever
bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward
from your hips. Allow your back and shoulders to relax as you
reach down toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Hamstrings,
back of knees and back.
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for both legs. Stretches:
Hamstrings, lower back and groin.
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your
back foot flat on the floor. Bend your front leg, lean forward and
move your hips toward the wall. Hold for 15 counts, then relax.
Repeat 3 times for both legs. To cause further stretching of the
achilles tendons, bend your back leg as well. Stretches:
Calves, achilles tendons and ankles.
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and
grasp one foot with your other hand. Bring your heel as close
to your buttocks as possible. Hold for 15 counts, then relax.
Repeat 3 times for both legs. Stretches: Quadriceps and hip
muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold
for 15 counts, then relax. Repeat 3 times. Stretches:
Quadriceps and hip muscles.
1
2
3
4
5
A Cool-downÑFinish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-exercise problems.
Exercise Frequency
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
Page 16
PART LISTÑModel No. PFTL58581 R0399A
Key No. Qty. Description
1 1 Frame
2 1 Catch Screw
3 1 Latch Catch
4 1 Rear Roller
5 2 Roller Guard
6 6 Platform Screw
7 2 Foot Rail
8 1 Walking Platform
9 1 Magnet
10 1 Front Roller/Pulley
11 1 Walking Belt
12 2 Rear Isolator
13 2 Rear Isolator Bolt
14 1 Latch Warning Decal
15 11 Belly Pan Screw
16 1 Belly Pan
17 4 Isolator
18 2 Frame Pivot Bolt
19 6 Hood Screw/Bracket Screw
20 1 Hood
21 1 Key/Clip
22 1 Book Rack
23 2 Battery Cover
24 0 Not Used
25 1 Incline Control
26 1 Speed Control
27 1 Speed Potentiometer
28 14 Screw
29 2 Rear Platform Screw
30 4 Handrail Bolt
31 4 Handrail Washer
32 1 Upright/Base
33 2 Latch Spacer
34 1 Latch
35 1 Wire Harness
36 2 Grommet
37 1 Incline Motor Nut
38 4 Cage Nut
39 2 Incline Leg Pivot Bolt
40 3 Adj. Washer
41 2 Incline Leg Pivot Nut
42 1 Incline Cover Shield
43 2 Belly Pan Side Screw
44 2 Incline Motor Spacer
45 1 Incline Motor
46 1 Console Base
47 1 Incline Stop Bracket
48 1 Incline Bolt
49 1 Shock
50 1 Incline Cover
51 1 Cotter Pin
52 1 Clevis Pin
53 2 Wheel Bolt
54 4 Base Pad Screw
55 4 Base Pad
56 2 Frame Spacer
57 2 Extension Leg Screw
58 4 Isolator Nut
Key No. Qty. Description
59 2 Extension Leg
60 1 Left Handrail
61 2 Extension Leg Endcap
62 1 Right Handrail
63 1 Rear Endcap
64* 1 Console Assembly
65 2 Front Wheel
66 1 Motor/Pulley/Flywheel/Fan
67 1 Motor Pivot Bolt
68 1 Motor Tension Nut
69 1 Motor Star Washer
70 1 Motor Tension Washer
71 1 Motor Tension Bolt
72 1 Motor Belt
73 1 Pulley/Flywheel/Fan
74 1 Motor
75 5 8Ó Wire Tie
76 2 Belt Guide
77 1 Endcap Foot (left)
78 16 Small Screw
79 2 Rear Roller Adj. Bolt
80 5 Hood Anchor
81 1 Circuit Breaker
82 1 Power Cord
83 1 Power Cord Grommet
84 1 On/off Switch
85 1 Outlet Bracket
86 5 Hood Bracket
87 2 Spacer
88 1 Power Supply
89 1 Electronics Bracket
90 2 Front Roller Nut
91 1 Controller
92 1 Front Roller Adj. Bolt
93 1 Incline Leg
94 1 Choke Plate
95 1 Choke
96 1 Clip
97 1 Reed Switch
98 6 Belly Pan Fastener/Clip Screw
99 1 Front Belly Pan
100 1 Ground Wire
101 1 Adhesive Clip
102 1 Allen Wrench
103 1 Endcap Plug
104 6 Endcap Fastener
105 1 Endcap Foot (Right)
106 4 Endcap Bolt
# 1 8Ó White Wire, Pig Tail
# 1 6Ó White Wire, 2 Male/1 Female
# 1 8Ó Blue Wire, Pig Tail
# 1 6Ó Blue Wire, 2 Male/1 Female
# 1 4Ó Black Wire, 2 Female
# 1 UserÕs Manual
* Includes all parts shown in the box
# These parts are not illustrated
Page 17
28
37
48
45
40
39
40
39
52
51
57
65
41
53
32
59
61
49
59
57
61
67
74
68
69
70
71
72
198086
19
80
86
87
78
89
91
78
87
93
86
19
85
78
95
78
19
80
86
37
19
80
86
98
98
99
98
104
104
104
104
104
103
106
40
63
106
79
7
10
4
6
6
8
7
18
76
78
15
15
15
15
17
12
12
16
1
81
15
35
35
15
80
40
36
41
41
9
102
101
96
43
97
83
82
11
66*
73
75
78
100
14
24
24
105
77
98
42
50
78
78
94
56
15
15
15
44
44
5
34
28
28
17
88
30
28
31
28
38
31
30
28
31
30
30
31
26
27
25
62
64*
46
22
60
90
92
40
13
13
29
58
58
33
79
43
43
3
2
78
78
78
20
21
23
84
47
90
5
315554
31
55
54
31
55
54
23
28
EXPLODED DRAWINGÑModel No. PFTL58581 R0399A
Page 18
Part No. 149299 H03031-C R0399A Printed in USA © 1998 ICON Health & Fitness, Inc.
ORDERING REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). When ordering parts, please be prepared to give
the following information:
¥ The MODEL NUMBER OF THE PRODUCT (PFTL58581).
¥ The NAME OF THE PRODUCT (PROFORM¨585EX treadmill).
¥ The SERIAL NUMBER OF THE PRODUCT (see the front cover of this manual).
¥ The KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the EXPLODED DRAWING and PART LIST
attached to the center of this manual).
If possible, place the treadmill near your telephone for easy reference when calling.
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product at one of its authorized service centers. All
products for which warranty claim is made must be received by ICON at one of its authorized service
centers with all freight and other transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-authorized by ICON. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal
usage or repairs not provided by an ICON authorized service center, to products used for commercial or
rental purposes, or to products used as store display models. No other warranty beyond that specifically
set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly,
the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Loading...