1
PRESTIGIO P1710
ENG
Before operating the monitor please read this manual thoroughly.
This manual should be retained for future reference.
NOTE: This specification is subject to change without notices.
FOR YOUR SAFETY
FCC Class B Radio Frequency Interference Statement
WARNING:(FOR FCC CERTIFIED MODELS)
NOTE:This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced electric technician for help.
NOTICE
1. The changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
2. The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modification to this equipment. It is the responsibilities of the user to correct such interference.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerous high voltages are present inside
the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.
PRECAUTIONS
• Do not use the monitor near water, or lay it at a moisture place.
• Openings in the back of the cabinet are provided for ventilation. To ensure reliable operation of the monitor and to
protect it from overheating, be sure these openings are not blocked or covered.
• The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the
type of power supplied to your home, consult your dealer or local power company.
• Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the
monitor from damage due to power surges.
• Do not overload the wall outlets and extend cords. Overloading can result in fire or electric shock.
• Do not attempt to service the monitor by yourself, opening or removing covers can expose you to dangerous voltages
and other hazards. Please refer all servicing to qualified service personnel.
2
PRESTIGIO P1710
ENG
• To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured
receptacles marked between 100-240V AC, Min. 1.2A.
• The wall socket shall be installed near the equipment and shall be easily accessible.
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a problem.
NOTES
• Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then
turn it on again to make sure the flicker disappears. Or you can use of AUTO function.
• You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
• The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a missing pixel
or a pixel lit all of the time.
• Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when
the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image or turning off the
Power Switch for hours.
• The life of the fluorescent light used in the LCD monitor is approximately 50,000 hours. Contact your dealer for
replacement when the screen is dark, flickering or not lighting up. Never attempt to replace it by yourself.
BEFORE YOU OPERATE THE MONITOR
FEATURES
• 43.2cm(17”) TFT Color LCD Monitor
• Crisp, Clear Display for Windows
• Recommend Resolutions:1280 X 1024 @75Hz
• EPA ENERGY STAR
• Space Saving, Compact Case Design
POWERCORD
Power Source:
1. Make sure the power cord is the correct type that required in your area.
2. This LCD monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area
(No user adjustment is required.)
3. Connec t the AC-power cord into your LCD monitor’s External Adapter input socket, and then plug the other end of
External adapter to LCD monitor’s DC-power-input. The AC-power cord may be connected to either a wall power outlet
or the power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor.
3
PRESTIGIO P1710
ENG
CONTROLS AND CONNECTORS
VIDEO CABLE
Connecting the Video Cable:
Plug one of the signal cable’s 15-pin connector into the Computer’s video port and tighten the two screws on the cable
connector. Then plug the other 15-pin connector into the LCD’s video port, and tighten the two screws on the cable
connector.
Connecting the Audio Cable:
Plug one of the signal cable’s 15-pin connector into the Computer’s audio port and tighten the two screws on the cable
connector. Then plug the other 15-pin connector into theAudio signal inlet.
Plug the AC-power cord into the External Adapter. Then plug the DC-jack power cable into DC-IN Inlet. According to the
type of the power code which suit with the LCD monitor.
ADJUSTING THE VIEWING ANGLE
• For optimal viewing it is recommended to look at the full face of the monitor, then adjusting the monitor’s angle to
your own preference.
• Hold the stand so you do not topple the monitor when you change the monitor’s angle.
• You are able to adjust the monitor’s angle from 5°to 15°.
NOTES
• Do not touch the LCD screen when you change. It may cause damage or break the LCD screen.
• Careful attention is required not to catch your fingers or hands when you change the angle.
4
PRESTIGIO P1710
ENG
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power switch to turn the monitor on or off. The other control knobs are located at front panel of the monitor. By
changing these settings, the picture can be adjusted to your personal preferences.
• The power cord should be connected.
• Connect the video cable from the monitor to the video card.
• Press the power switch to turn on the monitor position. The power indicator LED will light up.
FRONT PANEL CONTROL
• Auto Adjust Key:
When OSD menu is in off status, press this button direct to activate the Auto adjustment function.
The Auto Adjustment function is used to set the Hpos, Vpos, Clock and Focus.
• Brightness <:
Adjust brightness or adjust function
• Contrast >:
Adjust contrast or adjust function.
• MENU :
Activate the OSD menu or confirm the function adjusting.
• Power Key:
Press this button to switch ON/OFF of monitor’s power.
• Power Indicator:
Blue - Power On mode.
Orange - Off mode.
NOTES
• Do not install the monitor in a location near heat sources such as radiators or air ducts, or in a place subject to direct
sunlight, or excessive dust or mechanical vibration or shock.
• Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your
monitor.
• For maximum protection, repackage your monitor as it was originally packed at the factory.
• To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth
lightly dampened with a mild detergent solution. Never use strong solvents such as thinner, benzene, or abrasive cleaners,
since these will damage the cabinet. As a safety precaution, always unplug the monitor before cleaning it.
5
PRESTIGIO P1710
ENG
HOW TO ADJUST A SETTING
1.Press the MENU button to activate the OSD window.
2.Press > or < to select the desired function, then press the MENU button again.
3.Press > or < to change the settings of the current function ,press the MENU button to confirm it.
4. If you want to adjust any other function, repeat steps 2-3.
5.If you want to exit the OSD image, select the “exit function/EXIT OSD”, or leave the monitor alone for 20 seconds
(Windows default), the OSD window will close and sure automatically.
6. When the OSD window is active, it shows the input signal timing.
ADJUSTING THE PICTURE
1. AUTO SETTING
1.1AUTO GAIN CONTROL
Adjust the gain automatically.
1.2 BRIGHTNESS
Adjust the brightness automatically.
1.3 CONTRAST
Adjust the contrast automatically.
1.4 EXIT
2. COLOR
2.1 AUTO COLOR
Adjust the color automatically.
2.2 Exit
3. IMAGE
3.1 AUTO CONFIGURATION
Adjust the image position.
3.2CLOCK
Adjust the image clock.
3.3PHASE
Adjust the image focus
3.4H-Position
Adjust the image horizontal position
3.5V-Position
Adjust the image vertical position.
3.6Exit
4. TOOLS
4.1OSD TIMEOUT
Control the quit time of quit the OSD menu automatically.
4.2 OSD H.Position
Adjust the horizontal position of OSD menu.
6
PRESTIGIO P1710
ENG
4.3 OSD V.-Position
Adjust the vertical position of OSD menu.
4.4 VOLUME
Adjust the volume of the speaker.
4.5 FACTORY REST
Recall to factory setting
4.6 EXIT
5. COLOR TEMP
selection 5000k warm
6500k standard
9300k cool
If 5000k,6500k, 9300k can’t meet your need, you can do like this adjust the red ,green and blue pluses through userdefined menu.
6. LANGUAGE
Choose the language of OSD menu, you can choose English, Czech, Russia, German, Polish etc.
7. EXIT
Exit OSD menu.
HOW TO OPTIMIZE THE DOS-MODE
1. Get the full screen pattern at MS-DOS mode, type in C:\>EDIT [press enter] You will be in the Dos-Editor screen
2. Press“AUTO”button(at front pane) about 2 seconds, the monitor will do all the adjustment automatically. You can
adjust the image manually, if the screen has a flicker or blur, or not fit in the display
3. press ALT-F, and then X to exit from the Dos-Editor screen
If the DOS-MODE characters still have distortion
Example:
• The picture can’t go to full screen
• The background of white pattern has vertical stripe noise
• The character twisted
That means your monitor parameter was in wrong resolution, please check if your VGA-CARD supports 720x400@70Hz
Generally speaking, most of the Dos mode was set by VGA-CARD in resolution 720x400@70Hz, but minor was set in
640x400@70Hz
7
PRESTIGIO P1710
ENG
PLUG AND PLAY
Plug & Play DDC1/2B Feature
This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor
to inform the host system of its identity, and depending on the level of DDC used, communicate additional information
about its display capabilities. The communication channel is defined in two levels, DDC1 and DDC2B.
The DDC1 is a unidirectional data channel from the display to the host that continuously transmits EDID information. The
DDC2B is a bidirectional data channel based on the I2C protocol. The host can request EDID information over the DDC2B
channel.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO INPUT SIGNAL. IN
ORDER FOR THIS MONITOR TO BE PROPERLY OPERATED, THERE MUST BE A VIDEO INPUT SIGNAL.
This monitor meets the Green monitor standards as set by the Video Electronics Standards Association (VESA) and/or the
United States Environmental Protection Agency (EPA) and The Swedish Confederation Employees (NUTEK). This feature is
designed to conserve electrical energy by reducing power consumption when there is no video-input signal present. When
there is no video input signal this monitor, following a time-out period, will automatically switch to an OFF mode. This reduces
the monitor’s internal power supply consumption. After the video input signal is restored, full power is restored and the
display is automatically redrawn. The appearance is similar to a “Screen Saver” feature except the display is completely off.
The display is restored by pressing a key on the keyboard, or clicking the mouse.
8
PRESTIGIO P1710
ENG
TECHNICAL SUPPORT (FAQ)
Problem & Question Possible Solution
Power LED is not on Check if the Power Switch is in the ON position
Power Cord should be connected
No Plug & Play Check if the PC system is Plug & Play compatible
Check if the Video Card is Plug & Play compatible
Check if the D-15 plug pin of Video
Cable is bent
Picture is fuzzy Adjust the Contrast and Brightness Controls.
Picture bounces or a wave pattern Move electrical devices that may cause electrical interference.
is present in the picture
The power LED is ON (Red) Computer Power Switch should be in the ON position.
but there’s no video or no picture. Computer Video Card should be snugly seated in its slot
Make sure monitor’s video cable is properly connected to the computer.
Inspect monitor’s video cable and make sure none of the pins are bent.
Make sure computer is operational by hitting the CAPS LOCK key on the keyboard
while observing the CAPS LOCK LED. The LED should either turn ON or OFF after
hitting the CAPS LOCK key.
Missing one of the primary Inspect the monitor’s video cable and make sure that none of the pins are bent.
colors(RED,GREEN,or BLUE)
Screen image is not centered Adjust pixel frequency(CLOCK) and PHASE or press hot-key (AUTO)
or sized properly.
Picture has color defects Adjust RGB color or select color temperature
(white does not look white)
Poor brightness or contrast The life time of the back-light is limited. In 30000 Hours the luminance of the
light has been reduced to half of its original value. Please send the monitor to an
authorized service Agent for service.
Horizontal or vertical disturbancies Use win 95/98/2000/XP shut-down mode Adjust CLOCK and PHASE or perform hoton the screen key (AUTO-key).
CLOCK (pixel frequency) controls the number of pixels scaned by one horizontal sweep. If the frequency is not correct, the
screen shows vertical stripes and the picture has not correct width.
PHASE adjust the phase of the pixel clock signal. With a wrong phase adjustment the picture has horizontal disturbances in
light picture.
For PHASE and CLOCK adjustment use “dot-pattern” or win 95/98/2000/XP shut-down mode pattern.
9
PRESTIGIO P1710
ENG
ERROR MESSAGE AND POSSIBLE SOLUTION
CABLE NOT CONNECTED:
1. Check that the signal-cable is properly connected. If the connector is loose, tighten the connector’s screws.
2. Check the signal-cable’s connection pins for damage.
INPUT NOT SUPPORTED:
Your computer has been set to unsuitable display mode. Set the computer to display mode given in the following table.
UNSUPPORTED MODE, TRY DIFFERENT VIDEO CARD SETTING:
Your computer resolution is out of VESA-SPEC
RESOLUTION:
RESOLUTION VERTICAL FREQUENCY RESOLUTION VERTICAL FREQUENCY
640×480 60Hz 800×600 75Hz
720×400 70Hz 1024×768 60Hz
640×480 72Hz 1024×768 70Hz
640×480 75Hz 1024×768 75Hz
800×600 56Hz 1280×1024 60Hz
800×600 60Hz 1280×1024 75Hz
800×600 72hz
FACTORY PRESET TIMING TABLE
STANDARD RESOLUTION HORIZONTAL FREQUENCY VERTICAL FREQUENCY
VG A 720×400 31.47 kHz 70.00 Hz
640×480 31.469 kHz 60.00 Hz
640×480 37.861 kHz 72.00 Hz
640×480 37.5 kHz 75.00 Hz
SVGA 800×600 35.156 kHz 56.00 Hz
800×600 37.879 kHz 60.00 Hz
800×600 48.077 kHz 72.00 Hz
800×600 46.875 kHz 75.00 Hz
XGA 1024×768 48.363 kHz 60.00 Hz
1024×768 56.476 kHz 70.00 Hz
1024×768 60.023 kHz 75.00 Hz
SXGA 1280×1024 63.981kHz 60.020Hz
1280×1024 79.976kHz 75.025Hz
10
PRESTIGIO P1710
ENG
CONNECTOR PIN ASSIGNMENT FOR VGA SIGNAL INPUT
PIN NO. DESCRIPTION
1. Red
2. Green
3. Blue
4. NC
5. Ground
6. R-Ground
7. G-Ground
8. B-Ground
PIN NO. DESCRIPTION
9. NC
10. Ground
11. NC
12. DDC-Serial Data
13. H-Sync
14. V-Sync
15. DDC-Serial Clock
11
PRESTIGIO P1710
ENG
SPECIFICATIONS
Basic Parameter
LCD Panel Driving system TFT Color LCD
Size 43.2cm(17”)
Pixel pitch 0.264mm(H)×0.264mm(V)
Display Colors 16M
Max .Resolution 1280X1024 @75Hz
Plug & Play VESA DDC1/2BTM
Maximum Screen Size Horizontal:13.3’(337.9mm)
Vertical:10.6’(270.3mm)
Environmental Considerations Operating Temp: 0°C to 40°C
Storage Temp:-20°C to 60°C
Operating Humidity: 10% to 80%.
External Controls Switch Auto Adjust Key/ Exit
Brightness
Contrast
Menu/Enter
Power Key
Functions Brightness
Contrast
Color
Language
Auto Adjust
Exit
Factory Reset
EPA Energy Star ON Mode <40W(For 2 CCFL)
OFF Mode <3W
Regulatory Compliance FCC, CB, CE, UL
Chief Parameter (Different parameter with different model)
Viewable angle (Horizontal/Vertical) 140°/130°
Response time 8ms
Contrast 500:1
Brightness 300 cd/m
2
12
PRESTIGIO P1710
ENG
CHECKING THE CONTENTS OF THE PACKAGE
The product package should include the following items:
1. LCD Monitor 1 set
2. Owner's Manual 1 pcs
3.Power Cord 1 pcs
4.VGA signal cable 1pcs
5. Audio cable 1 pcs
6.Adapter 1 pcs
Loading...