Pro-face PS-2000B Series User Manual

Page 1

Built-in Computer

PS-2000B Series

User Manual

When printing out this PDF manual, since the printer setting can effect the quality of the printout, be sure your printer’s quality setting is set to “High”.

Page 2

Preface

Thank you for purchasing Pro-face's PS-2000B Series Built-in Computer, hereafter referred to as the "PS-B" or "PS-B unit". This unit, which utilizes Pro-face's newest PC architecture, is equipped with a wide range of standard-equipment interfaces and is designed for use in a wide variety of industrial applications.

Prior to using the PS-B unit, be sure to read this manual thoroughly to familiarize yourself with the unit's operation procedures and functions.

< Note >

1. It is forbidden to copy the contents of this manual in whole, or in part, without the permission of the Digital Electronics Corporation.

2. The information in this manual is subject to change without notice.

3. This manual was written with care; however, if you should find any errors or omissions, please contact Pro-face and inform them of your findings.

4. Please be aware that Digital Electronics Corporation shall not be held liable by the user for any damages, losses, or third party claims arising from the uses of this product.

Product names used in this manual are the trademarks of their respective manufacturers.

Page 3

Preface

PREFACE................................................................................................................... 1

ESSENTIAL SAFETY PRECAUTIONS ................................................................ 5

DOCUMENT ATION CONVENTIONS................................................................. 8

PACKAGE CONTENTS .......................................................................................... 9

UL/C-UL (CSA) APPLICA TION NOTES............................................................ 10

CE MARKING NOTES ......................................................................................... 11

CHAPTER 1 PS-B UNIT BASICS

1.1 Prior to Operating the PS-B Unit ................................................................1-1

1.2 PS-B System Design..................................................................................... 1-3

1.3 PS-B Part Names and Features .................................................................. 1-5

1.4 Interfaces...................................................................................................... 1-7

1.4.1 RS-232C Interface (COM1/COM2/COM3/COM4).........................1-7

1.4.2 RAS Interface (RAS) ..........................................................................1-8

1.4.3 DVI-D Interface ................................................................................1-10

1.5 PS-B External Views and Dimensions...................................................... 1-11

1.5.1 PS-B Unit..........................................................................................1-11

1.5. 2 With CD-ROM/FDD Unit Attached .................................................1-12

1.5.3 With RS-232C/RS-485 Conversion Unit Attached ..........................1-13

1.5.4 With Mounting Bracket Attached ......................................................1-14

CHAPTER 2 HARDWARE INSTALLATION

2.1 Installing Optional Units and Expansion Boards ......................................2-1

2.2 Installing the PS-B Unit................................................................................ 2-6

2.2.1 PS-B Unit Installation Cautions...........................................................2-6

2.2.2 Installation Procedures .......................................................................2-8

2.3 Wiring ........................................................................................................... 2-10

2.3.1 Connecting the Power Cord .............................................................2-10

2.3.2 Power Supply Precautions.................................................................2-12

2.3.3 Grounding Precautions .....................................................................2-13

2.3.4 Precautions When Connecting I/O Signal Lines ................................2-14

PS-2000B Series User Manual

Page 4

CHAPTER 3 SYSTEM SETUP

3.1 Setup Procedures .......................................................................................... 3-1

3.2 System Parameters.......................................................................................3-2

3.2.1 Standard CMOS Features ..................................................................3-2

3.2.2 IDE HDD Auto-Detection...................................................................3-4

3.2.3 Advanced BIOS Features ...................................................................3-5

3.2.4 Advanced Chipset Features ................................................................3-8

3.2.5 Integrated Peripherals........................................................................3-10

3.2.6 Power Management Setup ................................................................3-13

3.2.7 PnP/PCI Configurations ....................................................................3-15

3.2.8 IRQ Resources..................................................................................3-16

3.2.9 DMA Resources................................................................................3-17

3.2.10 System Monitor Setup .......................................................................3-18

3.2.11 Frequency/Voltage Control................................................................3-20

Preface

3.2.12 Load Fail-Safe Defaults.....................................................................3-21

3.2.13 Load Optimized Defaults ...................................................................3-21

3.2.14 Set Supervisor Password ..................................................................3-21

3.2.15 Set User Password............................................................................3-22

3.2.16 Save & Exit Setup .............................................................................3-22

3.2.17 Exit Without Saving ...........................................................................3-22

CHAPTER 4 SETTING UP YOUR PS-B UNIT

4.1 CD-ROM Contents.......................................................................................4-1

4.1.1 Software ..............................................................................................4-1

4.2 Setting up Your PS-B Unit............................................................................ 4-2

4.2.1 Setup Procedures ................................................................................4-2

4.2.2 Setting Up an HDD with Pre-installed OS ..........................................4-4

4.3 Installing Drivers ..........................................................................................4-6

4.4 Special Application Program Features .......................................................4-7

4.4.1 Uninstalling Utility Software.................................................................4-8

4.5 When Using Windows®2000/Windows®XP .................................................4-8

4.5.1 Automatic System Log-on Setup.........................................................4-8

4.5.2 Uninterrupted Power Supply System (UPS) .......................................4-9

4.5.3 Changing System Settings....................................................................4-9

4.5.4 NTFS File System Conversion..........................................................4-10

PS-2000B Series User Manual

Page 5

Preface

CHAPTER 5 MONITORING FEATURES

5.1 RAS Features................................................................................................ 5-1

5.1.1 PS-B RAS Features............................................................................5-1

5.1.2 RAS Feature Details............................................................................5-2

5.1.3 RAS Feature Overview .......................................................................5-5

5.2 System Monitor/RAS Features...................................................................5-6

5.2.1 Setup Procedures ................................................................................5-6

5.2.2 System Monitoring Property Settings (PSB_Wps.exe) .......................5-7

5.2.3 System Monitoring Operation (PSB_Smon.exe).................................5-8

5.2.4 Error Messages .................................................................................5-10

5.2.5 Error Displays When Using Event Viewer......................................... 5-11

5.3 Remote RAS................................................................................................5-13

5.3.1 System Configuration........................................................................5-13

5.3.2 Installation Procedures ......................................................................5-13

5.3.3 Setup and Preparation of the Remote RAS Feature..........................5-14

5.3.4 Read and Write of the System Monitor/RAS Feature.......................5-15

5.3.5 Restrictions........................................................................................5-18

5.4 Remote Shutdown Feature......................................................................... 5-19

CHAPTER 6 MAINTENANCE AND INSPECTION

6.1 Cleaning the Fan Filter................................................................................ 6-1

6.2 Periodic Maintenance Points.......................................................................6-2

CHAPTER 7 SPECIFICATIONS

7.1 General Specifications ................................................................................. 7-1

7.1.1 Electrical Specifications.......................................................................7-1

7.1.2 Environmental Specifications ...............................................................7-2

7.1.3 External Specifications.........................................................................7-2

7.2 Performance Specifications .........................................................................7-3

7.2.1 Performance Specifications .................................................................7-3

APPENDICES

A.1 Hardware Configuration.............................................................................. A-1

A.2 List of Optional Devices ............................................................................. A-4

7.2.2 Expansion Slots ...................................................................................7-4

7.2.3 Clock Accuracy...................................................................................7-4

A.1.1 I/O Map ............................................................................................. A-1

A.1.2 Memory Map .....................................................................................A-2

A.1.3 Interrupt Map .....................................................................................A-3

PS-2000B Series User Manual

Page 6

Preface

Essential Safety Precautions

This manual includes the following cautions concerning procedures that must be followed to operate the PS-B unit correctly and safely. Prior to operating the PS-B, be sure to read this manual and any related materials thoroughly to understand the correct operation and functions of this unit.



 Safety Icons



To explain the correct and safe usage of the PS-B unit, throughout this manual the following icons are provided next to actions requiring special attention. These icons indicate the following situations:

WARNING

CAUTION

Indicates situations where severe bodily injury, death or major equipment damage may occur .

Indicates situations where slight bodily injury or machine damage can occur.

WARNINGS

• To prevent an electric shock, be sure to connect the power

cord terminals to the PS-B unit's terminal block before connecting the power cord to the main power supply.

• Be sure to use only the specified voltage with the PS-B unit. A

fire or electrical shock may occur if voltages used that are beyond the specified range.

• Be sure to turn the unit's power switch OFF before removing

the PS-B unit's cover . This is because the PS-B unit's internal parts carry high voltages.

• Do not modify the PS-B unit in any way. Modifying the unit

can cause a fire or create an electrical hazard.

• Be sure to immediately turn the unit's power switch OFF, dis-

connect the power cord, and contact your local Pro-face distributor if metal particles, water or other types of liquids contact any of the PS-B unit's internal parts.

• Be sure to read and understand Chapter 2 "Hardware Installa-

tion" thoroughly in order to select an appropriate installation location for the PS-B unit.

PS-2000B Series User Manual

Page 7

Preface

WARNINGS

• Be sure to turn the PS-B unit's power switch OFF Before ei-

ther connecting or disconnecting a board or interface connector .

• Do not install the PS-B unit in areas containing flammable

gases.

• Do not use the PS-B unit with aircraft control devices, aero-

space equipment, central trunk data transmission (communication) devices, nuclear power control devices, or medical life support equipment, due to these devices' inherent requirements of extremely high levels of safety and reliability .

• Be sure to design redundant and/or failsafe systems to en-

sure the proper degree of reliability and safety when using the PS-B unit with transportation vehicles (trains, cars and ships), disaster and crime prevention devices, various types of safety equipment, non-life support related medical devices, etc.

PS-2000B Series User Manual

Page 8

Preface

WARNINGS

CAUTIONS

• Do not expose the PS-B to, or operating the PS-B in direct sunlight, high temperatures and humidity , and in areas that have excessive dust and vibration.

• Do not use the PS-B unit in areas where sudden, extreme changes in temperature can occur . These sudden changes may cause condensation to form inside the unit, possibly leading to an accident.

• Be sure the PS-B unit's air circulation vents are clear and clean to prevent the PS-B unit from overheating, and keep the PS-B unit's operation area well ventilated.

• Do not operate or store the PS-B unit near chemicals, or where chemicals can come into contact with the unit.

When PS-B Unit's Hard Disk (HDD) data is lost:

• The Digital Electronics Corporation cannot be held responsible or provide any compensation for damage(s) caused by the loss of data stored in the PS-B unit's hard disk drive (HDD). It is therefore strongly suggested that all important data and software be backed up regularly to an external data backup device.

• Please be aware that the Digital Electronics Corporation bears no responsibility for any damages resulting from the customer's application of this unit's hardware or software.

• Since the PS-B unit's hard disk drive (HDD) is a consumable item, i.e. it has a finite usage lifetime, be sure to back up its data regularly and prepare a spare HDD unit.

• To prevent file data damage, be sure to shut down the PSB unit's OS before turning the power switch OFF.

• After turning OFF the PS-B unit's power, wait until the internal HDD stops spinning before turning on the power again (approx. 5 seconds).

PS-2000B Series User Manual

Page 9

Preface

Documentation Conventions

The list below describes the documentation conventions used in this manual.

Symbol Meaning

Indic at es i m port a nt i nformati on or procedures that m ust be foll owed for corre ct and ri sk -free soft ware / d evice opera t i o n.

Provides useful or im p ort ant s up pl em ental i nformatio n.

*1 Indicat es useful or import ant footnot e i nformat ion.

Refers to us eful or im portant s upplem ent al i nformati on.

1) , 2)

PS-B/PS-B Unit Abbreviation for the PS-2000B Series of Built-in Computers.

FP Abbreviat ion for FP -2500 and FP -2600TFT col or t ouc h panel display.

Indicat es st eps i n a proc edure. B e sure to perform these s t eps in the order gi ven.

PS-2000B Series User Manual

Page 10

Preface

Package Contents

The PS-B unit's packing box contains the items listed below. Please check to confirm that all items shown below have been included.



 PS-B Unit (1)



 Expansion Board Stays (3)



Attachment Screws (6) Clamps (2)

Clamp Screws (2)



 CD-ROM (PS2000B User Manual



and Driver CD) (1) (Japanese/English) (1)



 Installation Brackets (2) (1 set)



Attachment Screws (4)



 USB Cable Bracket (1)



 Installation Guide



 Power Cord (1)



Installation

Guide

• Be careful when handling the PS-B unit not to damage the built-in HDD.

• This cord is designed only for AC100V/AC115V use. Any other voltage will require a different cord.

• The CD-ROM included in this package contains a User Manual, RAS-API Reference Manual, and PS-B Series Utility and Driver files.

Chapter 4 - Setting Up Your PS-B unit

• When you order a PS-B unit built to your specifications, that PS-B package should include each optional items' Installation Guide. Please use that guide to check the contents of each optional items' package.

PS-2000B Series User Manual

Page 11

Preface

UL/c-UL (CSA) Application Notes

The PS2000B-41 units are UL/c-UL (CSA) recognized products. (UL File No. E171486). Please pay special attention to the following instructions when applying for UL/c-UL approval for machinery which includes any of these PS-B units. Equipment with a PS-B mounted in it requires UL/c-UL (CSA) evaluation for the combination of the PS-B and the equipment.

The PS-B conforms as a component to the following standards:

• UL 60950, Third Edition (Standard for Safety of Information Technology Equipment, including Electrical Business Equipment)

• CSA-C22.2 No. 950-M95 (Standard for Safety of Information Technology Equipment, including Electrical Business Equipment)

• PS200B-41 (UL Registration Model: 3180005-01)

If the following requirements are not met, the PS-B unit may fail to meet UL/c-UL (CSA) standard requirements.

• The PS-B unit should be used as a built-in component of end-use product.

• The PS-B unit is intended for indoor use only.

• When connecting the PS-B unit's power cord, be sure to use a cord that is appropriate for the current and voltage used, and that has 0.75 mm2 or larger conductive wires.

• When an end-use product will include the PS-B, be sure to design the PS-B unit's power cut-off switch as a separate disconnect device and locate it where the operator can easily reach it.

• There is a danger of explosion if the PS-B unit's backup battery is incorrectly replaced. This battery should be replaced only with same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.

• Be sure the unit the PS-B is built into uses an UL/c-UL (CSA) approved structure.

PS-2000B Series User Manual

Page 12

Preface

CE Marking Notes

The PS2000B-41 units are CE marked, EMC compliant products.

• Safety

EN60950

• EMI

EN55011 Group1 (Class A), EN61000-3-2, EN61000-3-3

• EMS (EN61000-6-2)

EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11

If following requirements are not met, the PS-B may fail to meet EN60950 standard requirements.

• The PS-B should be used as a built-in component of an end-use product.

• The PS-B is intended for indoor use only.

• When connecting the PS-B unit's power cord, be sure to use a cord that is

appropriate for the current and voltage used, and that has conductive wires that are 0.75 mm2 or larger.

• When an end-use product will include the PS-B, be sure to design the PS-B

unit's power cut-off switch as a separate disconnect device and locate it where the operator can easily reach it.

• There is a danger of explosion if the PS-B unit's backup battery is incorrectly

replaced. This battery should be replaced only with same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.

• Be sure the unit the PS-B is built into uses an EN60950 approved structure.

PS-2000B Series User Manual

Page 13

Preface

Memo

PS-2000B Series User Manual

Page 14

1. Prior to Operating the PS-B Unit

2. PS-B Unit System Configurations

3. PS-B Unit Part Names and Features

Chapter

4. Interface

5. PS-B Unit External Views and Dimensions

1 PS-B Unit Basics

This chapter describes the procedures required prior to operating the PS-B. It also explains the types of peripheral devices that can be connected to the PS-B.

1.1 Prior to Operating the PS-B Unit

The following explanation shows the preparation steps required prior to operating the PS-B.

[When PS-B has no preinstalled OS]

Install commercial OS to your PS-B as necessary. For how to setup the OS, refer to the manual provided with the product.

Connect Peripheral Devices

Turn Display On

Connect Power

Set Up the BIOS

[When PS-B has pre-installed OS]

Install an OS

Install PS-2000B User Manual

and Driver CD Data

Connect the display unit and any optional devices.

1.2 PS-B System Design / 1.3

PS-B Part Names and Features

Connect the PS-B unit's power cord terminals and turn the power switch ON.

2.3 Wiring

Configure the PS-B unit's BIOS.

Chapter 3 BIOS Setup

PS-2000B Series User Manual

Install Required Device Drivers

Install Required Software

Install the PS-B Unit

Install all required software. For software installation instructions, refer to the manual provided with that product.

1–1

Page 15

Chapter 1 – PS-B Unit Basics

When using a Flat Panel Display (FP) as a touch panel, additional preparation steps are required. After all device drivers are installed, complete the following steps prior to installing applications and the PS-B unit.

Install Mouse Emulation Software

Set up Display Parameters

• After hardware setup is completed, the OS must be used to create

partitions and format (initialize) the HDD before any data or applications can be saved to the hard disk drive. For details concerning these procedures, refer to the OS manufacturer's instruction manual.

FP Series User Manual

(color and resolution)

Perform Calibration

• Whenever you turn the PS-B unit's power OFF, wait until the internal

HDD stops spinning (approximately 5 seconds) before turning the power ON again.

1–2

PS-2000B Series User Manual

Page 16

Chapter 1 – PS-B Unit Basics

1.2 PS-B System Design

Up to two HDD units or CF Card units can be connected internally. In addition, an optional CD-ROM drive or FDD unit can be connected externally.

The following diagram shows the peripheral devices that can be connected to the PS-B unit.

PS-B unit built-in components

HDD units

(PSB-HD020/ PSB-HD020-W2KML)

DIM module

(PL-EM128/PL-EM256)

CF Card unit

(PSB-CFU01)

Sound I/O Device

(Commercial type)

LAN

USB

PS-B unit (PS2000B-41)

Keyboard

(Commercial type)

Mouse

(Commercial type)

RAS

Pro-face’s FP unit or DVI-D monitor

Expansion Board Slots

(Accepts commercial-type boards)

RS-232C

FP or commercial-type CRT monitor

CD-ROM drive/FDD unit (PSB-CD/FD01)

When internally connecting two HDD units or two CF Card units (or one of each), be sure to designate one as the master unit and the other as the slave unit; otherwise, a unit malfunction or operation error may occur. For master/slave setup procedures for each unit, refer to that product's instruction manual.

PS-2000B Series User Manual

1–3

Page 17

Chapter 1 – PS-B Unit Basics



 Commercial-type Products



Commercially available expansion boards (PCI bus compatible boards), keyboards, mouse units and printers can all be used with the PS-B. Also, the PS-B unit's built-in USB connector allows USB-type devices to be used as well. However, some commercial PC peripherals may not be compatible with the PS-B. If you experience compatibility problems, contact your local Pro-face distributor.

• Be sure to use only DIM modules manufactured by Digital Electronics Corporation. Certain commercially available DIM modules will not operate properly in the PS-B unit.

• When using USB-type peripheral devices, be sure to thoroughly read that product's instruction manual prior to use.



 Display Unit



Pro-face manufactures a Flat Panel Display (FP series) which can be connected with the PS-B unit.

Some FP display has not only an Analog RGB interface but also a DVI-D interface for the PS-B unit, and can be connected via Pro-face's 10m DVI-D cable.

For details, refer to the FP's catalogue or Installation manual, or contact your local Pro-face distributor.

1–4

PS-2000B Series User Manual

Page 18

Chapter 1 – PS-B Unit Basics

1.3 PS-B Part Names and Features

18 17

1: Power Switch

Turns the PS-B main unit ON or OFF .

2: Power Input T erminal

Connect the AC100V/AC240V power cord terminals here.

3: Power LED (POWER)

Indicates the PS-B unit's power status and also functions as a RAS LED indicator

5.1 RAS Features

4: Hard Disk LED (HDD)

Front

5: Hardware Reset Switch (RESET)

Pressing this switch re-starts the PS-B unit.

6: Keyboard Connector (KEYBOARD)

Connect a PS/2-compatible keyboard here.

7: Mouse Connector (MOUSE)

Connect a PS/2-compatible mouse here.

8: USB Connector (USB)

Provides a USB 1.1 compatible connection. Connect a USB connectable device here.

9: RAS Connector (RAS)

Interface for DIN, DOUT, Watchdog, and Remote Reset features. (D-sub 25-pin male connector)

10: DVI-D Connector (DVI)

Connect a DVI-D monitor here.

1 1: Analog RGB Connector (VGA)

Connect an analog RGB monitor here.

12: RS-232C Connector (COM1)

Selectable between RI and 5V.

13: RS-232C Connector (COM2) 14: RS-232C Connector (COM3)

Selectable between RI and 5V.

PS-2000B Series User Manual

1–5

Page 19

Chapter 1 – PS-B Unit Basics

Front

18 17

15: RS-232C Connector (COM4)

RS-232C interface (D-sub 9 pin male connector). Allows data transfer with other equipment. Peripheral devices can be connected here.

16: Expansion Slots 17: Speaker Output (SPEAKER) 18: Line Input (LINE IN) 19: Microphone Input (MIC) 20: LAN Connector (LAN1/LAN2)

IEEE802.3-compatible Ethernet interface. Changeover between LAN1 and LAN2 is performed automatically .

21: Cooling Fan

22: Cover

This cover is removed when installing an optional CD-ROM/FDD unit, HDD unit, CF Card unit, or DIM module.

23: Maintenance Cover

This cover is removed when installing an HDD unit, CF card, or DIM module.

Right

24: +5 V/RI Changeover Switch (COM1) 25: +5 V/RI Changeover Switch (COM3) 26: Voice Input Connector for CD-ROM 27: CD-ROM/FDD Unit Power Connector 28: FDD unit Connector 29: CD-ROM Drive Connector

1–6

30: Standard Display ON/OFF Switch

When connecting Digital’s Standard Display to the PS-B unit, be sure to set Dip Switch #4 to ON.

24 25 26 27 28 29

Main Unit Internal View

PS-2000B Series User Manual

Page 20

Chapter 1 – PS-B Unit Basics

1.4 Interfaces

1.4.1 RS-232C Interface (COM1/COM2/COM3/COM4)

D-sub 9-pin (Male)

Pin N o. Signal N a me P in N o. Signal N a m e

1CD6DSR

4321

2RXD7RTS 3TXD8CTS 4DTR9RI/+5V

Screw Size: (4-40), Inch type

5 GND FG FG

• The GND terminal is the signal ground. Be sure to connect the GND terminal with the SG (signal ground) terminal of the opposite side's connector.

• The FG and SG terminals are connected inside the PS-B unit. When connecting another device to the PS-B, design your system so that it will form SG short-circuit loop.

Pin No. 9 "+5V/RI" changeover is available only with COM1 and COM3. COM2 and COM4 are fixed to RI. To change the COM1 or COM3 setting from +5V to RI or vice-versa, remove the main unit cover and slide the +5/RI changeover switch to the desired setting. The factory setting is RI.

RI +5V

For COM1

+5V/RI Changeover Switch PS-B Internal View

For COM3

• Be sure to check the interface specifications of the opposite side's connector before changing this setting. Incorrect settings can result in a malfunction or unit damage.

• Be sure to turn the PS-B unit OFF prior to changing internal settings to prevent a malfunction.

PS-2000B Series User Manual

1–7

Page 21

Chapter 1 – PS-B Unit Basics

1.4.2 RAS Interface (RAS)

D-sub 25-pin (Male)

Pin N o. Signa l Na m e Pin No. Signa l Na m e

1GND14GND 2 +5V (100 mA max. ) 15 +5V 3 +12V (100 mA max. ) 16 DIN3 ( + ) 4 NC 17 DIN3 (-) 5 DIN2 (+) 18 RST (+) 6 DIN0 (+) 19 DOUT1 (-) 7 DOUT2 (-) 20 DOUT1 (+) 8 DOUT2 (+) 21 DOUT3 (-)

9 DOUT0 (-) 22 DOUT3 (+) 10 DOUT0 (+) 23 RST (-) 11 DI N2 (- ) 24 DI N1 (- ) 12 DI N0 (- ) 25 NC 13 DIN1 (+ )

Inch-type screws #4-40UNC

Be sure to use only the rated voltage when using the external power output of No. 2 (+5V) and No. 3 (+12V); otherwise a malfunction or unit breakdown may occur.

For RAS feature details, refer to 5.1 RAS Features.



 External Input Signal (Common for DIN and RST Input)



Input Voltage DC12V to DC24V Input Curr ent 7 mA Operating Voltage ON v olt age: 9V (min.), OFF v olt age: 3V (max.) Isolat ion Method Via a photocoupler

(Interface Circuit)

+5V

1.8k

Ω

1/10W

1.8k 1/10W

(Connec tion Ex ample)

Ω

No polarity due to the Sink/ S our c e input.

1–8

PC357

DIN0(+), DIN1(+) DIN2(+), DIN3(+) RST(+)

(12 to 24V)

DIN0(-), DI N1(-) DIN2(-), DI N3(-) RST(-)

D-sub 25-pin connector

Cable

Switch or a certain switching device

DC12V to DC24V

PS-2000B Series User Manual

Page 22

Chapter 1 – PS-B Unit Basics

• Be sure to hold the input level for 1.5 seconds or longer when using general signal input (DIN); otherwise, the signal may not be detected.

• Be sure that the voltage values between terminals will not exceed the rated input voltage. If these values are too high, a unit breakdown may occur.

• Sink/Source-type input prevents polarity reversal problems. (DIN (-) and RST (-) can become positive, and DIN (+) and (RST (+) can become negative.) Be sure that the input voltage does not exceed the rated range.



 External Output Signal (DOUT)



Rated Load Voltage DC12V to DC24V Maximum Load Current 100 mA/ point Maximum V oltage Drop between Terminals 1. 5V (at 100-mA load current) Isolat ion Method Via a photocoupler

(I nterface Cir c u it)

• Be sure to operate the PS-B unit only within the maximum load current range. Excessive load current can cause a unit breakdown.

• Be sure to include terminal to terminal voltage values in your system design calculations for load current and load voltage. When the load current becomes large, a 1.5V (max) drop will occur between the terminals.

PC357

4.7k

DOUT0(+), DOUT1(+) DOUT2(+), DOUT3(+)

SSTA06

DOUT0(-), DOUT1(-)

Ω

DOUT2(-), DOUT3(-)

(Connec tion Ex ample)

Cable

D-sub 25-pin connec tor

Load

DC12V to DC24V

• Be sure to connect the protective diode shown in the above diagram (*1) when connecting an inductive load

PS-2000B Series User Manual

1–9

Page 23

Chapter 1 – PS-B Unit Basics

1.4.3 DVI-D Interface

17 24

24-pin (Female)

Inch-type screws #4-40UNC

Pin N o. Signa l Na m e P in N o. Signa l N am e

1 TMDS DA TA2- 13 NC 2 TMDS DATA2+ 14 NC 3 TMDS DATA2 SHIELD 15 GND 4 NC 16 Hot Plug Detect 5NC17TMDS DATA06 DDC Clock 18 TMDS DATA0+ 7 DDC Data 19 TMDS DATA0 SHIELD 8NC20NC

9 TMDS DA TA1- 21 NC 10 TMDS DA TA1+ 22 TMDS CLOCK SHI E LD 11 TMDS DATA1 SHIELD 23 TMDS CLOCK+ 12 NC 24 TMDS CLOCK-



 Connecting the FP-3700T



When connecting Pro-face’ s FP-3700T to a PS-B unit using the FP-DV01-100<10m> cable, be sure to change the dip switch settings on the PS-B unit’s main circuit board. Refer to the following figure when changing the settings. For details about dip switch positions, refer to 1.3 PS-B Part Names and Features. The factory settings for switches 1 to 4 are all OFF .

ON OFF Def a ult

OFF

1 2 3 4

SW #4 : OFF → ON

SW1 SW2 SW3

SW4

FP-3700T

(with F P-DV01-100)

* 1 When SW4 is ON and used together with a second RGB monitor, the screen

display resolution is fixed to XGA.

• When using Pro-face’s FP Series, be sure to read that unit’s User Manual prior to operation.

• When using a DVI-D monitor together with a second RGB monitor, some RGB monitors may not be able to be used, so please include a monitor test in your system testing.

Reserved Reserved Reserved

All OFF

Different moni t o r

1–10

• When using Pro-face’s FP-DV01-50<5m> cable, use this dip switch’s default setting.

PS-2000B Series User Manual

Page 24

Chapter 1 – PS-B Unit Basics

1.5 PS-B External Views and Dimensions

1.5.1 PS-B Unit

Unit: mm[in.]

Top

118[4.65]

265[10.43]

39[1.54]

260[10.24]

SideFront

PS-2000B Series User Manual

1–11

Page 25

Chapter 1 – PS-B Unit Basics

1.5.2 With CD-ROM/FDD Unit Attached

Unit: mm[in.]

260[10.24]

Top

118[4.65]41[1.61]

265[10.43]

Side Front

1–12

PS-2000B Series User Manual

Page 26

Chapter 1 – PS-B Unit Basics

1.5.3 With RS-232C/RS-485 Conversion Unit Attached

Unit: mm[in.]

Top

118[4.65]

Front Side

21.5[0.85]

265[10.43]

39[1.54]

260[10.24]

PS-2000B Series User Manual

1–13

Page 27

Chapter 1 – PS-B Unit Basics

1.5.4 With Mounting Bracket Attached



 Vertical Installation



Unit: mm[in.]

170[6.69]

[1.38]

55[2.17]

118[4.65]

137[5.39]

155[6.10]

Top

170[6.69]

228[8.98]

16[0.63]

29[1.14]

39[1.54] 260[10.24]

265.5[10.45]

1–14

Front RightLeft

PS-2000B Series User Manual

Page 28



 Horizontal Installation



Chapter 1 – PS-B Unit Basics

Unit: mm[in.]

170[6.69]

55[2.17]

[1.38]

118[4.65]

137[5.39]

155[6.10]

Top

170[6.69]

228[8.98]

260[10.24]

16[0.63]

29[1.14]

118.5[4.67]

39[1.54]

Front RightLeft



 Magnified View of Mounting Bracket Installation Slot



R2.5[0.10]

20[0.79]

5[0.20]

R5.5[0.22]

PS-2000B Series User Manual

1–15

Page 29

Chapter 1 – PS-B Unit Basics



 Attachment Bracket Attachment Screw Hole Dimensions



Use the following dimension drawing to drill the attachment bracket attachment screw holes in the installation panel. Use M4 size screws.



 Only PS-B Unit



4-M4

260[10.24]

170 ± 0.5[6.69 ± 0.02]

(118[4.65])

(55[2.17])

(155[6.10])

Vertical Installation Horizontal Installation



 With CD-ROM/FD Units Attached



137 ± 0.5

[5.39 ± 0.02]

260[10.24]

170 ± 0.5[6.69 ± 0.02]

(55[2.17])

284 ± 0.5[11.18 ± 0.02]

4-M4

(265[10.43])

(302[11.89])

Unit: mm[in.]

4-M4

Unit: mm[in.]

(260)

170±0.5

(55)

Vertical Installation

(159)

178±0.5

(196)

• Depending on the panel's material and design, the panel's installation surface may need to be strengthened. If high levels of vibration are expected and the PS-B unit's installation surface (i.e. an operation panel's door, etc.) can move (i.e. open or close) due consideration should be given to the PS-B unit's weight.

7.1.3 External Specifications

1–16

PS-2000B Series User Manual

Page 30

1. Installing Optional Units and Expansion Boards

2. Installing the PS-B Unit

Chapter

3. Wiring

2 Hardware Installation

This chapter describes the installation of optional units and expansion boards, as well as the PS-B unit setup and wiring procedures.

2.1 Installing Optional Units and Expansion Boards

A wide variety of optional units and expansion boards (PCI bus compatible board *1) manufactured by Digital Electronics Corporation can be used with the PS-B.

Unscrew the four (4) cover attachment screws, and remove the cover. Install the desired unit and/or expansion board as shown in the " PS-B Internal View" drawing.

For the detailed optional unit installation procedures, refer to that unit's "Installation Guide".

WARNINGS

•

Be sure to disconnect the power cord from the power supply and confirm that power is not supplied to the PS-B unit before installing any optional units or expansion boards. Failure to do so can result in an electric shock.

• Use a screwdriver to loosen and tighten the screws. Be sure not to

tighten the screws too tightly . Excessive force can damage the equipment.

• When removing or replacing screws, be careful that they do not fall

inside the PS-B unit's chassis.

1. Including PCI 2.20.

PS-2000B Series User Manual

2–1

Page 31

Chapter 2 – Hardware Installation



 Removing the PS-B Unit's Cover



Lay the PS-B unit on its side and remove the four (4) cover attachment screws. Slide the cover in the direction shown and then up to remove it. (When reattaching

the screws, use a torque of 0.6 to 0.8N•m.)

Can be removed by hand

Removing the rear face Maintenance Cover allows you to easily remove optional units and expansion boards. To remove this cover, unscrew the attachment screws (2), and lift up the cover. (See drawing below). (When reattaching the screws, use a torque of 0.5 to 0.6N•m.)

2–2

PS-2000B Series User Manual

Page 32



 PS-B Internal View



Chapter 2 – Hardware Installation

Expansion Board Interface

(From the bottom,

SLOT1, SLOT2, SLOT3)

Unit Installation Area

The HDD and CF Card units are installed here.

Expansion Board Stays These stays absorb vibration and hold the

expansion boards in place.

 Installing Expansion Board Stays

PS-2000B Series User Manual

2–3

Page 33

Chapter 2 – Hardware Installation



 Installing Expansion Board Stays



Each Expansion Board Stay is designed to support (brace) an Expansion Board. It will also reduce the amount of vibration that reaches the board.

Each stay has two (2) attachment screws. Prior to installing an expansion board, remove the stay's 2 attachment screws and remove the stay. Next, after the board is installed, position the Stay so that its sponge cushion is resting on top of the board. Reattach the Stay's 2 attachment screws and adjust the height of the Stay so that it is pushing down lightly on the board. Tighten both screws to secure the stay.

Sponge

Expansion Board

Expansion Board Stay

Expansion Board Stay Set Screws

(Front)

Expansion Board

Expansion Board Interface

(Rear)

The Expansion Board Stay’s position can be adjusted using the slotted openings in the cover. When the desired position is found, tighten the screws to secure the Stay in place.

SLOT3 Screw Hole

SLOT2 Screw Hole

SLOT1 Screw Hole

2–4

PS-2000B Series User Manual

Page 34

Chapter 2 – Hardware Installation



 USB Cable Clamp Band



The PS-B unit’s Cable Clamp Band is designed to prevent the USB connector from accidentally coming loose due to problems like vibration, bumping, etc.

Attach the clamp holder and clamp band as shown below to secure the connector in place.

To use the Clamp Band with two cables, attach it as shown below. Be sure not to attach the band vertically.

PS-2000B Series User Manual

2–5

Page 35

Chapter 2 – Hardware Installation

2.2 Installing the PS-B Unit

2.2.1 PS-B Unit Installation Cautions



 Ambient Temperature



• The PS-B is designed for vertical installation and the cooling should be performed by a cooling fan instead of natural air circulation.

• Check the ambient temperature at the positions shown in the illustrations below. T emperatures exceeding the proper ambient temperature (5 to 50°C) may lead to product breakdown.

100mm[3.94in.]

Installed Vertically

100mm[3.94in.]

Installed Horizontally



 Installation Angle



• Be sure and try to install the PS-B in an upright position in order to minimize the heat accumulation within the PS-B.

Cooling Fan

Installed Vertically

Installed Horizontally

2–6

PS-2000B Series User Manual

Page 36

Chapter 2 – Hardware Installation



 Installation Area



• Avoid overheating of the PS-B by not installing the unit near other heat-produc-

ing devices.

• Keep the PS-B away from arc-generating devices such as magnetic switches

and non-fuse breakers.

• Avoid operating the PS-B in environments where corrosive gases are generated.

• To ensure maintainability, operability, and ventilation of the PS-B, be sure to

allow a minimum of 50mm clearance between the PS-B and adjacent structure or equipment (70mm clearance is required to the side of a fan). Also, be sure to include sufficient clearance by considering the size and shape of connectors and space required for removing and inserting an expansion board while the PS-B is in the installed position.



 Installed Vertically



Side View

50[1.97]

[1.97]

70[2.76]



 Installed Horizontally



Side View

50[1.97]

70[2.76]

Front View

50[1.97]

[1.97]

Front View

50[1.97]

Unit: mm[in.]

[1.97]

50[1.97]



 Attached to Wall/Side of Panel



Side View

50[1.97]

[1.97]

50[1.97]

PS-2000B Series User Manual

70[2.76]

Front View

50[1.97]

[1.97]

50[1.97]

2–7

Page 37

Chapter 2 – Hardware Installation



 Vibrations and Shocks



• When moving the PS-B mounted on a rack on casters, excessive vibrations and physical shocks may exert on the hard disk drive. Be sure to take extra cautions in the handling.

•

The hard disk drive is a high-precision unit. Avoid subjecting it to sudden movement or shocks. Especially when the PS-B is turned ON, do not change the direction of the unit or reposition the unit , even when it is on a table. Doing so may cause a hard disk malfunction.

PS-B Conf igur a tion Vibration Endurance

Wit h HDD unit Wit h CD-ROM/FDD unit Without a drive

19.6 m/s

4.9 m/s

9.8 m/s

2 2

• When using a fan to provide forced-air cooling, be sure that streams of air do not blow directly on the hard disk. These streams may cause a hard disk malfunction.

2.2.2 Installation Procedures

Use the following procedures to install the PS-B on a panel.

Before attempting the installation, be sure to read "PS-B Unit Installation Cautions" thoroughly to ensure safe and proper installation.

1. Attach the mounting bracket to the PS-B main unit by using the provided four (4) screws. Be sure that the mounting bracket is attached in the correct direction.

Installed Vertically

2–8

(With CD-ROM/FD drive unit attached)

PS-2000B Series User Manual

Page 38

Chapter 2 – Hardware Installation

Installed Horizontally

(With CD-ROM/FD drive unit attached)

Be sure not to use excessive force when tightening the screws. Product damage can result from over-tightening. The appropriate tightening torque is from 1.0 to 1.2 N•m.

2. Drill installation screw holes in the panel.

Be sure to follow the dimensions given for the installation slots and prepare, if necessary, the installation surface of the panel (i.e. attach supports, etc.).

1.5.4 With Mounting Bracket Attached Attachment Bracket

Attachment Screw Hole Dimensions

3. Attach the PS-B main unit to the panel using M4 screws.

First, insert the screws to the installation holes on the panel. However, do not tighten the screws at this point. Next, install the PS-B unit in the panel by hanging the mounting bracket screws holes over the screw heads. Finally, tighten all mounting bracket screws to secure the PS-B unit in place.

Screw

Installed Vertically

PS-2000B Series User Manual

Screw Screw Screw

Installed Horizontally

2–9

Page 39

Chapter 2 – Hardware Installation

2.3 Wiring

2.3.1 Connecting the Power Cord

Connect the power cord to the power input terminal located on the front face of the PS-B unit.

Power Input Terminal

Input terminal for the power supply of AC 100V/AC 240 V. "L" is for the live state and "N" is for the neutral state.

Ground terminal connected to the enclosure of the PSB.

L N

Power Switch

Power Input Terminal Block

Be sure to follow the procedure below to connect the power cord.

WARNINGS

• Be sure that power is not being supplied to the PS-B when

connecting the power cord; otherwise, electrical shocks or product breakdown may result.

• Be sure that the PS-B is operated under the rated power sup-

ply voltage; otherwise, a fire, electrical shock hazards, and product breakdown may result.

(1) Be sure that the PS-B is turned off. (2) Remove the terminal cover by using a Phillips screwdriver. (3) Unscrew and remove the middle screws (3) from the terminal block. Next,

align each crimp contact

with its screw hole and tighten the screw.

2–10

Black

L N

White

1. Recommended crimp contact: Equivalent of V1.25-3 manufactured by J.S.T. Mfg Co., Ltd.

Green/Yellow

6.0 mm [0.24] max.

Ø3.2 mm[0.13] min.

PS-2000B Series User Manual

Page 40

Chapter 2 – Hardware Installation

• Check the crimp contact cord and be sure to attach it to the correct position.

• The proper tightening torque is 0.5 N•m.

• To prevent the possibility of a crimp terminal short, use a crimp terminal that has an insulating sleeve.

(4) Reattach the terminal cover to the original position.

PS-2000B Series User Manual

2–11

Page 41

Chapter 2 – Hardware Installation

2.3.2 Power Supply Precautions

This section provides the precautions in supplying power to the PS-B. Be sure to take the precautions and connect the power cord to the power input terminal block on the rear face of the PS-B.

Twisted-

Constant voltage transformer

pair cable

PS-B

• If the expected voltage fluctuations exceed the specified range, connect a constant voltage transformer.

Constant voltage transformer

AC 100 V

Main

power

source

Main

power

source

AC 200 V

I/O power

source

pair cable

PS-B power

source

I/O

power

source

PS-B power

source

T1 T2

Twisted-

PS-B

I/O device

PS-B

I/O device

7.1 General Specifications

• Use a low-noise power supply between the lines and between the PS-B and its ground. If there is excessive noise, connect an insulating transformer (noise-prevention type).

• Be sure to use a constant voltage

transformer or insulating transformer with capacity of 200 VA or more.

• Wire the power supply of the PS-B separately from the wiring of I/O and motor devices.

• In order to improve the noise immunity, attaching a ferrite core to the power cord is recommended.

• Isolate the main circuit (high voltage and large current) line, I/O signal lines, and power cord, and do not bind or bring then in close contact.

2–12

Main circuit power source

Motor

device

PS-2000B Series User Manual

Page 42

Twisted-pair cable

Chapter 2 – Hardware Installation

• As the countermeasures for surge from light-

ning, connect a lightning surge absorber.

PS-B

Lightning surge absorber

• Ground the lightning surge absorber (E1) and the PS-B (E2) separately

• Select a lightning surge absorber that will not exceed the maximum allowable circuit voltage, even when the power supply voltage rises to the maximum.

2.3.3 Grounding Precautions

(a) Dedicated Ground: Optimal

• Designate the ground from the FG terminal on the rear face of the PS-B as a dedicated ground as illustrated in figure (a).

PS-B

Another

device

Type-D Ground

(b) Shared Ground: Acceptable

PS-B

Type-D Ground

PS-B

Another

device

Another

device

• If a dedicated ground cannot be provided, use a shared ground as illustrated in figure (b).

• Be sure to use grounding wire of 2 mm

or thicker. The grounding point should be as close to the PS-B as possible to make the grounding wires as short as possible. When the grounding wire should be long, use thick, insulated wires and lay the wires through conduits.

• FG and SG are connected inside the PS-B main unit. When connecting with other device, designate the system configuration so that it won't form a SG short-circuit loop.

PS-2000B Series User Manual

2–13

Page 43

Chapter 2 – Hardware Installation

2.3.4 Precautions When Connecting I/O Signal Lines

• Be sure to lay the I/O signal lines separately from the cable of the motor circuit system.

• If the motor circuit cable cannot be wired as a separate system, use shielded cables and ground one end of the shield to the FG terminal of the PS-B.

• In order to improve the noise immunity, attaching a ferrite core to the power cord is recommended.

2–14

PS-2000B Series User Manual

Page 44

3.1 Setup Procedures

3.2 System Parameters

Chapter

3 System Setup

This chapter explains how to enter the PS-2000B Series Unit's system settings, as well as the cautions required both before and during set up.

3.1 Setup Procedures

Normally, use only the factory (default) settings.

Note:

The following settings are those pre-set at the factory.

1) Connect a keyboard to the PS-B.

2) Turn the PS-B's power ON.

3) After the message "Press <DEL> to Enter SETUP" appears, press the [DEL] key until the following screen appears.

Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations Syetem Monitor Setup

Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving

Esc: Quit ↑↓→←: Select Item F10 : Save & Exit Setup

Time,Date,Hard Disk Type...

KEYBOARD ACTION KEYS

Provides a summary of the keyboard keys used to carry out the set up.

SYSTEM SETTING SELECTION AREA

Each of the titles (areas) listed here contains system setting items.

4) Use the arrow keys to move the cursor to the desired selection.

PS-2000B Series User Manual 3-1

Page 45

Chapter 3 - System Setup

3.2 System Parameters

3.2.1 Standard CMOS Features

Normally, use only the factory (default) settings.

Selecting the STANDARD CMOS FEATURES menu item produces the following screen.

Phoenix - AwardBIOS CMOS Setup Utility

Standard CMOS Features

Date (mm:dd:yy): Tue,Jul 2 2001 Time (hh:mm:ss): 14 : 50 : 3

IDE Primary Master [None] IDE Primary Slave [None] IDE Secondary Master [None] IDE Secondary Slave [None]

Drive A [None] Drive B [None]

Video [EGA/VGA] Halt On [All,But Keyboard]

Base Memory 640K Externded Memory 129024K Total Memory 130048K

↑↓→←: Move Enter:Select +/-/PU/PD: Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults



 Date (mm:dd:yy)



Menu Level

Change the day, month, year and century

Item Help

The PS-B unit's internal calendar and clock allow you to set the date. The day of the week is automatically set. The mm/dd/yy (Jan. 1, 2002) format is factory set prior to shipping.

Month: Jan/Feb/Mar/Apr/May/Jun/Jul/Aug/Sep/Oct/Nov/Dec Day:1 to 31 Year: 1999 to 2099



 Time (hh:mm:ss)



The PS-B unit's internal clock can be set.The hh/mm/ss (0:0:0) format is factory set prior to shipping.

Hours: 0 to 23 Minutes: 0 to 59 Seconds: 0 to 59

IDE Primary (Secondary) Master (Slave)



Displays the name of the IDE type Hard Disk connected to the PS-B. Pressing the [Enter] key will call up the Parameter settings menu. For details, refer to 3.2.2 IDE HDD Auto Detection

PS-2000B Series User Manual3-2

Page 46

Chapter 3 - System Setup



Drive A (B)

This setting determines the format used by the PS-B's internal floppy disk drive. The available settings are [None], [360K - 5.25in], [720K - 3.5in], [1.44M - 3.5in], or [2.88M, 3.5in]. The factory settings are Drive A [None] and Drive B [None] and recommended for most users.



Video

The selections for the screen (video) mode. The available settings are [EGA/VGA], [CGA40], [CGA80] and [MONO]. The [EGA/VGA] selection is factory set and recommended for most users.

Halt On



Designates the type of processing that will be performed when an error occurs during the Initial Start-Up's Self Test. The [All But Keyboard] selection is factory set and recommended for most users.

[All Errors] : Displays all errors and stops the unit. [No Errors] : Displays all errors and does not stop the unit. [All,But Keyboard] :Displays all errors, except for those related to

[All,But Diskette] :Displays all errors, except for those related to [All,But Disk/Key] :Displays all errors, except for those related to the disk

the keyboard, and stops the unit. the disk drive (FDD), and stops the unit. drive (FDD) and keyboard, and then stops the unit.

PS-2000B Series User Manual 3-3

Page 47

Chapter 3 - System Setup

3.2.2 IDE HDD Auto-Detection

Selecting either [IDE Primary (Secondary) Master] or [IDE Primary (Secondary) Slave] will call up the following menu. The following example uses the [IDE Primary Master] setting.

Phoenix - AwardBIOS CMOS Setup Utility

IDE Primary Master

IDE HDD Auto-Detection [Press Enter]

IDE Primary Slave [Auto] Access Mode [Auto]

Capacity Cylinder Head Precomp Landing Zone

Sector

↑↓→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults



 IDE HDD Auto-Detection



Menu Level

To auto-detec the HDD's size,

head.... on this channel

Item Help

This setting detects the hard disk connected to the IDE interface.



 IDE Primary (Secondary) Master (Slave)



This setting designates the IDE type Hard Disk's parameter setting method. The available settings are [None], [Auto], or [Manual]. The factory default setting is [Auto] and is recommended for most users.



 Access Mode



This setting designates the IDE type Hard Disk's access mode. The available settings are [CHS], [LBA], [Large], or [Auto]. The factory default setting is [Auto] and is recommended for most users.



 Capacity/Cylinder/Head/Precomp/Landing Zone/ Sector



These settings designate individual IDE-type Hard Disk parameter settings. When the [IDE Primary (Secondary) Master (Slave)] setting is set to [Manual], the Access Mode must be [CHS]. When the [IDE Primary (Secondary) Master (Slave)] setting is set to [Auto], these values are automaticaly detected. [Capacity] is set automaticaly.

PS-2000B Series User Manual3-4

Page 48

Chapter 3 - System Setup

3.2.3 Advanced BIOS Features

Selecting the ADVANCED BIOS FEATURES menu item calls up the following screen.

Virus Warning [Disabled] CPU Internal Cache [Enabled] External Cache [Enabled] CPU L2 Cache ECC Checking [Enabled] Processor Number Feature [Enabled] Quick Power On Self Test [Enabled] First Boot Device [Floppy] Second Boot Device [HDD-0] Third Boot Device [CDROM] Fourth Boot Device [Disabled] Swap Floopy Drive [Disabled] Boot Up Floppy Seek [Enabled] Boot Up NumLock Status [On]

Typematic Rate Setting [Disabled] x Typematic Rate(Chars/Sec) [6] x Typematic Delay (Msec) [250]

Security Option [Set up]

FirstWare Language [English]

Authentication Level [Low]

OS Select For DRAM > 64MB [Non-OS2]

HDD S.M.A.R.T. Capability [Disabled]

Report No FDD For WIN 95 [No]

Video BIOS Shadow [Enabled]

Small Logo (EPA) Show [Disabled]

Phoenix - AwardBIOS CMOS Setup Utility

Advanced BIOS Features

Item Help

Menu Level

Allows you to choose the VIRUS warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempts to write data into this area, BIOS will show a warning message on screen and an alarm will beep

↑↓→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults



 Virus Warning



This setting determines whether to display a warning when a write to the HDD's start-up sector is attempted. The available settings are [Enabled] or [Disabled]. The factory default setting is [Disabled] and is recommended for most users.



 CPU Internal Cache



This setting determines the usage of the CPU's internal cache memory. The available settings are [Disabled] or [Enabled]. The factory default setting is [Enabled] and is recommended for most users.



 External Cache



This setting enables/disables external cache memory. The available settings are [Disabled] or [Enabled]. The factory default setting is [Enabled] and is recommended for most users.



 CPU L2 Cache ECC Checking



This setting turns ON or OFF external(L2) SEcondary Cache Memory's ECC (Error Check Correction). The available settings are [Disabled] and [Enabled]. The factory default setting is [Enabled] and is recommended for most users.

PS-2000B Series User Manual 3-5

Page 49

Chapter 3 - System Setup



 Processor Number Feature



This option appears only when the CPU is a Pentium

III processor . If this setting is set to Enabled, it will check the CPU's serial number. If you do not need to know the serial number, set this option to [Disabled]. If this is turned ON, use the "Serial Number Control Program" found on Intel's web site to perform the check.



 Quick Power On Self Test



This setting determines whether the quick self test is performed when the power is turned on. The available settings are [Disabled] or [Enabled]. The factory default setting is [Enabled] and is recommended for most users.



 First/ Second/ Third/ Fourth Boot Device



The selections for the search drive sequence of the operating system. The available settings are [Floppy], [LS120], [HDD-0], [SCSI], [CDROM], [HDD-1], [HDD-2], [HDD-3], [ZIP100], [USB-FDD], [USB-ZIP], [USB-CDROM], [USBHDD], [LAN], and [Disabled]. Factory settings are: First: [Floppy], Second: [HDD-0], Third: [CDROM], Fourth: [Disabled].



 Swap Floppy Drive



This setting swaps Drives A and B. The available settings are [Disabled] or [Enabled]. The factory default setting is [Disabled] and is recommended for most users.



 Boot Up Floppy Seek



The setting checks whether the floppy disk drive is installed during the system boot-up process. The available settings are [Disabled] or [Enabled]. The factory default setting is [Enabled] and is recommended for most users.



 Boot Up Numlock Status



This setting specifies the Numlock key status upon the startup. The available settings are [On] and [Off]. The factory default setting is [On] and is recommended for most users.



 Typematic Rate Setting



The setting specifies the keyboard speed used when repeating characters. The available settings are [Enabled] and [Disabled]. The factory default setting is [Disabled] and is recommended for most users.



 Typematic Rate (Chars/ Sec)



This setting specifies the actual typematic rate (repeated character input per second) when the [Typematic Rate Setting] option is set to [Enabled]. The settings are used to determine how many repeats are performed in one second. The factory default setting is [6] and is recommended for most users.



 Typematic Delay (Msec)



When [Typematic Rate Setting] is set to [Enabled], this setting determines the delay period until the initial repetition is started. The [250] selection is factory set and is recommended for most users.

PS-2000B Series User Manual3-6

Page 50

Chapter 3 - System Setup



 Security Option



This setting designates the area to request a password. If a password needs to be entered, select [Setup] in BIOS setup, or [System] during system startup. This setting is NOT available if the password is not set in the [SET SUPERVISOR PASSWORD] or [SET USER PASSWORD] areas. The factory default setting is [Setup] and is recommended for most users.

[SET SUPER VISOR PASSWORD] [SET USER PASSWORD]



 FirstWare Language



3.2.14 Set Supervisor Password

3.2.15 Set User Password

This PS Series unit does not contain the FirstWare Language selection. Plese do not set/use this setting.



 Authentication Level



Selections can be [High], [Medium], or [Low]. Factory setting is [Low].



 OS Select For DRAM > 64MB



The available settings are [Non-OS2] and [OS2]. The factory default settting is [Non-OS2] and is recommended for most users.



 HDD S.M.A.R.T Capability



This feature enables/disables the HDD unit's SMART (Self-Monitoring Analysis and Reporting Technology) feature. The available selections are [Enabled] and [Disabled], [Disabled] is factory set and recommended for most users.



 Report No FDD For WIN 95



This setting determines if the FDD node is reported by BIOS to WIN95. The available settings are [No] and [Yes]. The factory default setting is [No] and is recommended for most users.



 Video BIOS Shadow



This feature enables/disables copying of Video BIOS to RAMF (video accellerator). The available selections are [Enabled] and [Disabled], [Enabled] is factory set and recommended for most users.



 Small Logo (EPA) Show



Enables/disables the initial display at startup of the EPA logo. The available selections are [Enabled] and [Disabled], [Disabled] is factory set and recommended for most users.

PS-2000B Series User Manual 3-7

Page 51

Chapter 3 - System Setup

3.2.4 Advanced Chipset Features

Selecting the ADVANCED CHIPSET FEATURES menu item calls up the following screen.

Phoenix - AwardBIOS CMOS Setup Utility

Advanced Chipset Featrues

SDRAM CAS Latency Time [3] SDRAM Cycle Time Tras/Trc [Auto] SDRAM RAS-to-CAS Delay [Auto] SDRAM RAS Precharge Time [Auto] System BIOS Cacheable [Disabled] Video BIOS Cacheable [Disabled] Memory Hole At 15M-16M [Disabled] CPU Latency Timer [Enabled] Delayed Transaction [Enabled] AGP Graphics Aperture Size [64MB] On-Chip Video Window Size [64MB]

↑↓→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7 :Optimized Defaults

SDRAM CAS Latency Time



Menu Level

Item Help

Designates the clock counts used, from the enabling of CAS to the start of the burst transmission. Can be set to either [3] or [2]. Factory default setting is [3] and strongly recommended for most users.

SDRAM Cycle Time Trans/Trc



Designates the number of SLCK's for an access cycle, i.e. the minumum required time from when a bank is activated to the activation of an identical bank. Settings are [7/9], [5/7] or [Auto]. Factory default setting is [Auto] and strongly recommended for most users.

SDRAM RAS-to-CAS Delay



Designates the timing delay used between RAS and CAS strobe signals. Settings are [2], [3], or [Auto]. Factory default setting is [Auto] and strongly recommended for most users.

SDRAM RAS Precharge Time



Designates the pre-charge time value used, to allow RAS to accumulte its charge before DRAM refresh. Settings are [2], [3], or [Auto]. Factory default setting is [Auto] and strongly recommended for most users.



System BIOS Cacheable

Sets whether the System BIOS’ Cache is used or not. When the OS is set to use this cache, the PS-B unit’s processing speed will increase. Settings available are [Enabled] and [Disabled]. The factory setting is [Disabled] and is recommended for most users.

PS-2000B Series User Manual3-8

Page 52

Chapter 3 - System Setup



Video BIOS Cacheable





Sets whether the Video BIOS Cache is used or not. Settings available are [Enabled] and [Disabled]. The factory setting is [Disabled]. When this feature is [Enabled], the BIOS ROM range available for caching is from C0000h - F7FFFh, which will improve video performance. However, if another program tries to write

to this area of memory, a system error may occur.



Memory Hole At 15M-16M





This setting determines whether to designate the memory space from 15MB to 16MB as the buffer area for the ISA bus card. The available settings are [Disabled] and [Enabled]. The factory default setting is [Disabled] and is recommended for most users.





CPU Latency Timer



If Enabled, a deferrable CPU cycle will only be Deferred after it has been in a Snoop Stall for 31 scans and another ADS# has arrived. If Disabled, changeable CPU cycles will be changed after an ADS number is received.





Delayed Transaction



Designates the length of the pre-charge time. The available settings are [Enabled] and [Disabled]. The factory default setting is [Enabled] and is recommended.





AGP Graphics Aperture Size



Designates the address range used for PCI memory addresses allocated to AGP graphic memory. The available settings are [64MB] or [32MB]. [64MB] is the factory setting.





On-Chip Video Window Size



Designates the on-chip video window size used by the VGA driver. The available settings are [Disabled] and [64MB]. The factory default setting is [64MB] and is recommended for most users.

PS-2000B Series User Manual 3-9

Page 53

Chapter 3 - System Setup

3.2.5 Integrated Peripherals

Selecting INTEGRATED PERIPHERALS SETUP menu item Displays the following screen.

Phoenix - AwardBIOS CMOS Setup Utility

Integrated Peripherals

On-Chip Primary PCI IDE [Enabled] On-Chip Seconary PCI IDE [Enabled] IDE Primary Master PIO [Auto] IDE Primary Slave PIO [Auto] IDE Secondary Master PIO [Auto] IDE Secondary Slave PIO [Auto] IDE Primary Master UDMA [Auto] IDE Primary Slave UDMA [Auto] IDE Secondary Master UDMA [Auto] IDE Secondary Slave UDMA [Auto] USB Controller [Enabled] USB Keyboard Support [Auto] USB Mouse Support [Disabled] Init Display First [PCI Slot] AC97 Audio [Enabled] Onboard LAN1 [Enabled] Onboard LAN2 [Enabled] IDE HDD Block Mode [Enabled] Onboard FDC Controller [Enabled] Onboard Serial Port 1 [3F8/IRQ4] Onboard Serial Port 2 [2F8/IRQ3]

Onboard Parallel Port [Disabled] x Parallel Port Mode SPP x EPP Mode Select EPP1,7 x ECP Mode Use DMA 3

Onboard Serial Port 3 [3E8]

Serial Port 3 Use IRQ [IRQ11]

Onboard Serial Port 4 [2E8]

Serial Port 4 Use IRQ [IRQ10]

Menu Level

Item Help

↑↓→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults



On-Chip Primary (Secondary) PCI IDE

Designates the internal IDE port's setting. The two selections available are [Disabled] and [Enabled]. The [Enabled] selection is factory set and recommended for most users.



IDE Primary (Secondary) Master (Slave) PIO

Designates the Primary (Secondary) Master Drive's PIO (Programmed Input/ Output) Operation Mode. The selections available are [Auto], [Mode0], [Mode1], [Mode2], [Mode3], or [Mode4]. The [Auto] selection is factory set and recommended for most users.



IDE Primary (Secondary) Master (Slave) UDMA

Designates the Primary (Secondary) Master Drive's UDMA Operation Mode. The two selections available are [Auto] or [Disabled]. The [Auto] selection is factory set and recommended for most users.



USB Controller

Select [Enabled] or [Disable] when attaching a USB device. The [Disabled] selection is factory set and recommended for most users. When using the USB I/F or the USB connector for connecting the touch panel, set this item to “Enabled”.

PS-2000B Series User Manual3-10

Page 54

Chapter 3 - System Setup

USB Keyboard Support



Select [Enabled] or [Disable] if your system contains a USB controller and you wish to use a USB keyboard. The available settings are [Disabled] and [Enabled]. The factory default setting is [Auto]. If, however, the USB Controller is set to [Disabled], this setting cannot be changed.

 USB Mouse Support

This setting allows you to connect a USB mouse, even if the OS does not support it. It allows the BIOS to use a mouse driver and treats the

mouse as if it were a PS/2 type mouse.The available settings are [Disabled] and [Enabled]. The factory default setting is [Auto]. If, however, the USB Controller is set to [Disabled], this setting cannot be changed.

Init Display First



When both a PCI and an AGP display boards are installed, this setting

designates which will have first priority. Settings are [PCI slot] or [Onboard/AGP]. The factory default setting is [PCI slot].

AC97 Audio



Enables or disables the 810 chipset support for AC97 Audio. The available settings are [Disabled] or [Auto]. The factory default setting is [Auto].



Onboard LAN 1 (2)

Disables/enables the LAN connector. The available settings are [Disabled] and [Enabled]. The factory default setting is [Enabled].





Internal EDID



The available settings are [Disabled] and [Enabled]. The factory default setting

is [Disabled].





IDE HDD Block Mode



This setting determines whether to enable the Block Mode on the HDD support-

ing the Block Mode. The available settings are [Disabled] and [Enabled]. The factory default setting is [Enabled] and is recommended for most users.



Onboard FDC Controller

Designates whether the PS-B's FDD(Floppy Disk Drive) controller is enabled or disabled. Settings available are [Disabled] or [Enabled]. The [Enabled] selection is factory set.



Onboard Serial Port 1

Designates the PS-B's Serial Port 1 I/O address. The selections include [Disabled], [Auto], [3F8/IRQ4], [2F8/IRQ3], [3E8/IRQ4] and [2E8/IRQ3]. The [3F8/IRQ4] selection is factory set and recommended for most users.



Onboard Serial Port 2

Designates the PS-B's Serial Port2 I/O address. The selections include [Disabled], [Auto], [3F8/IRQ4], [2F8/IRQ3], [3E8/IRQ4] and [2E8/IRQ3]. The [2F8/IRQ3] selection is factory set and recommended for most users.

PS-2000B Series User Manual 3-11

Page 55

Chapter 3 - System Setup

Onboard Parallel Port



Normally not used. The [Disabled] selection is factory set and recommended

for most users.

Parallel Port Mode



Normally not used.



EPP Mode Select

Normally not used.



ECP Mode Use DMA

Normally not used.



PWRON After PWR-Fail

This feature is not supported.



Onboard Serial Port 3

Designates the interupt number for the PS-B's on-board Serial Port3. The

selections include [3F8], [2F8], [3E8] or [2E8]. The [3E8] selection is factory set and recommended for most users.

Serial Port 3 Use IRQ



Designates the interupt number for the PS-B's on-board Serial Port3.The

selections include [IRQ9], [IRQ10], [IRQ11] or [IRQ15]. The [IRQ11] selection is factory set and recommended for most users.

Onboard Serial Port 4



Designates the interupt number for the PS-B's on-board Serial Port4. The

selections include [3F8], [2F8], [3E8] or [2E8]. The [2E8] selection is factory set and recommended for most users.

Serial Port 4 Use IRQ



Designates the interupt number for the PS-B's on-board Serial Port4. The

selections include [IRQ9], [IRQ10], [IRQ11] or [IRQ15]. The [IRQ10] selection is factory set and recommended for most users.

PS-2000B Series User Manual3-12

Page 56

Chapter 3 - System Setup

3.2.6 Power Management Setup

Selecting the POWER MANAGEMENT SETUP menu item calls up the following screen.

Phoenix - AwardBIOS CMOS Setup Utility

Power Management Setup

ACPI Function [Enabled] Power Management [ User Define] Video Off Method [DPMS Video Off In Suspend [Yes] Suspend Type [Stop Grant] Suspend Mode [Disabled] HDD Power Down [Disabled] Wake-up by PCI card [Disabled]

**Reload Global Timer Events** Primary IDE 0 [Disabled] Primary IDE 1 [Disabled] Secondary IDE 0 [Disabled] Secondary IDE 1 [Disabled] FDD,COM,LPT Port [Disabled] PCI PIRQ[A-D]# [Disabled]

↑↓→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

]

Menu Level

Item Help

 ACPI Function

Enables/disables the ACPI feature. Selections are [Enabled] or [Disabled]. [Enabled] is factory set and recommended for most users.



Power Management

You can choose from three power management options. These are [User Define], [Min Saving] or [Max Saving]. The [User Define] selection is factory set and recommended for most users.





Video Off Method



This setting determines the method to blank the display screen. The available settings are [Blank Screen], [V/H SYNC+Blank], and [DPMS Supported]. The [Blank Screen] selection blanks the display. The [V/H SYNC+Blank] blanks the display and also suspends the Vertical/Horizontal synchronization signal of the display. The [DPMS Supported] selection controls the operation when a CRT that supports DPMS

is used. The

factory default setting is [DPMS] and is recommended for most users.





Video Off In Suspend



Designates how the monitor is blanked. The available settings are [Yes] and [No]. The factory default setting is [Yes].

*1 This standard is approved by the VESA (Video Electronics Standards Association).

PS-2000B Series User Manual 3-13

Page 57

Chapter 3 - System Setup



Suspend Type





Designates the type of suspend method used. The available settings are [Stop Grant] and [PWRON Suspend]. The factory default setting is [Stop Grant].





Suspend Mode



When enabled, designates the period of time before all devices except the CPU are shut down. The available settings are [1Min], [2Min], [4Min], [8Min], [12Min], [20Min], [30Min], [40Min], [1Hour] and [Disabled]. The factory default setting is [Disabled].



HDD Power Down

After the hard disk's motor stops, this setting designates the length of time until the PS-B unit enters energy-saving mode. The available selections are[1Min], [2Min], [3Min], [4Min], [5Min], [6Min], [7Min], [8Min], [9Min], [10Min], [11Min], [12Min], [13Min], [14Min], [15Min] or [Disabled]. [Disabled] is factory set and recommended for most users.



Wake-Up by PCI Card

Enables/disables waking up the PS-B's system via an expansion board signal. The two selections available are [Disabled] and [Enabled]. The [Disabled] selection is factory set and recommended for most users.





**Reload Global Timer Events**



This feature sets the event that reloads the amount (period) of PS-B unit idle time prior to changing to energy-saving mode. Thus, when an event occurs for any of the items in this area that are set to [Enabled], the PS-B unit will recover from energy-saving mode.Enabled/disabled is possble for the following settings: Primary IDE 0, Primary IDE 1, Secondary IDE 0, Secondary IDE 1, FDD, COM, LPT Port, PCI PIRQ[A-D]#. Factory settings are [Disabled] and recommended for most users.

PS-2000B Series User Manual3-14

Page 58

Chapter 3 - System Setup

3.2.7 PnP/PCI Configurations

Selecting the PnP/PCI CONFIGURATION menu item Displays the following screen.

Phoenix - AwardBIOS CMOS Setup Utility

PNP/PCI Configurations

Reset Configuration Data [Disabled]

Resources Controlled By [Auto(ESCD)] x IRQ Resources [Press Enter] x DMA Resources [Press Enter]

PCI/VGA Palette Snoop [Disabled] Assign IRQ For VGA [Enabled] INT Pin 1 Assignment [Auto] INT Pin 2 Assignment [Auto] INT Pin 3 Assignment [Auto] INT Pin 4 Assignment [Auto] INT Pin 5 Assignment [Auto] INT Pin 6 Assignment [Auto] INT Pin 7 Assignment [Auto] INT Pin 8 Assignment [Auto]

↑↓→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

Reset Configuration Data



Menu Level

Default is Disabled. Select Enabled to reset Extended System Configuration Data (ESCD) when you exit Setup if you have installed a new add-on and the system reconfiguration has caused such a serious conflict that the OS cannot boot

Item Help

Designates whether ESCD (Extended System Configuration Data) data should be erased or not. The two selections available are [Disabled] and [Enabled]. The [Disabled] selection is factory set and recommended for most users.

Resources Controlled By



The Plug-and-Play feature allows you to designate whether the allocation of I/ O Port, IRQ and DMA resources is performed automatically or manually. The two selections available are [Manual] or [Auto(ESCD)]. If [Auto(ESCD)] is selected, the IRQ Resources and DMA Resources selection will be disabled. The [Auto(ESCD)] selection is factory set and recommended for most users.

IRQ Resources



When resources are controlled using [Manual], manually set each IRQ assignment.



DMA Resources

3.2.8 IRQ Resources

When [Resources Controlled By] is set to [Manual], manually set each DMA assignment.



PCI/VGA Pallet Snoop

3.2.9 DMA Resources

The two selections available are [Disabled] and [Enabled]. The [Disabled] selection is factory set and recommended for most users. However, if a VGA or MPEG board is used, set this to [Enabled]. For setting details, refer to your VGA or MPEG board's Installation guide.

Assign IRQ For VGA



Designates if the interrupt used by the VGA controller is enabled or disabled. The two selections available are [Disabled] and [Enabled]. The [Enabled] selection is factory set and recommended for most users.

INT Pin 1(2/3/4/5/6/7/8) Assignment



Used when manually allocating the PCI interrupt signal to an IRQ. Select either [Auto], [3], [4], [5], [7], [9], [10], [11], [12], [14], or [15]. Factory setting is [Auto].

PS-2000B Series User Manual 3-15

Page 59

Chapter 3 - System Setup

3.2.8 IRQ Resources

Select IRQ Resources from the PnP/ PCI Configurations menu and the following screen will appear.

Phoenix - AwardBIOS CMOS Setup Utility

IRQ Resources

IRQ-3 assigned to [PCI/ISA PnP] IRQ-4 assigned to [PCI/ISA PnP] IRQ-5 assigned to [PCI/ISA PnP] IRQ-7 assigned to [PCI/ISA PnP] IRQ-9 assigned to [PCI/ISA PnP] IRQ-10 assigned to [PCI/ISA PnP] IRQ-11 assigned to [PCI/ISA PnP] IRQ-12 assigned to [PCI/ISA PnP] IRQ-14 assigned to [PCI/ISA PnP] IRQ-15 assigned to [PCI/ISA PnP]

↑↓→←:Move Enter:Select +/-/PU/PD: Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults



 IRQ-3 (4/5/7/9/10/11/12/14/15) assigned to



Menu Level

Legacy ISA for devices comPS-Biant with the original PC AT bus specification, PCI/ISA PnP for devices comPS-Biant with the PS-Bug and PS-Bay standard whether designed for PCI or ISA bus architecture

Item Help

This setting determines the type of device assigned to the IRQ. This function is available when the [PnP/ PCI Configurations] menu's [Resources Control By] option is set to [Manual].

[PCI/ISA PnP] .. Select to use a PnP-ready PCI or ISA card.

[Legacy ISA] .... Select to use a non-PnP ISA card.

The initial settings are all [PCI/ISA PnP].

PS-2000B Series User Manual3-16

Page 60

Chapter 3 - System Setup

3.2.9 DMA Resources

Selecting DMA Resources from the PnP/PCI Configuration menu and the following screen will appear.

Phoenix - AwardBIOS CMOS Setup Utility

DMA Resources

DMA-0 assigned to [PCI/ISA PnP] DMA-1 assigned to [PCI/ISA PnP] DMA-3 assigned to [PCI/ISA PnP] DMA-5 assigned to [PCI/ISA PnP] DMA-6 assigned to [PCI/ISA PnP] DMA-7 assigned to [PCI/ISA PnP]

↑↓→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7 :Optimized Defaults



 DMA-0 (1/3/5/6/7) assigned to



Menu Level

Legacy ISA for devices comPS-Biant with the original PC AT bus specification, PCI/ISA PnP for devices comPS-Biant with the PS-Bug and PS-Bay standard whether designed for PCI or ISA bus architecture

Item Help

This setting determines the type of device assigned to the IRQ. This function is available when the [PnP/ PCI Configurations] menu's [Resources Control By] option is set to [Manual].

[PCI/ISA PnP] .. Select to use a PnP-ready PCI or ISA card.

[Legacy ISA] .... Select to use a non-PnP ISA card.

The initial settings are all [PCI/ISA PnP].

PS-2000B Series User Manual 3-17

Page 61

Chapter 3 - System Setup

3.2.10 System Monitor Setup

Select PC Health Status from the System Monitor Setup and the following screen will appear.

Phoenix - AwardBIOS CMOS Setup Utility

System Monitor Setup

CPU Warning Temperature [Disabled] System Warning Temperature [Disabled] Warning Voltage Vcore A [Disabled] Warning Voltage Vcore B [Disabled] Warning Voltage +3.3V [Disabled] Warning Voltage +5V [Disabled] Warning Voltage +12V [Disabled] Warning Voltage -12V [Disabled] CPU FAN Speed Limit [Disabled] Power FAN Speed Limit [Disabled]

↑↓→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7 :Optimized Defaults



 CPU Warning Temperature



Menu Level

Item Help

This setting designates the CPU temperature at which a warning will be issued. The available settings are [70°C/158°F], [75°C/167°F], [80°C/176°F], [85°C/ 185°F], [90°C/194°F] and [Disabled]. The factory default setting is [Disabled].

• When using a PentiumIII 1GHz CPU, select the [75°C/158°F] setting. When using a Celeron 566MHz CPU, select the [90°C/194°F] setting.



 System Warning Temperature



This setting designates the system temperature at which a warning will be issued. The available settings are [70°C/158°F], [75°C/167°F], [80°C/176°F], [85°C/ 185°F], [90°C/194°F] and [Disabled]. The factory default setting is [Disabled].



 Warning Voltage Vcore A



When enabled, this setting designates that a warning will be issued if the CPU core voltage change exceeds that level. The available settings are [+/-6%], [+/8%] and [Disabled]. The factory default setting is [Disabled].



 Warning Voltage Vcore B



PS-2000B Series User Manual3-18

Page 62

Chapter 3 - System Setup



 Warning Voltage +3.3V



When enabled, this setting designates that a warning will be issued if the voltage change exceeds +3.3V's designated range. The available settings are [+/-6%], [+/8%] and [Disabled]. The factory default setting is [Disabled].



 Warning Voltage +5V



When enabled, this setting designates that a warning will be issued if the voltage change exceeds +5V's designated range. The available settings are [+/-6%], [+/8%] and [Disabled]. The factory default setting is [Disabled].



 Warning Voltage +12V



When enabled, this setting designates that a warning will be issued if the voltage change exceeds +12V's designated range. The available settings are [+/-6%], [+/8%] and [Disabled]. The factory default setting is [Disabled].



 Warning Voltage -12V



When enabled, this setting designates that a warning will be issued if the voltage change exceeds -12V's designated range. The available settings are [+/-6%], [+/8%] and [Disabled]. The factory default setting is [Disabled].



 CPU FAN Speed Limit



When enabled, this setting designates the allowed speed range reductions allowed for CPU FAN. The available settings are [-30%], [-50%] and [Disabled]. The factory default setting is [Disabled].



 Power FAN Speed Limit



When enabled, this setting designates the allowed speed range reductions allowed for Power FAN. The available settings are [-30%], [-50%] and [Disabled]. The factory default setting is [Disabled].

PS-2000B Series User Manual 3-19

Page 63

Chapter 3 - System Setup

3.2.11 Frequency/Voltage Control

Selecting the Frequency/Voltage Control menu item produces the following screen.

Phoenix - AwardBIOS CMOS Setup Utility

Frequency/Voltage Control

Auto Detect DIMM/PCI Clk [Enabled] Spread Spectrum [Disabled]

↑↓→←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7 :Optimized Defaults



 Auto Detect DIMM/PCI CLK



Menu Level

To auto-detect the HDD's size, head... on this channel

Item Help

This setting designates the auto detect of the DIMM/PCI clock. The available settings are [Enabled] and [Disabled]. The factory default setting is [Enabled] and strongly recommended for users.



 Spread Spectrum



This setting allows you to set the CPU Clock generator's spread Spectrum. The available settings are [Enabled] and [Disabled]. The factory default setting is [Disabled] and strongly recommended for users.

PS-2000B Series User Manual3-20

Page 64

Chapter 3 - System Setup

3.2.12 Load Fail-Safe Defaults

When the Menu screen's [Load Fail-Safe Defaults] is selected, you are able to designate if the minimum number of System Settings is loaded in or not. The selections are [Y] and [N].

3.2.13 Load Optimized Defaults

Selecting [Load Optimized Defaults] designates whether or not you will revert to the PS-B unit’s factory settings. The selections are [Y] and [N].

Note:

When the PS-B unit uses its factory settings, the USB interface cannot be used. For information about connecting the Touch Panel via the USB connector, see 1.2.1 Setting Up the Touch Panel Connection. For information about connecting the USB I/F, see 1.2.2 Using the USB Interface.

3.2.14 Set Supervisor Password

This password is used to change system information settings. It is designed to prevent unapproved users from changing the system information settings. Entering up to 8 characters here will overwrite the current password.

When you wish to have no password, click on the [Enter] key. Next, the words "PASSWORD DISABLE" will appear, providing confirmation that the Password is no longer set.

When password input is required, use the [Advanced BIOS Features] area's [Security Option] feature to enter the password.

3.2.3 ADVANCED BIOS FEATURES

PS-2000B Series User Manual 3-21

Page 65

Chapter 3 - System Setup

3.2.15 Set User Password

This password is used to view system information settings. It is designed to prevent unapproved users from viewing the system information settings. Entering up to 8 characters here will overwrite the current password.

When you wish to have no password, click on the [Enter] key. Next, the words "PASSWORD DISABLE" will appear, providing confirmation that the Password is no longer set.

When password input is required, use the [Advanced BIOS Features] area's [Security Option] feature to enter the password.

See 3.2.3 ADVANCED BIOS FEATURES

• When using either [Set Supervisor Password] or [Set User Password], you can easily view and change system settings.

• When using BOTH the [Set Supervisor Password] and [Set User Password] features, [Set User Password] will allow you to only view system data, not change it.

3.2.16 Save & Exit Setup

This feature saves the settings entered in the Setup Utility and restarts the PS-B unit.

3.2.17 Exit Without Saving

This feature quits the Setup Utility program without saving any settings entered.

PS-2000B Series User Manual3-22

Page 66

1. CD-ROM Contents

2. Setting up Your PS-B Unit

3. Installing Drivers

Chapter

4. Application Features

5. Windows

4 Setting up Your PS-B Unit

An accessory CD-ROM disk is included with the PS-B unit. This CD-ROM contains special programs designed for the PS-B that are not supported by stan-

dard versions of Windows

4.1 CD-ROM Contents

4.1.1 Software

This section explains the organization of the software included in the accessory CD-ROM.

PS-2000B User Manual & Driver CD

[Driver]

[Audio] Audio Driver <Supported OS types>

2000 and Windows®XP.

2000 and Windows®XP Usage Cautions

Windows Windows

2000

[Chipset] Chipset Driver <Supported OS types>

Windows

[Win2000]

[Display] Display Driver <Supported OS types>

Windows

[Manual] <User Manual>

[Eng] PDF Manual (English Version) [Jpn] PDF Manual (Japanese Version)

[Reader] <PDF Reader>

[Eng] Acrobat [Jpn] Acrobat

[Utility] <PS-B Utility Tools>

[Shutdown] Remote Shutdown [RASSvr] Remote RAS Server for PC

Utility Setup <Supported OS types>

[Win2000] Windows®2000 [WinXP] Windows

2000

Reader (English Version)

Reader (Japanese Version)

PS-2000B Series User Manual

4–1

Page 67

Chapter 4 – Setting up Your PS-B Unit

4.2 Setting up Your PS-B Unit

There are two types of PS-B units. One has a hard disk with no pre-installed OS and one has a hard disk with a pre-installed OS. Therefore, the setup procedures used will differ. This manual describes only the procedures for setting up a PS-B unit using a hard disk with no pre-installed OS.

For an explanation of how to set up a PS-B using a hard disk with a pre-installed OS, refer to the "Pre-installed T ype Installation Guide", provided with the HDD unit.

4.2.1 Setup Procedures

First, you will need to install either Windows®2000 or W indows®XP. Y ou also need to install any required utility software.



 Installing the HDD Unit



Check to see if a hard disk unit is installed in your PS-B unit. If it is not, please install one prior to going to the next step.

PSB-HD020 Installation guide



 Setting Up HDD Unit System Information



After you install your HDD unit, you will need set up a variety of system information. Set up this information so that the system recognizes the newly-installed hard disk drive.

PSB-HD020 Installation guide



 Setting Up the OS



Install your operating system. For detailed setup procedures, refer to that product's installation manual.

The PS-B unit supports Windows®2000 and Windows®XP. PS-B unit performance cannot be guaranteed when any other operating system is used.



 PS-B Utility Setup



Install the necessary drivers and utility software from the "PS-2000B Series User Manual & Driver CD".

4–2

• A PS/2 (mini-DIN) type keyboard is required to install the

OS.

• When using a touch panel display with the PS-B, the touch

panel will require an optional mouse emulation software (UPDD). When installing the mouse emulation software, be sure to specify the number of the serial cable's COM port. Visit our website (http://www.pro-face.com/otasuke/) and download the mouse emulation software (UPDD).

PS-2000B Series User Manual

Page 68

Chapter 4 – Setting up Your PS-B Unit



 Installing Software from the PS-2000B Series User Manual & Driver



CD-ROM

To install this software you need to connect Digital Electronics Corporation's optional CD-ROM/FDD (PSB-CD/FD01) unit to the PS-B.

To begin the installation, click on the "Setup.exe" file in your OS' folder.

Example) With Windows

D:\Utility\

WinXP*\Disk1\Setup.exe (When the CD-ROM drive is "D")

For Windows

2000, this will be "Win2000".

PS-2000B Series User Manual

4–3

Page 69

Chapter 4 – Setting up Your PS-B Unit



 PS-B Hard Disk Data



Setting up the PS-B unit's utilities will create a [Proface] folder on the C drive. The following diagram describes the configuration of this folder.

[Proface]

[PsbApi] API-DLL [Audio] Audio Driver

[Chipset] Chipset Driver (Not included with Windows [Display] Graphic Accelerator Driver [Shutdown]

[Client] Remote Shutdown Client

[Sysmon] System Monitor/RAS Application

• The actual organization may differ depending on your PSB unit's OS.

• Setting up the PS-B unit's utilities automatically copies the hardware control driver (PSSYSMON.SYS) to the system folder.

XP)

4.2.2 Setting Up an HDD with Pre-installed OS

Use the following steps to set up your PS-B unit's HDD unit, which contains the

Windows software.



 Installing the HDD Unit



After opening the PS-B unit's packing box, check that a hard disk unit is installed. If it is not, you will need to install it.

2000 or W indows®XP operating system, related drivers and utility

• Each pre-installed operating system is designed specially for the PS-B unit.

• "Service Pack 4" is included in the Windows unit.

• "Service Pack 2" is included in the Windows

2000 HDD

XP HDD unit.

Pre-installed HDD Unit Installation Guide

4–4

PS-2000B Series User Manual

Page 70

Chapter 4 – Setting up Your PS-B Unit



 Setting Up the PS-B Unit's System Information



If your PS-B unit does not have a pre-installed HDD, you will need to install an HDD unit and then configure that drive's system information. Be sure to check that the system successfully recognizes the drive.

Pre-installed HDD Unit Installation Guide



 Setting Up an HDD with Pre-installed OS



Follow the setup procedures given in the Pre-installed Type HDD Unit Installation Guide.



 PS-B Hard Disk Data



Setting up the PS-B unit's utilities will create a [Proface] folder on the C drive. The following diagram describes the configuration of this folder.

[Proface]

[PsbApi] API-DLL [Audio] Audio Driver

[Chipset] Chipset Driver (Not included with Windows

XP) [Display] Graphic Accelerator Driver [Setup] CD Image [Shutdown]

[Client] Remote Shutdown Client

[Sysmon] System Monitor/RAS Application

• The actual organization may differ depending on your PSB unit's OS.

• Setting up the PS-B unit's utilities automatically copies the hardware control driver (PSSYSMON.SYS) to the system folder.

PS-2000B Series User Manual

4–5

Page 71

Chapter 4 – Setting up Your PS-B Unit

4.3 Installing Drivers

Three types of dedicated PS-B drivers (Audio, Chipset, and graphic accelerator) are available.

Install the required drivers from this data when using a PS-B with no pre-installed OS or when the system recovery has been performed via the recovery menu.

This explanation given in this section assume that the [Proface] folder has been created.

Once drivers are installed in the PS-B unit, they cannot be uninstalled.



 Installing the Audio Driver



Installing the Audio driver enables the OS’ Audio feature. (1) Double-click on the "Setup.exe" file located in the following folder. Follow

the instructions given to install the driver. C:\Proface\Audio\Setup.exe



 Installing the Chipset Driver



Installing the Chipset driver adds the Chipset feature to the OS. (1) Double-click on the "infinst_autol.exe" file located in the following folder.

Follow the instructions given to install the driver. C:\Proface\Chipset\infinst_autol.exe



 Installing the Graphic Accelerator Driver



Installing the Graphic Accelerator Driver will accelerate the screen refresh speed, using special hardware features.

(1) Start "C:\Proface\Display\Win2K_xpm67.exe" file. (2) Select [Next]-[Yes]-[Exit], and then restart the system to complete the instal-

lation.

4–6

PS-2000B Series User Manual

Page 72

Chapter 4 – Setting up Your PS-B Unit

4.4 Special Application Program Features

The special programs designed for the PS-B unit are located in the following folders.

File Nam e Windows®X P Windows®2000

PSB_RAS.DLL PSB_DLL.DLL PSB_IOCS.DLL PSB_Smon.exe C:\Proface\Sysmon PSB_Wps.exe C:\Proface\Sysmon Pssysmon.sys C:\Windows\System32\Drivers C:\Winnt\System32\Drivers



 API-DLL



These dynamic link libraries allow users to access RAS features via custom-made applications. The following three types are available.



 System Monitoring: PSB_DLL.DLL



This dynamic link library allows users to access the PS-B unit's system monitor feature.

C:\Windows\System32 C:\Winnt\System32



 RAS Features: PSB_IOC.DLL



This dynamic link library allows users to access RAS features via custom-made PS-B applications.

For details, refer to the API Reference Manual.



 Shared Memory Access: PSB_RAS.DLL



This dynamic link library allows users to access shared memory via remote RAS features.

For details, refer to the API Reference Manual.



 System Monitoring/RAS Applications: PSB_Smon.exe/



PSB_Wps.exe

The RAS and System Monitoring features allow users to monitor temperature voltage, and fan operation alarms. This program runs on Windows



 System Monitoring Program: PSB_Smon.exe



5.2.3 System Monitoring Operation (PSB_Smon.exe)



 Watchdog Parameter Setup Program: PSB_Wps.exe





 System File: Pssysmon.sys



This system file allows use of the RAS and System Monitoring features. This file should not be modified. If it is modified, the RAS and System Monitoring features may not operate correctly.

PS-2000B Series User Manual

5.2.2 System Monitoring Property Settings (PSB_Wps.exe)

4–7

Page 73

Chapter 4 – Setting up Your PS-B Unit

4.4.1 Uninstalling Utility Software

Utility programs can be uninstalled using the following procedure. (1) Click on the [Control Panel] icon. (2) Click on the [Add/Remove Programs] icon and from the list of installed

programs that appears, select [PS-B Driver and Utility] and click [Add/Remove].

Once drivers are installed in the PS-B unit, they cannot be uninstalled.

4.5 When Using Windows®2000/Windows®XP

4.5.1 Automatic System Log-on Setup

This setting allows users to simplify password entry at startup.



 Windows



(1) Double-click on the [Control Panel]'s [User and Password] icon. (2) Designate the automatic logon user, and deselect the [User must enter the user

name and password to use this computer] checkbox.

(3) Click on the [Advanced] tab, and deselect the [Require users to press Ctrl +

Alt + Del keys before logging on] checkbox.

(4) Click the [Apply] button. Next, when the automatic logon dialog box appears,

enter the password.



 Windows



(1) Select [Run] from the [Start] menu. (2) Enter "Control userpasswords2", and click [OK]. (3) Deselect the [User must enter the user name and password to use this com-

puter] checkbox and click [Apply].

(4) Enter the user name and password for automatic logon and click [OK].

2000

4–8

A password must be assigned for user to perform automatic logon.

If automatic logon is not used, a PS/2 (mini-DIN) type keyboard is required to logon.

PS-2000B Series User Manual

Page 74

Chapter 4 – Setting up Your PS-B Unit

4.5.2 Uninterrupted Power Supply System (UPS)

Be sure to shut down your OS before turning off your machine. Also, use of an uninterrupted power supply is recommended to protect your data from accidental power failures.

An uninterrupted power supply will give you sufficient time to shut down your system safely in case of a power failure, and can even be set up to automatically shut down your Windows

The PS-B unit, however, cannot be used with a 2-Step Inverter Output type uninterrupted power supply. Be sure the unit is a sine-output type power supply.

For details, consult your local UPS system dealer.

4.5.3 Changing System Settings

Your Windows® system's configuration settings will need to be changed when the PS-B unit is connected to a LAN network or printer.

OS.



 Changing the System Configuration Settings



When the Windows® system configuration settings are changed, the following message appears.

Enter the name of the folder where you will save the configuration changes and click [OK].

• Insert the CD labeled "Windows

xx*1 Professional CD-ROM" in the

CD-ROM drive (D: ), and click [OK].

• When copying the file from other locations such as a floppy disk or network server, also click the [OK] button.

• When Your PS-B has No Preinstalled OS

Double-click the [I386] folder in the Windows

CD-ROM.

D:\I386 (When the CD-ROM drive is "D")

• When Your PS-B has a Preinstalled OS

C:\Proface\Setup\I386

1. "xx" is your OS.

Example) When using Windows

PS-2000B Series User Manual

XP: "Windows®XP Professional CD-ROM"

4–9

Page 75

Chapter 4 – Setting up Your PS-B Unit

4.5.4 NTFS File System Conversion

If your PS-B unit has a pre-installed OS, or if your OS is formatted with the Windows file system.

To convert to the NTFS file system, start up Windows command.

convert X: /fs:ntfs (Replace "X" with your drive name.)

DOS-compatible file system (FAT32), it can be converted to the NTFS

Once the file system is converted to the NTFS file system, it cannot be converted back to the Windows file system (FAT32).

and use the following

DOS-compatible

4–10

PS-2000B Series User Manual

Page 76

Chapter

5 Monitoring Features

5.1 RAS Features

5.1.1 PS-B RAS Features

RAS (Reliability , Availability , Serviceability) features include a variety of useful system performance monitoring features, with the main feature being device monitoring. These features are designed to improve overall system reliability.



 Types of Monitoring



The PS-B unit supports the following Alarm Monitoring and External Input Signal features.

1. RAS Features

2. System Monitor/RAS Features

3. Remote RAS

4. Remote Shutdown

Power Voltage Alarm Cooling Fan RPM A larm

Error Monitoring

External I nput Signal

The signal level of the general signal input (DIN) should be 1.5 seconds or longer; otherwise, it may not be detected.



 Alarm Processing



The PS-B provides the following alarm processing (processing or external output signals) in response to the previous page's alarms, or to external signal input.

Exter n al Ou tp u t Si g n al Types of Processing

Internal Temperat ure Alarm Watchdog Timer Timeup SMA RT Alarm General Signal Input (DIN 4-bit, DIN0 to DIN3)

Remote Reset I nput

General Signal Output (DOUT 4-bit, DOUT0 to DOUT3) LED Indicator (2 colors, 1 lamp) Pop-up Message Output Buzz er Out p ut Sy stem Shutdown Sy stem Reset

1. The Remote Input feature can be disabled or enabled, however, a forced hardware

reset cannot be set using the LED settings.

PS-2000B Series User Manual

5–1

Page 77

Chapter 5 – Monitoring Features



 System Monitor



The System Monitor feature (software utilities) allows users to enable or disable the monitoring of any of the above monitoring items and external signal input, as well as to individually set alarm processing settings.

5.2 System Monitor/RAS Features

In addition, System Monitor includes a dynamic link library (API-DLL) feature that gives other applications access to RAS features.

5.1.2 RAS Feature Details



 Error Monitoring





 Power Voltage Alarm



Monitors the status of the PS-B unit's built-in power supply and internal CPU power supply .



 Cooling Fan Rotation Alarm



Monitors the power-supply and CPU cooling fan RPM speeds.



 Internal Temperature Alarm



Monitors the internal temperature of the PS-B unit and the ambient temperature of the CPU. After configuring the settings via [System Setup], use the System Monitor feature to enable/disable individual monitoring features, and the monitoring levels for voltage, fan and temperature.



 Watchdog Timer Timeup



This feature monitors the performance of the CPU by writing the CPU's timeup count value from the application to the RAS feature's built-in programmable timer. Errors are detected when the writing of the count value from the application stops, which will cause a timer overflow.

Use the System Monitor Property area to set the Watchdog Timer T imeup ON or OFF, and enter detailed error processing settings.



 SMART Alarm



Monitors the status of the hard disk. Detects a warning of trouble of the hard disk.

5–2

• Administrator Authentication is required for executing SMART Monitoring.

• A CF card doesn't support SMART and therefore the status of the CF card cannot be monitored.

• When a hard disk except options made by Pro-face is used, operation of SMART Monitoring cannot be guaranteed.

PS-2000B Series User Manual

Page 78

Chapter 5 – Monitoring Features

• The SMART Monitor can be performed for the hard disk connected to

the IDE only. The state of the hard disk connected via a USB or a SCSI cannot be monitored.

• When using a Software Mirroring Utility PL-SM900 with Rev. C or

before, the SMART Monitoring can not perform.



 External Input Signals



The RAS interface connector processes the following input signals.

For connector pin arrangements and electrical specifications, refer

to 1.4.2 RAS Interface.



 General Signal Input (DIN)



General Signal Input is a general type of digital input and is used for detecting external device alarms. 4 bits (DIN0 to DIN3) are assigned for this input.

Use the System Monitor Property to turn the monitoring feature ON/OFF and enter detailed error processing settings.

The signal level of the general signal input (DIN) should be 1.5 seconds or longer; otherwise, it may not be detected.



 Remote Reset Input (RST)



This is the PS-B hardware reset signal sent from an external device. When this signal is enabled, a forced hardware reset is triggered.

Use the System Monitor Property to turn the Remote Reset Input feature ON/ OFF, and enter detailed error processing settings.



 External Output Signals



The RAS interface connector provides the following output signals.

For connector pin arrangements and electrical specifications, refer

to 1.4.2 RAS Interface.



 General Signal Output (DOUT)



General Signal Output is a digital output signal for sending system status information to external devices. 4 bits (DOUT0 to DOUT3) are assigned for this output.

This feature can be controlled from an application via the System Monitor APIDLL.

PS-2000B Series User Manual

5–3

Page 79

Chapter 5 – Monitoring Features



 Types of Processing



The PS-B unit can send the following system status information to an external device.



 LED Indicator



The two-color LED is used to indicate PS-B system conditions. It is also used as a power ON/OFF indicator. The LED is located on the front face of the PS-B unit.

LED Color System S ta tus Output Conditions

Green (Lit) Normal operation (Power ON) None Orange (Lit) A RAS alarm has occurred



 Pop-up Message Output



This feature displays system status via a Windows® pop-up message. System Monitor Property is used to enable or disable this feature.



 Buzzer Output



This feature uses the PS-B unit's built-in speaker to alert the operator about PSB system status.

LED is enabled via System Monitor Property

System Monitor Property is used to enable or disable this feature.



 System Shutdown



This feature shuts down the PS-B unit's OS. System Monitor Property is used to enable or disable this feature.



 System Reset



This feature resets the system when the Watchdog Timer reaches "time up". System Monitor Property is used to enable or disable this feature.

5–4

PS-2000B Series User Manual

Page 80

Chapter 5 – Monitoring Features

5.1.3 RAS Feature Overview

System MonitorBIOS

BIOS Setup

Voltage, Fan RPM,

Temperature Alarm

Detection Enable/Disable

System Properties

Power Alarm, Fan Alarm,

Internal Temperature Alarm,

Output Settings,

Watchdog Timer Value Settings, Watchdog Reset Enable/Disable

Popup

Message

OS Shutdown

User

Application

BIOS

Buzzer

System Alarm

Data

LED

Green: Power ON

Orange: RAS Error

System Monitoring Application

Driver or API-DLL

Watchdog

Timer

Reset Mask Settings

DIN

WDT Reset, RAS

DOUT

Reset Control

RAS Connector

DIN 4 Ports

DOUT 4 Ports

RESET IN

Hardware

Reset

Hardware

*1 Be sure to adjust these settings according to your system’s specifications.

*2 Output via the RAS feature. *3 Be sure you RAS connector’s wiring is designed for your system’s specifications.

PS-2000B Series User Manual

5.2 System Monitor/RAS Feature

1.4.2 RAS Interface

5–5

Page 81

Chapter 5 – Monitoring Features

5.2 System Monitor/RAS Features

5.2.1 Setup Procedures

Follow the steps below to enable the System Monitor/RAS features.



 Via System Monitor Setup Screen



Phoenix - AwardBIOS CMOS Setup Utility

System Monitor Setup

Shutdown Temperature [Disabled] System Warning Temperature [Disabled] CPU Warning Temperature [Disabled] Warning Voltage Vcore A [Disabled] Warning Voltage Vcore B [Disabled] Warning Voltage +3.3V [Disabled] Warning Voltage +5V [Disabled] Warning Voltage +12V [Disabled] Warning Voltage -12V [Disabled] CPU FAN Speed Limit [Disabled] Power FAN Speed Limit [Disabled]

↑↓→←: Move Enter:Select +/-/PU/PD:Value F10:Save ESC•FExit F1:General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults



 Via Applications



Item Help

Menu Level 4

Use the [System Monitor Setup] menu's System Setup screen to enable or disable monitoring features.

3.2.10 System

Monitor Setup

Start the PS-B unit's OS and start up the System Monitor Property using the [Start] ->[Programs]-> [System Monitor]->[System Monitor Property] commands. Next, set the processing to be performed when a System Monitor/RAS event occurs.

5–6

System status can be monitored at any time via the System Monitor . Select [Start] -> [Program] -> [System Monitor].

• Administrator Authentication is required for executing SMART Monitoring. When a user who does not have the administrator authentication logs in, nothing is displayed in the item of SMART.

PS-2000B Series User Manual

Page 82

Chapter 5 – Monitoring Features

5.2.2 System Monitoring Property Settings (PSB_Wps.exe)

The System Monitor Property screen allows you to configure the operating settings that are activated when system conditions exceed the allowable range (when an error occurs) of each monitoring device specified on the [System Monitor Setup] menu on the System Setup screen.

The following table lists the operating settings that can be configured for each feature.

: S et ting available x: Sett ing not available



Operation

Feature

Watchdog Timer

DIN

Voltage

Fan

Temperature

Remote Reset

Mirror Disk

SMA RT

DOUT Buzzer

    

xxxxxx

 

Popup

MessageOSShutdownOSRestart

x x x x

xxx xx

LED

   



The following table lists the description of each operation.

Item Description of the Opera tion

DOUT Output s s ignals f r om DOUT of t he RAS int erface.

Sounds a beep as an alar m. ( Cannot be se t up w hen a checkmark is put to

Buzzer

the " OS S hut dow n" checkbox. Displays error messages a s pop -up mess ages . ( The messages pop up on

Pop-up Mess age

the s creen. ) OS Shut dow n Shut s down the operating system. OS Rest ar t Restar ts the operat ing s ystem.

Select or des elect t his option to enable or disable each set t ing of the Enable

monitoring f eat ur e. LED The front or ange LE D lights

The following is the overview of the System Monitor Property setting screen.

Enable of disable the feature.

Set up the timer.

Specify the operation to be performed when the condition exceeds the allowable range.

1. The Remote Reset feature setting is selectable only between Enable and Disable.

PS-2000B Series User Manual

Enter the message to be displayed as a pop-up message.

5–7

Page 83

Chapter 5 – Monitoring Features

5.2.3 System Monitoring Operation (PSB_Smon.exe)

The System Monitor screen will not be displayed immediately after the System Monitor is started, instead, the icon will be stored in the System Tray.

When and error is detected, the "Operations (buzzer, pop-up message output, etc.)" set on the System Monitor Property are performed, and then an "X" mark appears on the icon on the System Tray, which indicates an error status. When the icon on the System Tray changes as illustrated below, double-click on the icon to review the description of the error condition.

Icon display upon start-ups

The following is the System Monitor screen.

System Monitor Screen

Icon display when an error is detected.

5–8

As for Device No. of SMART, [0] means Master and [1] means Slave.

The [Buzzer Off], [Reset], [Minimize], [Close] buttons are located at the bottom of the System Monitor screen. The following table lists the features of the buttons.

Button Operation

Buzz er Of f Stops the buzzer soun ds at normal operat ions .

Clears the err or condition held at normal operations and

Reset

inside t he S ystem Monitor. Minimize Minimize the System Monitor int o the icon display. Close Closes the Sys t em Monitor.

PS-2000B Series User Manual

Page 84

Chapter 5 – Monitoring Features

The System Monitor screen displays whether the each parameter of "FAN/TEMP/ VOLTAGE/SMART" is disabled or in normal/abnormal condition. The following table lists the status to be displayed.

Display Mea ning

No Error Normal Error Abnormal Disable Monitoring dis abled Not Suppor t Not S upport

[Not Support] is displayed when a device like a CF card, which does not support SMART, is detected.

The system performs the Error Action set in the System Monitor Property when an error condition is detected with each monitoring item, or an input from external input (Universal Input) is detected.

5.2.2 System Monitoring Property Settings

The Error Action is performed only one time when an error or input is detected for each monitoring item.

For example, look at the "+3.3 V" and "+5.0 V" options in the Voltage field. When the pop-up message feature for monitoring the voltage status is enabled, the popup message "+3.3 V Power Supply Error" appears on the screen when the +3.3 V power supply error occurs. Press the [OK] button on the dialog box to hide the message. The "+3.3 V Power Supply Error" will not appear even when a +3.3 V power supply error occurs again. However, when a +5.0 V power supply error occurs, the pop-up message "+5.0 Power Supply Error" appears on the screen. The pop-up message displays the monitored item and error description. When the buzzer feature is enabled, press the [Buzzer Off] button on the pop-up message to stop the buzzer sound. Press the [OK] button to close the pop-up message.

When "OS Shutdown" is enabled, the system automatically enters the shutdown operation without prompting the confirmation message for the user.

To display the System Monitor screen for reviewing the current condition, doubleclick on the icon on the System Tray.

When the buzzer sounds as an Error Action, the System Monitor screen displays the [Buzzer Off] button that is hidden under normal conditions. When a pop-up message window is displayed, the [Buzzer Off] button appears on the window.

PS-2000B Series User Manual

Output Screen of Pop-up Message

5–9

Page 85

Chapter 5 – Monitoring Features

Once an error is detected, the System Monitor holds the "error" status. (Displays the icon indicating the error status.) T o recover from the error status, press the [Reset] button on the System Monitor screen, of turn off the PS-B, perform maintenance service for removing the cause of the error, and then turn on the power again.

5.2.4 Error Messages

This section describes the error message and closing messages displayed on the System Monitor and System Monitor Property screens.



 System Monitor





 Error Pop-up Message



When an error occurs while the "Popup Message" option is enabled for Error Action, the following messages appears on the pop-up screen output screen under the factory-configured settings.

Error-gene ra ting I te m Messa ge

CPU Voltage "CPU Power Supply Error" CPU Voltage 2 "VIT Power Supply Error" +3.3 V Voltage "+3.3V Power Supply Error" +5.0 V Voltage "+5.0V Power Supply Error" +12 V Voltage "+ 12V Power Supply Error"

-12 V Voltage " -12V Power Supply Error" Power FA N "Power FAN Error" CPU FAN " CP U FAN Error" System Temperature "System Temperature Er ror " CPU Temperature "CPU Temperatur e Er ror " DIN0 " I nput DIN0" DIN1 " I nput DIN1" DIN2 " I nput DIN2" DIN3 " I nput DIN3" Watchdog Timer "Wat chdog Timer Error" Mirror Disk "A Mirror disk error is occurred" SMA RT "SMART Error"

The messages displayed on the pop-up message output screen can be modified on the System Monitor Property screen.

5–10



 Driver Operation Error



"The System Monitor driver not found." "Install the latest driver."



 Driver Version Error



"The old System Monitor driver version." "Update the driver ."

PS-2000B Series User Manual

Page 86



 Overlapped Startup Message



"System Monitor has started." "T erminate the System Monitor in starting."



 Closing Confirmation Message



"The System Monitor is terminated." "Are you sure?"



 System Monitor Property





 Overlapped Startup Message



"System Monitor property has started." "Terminate the System Monitor Property."



 Closing Confirmation Message



"Save Changes to the registry?"

Chapter 5 – Monitoring Features

5.2.5 Error Displays When Using Event Viewer

Error type/location and error actions are recorded as error events in the System Log. Error event information can be checked using the Event Viewer .



 Error Message Display



1) Start the [Control Panel] -> [Administrative Tools] -> [Event V iewer], and select [System Log].

2) Select the System Monitor’s error and click the [Properties] icon. When the [Event Properties] dialog box appears, the error message will appear in the [Description] area.

PS-2000B Series User Manual

5–11

Page 87

Chapter 5 – Monitoring Features



 Error Type/Location



The error types/locations shown by the Event Viewer are as follows.

Error Ty pe/Location Error M e ss a ge

+3. 3V +3.3V Error has occurred. +5. 0V +5.0V Error has occurred. +12V +12V Error has occurred.

-12V -12V Error has occurred. CPU voltage CPU v oltage E rr or has occurred. Vit volta CPU FA N CPU FAN Error has occurred. Power FA N Power FAN Error has occurred. CPU Temp CPU Temperature Error has occurred. S DIN0 DIN0 input has occurred. DIN1 DIN1 input has occurred. DIN2 DIN2 input has occurred. DIN3 DIN3 input has occurred. Watch Do Backli Soft Mirror Mirror Disk Error has occurred. SMART SMA RT Error has occurred. A t t ribute (No.) (A tt ribute Name)

eVit valta

stem Temp System Temperatur e Er ror has occurred.

Ti mer W atch D og Timer Error has occurred.

ht Backlight Error has occurred.

Device (No.) (HD Model). The descriptions in the parent heses vary depending on details of occurring errors and the device having errors occur (0:Master,1:Slav e) .

e Error has occurred.



 Error Action



Using the Event Viewer the following actions can be taken when an error occurs.

• The data shown in the table’s “” indicate the error type/location.

• The actions to take after an error occurs are set via the System Monitor Property screen.

Error Ac ti on Error M e ss a ge

Buzzer Buzzer has sounded because of  error. Popup Messa OS Shut down Windows has been shut down because of  error. LED LED has changed to o range because of  error. DOUT0 DOUT0 has output because of  error. DOUT1 DOUT1 has output because of  error.

DOUT2 DOUT2 has output because of  error. DOUT3 DOUT3 has output because of  error.

e Popup message has been shown because of  error.

When a “+3.3V” error occurs and the buzzer sounds, two errors will be displayed, “+3.3V Error has occurred.” and “Buzzer has sounded because of +3.3V error”.

5–12

PS-2000B Series User Manual

Page 88

Chapter 5 – Monitoring Features

5.3 Remote RAS

The Remote RAS feature uses the Pro-face's Pro-Server with Pro-Studio (optional) installed in the host PC to monitor and control the System Monitor/RAS feature of the PS-B.

Pro-Server with Pro-Studio Ver.3.12 of higher is required to use the Remote RAS feature. When using this feature, refer to the installation guides provided with the Pro-Server as well as this manual.

5.3.1 System Configuration

The system employing this feature is configured as illustrated below.

Two-way feature

Client PS-B

Server PC

Ethernet

User Application

Pro-Server with Pro-Studio Ver.3.12 or higher Remote RAS Server Program (PSB_RAS.npj)

[System Monitor/RAS Feature]

• PSB_Smon.exe

• PSB_Wps.exe

• PSB_loc.dll

• PSB_DLL.dll

• PSB_Ras.dll

• PSSymon.sys

5.3.2 Installation Procedures

On the server PC, start up the "Setup.exe" file in the [RASSvr] folder on the accessory CD-ROM, and then install the program by following the instructions on the screen.

PS-2000B Series User Manual

5–13

Page 89

Chapter 5 – Monitoring Features

5.3.3 Setup and Preparation of the Remote RAS Feature

In order to monitor the System Monitor/RAS features from the server PC, you are required to set up the Remote RAS feature and start up the System Monitor (PSB_Smon.exe).



 Setting Up the Client PS-B



(1) Select [Start] → [Programs] → [System Monitor] → [System Monitor Prop-

erty] commands to start the System Monitor Property.

(2) On the [Remote Ras] tab, put a check mark to the [Enable] checkbox.

IP Address used to connect with Pro-Server

This feature designates that the PS-B will communicate only with the server at the specified IP address.

Put check marks on the items you want to monitor.

Specify the IP address of the server you want to communicate with.

The Remote RAS feature is now enabled.

In order to actually activate the Remote RAS feature, you are required to start up the System Monitor (PSB_Smon.exe) within the PS-B.



 Setting Up the Server PC



(1) Start up the Pro-Studio. (2) Register the PS-B you want to include in the network to the network station,

and edit the participant stations.

Pro-Server with Pro-Studio for Windows Operation Manual

When using the Pro-studio’s [Find Stations] command to register the PS-B to the network station, the System Monitor should be activated with the Remote RAS feature enabled in the PSB.

(3) Select [PL, PS-B] for the PLC type on the network station editing. (4) When registering the symbol, refer to the List of Device Address for the

symbol that can be registered.

5–14

*1 When allocating 2 or more IP Addresses to the PS-B unit, [Auto] cannot be selected.

Enter settings that allow the reading of a fixed IP Address from a DHCP server. For details, contact your company’s network administrator.

PS-2000B Series User Manual

Page 90

Chapter 5 – Monitoring Features

Y ou are not required to transfer the network project file created with the Pro-Studio to the client PS-B.

5.3.4 Read and Write of the System Monitor/RAS Feature

The read/write operation of the operating conditions of the client PS-B and System Monitor/RAS feature can be performed from the server PC via the Pro-Server.

Server PC

User Application

Pro-Server with ProStudio (Optional)

Pro-Easy.dll

Ethernet

Two-Way feature

Client PS-B

User Application

PSB_Ras.dll

PSB_Smon.exe

Shared Memory

• The status of the System Monitor/RAS feature is stored in the shared memory for which device address is assigned.

n List of Device Addresses /n Bit Assign of DIN, Error Event,

and Error Mask

• The status of the System Monitor/RAS feature is transferred to the Pro-Server via Ethernet from the PSB_Smon.exe. The RAS feature including voltage, FAN, and temperature can be monitored by monitoring the device addresses assigned from the Pro-Studio.

• The user applications in the server PC monitors the RAS feature through the Pro-Easy.dll program provided from the Pro-Server.

• The client PS-B shares the data with the user applications on the server PC by using the shared memory. The data transfers on both sides are processed via the PSB_Ras.dll and Pro-Easy.dll programs.

• The client PS-B can be shut down and re-started by writing specific value to the software reset port.

PS-2000B Series User Manual

5–15

Page 91

Chapter 5 – Monitoring Features

For the details of Read/Write to the devices and access procedures, refer to the "List of Device Addresses" below.



 List of Device Addresses



Device

CPU Voltage

+3.3V V olt age

+5V Voltage

+12V V olt age

-5V Voltage

-12V Volt age VIT Voltage

*1*7

Device

Type

WORD VLT0 WORD VLT1 WORD VLT2

WORD VLT3 WORD VLT4

WORD VLT5 WORD VLT6

Device

Symbol

VLT

Read/

Write

READ

Bit Access

—

Number of Rev olution of

CPU FAN

WORD FAN0

FAN

Number of Rev olution of

Power FAN

CPU Temperature

System Temperature

WORD FAN1

WORD TMP0

WORD TMP1

TMP

DIN WORD DIN DIN00-DIN01 DIN0

Read/

DOUT WORD DOUT

DOUT00 DOUT0

Write

Error E vent WORD ERR Read ERR00-E RR0E ERR0

Internal Memory Area

WORD LS

LS00000-LS0000F to

LS02550-LS0255F

Read/

PL00000-PL0000F to

S h ared Memory WORD PL

Write

PL02550-PL0255F

Software Reset Port

Error Mask

WORD RST — RST0 — WORD ERRM Read ERRM00-ERRM0E ERRM0 —

16-bit

Access

LS0000 to

LS0255

PL0000 to

PL0255

32-bit

Access

—

LS0000 to

LS0254

PL0000 to

PLS0254

5–16

1. When monitoring the voltage with the device monitor, the unit is "mV".

2. When monitoring the voltage with the device monitor, the unit is "rpm".

3. When monitoring the voltage with the device monitor, the unit is "°C".

4. Used for the system to read/write the data and perform monitoring operation.

5. Shuts down and restarts the operation system on the client PS-B.

6. Indicates the error event that is being monitored by the PS-B.

7. -5V Voltage is ffff(hex), 65535 (decimal).

PS-2000B Series User Manual

Page 92

Chapter 5 – Monitoring Features

When "Forced Shutdown" or "Forced Reboot" is written to the device address, the system automatically shuts down/restarts the operation system without prompting the confirmation for saving the data on current applications. Take extra cautions when performing write operation in order to avoid accidental data loss.

Value to be W ritte n

Decimal Number Hexadecimal Number

1 0001 Shutdown

2 0002 Reboot 257 0101 Forced Shutdown 258 0102 Forced Reboot



 Bit Assign of DIN, Error Event, and Error Mask



De v ice Name Item Bit

DIN0 DIN00

DIN

+3.3 V Voltage Errorr ERR01

+12 V Voltage Errorr ERR03

Error Ev ent

CPU Temperature Err orr ERR09

System Temperature ERR0A

Watchdog Timer Errorr ERR0B

+3. 3 V Volt age E rr orr ERRM01

Error Mask

CPU Temperature Err or ERRM09

System Temperature ERRM0A

Watchdog Timer Error ERRM0B

DIN1 DIN01 DIN2 DIN02 DIN3 DIN03

CPU Voltage Error ERR00

+5 V Voltage Errorr ERR02

-5 V Voltage Errorr ERR04

-12 V Voltage Errorr ERR05 V I T Voltage Errorr ERR06

CPU FAN Errorr ERR07

Power FAN Errorr ERR08

Mirror Disk Error ERR0C

SMART Errorr ERR0D

CPU Voltage Error ERRM00

+5 V Voltage Error ERRM02

+12 V Voltage Error ERRM03

-5 V Voltage Error ERRM04

-12 V Voltage Error ERRM05 VIT Voltage Error ERRM06

CPU FAN Error ERRM07

Power FAN Error ERRM08

Mirror Disk Error ERRM0C

SMART Errorr ERRM0D

Operation

PS-2000B Series User Manual

5–17

Page 93

Chapter 5 – Monitoring Features



 Error Messages



This section describes the error messages of the Pro-Server that are displayed for the errors caused during device read/write operations. The following table lists the error codes for the RAS feature.

Error Code

Decimal

Number

9530 253A h RAS I nit ialization Error 9531 253Bh Command not supported. 9532 253Ch A ccess t ype not support ed. 9533 253Dh Read/ Write type not s uppor ted. 9534 253Eh Access to the device rejected. 9535 253Fh V alue setting to the device/ret r ieval failed.

65535

(No Code)

Hexadecimal

Number

ffffh

Returned when read/ wr ite of invalid values or uns upport ed dev ice is performed for Voltage, Temperature, and number of revolution of the FAN.

Error M essag e

For error messages other than listed above, r efer to "Pro-Server with

Pro-Studio for Windows Operation Manual".

5.3.5 Restrictions

The following table lists the features of Pro-Server that are supported by the PS-B. For the details of each feature, refer to "Pro-Server with Pro-Studio for Windows Operation Manual".

: Supported

Pro-Server Feature

DDE Feat ure

Simplified DLL Feature (ProE asy.dll) List ed Separately

OPC Server Interface

SRAM Backup Data x

Action Featur e x

Distribut ion Featur e x

Data Viewer

V BA Feature A ssist

Device Data Backup/Restore Feature

Capture S creen Save Feature x

Security Feature

Device Monitor

St at us Monitor x

Read Time Measurement



x: Not Supporte d



 



5–18

1. Pro-Server with Pro-Studio Ver.4.0 or higher is required.

PS-2000B Series User Manual

Page 94

Chapter 5 – Monitoring Features

• Direct Read Feature

• Direct W rite Feature

• Cache Read Feature

• Retrieval of Multithreading Handle

• Release of Multithreading Handle

• Loading of Network Project File

• Error Code String Conversion

• Station Status Readout Feature

• Initialization of Simplified DLL

• Termination of Simplified DLL

• Note that the PS-B-supported OS and features supported by Pro-Server are different.

• The Remote RAS feature and Pro-Server cannot be operated simultaneously on the PS-B.

5.4 Remote Shutdown Feature

The Remote Shutdown feature allows the user to shut down and/or restart the PSB from the server PC via the network when the Pro-Server is not installed to the system. The installer of this application is included on the accessory CD-ROM (\Utility\Shutdown).

When the installer is started, you are asked to select the application for server or the client. Select the desired application, and follow the instruction on the screen to complete the installation.

File Nam e Fol der (Sam e for both Window sXP and Windows2000)

PSClt.exe C:\Proface\Shutdown\Client RSSvr.exe C:\Proface\Shutdo wn \Server

4.1.1 Software

• For the operation procedure of this feature, refer to the online help of the Remote Shutdown Application.

• Both applications (for server and client) can be installed on the PS-B to achieve self-control system. In such a case, however, the PS-B should be connected to a network.

PS-2000B Series User Manual

5–19

Page 95

Chapter 5 – Monitoring Features

Memo

5–20

PS-2000B Series User Manual

Page 96

Chapter 6 – Maintenance and Inspection

Chapter

6 Maintenance and Inspection

This chapter describes the cautions and inspection criteria for ensuring comfort and safety in operating the PS-B.

6.1 Cleaning the Fan Filter

A fan is installed to the PS-B for cooling the unit. Be sure to periodically perform inspection and cleaning of the fan, since dust accumulated on the fan filter will affect the cooling performance of the fan.

1. Cleaning the Fan Filter

2. Periodical Inspections

Procedure

Remove the screws (2) on the filter cover and filter cover, and then remove the filter.

Clean the filter by using vacuum cleaner to remove the dust accumulated on the filter. Set the filter to the original position, and then reattach the filter cover and filter cover mounting screws.

If stubborn dust or stains persist, wash the filter with neutral detergent and rinse it thoroughly with water.

• Do not wring the water out of the filter.

• Dry the filter in the shade and do not leave it in the direct sunlight.

• Wait until the filter is completely dry, and then reattach to the main unit.

Filter Cover

Filter

PS-2000B Series User Manual

Filter

6–1

Page 97

Chapter 6 – Maintenance and Inspection

6.2 Periodic Maintenance Points

Check the PS-B periodically to ensure it is in good working condition.



 Ambient environment check



Is the ambient temperature within the specified range?

With HDD, FDD Without HDD, FDD

5 to 50°C 0 to 50°C

 Is the ambient humidity within the specified range (10%RH to 85%RH)?  Is the atmosphere free of corrosive gas?



 Electrical specifications check



 Is the voltage adequate (AC85V to AC265V, 50/60 Hz)?



 Installation check



 Are all cables securely connected (not loose)?  Have any of the PS-B unit’s installation brackets become loose?

6–2

PS-2000B Series User Manual

Page 98

Chapter 7 – Specifications

Chapter

7 Specifications

7.1 General Specifications

7.1.1 Electrical Specifications

Rated Voltage AC100V/A C240V Allowable V olt age Range AC85V to AC265V Rated Fr equency 50/60 Hz

1 cycl e max.

Allowable Volt age Drop

(Note: Intervals between instantaneous outage should be 1 s or longer.)

Power Consumption 110 V A max.

AC 1500V , 20 mA per minute

Insulat ion Endurance

(Bet ween t he charging and FG terminals)

Insulation Resistance 10 MΩ min. at DC 500V (Between the charging and FG terminals)

1. General Specifications

2. Performance Specifications

PS-2000B Series User Manual

7–1

Page 99

Chapter 7 – Specifications

7.1.2 Environmental Specifications

Ambient Temperature (Interior)

5 to 50°C (With HDD) 0 to 50°C (Without HDD)

St orage Temperature -10 to +60°C

10 to 85%RH

Relative Humidity

(No condensation, wet -bulb t emperature of 29°C max. ) 10 to 85%RH

St orage Humidity

(No condensation, wet -bulb t emperature of 29°C max. ) Dust No dust or dirt s hould be pres ent . Pollution Level Pollut ion level 2 Corrosive Gas No corrosive gas should be present.

Vibration Resistance

9.8 m/s

With HDD attached: 4.9 m/s

(10 to 25 Hz, withstands for 30 minutes in X/Y/Z directions)

Noise Voltage: 1500 V Noise Resistance

Pulse W idt h: 50 ns, 500 ns, 1 µs (Impulse Noise)

Rise Time: 1 ns (By noise simulator) Antistatic Charge 6 kV, I E C 61000- 4- 2

No i se I mmu n i ty (The first transient burs t noise)

Power Line: 2 kV , IEC 61000-4-4

COM Port : 1 kV, IEC 61000-4-4

• When using optional equipment, be sure to check the specifications for the equipment.

• The hard disk drive is a consumable item. It is recommended to prepare for product malfunction by making periodical backups of the data and preparing replacement HDD unit.

• The operation life of a hard disk drive varies depending on the use environment and conditions; however, it is approximately 20,000 hours (of operation time) under ambient temperature of 20°C or 5 years, whichever comes first.

• Operating the hard disk under harsh environment of high temperature and high humidity will shorten the operating life. It is recommended to operate the HDD at wet-bulb temperature of 29°C or lower. The condition is equivalent of 35°C with 64%RH, or 40°C with 44%RH.

7.1.3 External Specifications

Grounding St r ucture Installation Method: In-cabin inst allation

Coolin Wei

External Dimensions With CD-ROM/FD Drive unit

attac h ed With RS-23 2 C/RS-485 Conversion Unit attached

Method Cooling by main unit fan and CP U fan

ht Approx. 4.5 kg (Main unit onl

Protective grounding: D-type grounding Functional grounding: D-type grounding

118 (W) x 265 (H) x 299 (D) mm (Not including pr oj ections) 159 (W) x 265 (H) x 299 (D) mm (Not including pr oj ections)

139.5 ( W) x 265 (H) x 299 ( D) mm (Not including cables and projections)

7–2

PS-2000B Series User Manual

Page 100

Chapter 7 – Specifications

7.2 Performance Specifications

7.2.1 Performance Specifications

CPU DRA M (SDRAM DIMM) BIOS Secondary Cache Memory

Graphics

Video Memory Video I/ F

Serial (RS232C)

USB (USB1.1) LAN

Disk Drives

Keyboard Mouse RAS Sound

Celeron

566 MHz / P entium® II I 1GHz (BUS 100MHz) (Int el) DIMM socket x 1: 128 MB/256 MB (256 MB max.) First BI OS (P hoenix Technologies Co.) Built int o CPU ( Celeron: 128 KB , P ent iumII I : 256K B)

VGA ( 640 x 480 dot s ) to UXGA (1600 x 1200 dot s) VESA 256 colors/16-bit color/32-bit color

4 MB fixed (UMA ty pe) Analog RGB I/F

DV I-D I/F COM1 D-sub 9 pin (male), ( RI/+5 V selectable) COM2 D-sub 9 pin (male) COM3 D-sub 9 pin (male), ( RI/+5 V selectable) COM4 D-sub 9 pin (male) Front face: 4 ports

IEEE802.3 compatible (10 Base-T/100 Base-TX automatic changeover) Front face: 2 ports

For 2-mode 3.5 inch floppy dis k I /F Inter nal: 1 port

FD I/F

(for Digit al Electronics Corporation' s CD-ROM/FD drive unit) For built- in primary HDD I/F Int er nal: 2 po rts

IDE I/F

For secondary CD-ROM I/F Internal: 1 port (for Digit al Electronics Corporation' s CD-ROM/FD

drive unit) PS/2 I/F (Mini-DI N 6 pin, female), Fro nt f ace: 1 port PS/2 I/F (Mini-DI N 6 pin, female), Fro nt f ace: 1 port RA S I / F (D-s ub 25 pin, male) Front f ace: 1 port LINE IN, SPEAKER OUT, MIC IN(Standard type A UDIO jack)

• The PS-B unit’s CPU and DRAM are user-selectable when the unit is purchased.

• Be sure to use SVGA (800 x 600 dots) or higher, 16-bit display colors or higher resolution when using Windows

1. The display resolution used must be supported by the PS-B unit’s OS, applications and the external display unit.

2. 1600 x 1200 dots: Up to 256 colors

PS-2000B Series User Manual

XP.

7–3

Pro-face PS-2000B Series User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Preface

TABLE OF CONTENTS

Essential Safety Precautions

Documentation Conventions

Package Contents

UL/c-UL (CSA) Application Notes

CE Marking Notes

1.1 Prior to Operating the PS-B Unit

1.2 PS-B System Design

1.3 PS-B Part Names and Features

1.4 Interfaces

1.4.1 RS-232C Interface (COM1/COM2/COM3/COM4)

1.4.2 RAS Interface (RAS)

1.4.3 DVI-D Interface

1.5 PS-B External Views and Dimensions

1.5.1 PS-B Unit

1.5.2 With CD-ROM/FDD Unit Attached

1.5.3 With RS-232C/RS-485 Conversion Unit Attached

1.5.4 With Mounting Bracket Attached

2.2 Installing the PS-B Unit

2.2.1 PS-B Unit Installation Cautions

2.2.2 Installation Procedures

2.3 Wiring

2.3.1 Connecting the Power Cord

2.3.2 Power Supply Precautions

2.3.3 Grounding Precautions

2.3.4 Precautions When Connecting I/O Signal Lines

3.1 Setup Procedures

3.2 System Parameters

3.2.1 Standard CMOS Features

3.2.2 IDE HDD Auto-Detection

3.2.3 Advanced BIOS Features

3.2.4 Advanced Chipset Features

3.2.5 Integrated Peripherals

3.2.6 Power Management Setup

3.2.7 PnP/PCI Configurations

3.2.8 IRQ Resources

3.2.9 DMA Resources

3.2.10 System Monitor Setup

3.2.11 Frequency/Voltage Control

3.2.12 Load Fail-Safe Defaults

3.2.13 Load Optimized Defaults

3.2.14 Set Supervisor Password

3.2.15 Set User Password

3.2.16 Save & Exit Setup

3.2.17 Exit Without Saving

4.1 CD-ROM Contents

4.1.1 Software

4.2 Setting up Your PS-B Unit

4.2.1 Setup Procedures

4.2.2 Setting Up an HDD with Pre-installed OS

4.3 Installing Drivers

4.4 Special Application Program Features

4.4.1 Uninstalling Utility Software

4.5.1 Automatic System Log-on Setup

4.5.2 Uninterrupted Power Supply System (UPS)

4.5.3 Changing System Settings

4.5.4 NTFS File System Conversion

5.1 RAS Features

5.1.1 PS-B RAS Features

5.1.2 RAS Feature Details

5.1.3 RAS Feature Overview

5.2 System Monitor/RAS Features

5.2.1 Setup Procedures

5.2.2 System Monitoring Property Settings (PSB_Wps.exe)

5.2.3 System Monitoring Operation (PSB_Smon.exe)

5.2.4 Error Messages

5.2.5 Error Displays When Using Event Viewer

5.3 Remote RAS

5.3.1 System Configuration

5.3.2 Installation Procedures

5.3.3 Setup and Preparation of the Remote RAS Feature

5.3.4 Read and Write of the System Monitor/RAS Feature

5.3.5 Restrictions

5.4 Remote Shutdown Feature

6.1 Cleaning the Fan Filter