X-SlotZ USB Module
User’s Guide
www.powerware.com
Powerware is a registered trademark and X-Slot is a trademark of Powerware Corporation.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
.
Copyright 2000 Powerware Corporation, Raleigh, NC, USA. All rights reserved. No part of this document may be
reproduced in any way without the express written approval of Powerware Corporation.
TABLE OF CONTENTS
Installation 3.....................................................
Inspecting the Equipment 3........................................................
Preparation 3.................................................................
Installing the USB Module 4.......................................................
Installing the Software 5.......................................................
Service and Support 6...........................................................
Two-Year Limited Warranty (US and Canada Only) 7......................................
International Limited Warranty 7....................................................
X-SlotZUSB Module User’s Guide : 05146515 A Uncontrolled Copy
3
Table of Contents
4
X-SlotZUSB Module User’s Guide : 05146515 A Uncontrolled Copy
INSTALLATION
The Universal Serial Bus Module (USB module) is an X-Slot
connectivity device that allows your UPS to communicate with a
USB-compliant computer using LanSafe III power management software.
The following requirements must be met to install the USB module:
A computer with a USB port
:
LanSafe III (v4.15 or higher) power management software
:
Microsoft Windows
:
A Powerware
:
Inspecting the Equipment
If any equipment has been damaged during shipment, keep the shipping
cartons and packing materials for the carrier or place of purchase and
file a claim for shipping damage. If you discover damage after
acceptance, file a claim for concealed damage.
To file a claim for shipping damage or concealed damage: 1) File with
the carrier within 15 days of receipt of the equipment; 2) Send a copy of
the damage claim within 15 days to your service representative.
Preparation
Before installing the USB module, complete the following list:
1. The UPS should be installed and operating in Normal mode
(see the UPS User’s Guide for installation instructions).
2. If LanSafe III/FailSafe III is installed on your PC, uninstall the
software.
9
98 or 2000
9
UPS with an X-Slot such as the 9125
Z
NOTE FailSafe III does not supportthe X-Slot USB module and must be uninstalled to
prevent installation and compatibility problems.
X-SlotZUSB Module User’s Guide : 05146515 A Uncontrolled Copy
5
Installing the USB Module
Installing the USB Module
To install the USB module, perform the following steps:
1. Remove the X-Slot cover (or existing X-Slot module) on the
UPS rear panel. Retain the screws (see Figure 1).
NOTE UPSs with a single X-Slot may have another X-Slot module already installed
(such as the Powerware 9125 UPS). If there is a communication cable attached to this
module, disconnect the cable and then remove the X-Slot module.
2. To prevent electrostatic discharge (ESD), place one hand on a
metal surface such as the UPS rear panel.
Align the USB module with the slot guides and slide the module
into the slot until it is firmly seated.
3. Secure the USB module with the screws removed in Step 1.
Figure 1. Removing the Single-Port Module
Figure 2. Installing the USB Module
4. Connect the USB module cable to the USB port on your
computer.
5. Continue to the following section, “Installing the Software.”
6
X-SlotZUSB Module User’s Guide : 05146515 A Uncontrolled Copy
Installing the USB Module
Installing the Software
After the USB module installation is complete, perform the following
steps to install the USB module drivers and software:
1. Insert the LanSafe III software CD into the CD-ROM drive.
2. Click
3. Select “Search for the best driver for your device” and click
4. Select “Specify at location” and click
5. Navigate to one of the following CD directories:
6. Click OK and Next.
7. When the “Windows driver file search for the device” prompt
8. Click
9. When the setup screen for the LanSafe III software opens,
Next when the “Add New Hardware Wizard” opens.
Next.
Browse.
CD Directory Operating System
\LanSafe\NTand95\ LanSafe III for Windows 95/98/NT 3.5x-4.0 (English)
\LanSafe\NTand95j\ LanSafe III for Windows 95/98/NT 3.5x-4.0 (Japanese)
NOTE
FailSafe III is not compatible with the X-Slot USB module.
appears, click
Finish.
Next.
install the software according to the onscreen instructions.
X-SlotZUSB Module User’s Guide : 05146515 A Uncontrolled Copy
7
Service and Support
Service and Support
If you have any questions or problems with the USB module, call your
Local Distributor or the Help Desk at one of the following telephone
numbers and ask for a USB module technical representative.
In the United States
In Canada
All other countries
1-800-365-4892
1-800-461-9166
1-919-870-3149
Please have the following information ready when you call the Help
Desk:
Model number
:
Date of failure or problem
:
Symptoms of failure or problem
:
Customer return address and contact information
:
If repair is required, you will be given a Returned Material Authorization
(RMA) Number. This number must appear on the outside of the
package and on the Bill Of Lading (if applicable). Use the original
packaging or request packaging from the Help Desk or distributor. Units
damaged in shipment as a result of improper packaging are not covered
under warranty. A replacement or repair unit will be shipped, freight
prepaid for all warrantied units.
NOTE For critical applications, immediate replacement may be available. Call the
Help Desk for the dealer or distributor nearest you.
8
X-SlotZUSB Module User’s Guide : 05146515 A Uncontrolled Copy
Two-YearLimitedWarranty(USandCanadaOnly)
Two-Year Limited Warranty (US and Canada Only)
Powerware9Corporation warrants the electronics of the USB module to be free from defects in material and workmanship
for a period of two years from Date of Purchase. If, in Powerware Corporation’s opinion, the electronics fails to meet its
published specifications due to a defect in material and workmanship covered by this warranty, Powerware Corporation
will repair or replace the warranted Unit at no cost to the customer for parts and labor.
Equipment supplied by Powerware Corporation, but not manufactured by Powerware Corporation, is warranted solely by
the manufacturer of such equipment. Powerware Corporation does not warrant equipment not manufactured by
Powerware Corporation.
This warranty does not apply to any Unit that has been subject to neglect, accident, abuse, misuse, misapplication,
incorrect connection or that has been subject to repair or alteration not authorized in writing by Powerware Corporation’s
personnel. THIS WARRANTY IS THE PURCHASER’S (USER’S) SOLE REMEDY AND IS EXPRESSLY IN LIEU OF ANY
OTHER WARRANTY, AND THERE ARE NO OTHER EXPRESSED OR IMPLIED GUARANTEES OR WARRANTIES
(INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE). In no case will
Powerware Corporation’s liability under this contract exceed the value of the Unit furnished.
In no event shall Powerware Corporation be liable for any indirect, incidental, special or consequential damages.
Powerware Corporation shall not be responsible for failure to provide service or parts due to causes beyond Powerware
Corporation’s reasonable control. THIS LIMITED WARRANTY IS VOID UNLESS USER RETURNS TO POWERWARE
CORPORATION THE INCLUDED WARRANTY REGISTRATION CARD WITHIN THIRTY (30) DAYS OF DELIVERY.
Any advice furnished the Purchaser (User) before or after delivery in regard to use or application of Powerware
Corporation equipment is furnished without charges and on the basis that it represents Powerware Corporation’s best
judgement under the circumstances. The use of any such advice by the Purchaser (User) is solely and entirely at his or her
own risk.
This limited warranty applies only to equipment installed in the fifty United States of America and Canada. In other
countries, consult your local distributor.
Extended Service Coverage
A full complement of warranty extensions and enhancements are available from Powerware Corporation for your UPS.
Information pertaining to these services should be available in the shipping container along with this manual. If not, or if
you would like more information, call the Powerware Corporation Help Desk and ask about warranty services.
International Limited Warranty
Powerware Corporation warrants the electronics modules manufactured by Powerware Corporation (“Unit”) and batteries
originally packaged in the Unit or in battery packs manufactured by Powerware Corporation against defect in material or
workmanship until the earlier of: (1) 18 months from date of shipment or (2) 12 months from date of initial start-up is
performed by Powerware Corporation field personnel or field personnel authorized by Powerware Corporation to carry
out such service efforts on its behalf and provided that, startup occurs no later that 6 months after shipment. If the unit
does not function in accordance with its published specification, the user should give Powerware Corporation prompt
notice thereof and if requested by Powerware Corporation, the user shall return the warranted Unit or parts thereof to the
plant or service station designated by Powerware Corporation for inspection by Powerware Corporation. Any Unit which
may require repair and/or replacement of parts as the result of defects in workmanship or material within the stated
warranty period, will be replaced or repaired at Powerware Corporation’s option without charge for replacement parts.
The cost of shipment, duties or all other expenses associated with shipment of repaired or replaced items is for the
account of the user.
X-SlotZUSB Module User’s Guide : 05146515 A Uncontrolled Copy
9
International Limited Warranty
Powerware Corporation will not be responsible or liable for work done or expense incurred in connection with repair or
replacement except as expressly authorized by Powerware Corporation, Raleigh, NC, USA in writing. If a service engineer
is required, labor, at current published rates, and all travel and living expenses are for the account of the user.
Powerware Corporation does not warrant equipment not manufactured by Powerware Corporation including any battery
not originally packaged with the Unit or in battery packs manufactured by Powerware Corporation. The manufacturer of
all such equipment shall solely warrant that equipment and Powerware Corporation shall have no responsibility or
liability thereof.
IT IS AGREED THAT Powerware Corporation, ITS PARENT COMPANY, OR ANY OF THEIR AFFILIATES, SHALL
HAVE NO LIABILITY FOR INDIRECT, INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES, AND THAT
THERE IS NO WARRANTY, EITHER EXPRESSED OR IMPLIED BY LAW OR THE PARTIES HERETO, OTHER THAN
THOSE EXPRESSLY SET FORTH HEREIN. THIS WARRANTY DOES NOT COVER DAMAGE TO THE UNIT CAUSED
BYMISUSE,ABUSE,NEGLECT,UNAUTHORIZEDMODIFICATIONS,IMPROPERMAINTENANCE,ACCIDENTSOR
OTHER ABNORMAL CONDITIONS.
Force Majeure
Powerware Corporation shall not be liable for any delays or defaults hereunder by reason of fire, floods, acts of God, labor
troubles, accidents to machinery, delays of carriers or suppliers, inability of suppliers to supply, the impositions of
priorities, restrictions or other acts of government, or other causes beyond its reasonable control.
This Warranty shall be governed by the laws of the State of North Carolina, USA in all respects.
10
X-SlotZUSB Module User’s Guide : 05146515 A Uncontrolled Copy
Loading...