Premier WP-4, KP-4, WP4-50, RO-4M Installation, Operation And Maintenance Manual

Download

Page 1

INSTALLATION, OPERATION AND MAINTENANCE MANUAL

Please read carefully before proceeding with installation. Your failure to follow any attached instructions

or operating parameters may lead to the products failure and possible damage to property.

Warning

Save manual for future reference

MODEL

WP-4 WP4-50 KP-4 RO-4M

System Tested and certiﬁ ed by WQA against NSF/ANSI Standard 58 for the reduction of the claims speciﬁ ed on the performance data sheet.

Refer to enclosed warranty for operating parameters to ensure proper use with your water supply.

Premier, Inc. 8716 W Ludlow Drive Suite #1 Peoria, AZ 85381 Phone: 800-752-5582 www.premierh2o.com Fax: 623-866-5666

P/N: 199214

Page 1

Manual Edition: 01/22/15

Page 2

Thank you for your purchase of a state of the art Premier Reverse Osmosis (RO) water treatment system. Water quality concerns are quickly becoming more of a focus for the public. Lately you may have heard about contaminants in the drinking water, such as arsenic, chromium, cryptosporidium or Giardia. There may also be some local water issues in your area such as high levels of lead and copper. This Premier water treatment system has been designed and tested to provide you with high quality water for years to come. The following is a brief overview of the system.

Your Reverse Osmosis System:

Osmosis is the process of water passing through a semi permeable membrane in order to balance the concentration of contaminants on each side of the membrane. A semi permeable membrane is a barrier that will pass some particles like clean water, but not other particles like arsenic and lead.

Reverse osmosis uses a semi permeable membrane; however, by applying pressure across the membrane, it concentrates contaminants (like a strainer) on one side of the membrane, producing crystal clear water on the other. This is why RO systems produce both clean drinking water and waste water that is ﬂ ushed from the system. This reverse osmosis system also utilizes carbon block ﬁ ltration technology, and can therefore provide a higher quality drinking water than carbon ﬁ ltration systems alone.

Y our system is a four stage RO which is based upon four separate treatment segments within the one complete water ﬁ ltration system. These stages are as follows:

Stage 1 – Sediment ﬁ lter, recommended change 6 months.*

The ﬁ rst stage of your RO system is a ﬁ ve micron sediment ﬁ lter that traps sediment and other particulate matter like dirt, silt and rust which affect the taste and appearance of your water.

Stage 2 – Carbon ﬁ lter, recommended change 6 months.*

The second stage contains a 5 micron carbon block ﬁ lter. This helps ensure that chlorine and other materials that cause bad taste and odor are greatly reduced.

Stage 3- Membrane, recommended change 2-5 years.

Stage three is the heart of the reverse osmosis system, the RO membrane. This semi permeable membrane will effectively take out TDS, Sodium and heavy metals such as arsenic, copper, and lead, as well as Cysts, such as Giardia and cryptosporidium. Because the process of making this high quality drinking water takes time, your RO water treatment system is equipped with a storage tank.

Stage 4- Carbon Block, recommend change 6 months.*

The ﬁ nal stage is a carbon block ﬁ lter. Some RO units are equipped with a standard ﬁ lter which is used as a ﬁ nal polishing ﬁ lter. Some units are equipped with a specialty volatile organic chemical (VOC) reducing block. This specialty ﬁ lter will reduce other organic chemicals such as herbicides and pesticides that may be in your water.

System Maintenance

Just because you can not taste it, does not mean that it is not there. Contaminants such as lead, chromium and arsenic (to name a few) are undetectable to the taste. Additionally, over time if you do not replace the ﬁ lter element, other bad tastes and odors will be apparent in your drinking water.

This is why it is important to change out your ﬁ lter at the recommended intervals as indicated in this system manual. When replacing the ﬁ lter elements, pay special attention to any cleaning instructions. Should you have any further questions please refer to our website at www.premierh2o.com or call our customer service dept. at 1-800-752-5582.

*KP-4 R.O. unit is equipped with annual ﬁ lters, therefore require only one annual ﬁ lter change.

Page 2

Page 3

With proper installation and maintenance, this system will provide you with high quality water for years to come. All of Premier’s water enhancement products are rigorously tested by independent laboratories for safety and reliability. If you have any questions or concerns, please contact our customer service department at 1-800-752-5582 (outside USA 480-675-7995) or refer to our on-line trouble shooting at www.premierh2o.com.

Table of Contents

Operational Parameters ........................................................................................................................ 4

Contents of Reverse Osmosis System .................................................................................................. 4

Tools Recommended For Installation .................................................................................................... 4

Drill a Hole for the Faucet in a Porcelain Sink ....................................................................................... 5

Punch a Hole for the Faucet in a Stainless Steel Sink ..........................................................................5

Faucet Installation ................................................................................................................................. 6

Adapt-a-Valve Installation ..................................................................................................................... 7

Drain Saddle Installation........................................................................................................................ 7

Drill hole and Connect 3/8” Black Tube from Faucet to the Drain Saddle ............................................. 8

Green Tube Connection ......................................................................................................... ............... 8

Reverse Osmosis Module Mounting...................................................................................................... 8

Tank Elbow Installation .......................................................................................................................... 8

Connect Blue Tube from “TANK” Port on RO Module to the Tank ......................................................... 9

How to use Quick Connect Fittings............................................................................................. .......... 9

Connect the Red Tube from Faucet to RO Module ............................................................................. 10

Connect the Blue Tube from the Faucet to RO Module....................................................................... 10

Start up Instructions..............................................................................................................................11

6 Month Maintenance .......................................................................................................................... 12

Annual Maintenance ............................................................................................................................ 13

Membrane Replacement .................................................................................................................... 14

Checking Air Pressure in the Tank ...................................................................................................... 15

Procedure for extended Non-Use ....................................................................................................... 15

Trouble Shooting ................................................................................................................................. 16

Arsenic Fact Sheet. ............................................................................................................................. 17

Performance Data Sheet ..................................................................................................................... 18

One Piece Manifold Drawing / Parts List ............................................................................................. 19

Other Products ............................................................................................................................. 20-22

Warranty Registration .....................................................................................................................23-24

Service Record ................................................................................................................................... 25

Limited Warranty ................................................................................................................................ 26

Page 3

Page 4

Operational Parameters

Installation must comply with state and local plumbing regulations. This system is intended to be installed on the cold water line only.

Operating Temperatures: Maximum 100°F (37.8°C) Minimum 40°F (4.4°C)

Operating Pressure: Maximum 85 psi (6.0 kg/cm pH Parameters: Maximum 11 Minimum 2 Iron: Maximum 0.2 ppm

) Minimum 40 psi (2.80 kg/cm

TDS (Total Dissolved Solids) < 1800 ppm Turbidity < 5 NTU

Hardness: Recommended hardness not to exceed 10 grains per gallon, or 170ppm. System will operate with hardness over 10 grains but the membrane life may be shortened. Addition of a water softener may lengthen the membrane life.

Water Pressure: The operating water pressure in your home should be tested over a 24 hour period to attain the maximum pressure. If the incoming water pressure is above 85 psi a pressure regulator is recommended and if over 100 psi then a pressure regulator is required. Should you need a gauge to check your water pressure, see page 23 (item no. 261003).

Copper Tubing: Reverse Osmosis water should not be run through copper tubing as the purity of the water will leach copper causing an objectional taste in water and pin holes may form in the tubing. Premier supplies speciality ﬁ lters (part number 107008) that can be used if copper tubing follows the Reverse Osmosis unit. Be sure to follow any state or local regulations during installation.

)

Contents of Reverse Osmosis (RO) System

1 Tank – White 1 Module – White 1 Parts Bag 1 Faucet Bag

1 Manual and Warranty Card

If any of the items are missing please contact Premier prior to installing.

Tools Recommended For Installation

1 1/4" Hole Saw Bit for Faucet opening Round Knock out Punch for Stainless Sinks 1 ¼” Adjustable Wrench Sharp Knife 1 / 2" - 13/16” Open End Wrenches Phillips Screw Driver Needle Nose Pliers – Adjustable Pliers Electric Drill 1/8", 1/4" & 3/8" Drill Bits

Page 4

Page 5

Drill a Hole for the Faucet in a Porcelain Sink

Note:

Most sinks are pre drilled with 1 ½” or 1 ¼” diameter hole that you can use for your RO faucet. (If you are already using it for a sprayer or soap dispenser, see step 1)

Porcelain sinks are extremely hard and can crack or chip easily. Use extreme caution when drilling. Premier accepts no responsibility for damage resulting from the installation of faucet.

Step 1

Determine desired location for the RO faucet on your sink and place a piece of masking tape on over where the hole is to be drilled. Mark the center of the hole on the tape.

Step 2

Using a variable speed drill set on the slowest speed, drill a

/8“ pilot hole through both porcelain and metal casing of sink at the marked center of the desired location. Use lubricating oil or liquid soap to keep the drill bit cool (If drill bit gets hot it may cause the porcelain to crack or chip).

Step 3

Using a 1 ¼” hole saw, proceed to drill the large hole. Keep drill speed on the slowest speed and use lubricating oil or liquid soap to keep the hole saw cool during cutting.

Step 4

Make sure the surroundings of the sink are cooled before mounting the faucet to the sink after drilling and remove all sharp edges.

Punch a Hole for the Faucet in a Stainless Steel Sink

Note:

Step 5

If mounting faucet to a Stainless Steel Sink you will need a 1 ¼” Hole Punch. The faucet opening should be centered between the back splash and the edge of the sink, ideally on the same side as the vertical drain pipe.

Drill a ¼” pilot hole. Use a 1/2” Hole Punch and an adjustable wrench to punch the hole in the sink. Change to the 1 ¼” Hole Punch to enlarge the hole.

The faucet can now be installed.

Page 5

Page 6

Standard Faucet Installation

Step 6

Remove nut (item 11) and blue tubing (item 12) from faucet (Leave the nut and plastic delrin sleeve (item 10) on the blue tube).

Step 7

Feed both the red and black tubing through the pre drilled hole in the sink/counter until faucet is seated.

Step 8

Under the sink - on to the threaded faucet stem in order ﬁ rst slide on the rubber gasket (item

6), the slotted washer (item 7), the white spacer with the open end UP (item 8), the hex nut washer (item 9), and lastly secure with nut (item 11).

Step 9

Make sure the plastic delrin sleeve (item 10) is on the end of the blue tube, push the white plastic insert (item 13) into the end of blue tubing with the delrin sleeve, insert the blue tube (item 12) into the faucet stem and secure with nut (item 11).

Note:

DO NOT overtighten nut.

Page 6

Page 7

Adapt-a-Valve Installation

Caution:

Water supply line to the system must be from the cold water supply line only. Hot water will severely damage your system.

* Washer

Conﬁ guration for 3/8”

(With Brass Fittings)

* Insert White Washer

Hot

Supply

Cold

Supply

Conﬁ guration for 1/2”

(Without Brass Fittings)

Do not use Teﬂ on tape with the Adapt-a-Valve.WARNING:

Step 10 Step 11

Turn off the cold water supply to the faucet by turning the angle stop valve completely off. Attach the adapt-a-valve as illustrated in the three photos above, choosing the conﬁ guration

that ﬁ ts your plumbing.

Drain Saddle Installation - Part# 164016

Drain Saddle ﬁ ts standard 1 ¼” – 1 ½” drain pipes Caution:

Step 12

If you have a garbage disposal, do not install the drain saddle near it. Installation of the drain saddle must be either above the garbage disposal, or if a second sink drain is available, install it above the cross bar on the second drain. Installation of the drain saddle near a garbage disposal may cause the drain line to plug. If no other installation of drain line is available, Premier offers drain line installation kit (part number 164020) that can be used with garbage disposals.

Gather the pieces of the drain saddle: 1 Black compression nut 1 Semicircle bracket with opening

2 Screws 1 Foam gasket 2 Nuts for screws 1 Semicircle bracket

Step 13

The small square black foam gasket with a circle cut out of the middle must be applied to the inside of the drain saddle. Remove sticky tape backing and stick to the drain saddle as shown.

Step 14

The drain saddle must be mounted at least 1 ½” above the nut of the P-trap or cross bar from the garbage disposal to insure proper drainage. Assemble the drain saddle around the drain pipe at the best available location. Using Phillips screw driver tighten screws evenly and securely on both sides of the drain saddle. Keep the plastic compression nut off at this time.

Caution:

Do not over tighten the screws. It may crack the drain saddle.

Page 7

Page 8

Drill hole and Connect 3/8” Black Tube from Faucet to the Drain Saddle

IMPORTANT:

The black 3/8” drain tube must be as SHORT and STRAIGHT as possible to the drain saddle, making a downward slope from faucet to drain saddle to allow for proper drainage. This is a gravity fed line and if there is any bend or dip in the tube, the rinse water will not ﬂ ow into the drain properly. Water may back up and come out the air gap hole in the back of the faucet.

Step 15

Caution:

With the drain saddle secured onto the drain pipe, using a 1/4” drill bit installed in your electric drill, insert the drill bit through the opening in the drain saddle and drill through the drain pipe.

It is very important to keep the drill centered to prevent damage of the drain saddle while drilling.

Step 16

Measure the 3/8” black tube from faucet to the drain saddle on the drain pipe and make a straight cut to the correct length.

Step 17

Slip black tube through black compression nut. Insert black tube into the opening in the drain saddle and hand tighten the black nut, and add 1/4 turn with a wrench.

Green Tube Connection

Step 18

Locate green tube attached to the RO Module. Insert the open end of the green 1/4” tube into the open 1/4” quick connect ﬁ tting on the plastic water feed valve making sure the tube is pushed in all the way to the tube stop.

Reverse Osmosis Module Mounting

Step 19 Determine best location for the RO module to be mounted to allow

for future system maintenance. The parts bag has 2 self tapping screws. Using an electric drill with a Phillips bit, screw them into the cabinet wall 6” apart and 16” from the bottom of the cabinet.

Do not cut any RO system tubes at this timeNote:

Tank Elbow Installation

Step 20

Note:

Step 21

Wrap (7 to 12 turns) of Teﬂ on tape clockwise around the male pipe threads (MPT) on the Stainless Steel ﬁ tting on top of the tank.

Do not let the tape cover the opening.

Thread the plastic elbow (supplied in the parts bag) onto the stainless steel connection on the top of tank. Tighten using an adjustable wrench. Do not over tighten as plastic could crack.

Page 8

Page 9

Connect Blue Tube from “TANK” Port on RO Module to the Tank

Step 22

Position tank in desired location. Stand it upright or lay it on its side (using the black plastic stand). Measure the blue tube from the RO module port marked “TANK” over to the tank

Step 23

and cut it to desired length. Insert the blue 3/8” tube into the compression side of the elbow previously installed on top of

the storage tank and push in as far as it will go. Tighten the compression nut securely with a wrench.

How To Use the Quick Connect Fittings on the RO Module

To make a connection, the tube is simply pushed into the ﬁ tting. The unique patented John Guest® locking system holds the tube ﬁ rmly in place without deforming it or restricting ﬂ ow .

It is essential that the outside diameter be free of score marks and that burrs and sharp edges be removed before inserting into ﬁ tting.

Push the tube into the ﬁ tting, to the tube stop. The collet (gripper) has stainless steel teeth which hold the tube ﬁ rmly in position while the O-ring provides a permanent leak proof seal.

Fitting grips before it seals. Ensure tube is pushed into the tube stop.

Pull on the tube to check that it is secure. It is a good practice to test the system prior to leaving site and /or before use.

T o disconnect, ensure the system is depressurized before removing the tube. Push in collect squarely against face of ﬁ tting. With the collet held in this position, the tube can be removed. The ﬁ tting can then be reused.

Page 9

Page 10

Connect the Red Tube from Faucet to RO Module

Step 24

Insert the open end of the red 1/4” tube attached to the RO faucet into the 1/4” X 1/4” quick connect ﬁ tting on the RO Manifold. Make

Connect the Blue Tube from the Faucet to RO Module

sure the tube is pushed in all the way to the tube stop. (See Picture)

Connect red faucet tube.

Step 25

Insert the blue 3/8” tube from the faucet into the port on the module marked “FAUCET”. Make sure the tube is pushed in all the way to the tube stop.

Note:

A connection to a refrigerator / ice maker may be tee’d into this blue tube. Premier offers an ice maker install kit part # 500102 (See Page 22).

Page 10

Page 11

Congratulations!

You have completed the installation of your new Reverse Osmosis system.

Start up Instructions

Step 1

Turn on the incoming cold water at the angle stop valve. Open the needle valve on the brass Adapt-a-V alve by turning counter clockwise. Check the system for leaks and tighten any ﬁ tting as necessary. (Check frequently over the next 24 hours to ensure no leaks are present).

Step 2

If you have connected your RO system to a refrigerator / ice maker, make sure the ice maker is off (do not allow water to ﬂ ow to the ice maker) until ﬂ ushing (Step 5) is complete and the tank has been allowed to completely ﬁ ll. Connection from the RO to the ice maker system should have an in-line valve installed before the ice maker so it can easily be closed to prevent water ﬂ owing to the ice maker during start up and periodic maintenance. Your RO tank must be allowed to ﬁ ll up fully in order for the ice maker system to work properly.

Please Follow the Startup Instructions.

Step 3

Step 4

Open the RO faucet and leave it open until water begins to trickle out (it will come out slowly).

Close the RO faucet allowing the storage tank to ﬁ ll with water. It may take 4 to 6 hours to ﬁ ll the tank completely depending on the production capability of the membrane, local water temperature and water pressure.

Note:

Step 5

During the ﬁ ll period you may hear water trickling due to the Reverse Osmosis Process.

After the Tank has ﬁ lled, open the RO Faucet to ﬂ ush the tank completely. You will know that the tank is empty when the ﬂ ow rate from the RO faucet is down to a trickle. Repeat this step two more times. The fourth tank can be used for drinking.

The ﬂ ushing process should take about 24 hours to complete.

Note:

Flushing of the tank 3 times is only necessary during the initial startup and after replacing the membrane.

Don’t Forget To Register!

Register by mail, phone, fax or internet. Premier uses this information only to provide a ﬁ lter change reminder notice. Pre-ﬁ lters should be changed every 6 months and Final Polishing ﬁ lter annually. You may register your system via our website at www.premierh2o.com or call 1-800-752-5582 (within USA only) / FAX#: 623-866-5666.

Page 11

Page 12

6 Month System Maintenance

*Order ﬁ lters by calling 1-800-752-5582 or buy online at www.premierh2o.com.

Note: The KP-4 R.O. unit is equipped with annual ﬁ lters, therefore require only one annual change.

Stage 1 - Sediment Filter (part #: 104017) Stage 2 - Carbon Filter Stage 4 - Carbon Filter

Part#:101009 • Part#:100037: KP-4

• Part#:101009: WP-4, WP4-50

Step 1

Step 2

Turn off the incoming water supply to the RO at the adapt-a-valve. (Follow the green tube away from the RO system to ﬁ nd the adapt-a- valve.)

Open the RO Faucet and allow water to drain from the tank until it is completely empty.

Note:

Water Can be saved in a container for drinking or to rinse system parts.

Step 3

Let system sit for a few minutes after tank is empty to depressurize before attempting to remove ﬁ lter housings.

Step 4

For more leverage you may leave the RO module attached to wall of cabinet. If you are unable to access the module while it hangs, remove it prior to changing ﬁ lters. Starting with the closest housing (Stage 1), remove it by turning it clockwise, empty water, then discard ﬁ lter. Continue on to the 2

Step 5

Clean ﬁ lter housings (bowls) with a mild soap solution and rinse with water. Check O-rings and lubricate with water soluble lubricant. KY

Jelly® or other water based lubricants may be used. Petroleum based lubricants (such as Vaseline®) must not be used.

Caution:

Before re-installing the ﬁ lter bowls back on to the system , check O-rings to make sure they are still in place.

& 3

housing (Stage 2 & 4).

Step 6

Insert the new sediment ﬁ lter (cloth like appearance) into the 1st ﬁ lter housing which is the one closest to the side with tubing connections and re-install housing.

Step 7

Insert the new Carbon Block ﬁ lter (White End Caps) into the 2nd and 4th stage housing and re-install housing.

Step 8 Step 9

Turn water on to the unit at the adapt-a-valve. Open the RO faucet and leave it open until water begins to trickle out

(it will come out slowly).

Step 10

Page 12

Page 13

Annual Maintenance

*Order ﬁ lters by calling 1-800-752-5582 or buy online at www.premierh2o.com.

Stage 1 - Sediment Filter (part #: 104017) Stage 2 & 4 - Carbon Block Filter (part #: 101009-White end caps) 1/2 Cup of hydrogen peroxide or common household bleach.

Note:

Step 1

Note:

Step 2

Sanitizing of unit is recommended.

Perform steps 1 through 5 in the Six Month System Maintenance (Page 12).

If not sanitizing the system skip to step 8.

Remove the RO membrane from its housing and rest in a clean sanitary place. (Refer to “Membrane Replacement” section on page 14 for directions on removing the membrane). Replace cap onto empty membrane housing and re-connect green tubing.

Step 3

Step 4

Leaving the ﬁ lters out, replace stage 2 and 4 empty ﬁ lter housings (hand tight) onto unit. Measure & pour either 1/2 cup of hydrogen peroxide or common household bleach into the 1st ﬁ lter housing (Stage 1) and hand tighten onto unit.

With the RO faucet in the closed position turn on the incoming water supply to the system by turning the adapt-a-valve counter clockwise. Wait 1 minute for the unit to pressurize. Turn on the RO faucet and let the water run for 30 seconds. Turn off the RO faucet and let the unit rest for 2 minutes. Finally, open the RO faucet and let the water run for 5 more minutes.

Step 5

Turn off the incoming water supply to the system by turning the adapt-a-valve clockwise until it stops. Keep the RO faucet open until the storage tank is completely drained.

Step 6

Open the membrane housing and re-install the RO membrane while making sure not to kink the O-rings. (Refer to “Membrane Replacement” section on page 14 for directions on installing the membrane). Tighten the cap back on the housing and reconnect green tubing.

Step 7

Caution:

Step 8

Step 9

Tip:

Step 11

Remove ﬁ lter housings Stage 1, 2 and 4 and empty of water.

Before re-installing the ﬁ lter bowls back on to the system , check O-rings to make sure they are still in place and lubricate with water soluble lubricant.

Insert the new sediment ﬁ lter (cloth like appearance) into the 1

ﬁ lter housing which is the one

on the water inlet side (green tubing from the adapt-a-valve) of the RO system and re-install housing.

Insert the new Carbon Block ﬁ lter (White End Caps) into the 2nd and 4th stage housing and re-install housing.

This is a good time to check the air pressure in your storage tank. For instructions please see page 16.

Follow Steps 8 through 10 in the Six Month System Maintenance (Page 12) for startup directions.

Page 13

Page 14

This reverse osmosis system contains a replaceable component (the RO membrane) which is critical to the efﬁ ciency of the system. Replacement of this reverse osmosis membrane should be with one of identical speciﬁ cations as deﬁ ned by Premier to assure the same efﬁ ciency and contaminant reduction performance.

Membrane Replacement

Membranes have a life expectancy between 2 and 5 years, depending on the incoming water conditions and the amount the RO system is used. This reverse osmosis membrane is critical for effective reduction of total dissolved solids (TDS). The product water should be tested periodically to verify that the system is performing satisfactorily . Normally, a membrane would be replaced during a semiannual or annual ﬁ lter change. However, if at any time you notice a reduction in water production or an unpleasant taste in the reverse osmosis water, it could be time to replace the membrane. Premier recommends replacing the membrane when TDS reduction falls below 75%.

Note:

A water sample may be sent to Premier for a free diagnosis of your membranes performace. To send a water sample, use two (2) clean containers and ﬁ ll ½ cup of tap water in one container and ½ cup of reverse osmosis water in 2nd container. Clearly label each sample. Send the samples to the address listed on the cover of this manual attention “Water Samples”. Premier will test the water and mail or call you with the results.

Step 1

Turn off the incoming water supply to the RO at the adapt-a-valve. (Follow the green tube away from the RO system to ﬁ nd the adapt- a-valve.)

Step 2

Open the RO Faucet and allow water to drain from the tank until it is completely empty.

Step 3

Remove the horizontal membrane housing on top of the unit by turning it counter clockwise to loosen.

Step 4

Pull ﬁ rmly on the yellow RO membrane to remove it from the housing and discard.

Step 5

Lubricate the O-rings on the new membrane with a water soluble lubricant such as KY Jelly ®. Insert the end with the two black O-rings into the cap. Twist the membrane as you push it ﬁ rmly into the manifold.

Caution:

Before re-installing the membrane housing back on to the system, check O-ring on the housing to make it is still in place and lubricate with water soluble lubricant.

Step 6 Replace the membrane housing onto the cap by turning clockwise.

Tighten securely.

Step 7 Follow Start up instructions on page 11.

Page 14

Page 15

Check Air Pressure in the Tank

Important:

Check air pressure only when tank is empty of water!

Check air pressure in the storage tank when you notice a decrease in available water from

Step 1

the RO system. Air can be added with a bicycle pump using the schrader valve that is located on the lower side of the tank behind a blue plastic cap.

Turn off the incoming water supply to the RO at the adapt-a-valve. (Follow the green tube away from the RO system to ﬁ nd the adapt- a-valve.)

Step 2

Tip:

Step 3

Open the RO Faucet and allow water to drain from the tank until it is completely empty.

When water from the RO faucet slows to a trickle, with the faucet still in the open position, you may add air to the tank to purge any left over water, this will ensure that the tank is completely empty.

Once all water in the tank is purged, check air pressure using an air pressure gauge, it should read between 5 - 7 PSI. (Digital air pressure gauge is recommended)

Procedure for Extended Non-Use (More than 2 months)

Turn off the water supply to the RO at the adapt-a-valve and open the RO faucet to empty the storage tank (Save a few ounces of RO water). Once the storage tank is empty, remove the membrane and place it in a sealed plastic bag with the RO water saved earlier and store in your refrigerator.

For restart, reinstall membrane and follow startup procedure on page 11.

Page 15

Page 16

TROUBLE SHOOTING

Problem Cause Solution

1. Low/Slow Production Low Water Pressure Assure a minimum of 40 psi incoming water pressure. Premier sells a booster pump if home water pressure is low. Maker sure water supply is turned on and Adapta Valve is all the way open Crimps in tubing Check tubing and straighten or replace as necessary. Clogged pre-ﬁ lters Replace pre-ﬁ lters. Fouled membrane Replace membrane and clean ﬂ ow restrictor.

2. Milky colored Water Air in system Air in the system is a normal occurrence with initial start up of the RO system. This milky look will disappear during normal use within 1-2 weeks. If condition reoccurs after ﬁ lter change, drain tank 1 to 2 times.

3. Water constantly Low water pressure See #1 Above running unit will not shut off Fouled membrane Replace membrane High water pressure Check incoming water pressure to make sure it does not exceed 100 psi. A presser relief valve may be necessary. High air pressure in tank Empty storage tank of water. Set tank air pressure to 5 psi. See previous page.

4. Noise from faucet or drain Air gap faucet Inherent sound with air-gap faucets. Location of drain saddle See diagram for proper location of drain saddle. Higher capacity membrane Normal with high capacity membrane High water pressure Check incoming water pressure to make sure it does not exceed 100 psi. A presser relief valve may be necessary.

5. Faucet leaks from Crimp or loop in drain line Straighten black 3/8 drain tube. Cut off any excess tubing the air gap feature Drain tube clogged/restricted Caused from dishwasher or garbage disposal. Disconnect the 3/8” black tube at the drain, clean the 3/8” black tube out with a wire, then reconnect.

6. Small amount of water in System just starting up Normally it takes 6-10 hours to ﬁ ll tank. Note: Low storage tank pressure and/or temperature can drastically reduce production rate. Low water pressure See #1 Above Too much air in tank Add air if below 5 psi and bleed if above 5 psi. Check only when tank is empty of water. See previous page.

7. Water leaks from the Not properly tightened. Tighten the bowl ﬁ lter housing Missing or kinked O-ring Turn off the water supply. Release the pressure, remove bowl and replace the O-ring. (p/n 113043). Make sure the O-ring is seated in the ﬁ lter bowl properly before reinstalling the ﬁ lter bowl.

Page 16

Page 17

Arsenic Fact Sheet

Arsenic (As) is a naturally occurring contaminant found in many ground waters. Arsenic in water has no color, taste or odor. It must be measured by an arsenic test kit or lab test. Public water utilities must have their water tested for arsenic. You can obtain the results from your water utility contained with in your consumer conﬁ dence report. If you have your own well, you will need to have the water evaluated. The local health department or the state environmental health agency can provide a list of test kits or certiﬁ ed labs.

There are two forms of arsenic: pentavalent arsenic (also called As (V), As (+5))and trivalent arsenic (also called As (III), As (+3)). In well water, arsenic may be pentavalent, trivalent, or a combination of both. Although both forms of aresenic are potentially hazardous to your health, trivalent arsenic is considered more harmful than pentavalent arsenic.

RO systems are very effective at removing pentavalent arsenic. A free chlorine residual will rapidly convert trivalent arsenic to pentavalent arsenic. Other water treatment chemicals such as ozone and potassium permanganate will also change trivalent arsenic to pentavalent arsenic. A combined chlorine residual (also called chloramine) may not convert all the trivalent arsenic. If you get your water from a public water utility, contact the utility to ﬁ nd out if free chlorine or combined chlorine is used in the water system.

This Premier reverse osmosis system is designed to remove up to 98% of pentavalent arsenic. It will not convert trivalent arsenic to pentavalent arsenic. Under laboratory standard testing conditions, this system reduced 0.30 mg/L (ppm) pentavalent arsenic to under 0.010 mg/L (ppm) (the USEPA standard for drinking water). Actual performance of the system may vary depending on speciﬁ c water quality conditions at the consumer’s installation.

The RO component of this Premier reverse osmosis system must be maintained according to its recommended maintenance cycle. Speciﬁ c component identiﬁ cation and ordering information can be found in the installation/operation manual maintenance section, by phone at 1-800-752-5582 or online www.premierh2o.com. California Proposition 65 Warning WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information: Watts.com/ prop65

Page 17

Page 18

Performance Data Sheet

WP-4, KP-4

Premier Inc.

8716 W. Ludlow Drive Suite #1

Peoria, AZ 85381

GENERAL USE CONDITIONS:

1. System to be used with municipal or well water sources treated and tested on regular basis to insure bacteriological safe quality. DO NOT use with water that is microbiologically unsafe or unknown quality without adequate disinfection before and after the system. Systems certiﬁ ed for cyst reduction may be used on disinfected water that may contain ﬁ lterable cysts.

2. Operating Temperature: Maximum: 100°F (40.5°C) Minimum: 40° (4.4°)

3. Operating Water Pressure: Maximum: 85 psi (6.0kg/cm2) Minimum: 40 psi (2.8kg/cm2)

4. pH 2 to 11

5. No iron present in incoming feed water supply.

6. Hardness of more than 10 grains per gallon (170 ppm) may reduce RO membrane life expectancy.

7. Recommend TDS (Total Dissolved Solids) not to exceed 1800 ppm.

This system has been tested according to NSF/ANSI 58 for reduction of the substances below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system as speciﬁ ed in NSF/ANSI 58. This system has been tested for the treatment of water containing pentavalent arsenic (also known as As (V), As (+5), or arsenate) at concentrations of 0.30 mg/L or less. This system reduces pentavalent arsenic, but may not remove other forms of arsenic. This system is to be used on water supplies containing a detectable free chlorine residual at the system inlet or on water supplies that have been demonstrated to contain only pentavalent arsenic. Treatment with chloramine (combined chlorine) is not sufﬁ cient to ensure complete conversion of trivalent arsenic to pentavalent arsenic, Please see the Arsenic Facts section of the Performance Data Sheet for further information. Avg. In. Avg. Eff. % Reduction pH Pressure Max Eff. Inf. challenge Max Allowable

(mg/L) (mg/L) mg/L concentration concentration mg/L mg/L

Arsenic (Pentavalent) 334.62 ug/L 5.039 ug/L 98.4% 50psi 19 ug/L 0.30±10% 0.010 mg/L Barium Reduction 10.2 0.13 98.7% 7.24 50psi 0.27 10.0±10% 2.0 Cadmium Reduction 0.031 0.0001 99.7% 7.49 50psi 0.0009 0.03±10% 0005 Chromium (Hexavalent) 0.30 0.006 98.0% 7.24 50psi 0.013 0.03±10% 0.1 Chromium (Trivalent) 0.30 0.003 99.0% 7.24 50psi 0.008 0.03±10% 0.1 Copper Reduction 3.0 0.04 98.7% 7.64 50psi 0.06 3.0±10% 1.3 Cysts 222,077#/ml 10 #/ml 99.99% 50psi 58 minimum 50,000/mL N/A Fluoride Reduction 8.0 0.33 95.9% 7.49 50psi 0.47 8.0±10% 1.5 Lead Reduction 0.15 0.004 97.3% 7.49 50psi 0.008 0.15±10% 0.0107 Radium 226/228 25pCi/L 5pCi/L 80.0% 7.24 50psi 5pCi/L 25pCiL±10% 5pCiL Selenium 0.10 <0.001 99.0% 50psi <0.001 0.10±10% 0.05 TDS 765 24 96.8% 7.84 50psi 39.0 750±40mg/L 187 Turbidity 81 NTU 0.15 NTU 99.8% 50psi 0.28 NTU 11±1 NTU 0.5 NTU

Description Replace

Sediment Filter  Part# 104017 6 Months Carbon Filter

 Part# 101009 (WP-4) 6 Months  Part# 100037 (KP-4) 12 Months

Depending upon incoming feed water conditions replacement time frame may vary.

Description Replace

Stage 4 - Carbon Filter

 Part# 101009 6 Months

RO Membrane

 25 GPD Part# 110009 2 to 5 Years

Recovery - 16.23% Daily Production Rate - 9.56 GPD Efﬁ ciency - 9.58%

Depending on water chemistry, water temperature, and water pressure Premier’s R.O. Systems production and performance will vary. Efﬁ ciency rating means the percentage of the inﬂ uent water to the system that is available to the user as reverse osmosis treated water under operating conditions that approximate typical daily usage. Recovery rating means the percentage of the inﬂ uent water to the membrane portion of the system that is available to the user as reverse osmosis treated water when the system is operated without a storage tank or when the storage tank is bypassed. There is an average of 4 gallons of reject water for every 1 gallon of product water produced. REFER TO OWNER’S INSTALLATION/SERVICE MANUAL FOR FURTHER MAINTENANCE REQUIREMENTS AND WARRANTY INFORMATION.

Phone: (480) 675-7995 Fax: (623) 866-5666 Email: [email protected]

Page 18

Page 19

Item Qty Part # Description 1 1 101009 Carbon Block-10 Inch-5M 2 1 104017 Sediment Filter-10 Inch-5M 3 1 110016 RO Membrane 35GPD 4 1 110019 RO Membrane 50GPD 5 3 113018 Filter Bowl 6 1 113035 Membrane V essel 7 3 113041 O-Ring Filter Bowl 8 1 113045 O-Ring Membrane Vessel 9 1 116001 Faucet-AG-Chrome 10 1 119007 Tank-Pressure 3GAL White 11 1 125032 Elbow Fitting 3/8” Tank 12 1 560080 Adapt-a-Valve 13 1 164016 Drain Saddle 3/8” 14 1 610003 Prepared Lid, Manifold

Page 19

Page 20

Other Products from Premier

Premier has other ﬁ ne water ﬁ ltration products and accessories to enhance your water and to compliment your existing RO System. Listed on the next several pages are only a few of the items we offer. Visit our web site at www.premierh2o.com or call our Customer Service Representatives at 1-800-752-5582 (inside USA) 1-480-675-7995 (outside USA) for more products.

Premier offers a ﬁ lter change kit which includes all replacement ﬁ lters needed. Call 1-800-752-5582 or buy on-line at www.premierh2o.com.

Top Mount Faucets by Premier

These attractively designed faucets feature a long reach spout to compliment all styles of kitchen decor. The unique top mount design allows for easy above counter installation. The Monitored version of this faucet has an LED light that turns red to notify you for ﬁ lter replacement.

Part No. 116091 - Chrome (Non-Monitored) *$47.95 each

116095 - Brushed Nickel (Non-Monitored) *$52.95 each 116094 - Chrome (Monitored) *$57.95 each 116093 - Brushed Nickel (Monitored) *$62.95 each

3/8” Ice Maker Kit for RO and Filtration

3/8 inch connection includes 30 feet tubing, ball valve, and ﬁ ttings.

Part No. 500102 *$ 21.95/ea

Premier Hot Water Recirculation System

Bring convenience and saving to your home, giving you hot water instantly at every faucet, when you need it. This unique product is easy to install and not only provides you with the convenience of hot water when you need it, but saves an average of over 15,000 gallons per year.

Part No. 500800 *$229.99 each

50 GPD Membrane

Compatible with Premier Reverse Osmosis systems, this 50 GPD membrane generates a greater amount of water per day f or your RO system. Good application for households with higher levels of Nitrites & Nitrates. Contact Premier if you are in need of a Nitrite/Nitrate test kit.

Part No. 560018 (Membrane) *$ 80.95/ea

*All prices subject to change without notice.

Page 20

Page 21

PERMEATE PUMP KIT

Using only the available energy from the brine water (otherwise lost to the drain), the pump forces product water into the storage tank. This process effectively reduces membrane back pressure to less than 5 psi and allows the membrane to maximize its use of the available feed pressure.

· Fills product tank up to 4 times more rapidly · Reduces waste water by as much as 80%

· Lowers “TDS creep” · NSF approved (Standard 58)

Part No. 560041 *$65.95/ea

Pocket Total Dissolved Solids (TDS) Monitor

Test water electronically to verify reverse osmosis membrane effectiveness. Carrying case included.

Part No. 273001 *$39.95/ea

Water Pressure Gauge

This gauge mounts onto your outside hose connection to accurately show your home’s water pressure up to 300 psi. A red needle shows peak overnight pressure, which may exceed readings during the day . High pressure readings may indicate the need for pressure regulator to prevent damage to appliances.

Part No. 261003 *$14.95 each

Whole House Filter

Great for sediment problems such as in well water supply or areas where dirt and rust particles are a problem. Includes three 50 micron sediment ﬁ lters and wrench (3/4” ports)

Part No. 500223 *$42.95/ea Replacement ﬁ lter

Part No. 304007 *$ 4.50/ea

Whole House High Performance Water Pressure Regulator

Provides water pressure control solutions for residential, commercial, and industrial applications. Offers durability and years of continuous trouble free operation.

Part No. 107001 *$69.95/ea

*All prices subject to change without notice.

Premier Ice Maker Filter Kit - High efﬁ ciency replaceable ﬁ lter that can last up

to 5 years or 20,000 gallons. Perfect for residential and commercial ice makers as well as refrigerators, drinking fountains, coffee & tea brewers, motor homes and campers. Reduces chlorine taste and odor.

Part No. 500318 *$32.95/ea

Page 21

Page 22

Removing chlorine from your shower

Special Chlorgon & KDF media – More effective then carbon medias with

hot water applications in the removal of the following.

 Free Chlorine (CL-)  Combined Chlorine (Sodium Hypochlorite)  Hydrogen Sulﬁ de (Rotten egg smell)  Plus, its pH balanced.

 Iron oxide (rust water)  Dirt, sediment  Odors

Deluxe Shower Handle with Built in Filter Replacement ﬁ lters 2PK 5-Way Massaging Spray 72” Reinforced Hose High Strength Bracket Triple Plated Finish Reversible Filter Cartridge (Model HHC) Cartridge Life Rating: 3 months

Part No. 107070 WHITE *$38.95 Part No. 107091 CHROME *$44.95 Part No. 107092 GOLD *$44.95

Part No. 107075 *$15.95/pk

Shower Falls Deluxe Shower Handle with Built in Filter

Curved Ergonomic Shower Handle Replacement ﬁ lters 2PK Filter Handle Extension Dual Swivel Adjustment Ultra Deluxe 5 Way Massaging Spray 72” Reinforced Hose Chrome Plated Brass Bracket & Swivel Ball Extension Triple Plated Finish Reversible Filter Cartridge (Model HHC) Cartridge Life Rating: 3 months

Part No. 107095 CHROME *$55.95

Part No. 107075 *$15.95/pk

All-In-One reversible High-Flow Filter Replacement ﬁ lter Deluxe 5-Way Massaging Spray

Soft-Touch Adjustment Pads

Anti-Scaling Spray Nozzle High Strength Housing Triple Plated Finish Cartridge Life Rating: 6 months

Part No. 107098 White/Chrome *$39.95 Part No. 107099 White/Gold *$39.95 Part No. 107080 *$13.95/ea

*All prices subject to change without notice.

Page 22

Page 23

WARRANTY REGISTRATION

Thank you for selecting Premier for your water ﬁ ltration needs.

4 Ways to Register

Premier Inc. is concerned for the safety of your personal information. Premier collects personal information when you register with Premier. This information is stored in our data base and we do not rent, sell, or share personal information with other people or nonafﬁ liated companies. We reserve the right to send you certain types of communications such as direct mail, email, or by telephone relating to our products or products that you have purchased. We limit access to your personal information to those employees who will directly provide you with services or products in order to do their jobs. We want to offer you four ways to communicate with us. 1.Online, 2.Fax, 3.Telephone, and 4. Mail the form below. By registering your product you will receive the full beneﬁ t of our warranty. Premier will also send you a semiannual ﬁ lter change reminder beginning six months from date of installation. To insure the highest quality of your water, ﬁ lters should be replaced every 6 months. If you have any ques- tions or comments please give us a call at 1-800-752-5582 M-F 8:00am -5:00pm MST.

1. Online at www.premierh2o.com

2. Call in your information 1-800-752-5582

Call and we will enter your information.

3. Fax in your information 623-866-5666

Fax this form directly to us.

Registering will

insure you re-

ceive Watts

FREE

4. Mail in the information.

Please complete the form below. Mail to: Premier

8716 W Ludlow Drive Suite #1 Peoria, AZ 85381

Filter

Reminder

Service

First Name:_________________________ Last Name:____________________________ Address: ________________________________________ City: ____________________ State: _______________________________________ Zip Code: ___________________ Country: USA CANADA MEXICO OTHER ____________ Phone # ______-__________ -__________ Email Address: ______________________ Date of Purchase: ___________________ Date of Install: _______________________ Installed By: SELF Plumbing Professional Where Purchased: ____________ Model Number: _______________________ Serial Number: ____ - __________

XXXXXX

XXXXX

Premier, Inc. 8716 W Ludlow Drive Suite #1 Peoria, AZ 85381 Phone: 800-752-5582 www.premierh2o.com Fax: 623-866-5666

Page 23

Page 24

WARRANTY REGISTRATION

Please Fill out and keep for your Records

XXXXXX

XXXXX

Iowa Department of Public Health - Sales in Iowa require this to be completed, signed and returned. These signatures will be retained on ﬁ le for two years.

Insert into envelope and return to Premier

Premier 8716 W Ludlow Drive Suite #1 Peoria, AZ 85381

Page 24

Page 25

Service Record

Serial No. _____________________

Date of Purchase:__________ Date of Install:___________ Installed by:__________________

Date

1st Stage Sediment (6 months)

2nd Stage Carbon (6 months)

4th Stage Carbon (1 year)

TFM Membrane (2-5 years)

NOTES:

Page 25

Page 26

Limited Warranty

What your Warranty Covers:

If any part of your Premier Reverse Osmosis System is defective in workmanship (excluding replaceable  lters and membranes), return unit a er obtaining a return authorization (see below), less tank, within 3 years of original retail purchase, Premier will repair or, at Premier’S option, replace the system at no charge.

How to obtain Warranty Service:

For warranty service, call 1-800-752-5582 for a return authorization number.  en, ship your Reverse Osmosis unit (less tank) to our factory, freight and insurance prepaid, with proof of date of original purchase. Please include a note stating the problem. Premier will repair it, or replace it, and ship it back to you prepaid.

What this warranty does not cover:

 is warranty does not cover defects resulting from improper installation, (contrary to Premier’s printed instructions), from abuse, misuse, misapplication, improper maintenance, neglect, alteration, accidents, casualties,  re,  ood, freezing, environmental factors, water pressure spikes or other such acts of God.

 is warranty will be void if defects occur due to failure to observe the following conditions:

1.  e Reverse Osmosis System must be hooked up to a potable municipal or well cold water supply.

2.  e hardness of the water should not exceed 10 grains per gallon, or 170 ppm.

3. Maximum incoming iron must be less than 0.2 ppm.

4.  e pH of the water must not be lower than 2 or higher than 11.

5.  e incoming water pressure must be between 40 and 100 pounds per square inch.

6. Incoming water to the RO cannot exceed 105 degrees F (40 degrees C.)

7. Incoming TDS/Total Dissolved Solids not to exceed 1800 ppm.

8. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or a er the system.

 is warranty does not cover any equipment that is relocated from the site of its original installation.

 is warranty does not cover any equipment that is installed or used outside the United States of America and Canada.

LIMITATIONS AND EXCLUSIONS:

Premier WILL NOT BE RESPONSIBLE FOR ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. PREMIER WILL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING TRAVEL EXPENSE, TELEPHONE CHARGES, LOSS OF REVENUE, LOSS OF TIME, INCONVENIENCE, LOSS OF USE OF THE EQUIPMENT, AND DAMAGE CAUSED BY THIS EQUIPMENT AND ITS FAILURE TO FUNCTION PROPERLY. THIS WARRANTY SETS FORTH ALL OF PREMIER’S RESPONSIBILITIES REGARDING THIS EQUIPMENT.

OTHER CONDITIONS:

If PREMIER chooses to replace the equipment, Premier may replace it with reconditioned equipment. Parts used in repairing or replacing the equipment will be warranted for 90 days from the date the equipment is returned to you or for the remainder of the original warranty period, whichever is longer.  is warranty is not assignable or transferable.

YOUR RIGHTS UNDER STATE LAW:

Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply.  is warranty gives you speci c legal rights, and you may have other legal rights which vary from state to state.

Page 26