POWERSOFT Ottocanali 8K4 DSP+DANTE Powersoft_Ottocanali_QG_en_WEB.pdf

Ottocanali Series

Ottocanali

DSP+D

12K4

Ottocanali 12K4
Ottocanali 12K4 DSP+D

Ottocanali 8K4
Ottocanali 8K4 DSP+D

Ottocanali 4K4
Ottocanali 4K4 DSP+D

©2017 Powersoft
DO000202.04 R0

Quick Guide

Keep this manual

for future reference

DO000202.04_Powersoft_Ottocanali_QG_en

Data are subject to change without notice.
For latest update please refer to the English
online version available on www.powersoft-audio.com.

Table of contents

1. Important safety instructions 10

2. Ottocanali Series 11

2 : 1.Welcome 11

2 : 2.Unpacking & checking for shipping damage 11

2 : 3.Disposal of the packaging material 11

2 : 4.List of image panels 11

3. Installation 12

3 : 1.Location 12

3 : 2.Cooling 12

3 : 3.Cleaning 12

3 : 4.AC mains supply 12

3 : 5.Energy save 13

3 : 6.Remote ON/OFF (standby mode) 13

3 : 7.Precautions regarding installation 13

4. Connections 14

4 : 1.Signal grounding 14

4 : 2.Analog audio input connections 14

4 : 2.1. AUX SEL. IN: Analog input selection 14
4 : 2.2. PWS OUT: Built-in auxiliary power supply 14

4 : 3.Digital audio input connections 14

4 : 3.1. Input selection and Backup policy 14

4 : 4.Ethernet connections 14

4 : 5.Output connections 15

4 : 5.1. Hi-Z 70V/100V operations 15

4 : 6.GPO - Alarms 15

4 : 6.1. Pilot tone monitoring 15
4 : 6.2. Output load monitoring 15

5. Attenuators 16

6. LED chart 16

7. Firmware update 16

8. Networking 17

8 : 1.IP addressing 17

8 : 1.1. IP Addressing troubleshooting 17

8 : 2.Dante™ networking 17

8 : 2.1. Redundant network configuration 17

9. Armonía Pro Audio Suite 18

9 : 1.Signal routing and DSP architecture 18

9 : 2.Purposed workflow 18

10. Warranty and assistance 19

10 : 1.Warranty 19

10 : 1.1. Return of Goods 19
10 : 1.3. Repair or replacement 19
10 : 1.4. Cost and responsibility of transport 19

10 : 2.Assistance 19

OTTOCANALI | 3

A

482

442

Ottocanali

12K4

DSP+D

76.2

88.2

365.5

382

B

1. Grip the outermost left hand side panel
and tilt it on its inner edge;

2. Carefully slide the panel and remove
the anti-dust lter.

1

2

4 | OTTOCANALI

C

Ottocanali

12K4

DSP+D

A B EC D

CH 1-2

CH 3-4

CH 5-6

CH 7-8

OFF

ON

ENERGY

SAVE

PWS OUT

ONOFF

Front

A. 24 VDC PWS OUT switch
B. Energy save DIP switches
C. Input attenuators (channels 1 to 8)
D. Multifunction LEDs (channels 1 to 8)
E. Air vent

2 3 4 5 6 7 81

Ottocanali 12K4

Ottocanali 8K4
Ottocanali 4K4

D

1 2 3

Rear

1. On/off power switch and
AC mains IEC C20 inlet

2. Fan

3. Audio outputs (channels 1-4)

4. Audio outputs (channels 5-8)

5. Audio inputs: LINE (ch. 1-8)

6. Audio inputs: AUX (ch. 1-8)

7. Fan

8. GPO - Alarms channels 1-4

9. GPO - Alarms channels 5-8

10. Remote off switch

11. Disabled (remote on switch)

12. 24 V

DC

13. AUX SEL. IN input selector

14. Multi function DIP switch ch. 1-2
(impedance, voltage, filter)

PWS OUT

CLASS3

WIRING

100V

hi-Z

70Hz

70V

lo-Z

35Hz

100V

hi-Z

70Hz

70V

lo-Z

35Hz

4

HPF On

HPF Off

HPF On

HPF Off

15. Multi function DIP switch ch. 5-6
(impedance, voltage, filter)

16. Multi function DIP switch ch. 7-8
(impedance, voltage, filter)

17. Multi function DIP switch ch. 3-4
(impedance, voltage, filter)

8765

CH1CH2CH3CH4

CH1CH2CH3CH4

CH5CH6CH7CH8

CH5CH6CH7CH8

4 NCNO 3 NC NO 2 NCNO 1 NC NO

8 NCNO 7 NC NO 6 NCNO 5 NC NO

9

1012 111314151617

OTTOCANALI | 5

E

Ottocanali

12K4

DSP+D

Ottocanali 12K4 DSP+D

Ottocanali 8K4 DSP+D
Ottocanali 4K4 DSP+D

A B D E F GC JH

CH 1-2

CH 3-4

OFF

ON

ENERGY

SAVE

PWS OUT

ONOFF

Front

A. 24 VDC PWS OUT switch
B. Energy save DIP switches
C. USB port
D. Callback to Armonía
E. Soft reset pushbutton
F. Hard reset pushbutton
G. Firmware update pushbutton
H. Output attenuators (speakers A to H)
I. Multifunction LEDs (channels 1 to 8)
J. Air vent

CALL SOFT RESET HARD RESET FW UPDATE

CH 5-6

CH 7-8

B C D E F G HA

I

F

1 2 3

1. On/off power switch and

Rear

AC mains IEC C20 inlet

2. Fan

3. Audio outputs (channels 1-4)

4. Audio outputs (channels 5-8)

5. Audio inputs: LINE (ch. 1-8)

6. Audio inputs: AUX (ch. 1-8)

7. Fan

8. GPO - Alarms channels 1-4

9. GPO - Alarms channels 5-8

10. Ethernet port / Dante™ primary

11. Ethernet port / Dante™ secondary

12. Remote off switch

13. Remote on switch

14. 24 V

15. AUX SEL. IN input selector

16. Multi function DIP switch ch. 1-2
(impedance, voltage, filter)

17. Multi function DIP switch ch. 5-6
(impedance, voltage, filter)

18. Multi function DIP switch ch. 7-8
(impedance, voltage, filter)

19. Multi function DIP switch ch. 3-4
(impedance, voltage, filter)

PWS OUT

DC

CLASS3

WIRING

100V

hi-Z

70Hz

HPF On

70V

lo-Z

35Hz

HPF Off

100V

hi-Z

70Hz

HPF On

70V

lo-Z

35Hz

HPF Off

4

CH1CH2CH3CH4

CH1CH2CH3CH4

CH5CH6CH7CH8

CH5CH6CH7CH8

16171819 11

8765

4 NCNO 3 NC NO 2 NCNO 1 NC NO

8 NCNO 7 NC NO 6 NCNO 5 NC NO

12131415

10

9

6 | OTTOCANALI

G H

INPUT

Phoenix MC 1,5/12-ST-3,81 1803675 Phoenix PC 5/ 8-STF1-7,62 1777891

OUTPUT (single ended)

I J

GPO

INPUT (link channel pairs)

CH 4

CH 3

CH 2

CH 1

Phoenix MC 1,5/12-ST-3,81 1803675

Bill of connectors

Name Plug

INPUT Phoenix MC 1,5/12-ST-3,81 1803675

OUTPUT Phoenix PC 5/ 8-STF1-7,62 1777891

GPO/ALARM Phoenix MC 1,5/12-ST-3,81 1803675

AUXILIARY Phoenix MC 1,5/4-ST-3,81 1803594

AC MAINS IEC C19

Phoenix MC 1,5/12-ST-3,81 1803675

OUTPUT (bridged)

CH 3-4

CH 1-2

Phoenix PC 5/ 8-STF1-7,62 1777891

OTTOCANALI | 7

K

70V

lo-Z

35Hz

HPF Off

100V

hi-Z

70Hz

HPF On

1 2 3 4 5 6 7 8

Ottocanali
12K4

DSP+D

Ottocanali
12K4

DSP+D

Ottocanali
12K4

DSP+D

Ottocanali
12K4

DSP+D

Ottocanali
12K4

DSP+D

Ottocanali
12K4

DSP+D

Ottocanali
12K4

DSP+D

Ottocanali
12K4

DSP+D

Low-Z High-Z 100V 70V HPF @ 35 Hz HPF @ 70 Hz

1

2

3

4

5

6

7

•

• •

• • •

• • •

• •

• • •

• • •

100V

70V

hi-Z

lo-Z

2

100V

hi-Z

70Hz

HPF On

1 2 3 4 5 6 7 8

70Hz

HPF On

35Hz

HPF Off

1

1 2 3 4 5 6 7 8

70V

100V

70V

lo-Z

hi-Z

lo-Z

35Hz

HPF Off

5

70Hz

35Hz

HPF On

HPF Off

1 2 3 4 5 6 7 8

100V

70V

100V

70V

hi-Z

lo-Z

hi-Z

lo-Z

3

6

70Hz

35Hz

70Hz

35Hz

HPF On

HPF Off

HPF On

HPF Off

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

100V

70V

100V

70V

hi-Z

lo-Z

hi-Z

lo-Z

4

70Hz

HPF On

1 2 3 4 5 6 7 8

35Hz

HPF Off

7

70Hz

35Hz

HPF On

HPF Off

1 2 3 4 5 6 7 8

L M N

RJ45

1 2 3 4 5 6 7 8

Color code (TIA/EIA-568-B) Pin

ORANGE /

WHITE

ORANGE 2

GREEN / WHITE 3

BLUE 4

BLUE / WHITE 5

GREEN 6

BROWN / WHITE 7

BROWN 8

8 | OTTOCANALI

1

Ottocanali

DSP+D

12K4

Mounting brackets

1 RU

4 4

3 3

2 2

1

1 RU

4 4

3 3

2 2

1 1

5

1

1 RU

Regulatory informations

WEEE Directive EC Declaration Of Conformity

If the time arises to throw away your product, please recycle all

possible component.

This symbol indicates that when the end-user wishes
to discard this product, it must be sent to separate
collection facilities for recovery and recycling. By
separating this product from other household-type
waste, the volume of waste sent to incinerators or
land-lls will be reduced and natural resources will
thus be conserved.

The Waste Electrical and Electronic Equipment Directive (WEEE
Directive) aims to minimise the impact of electrical and electronic
goods on the environment. Powersoft S.p.A. comply with the
Directive 2012/19/EU of the European Parliament on waste
electrical nance the cost of treatment and recovery of electronic
equipment (WEEE) in order to reduce the amount of WEEE that is
being disposed of in land-ll site.

All of our products are marked with the WEEE symbol; this
indicates that this product must NOT be disposed of with other
waste. Instead it is the user’s responsibility to dispose of their
waste electrical and electronic equipment by handing it over to
an approved reprocessor, or by returning it to Powersoft S.p.A.
for reprocessing. For more information about where you can send
your waste equipment for recycling, please contact Powersoft
S.p.a. or one of your local distributors.

Manufacturer:

Powersoft S.p.A.
via E. Conti 5
50018 Scandicci (Fi)
Italy

We declare that under our sole responsibility the products:
Model Names: Ottocanali 12K4

Ottocanali 12K4 DSP+D,
Ottocanali 8K4
Ottocanali 8K4 DSP+D
Ottocanali 4K4
Ottocanali 4K4 DSP+D
Intended use: Professional Audio Amplier

Are in conformity with the provisions of the following EC
Directives, including all amendments, and with national legislation
implementing these directives:

2014/35/EU Low Voltage Directive
2014/30/EU Electromagnetic Compatibility Directive
2011/65/EU RoHs Directive
2014/53/EU Radio Equipment Directive

The following harmonized standards are applied:

EN 55103-1: 2009 /A1: 2012
EN 55103-2: 2009 /IS: 2012
EN 60065: 2014 /AC: 2016

O

Scandicci,
February 2017

Luca Lastrucci
Managing Director

For compliance questions only: [e-mail]

OTTOCANALI | 9

Important safety instructions

EXPLANATIONS OF GRAPHICAL SYMBOLS

The triangle with the lightning bolt is used to alert the user to the risk of
electric shock.

1

CAUTION

RISK OF ELECTRICK SHOCK

DO NOT OPEN

The triangle with the exclamation point is used to alert the user to im­portant operating or maintenance instructions.

The CE-mark indicates the compliance with the low voltage and elec­tromagnetic compatibility.

Symbol for earth/ground connection.

Symbol indicating that the equipment is for indoor use only.

Symbol for conformity with Directive 2002/96/EC and Directive
2003/108/EC of the European Parliament on waste electrical and elec­tronic equipment (WEEE).

Do not use the unit at altitudes above 2000 m.

Do not use the unit in tropical environment.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT ATTEMPT TO
OPEN ANY PART OF THE UNIT. NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.

TO COMPLETELY DISCONNECT THIS APPARATUS FROM THE AC MAINS, DISCON­NECT THE POWER SUPPLY CORD PLUG FROM THE AC RECEPTACLE.

THE MAINS PLUG OF THE POWER SUPPLY CORD MUST
REMAIN READILY ACCESSIBLE.

DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE, DRIPPING OR
SPLASHING LIQUIDS. OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD
NOT BE PLACED ON THIS APPARATUS.

THE UNIT MUST BE INSTALLED IN RACK CABINETS: INSTEAD OF CONNECTING
THE AMPLIFIER TO THE POWER GRID DIRECTLY, PLUG THE AMPLIFIER’S MAINS
CONNECTIONS VIA A SECTIONING BREAKER TO A POWER DISTRIBUTION PANEL
INSIDE THE RACK CABINET.

WHEN THE UNIT IS INSTALLED IN A CABINET OR A SHELF, MAKE SURE THAT IT
HAS SUFFICIENT SPACE ON ALL SIDES TO ALLOW FOR PROPER VENTILATION (50
CM FROM THE FRONT AND REAR VENTILATION OPENINGS).

CONNECTION TO THE MAINS SHALL BE DONE ONLY BY A ELECTROTECHNICAL
SKILLED PERSON ACCORDING THE NATIONAL REQUIREMENTS OF THE COUNTRI­ES WHERE THE UNIT IS SOLD.

WARNING. THIS APPARATUS CONTAINS A NON RECHARGEABLE LITHIUM BATTE­RY (I.E. CR2032, 3V). THE BATTERY IS NOT INTENDED TO BE REPLACED BY THE
END USER. ONLY THE STAFF OF THE AUTHORIZED SERVICE CENTERS CAN AC­CESS AND REPLACE THE BATTE R Y.

WARNING: THE INTERNAL BATTERY SHALL NOT BE EXPOSED TO EXCESSIVE
HEAT SUCH AS SUNSHINE, FIRE OR THE LIKE.

Electrical energy can perform many useful functions. This unit has been engine­ered and manufactured to ensure your personal safety. But IMPROPER USE CAN
RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD.
In order not to defeat the safeguards incorporated into this product, observe
the following basic rules for its installation, use and service. Please read these
“Important Safeguards” carefully before use.

Important safety instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this equipment near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including ampliers) that
produce heat.

9. Do not defeat the safety purpose of the polarized or ground­ing-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades
and a third grounding prong. The wide blade or the third
prong are provided for your safety. If the provided plug does
not t into your outlet, consult an electrician for replacement
of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When acart is used,
use caution when moving the cart/apparatus combination to
avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long
periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.

10 | OTTOCANALI

Ottocanali Series Quick Guide

2

2 : 1.Welcome

Congratulations on buying a Powersoft Ottocanali Series

amplier!

We know you are eager to use your new Ottocanali amplier,
but please take a moment to read this quick guide and the safety
instructions. In case you have any questions, please do not hesi­tate to contact your dealer or Powersoft.

The Ottocanali Series is specically designed for installation
applications. Ottocanali Series offers smaller dimensions, lighter
weight and the traditionally amazing sound quality and reliability
of all Powersoft products.

The built in PFC (Power Factor Correction) allows awless
worldwide operation with any AC mains voltage, from 100 to 240V;
patented SRM (Smart Rails Management) technology allows
to maximize the efciency of the system and drastically reduce
power consumption at any load and usage condition. This system
automatically alters the rails working voltage according to the in­staneous power requirements of the system. A low output power
requires a lower rails voltage which in turn yields lower power
consumption while at the same time guaranteeing lightning fast
switching to full rails voltage when the system requires full power.

Ottocanali Series implements redundant power supplies for
maximum reliability even in case of system fault. In case of da­mages in one power supply, the other one is capable to maintain
the system up, guaranteeing non-stop functionality even in harsh
conditions.

Ottocanali Series is designed to work with lo-Z (from 2 �) and
with 70V/100V distributed lines: any mixed conguration of low
and high impedance output loads can be realized, making the
Ottocanali Series suitable to all application in installed sound
reinforcement systems.

Ottocanali Series encompasses three models:

 Ottocanali 12K4 delivering up to 1500 W per channel at 4�

 Ottocanali 8K4 delivering up to 1000 W per channel at 4�

 Ottocanali 4K4 delivering up to 500 W per channel at 4�

Each model is available in three versions: normal, with DSP plus
Dante™ and with DSP plus Ethernet connectivity.

2 : 2.Unpacking & checking for shipping damage

Your Powersoft product has been completely tested and in­spected before leaving the factory. Carefully inspect the shipping
package before opening it, and then immediately inspect your new
product. If you nd any damage notify the shipping company or
reseller immediately.

The box contains the following:

 1x Ottocanali Series amplier.
 2x Phoenix MC 1,5/ 4-ST-3,81 - 1803594 plug
 6x Phoenix MC 1,5/12-ST-3,81 - 1803675 plug
 2x Phoenix PC 5/ 8-STF1-7,62 - 1777891 plug
 1x IEC power cord
 1x user guide

2 : 3.Disposal of the packaging material

The protective transport packaging has been selected from
materials which are environmentally friendly for disposal and can
normally be recycled.

Rather than just throwing these materials away, please
ensure they are offered for recycling.

2 : 4.List of image panels

A. Mechanical drawings: all dimensions in millimeters
B. Front panel: how to access it
C. Ottocanali Series: Front panel description
D. Ottocanali Series: Rear panel description
E. Ottocanali Series DSP: Front panel description
F. Ottocanali Series DSP: Rear panel description
G. Input connector: wiring (single ended mode)
H. Output connector: wiring (single ended mode)
I. Alarms connector: wiring
J. Input/Output connectors: wiring (bridged mode)
K. Output load DIP switch congurations
L. RJ45 Ethernet wiring (Color code TIA/EIA-568-B)
M. Air ow and mounting brackets
N. Rack mounting constraints
O. Regulatory information

OTTOCANALI | 11

Installation

3

3 : 1.Location

Ottocanali Series ampliers are meant to be installed into rack.
In order to limit the risk of mechanical damages, the ampliers must
be xed to the rack using both frontal and rear mounting brackets.
We recommends to use eight M6 or 12-24 UNC-2B screws for
threaded holes or cage nuts.

The AC mains connection of the units should be connected to
a proper circuit breaker (refer to §3 : 4.AC ma ins supply for more
details).

Install this amplier as far as possible from radio tuners and TV
sets. An amplier installed in close proximity of such equipment
may experience noise or generic performance degradation.
Placing and using the amplier for long periods of time on heat
generating sources will affect its performance. Avoid placing the
amplier on heat generating sources.

3 : 2.Cooling

Install the amplier in a well-ventilated location: the ventilation
openings must not be impeded by any item such as newspapers,
tablecloths, curtains, etc; keep a distance of at least 50 cm from
the front and rear ventilation openings of the amplier.

All Powersoft ampliers implement a forced-air cooling system
to maintain low and constant operating temperatures. Drawn by
the internal fans, air enters from the front panel and is forced over
all components, exiting at the back of the amplier.

The amplier’s cooling system features “intelligent” variable­speed DC fans which are controlled by the heatsink temperature
sensing circuits: the fans speed will increase only when the tempe­rature detected by the sensors rises over carefully predetermined
values. This ensures that fan noise and internal dust accumulation
are kept to a strict minimum.

Should however the amplier be subject to an extreme thermal
load, the fan will force a very large volume of air through the heat
sink. In the extremely rare event that the amplier should dan­gerously overheat, sensing circuits shut down all channels until
the amplier cools down to a safe operating temperature. Normal
operation is resumed automatically without the need for user
intervention.

Ottocanali Series ampliers can be stacked one on top of the
other due to the efcient cooling system they are equipped with.

There is however a safety limit to be observed: in case a rack
with closed back panels is used, leave one rack unit empty every four
installed ampliers to guarantee adequate air ow (see Panel N, p.

14).

3 : 3.Cleaning

Always use a dry cloth for cleaning the chassis and the front
panel. Air lter cleaning should be scheduled according to the
dust levels in the amplier’s operating environment.

Disconnect the AC mains source before

attempting to clean any part of the amplifier

In order to clean the vent lters you need to remove the front
cover: never attempt to open any other part of the unit.

1. Firmly grip the outermost silver colored panel and pull outwards
at an angle, as if opening a door (seePanel B, p. 7).

2. Carefully slide the metal panel away from the chassis. When
the front panel is removed, the air lter (looking like a shiny
black plastic sponge) will be exposed.

You may use compressed air to remove the dust from lters, or
wash it with clean water: in the latter case ensure that the lter is
dry before reassembly.

3 : 4.AC mains supply

Ottocanali Series ampliers implement two universal redun­dant switching mode power supplies operating in the range from
100 V

with power switch: the approved power cord is provided (see FIG. 1).

up to 240 VAC ±10%.

AC

AC mains connection is in the rear panel through the IEC C20 inlet

FIG. 1: AC mains connection.

AC mains connections must be performed

only by professional or qualified personnel

according to local electrical authorities guidelines.

This device must be powered exclusively by
earth connected mains sockets in electrical

networks compliant to the IEC 364 or similar rules.

12 | OTTOCANALI

Powersoft suggests to plug

the Ottocanali to a 32 A rating,

C or D curve, 10 kA sectioning breaker.

3 : 5.Energy save

3 : 7.Precautions regarding installation

Energy save capabilities can be activated for each channel
pair. Four DIP switches are located on the left hand side of the
front panel (see Panel C, p. 8 and Panel E, p. 10): in order to
activate the Energy save mode for channel pair set the switches in
the bottom position.

When the Energy save mode is activate on a channel pair, the
Ottocanali enters a low power consumption idle state when no
signal activity is detected for more than 4 seconds. Normal ope­ration is resumed in a matter of milliseconds when an incoming
signal is detected on the channel pair.

TAB. 1 shows the power consumption in idle mode for non-

DSP amplifers, when the Energy save is either enabled or disabled
on all channels.

115 V

mains 230 VAC mains

Energy

Save

OFF 0.90 A 52 W 103.5 VA 0.84 A 58 W 193 VA

Current

ON 0.65 A 30 W 75 VA 0.76 A 35 W 175 VA

AC

Real

Power

Apparent

Power

Current

Real

Power

Apparent

Power

TAB. 1: Idle consumption.

Note: in caswe a pilot tone is used for checking system integrity
and line faults, the Ottocanali amplier would continuously detects
a stationary signal that prevents the the idle mode. In this condi­tion the Energy save will never activate.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK

 This device must be powered exclusively by earth connected

mains sockets in electrical networks compliant to the IEC
364 or similar rules.

 Install the unit into rack cabinet.

 A sectioning breaker between the mains connections and the

amplier should be installed inside the rack cabinet.

 Properly t the AC mains plug to the amplier inlet.

 Before powering this amplier, verify that the correct voltage

rating is being used.

 Verify that your mains connection is capable of satisfying the

power ratings of the device.

 Do not use this amplier if the electrical power cord is frayed

or broken.

 Output terminals are hazardous: wiring connection to these

terminals require installation by an instructed person and the
use of ready-made leads.

 Take care to lock the output terminal before switching the

device on.

 To avoid electrical shock, do not touch any exposed speaker

wiring while the amplier is operating.

3 : 6.Remote ON/OFF (standby mode)

Remote ON/OFF is available throurgh the proper terminals in
the rear panel: in non-DSP Ottocanali (see Panel D, p. 8) by
switching 24 V
OFF connector, the amplier can be remotely toggle between
standard operating and the standby modes.

 When a 24 V

switches to standby mode.

 When the 24 V

plier switches back on as per normal boot up operation.

In order to remotely toggle between standard operating and
the standby modes, the AC mains power must be active and the
mains button switched on.

±10% voltage (10 mA max) applied to the REM

DC

voltage is applied to REM OFF, the amplier

DC

voltage is removed from REM OFF, the am-

DC

 Do not spill water or other liquids into or on the amplier.

 No naked ame sources such as lighted candles should be

placed on the amplier.

 Do not remove the cover. Failing to do so will expose you to

potentially dangerous voltage.

 The manufacturer cannot be held responsible for damages

caused to persons, things or data due to an improper or
missing ground connection.

 Contact the authorized service center for ordinary and extra-

ordinary maintenance.

It is absolutely necessary to verify these fundamental

requirement of safety and, in case of doubt, require

an accurate check by qualified personnel.

OTTOCANALI | 13

Connections

2 3 4 5 6 7 81

PWS OUT

ENERGY

SAVE

ON

OFF

CH 1-2

CH 3-4

CH 5-6

CH 7-8

ONOFF

Make sure the power switch is off before attempting to make
any input or output connections.

By using good quality input and speaker cables, the likelihood
of erratic signal behavior is reduced to a minimum. Whether you
make them or buy them, look for good quality wires, connectors
and soldering techniques.

4 : 1.Signal grounding

PWS OUT

PWS OUT LINE input

switch

OFF ACTIVE —

ON — ACTIVE

FIG. 3: Manual procedure to switch from LINE to AUX.

4 : 3.Digital audio input connections

4

AUX

input

There is no ground switch or terminal on the Ottocanali Series
ampliers. All shield terminals of input connections are directly
connected to the chassis. This means that the unit’s signal groun­ding system is automatic. In order to limit hum and/or interference
entering the signal path, use balanced input connections.

In the interests of safety, the unit MUST always operate with
electrical safety earth connected to the chassis via the dedicated
Protective Earth

wire.

4 : 2.Analog audio input connections

Ottocanali Series ampliers implements two analog input con­nections per channel: LINE and AUX input. Input selection is made
via software or through the AUX SEL. IN switch (see §4 : 2.1. AUX

SEL. IN: Analog input selection).

Analog input is provided by means of four Phoenix MC 1,5/12­ST-3,81 1803675 connectors (see Panel D, p. 8 and Panel F,

p. 10), two for LINE input (channels 1-to-4 and 5-to-8) and two

dedicated to the AUX input (channels 1-to-4 and 5-to-8). Signal
polarity of analog input connections is shown in Panel G, p. 12.

4 : 2.1. AUX SEL. IN: Analog input selection

Ottocanali Series ampliers can switch from analog LINE in­puts to AUX inputs when a constant voltage in the 12 V
range is applied to the AUX SEL. IN connector (see Panel D, p.

8 and Panel F, p. 10). When this voltage is removed from

the AUX SEL. IN, the unit switches back from AUX inputs to LINE
inputs.

FIG. 2: AUX SEL. IN and PWS OUT connector and wirings.

4 : 2.2. PWS OUT: Built-in auxiliary power supply

The PWS OUT connector provides a 24VDC – symmetrical with
respect to ground (0.2 A max) – when enabled by the toggle switch
on the front panel (see Panel C, Panel D, p. 8 and Panel E,

Panel F, p. 10).

By wiring the PWS OUT connector to the AUX SEL. IN as
shown in FIG. 3, the front panel PWS OUT switch is enabled to
toggle between analog LINE inputs and AUX inputs: this provides
an additional manual procedure to switch from analog LINE to
AUX and vice versa.

14 | OTTOCANALI

to 30 VDC

DC

Digital input is supported via Dante™ standard protocols in

Dante equipped devices.

In Ottocanali DSP+D ampliers, Dante connectivity is suppor­ted via two Ethernet ports located on the rightmost side of the
rear panels (see Panel F, p. 10). Fast Ethernet (IEEE 802.3u,
100 Mbit/s) and Gigabit Ethernet (IEEE 802.3ab, 1Gbit/s) network
protocols are supported; Cat5e or Cat6 standard UTP twisted pair
cables shall be used for connections up to 100 meters (328 ft).

Ethernet cabling must comply to TIA/EIA-568-B and adopt the
T568B scheme pinout, as shown in Panel L, p. 14.

4 : 3.1. Input selection and Backup policy

In Ottocanali DSP+D ampliers it is possible to select among
three input signal sources per channel: analog (either LINE or AUX)
and two Dante streams (streams 1-to-8 and 9-to-16).

FIG. 4: Ottocanali DSP+D: Input selection and backup policy.

Armonía Pro Audio Suite provides an interface to select the
proper input source and manage input gain and delay of analog and
digital sources, in order to compensate transmission latency and
levels (see FIG. 4).

Furthermore Ottocanali DSP+D ampliers implement a backup
policy aimed to improve reliability against signal fault. By assigning
a bus priority to the three different input sources – analog and two
Dante streams – per channel, the system is able to automatically
switch to a reliable input connection in case of signal drop or pilot
tone mismatch.

4 : 4.Ethernet connections

Ottocanali DSP+D ampliers can be remotely controlled via an
Ethernet connection through a personal computer and Powersoft
Armonía Pro Audio Suite software. Powersoft recommend the use
of Ethernet Cat5 straight through – patch – cables with pin/pair as­signments TIA/EIA-568-B, i.e. T568B, as shown in Panel L, p. 14.

4 : 5.Output connections

CLASS 3 WIRING

CLASS3

and the use of ready made leads. Take care to secure the output
terminal before switching the device on.

single-ended wirings for lo-Z loudspeaker and Hi-Z distributed
lines connections are shown in Panel H, p. 12. Bridge-tied
connection of lo-Z loudspeaker is supported on adjacent channel
pairs 1-2, 3-4, 5-6 and 7-8; inputs must be physically paralleled as
shown in Panel J, p. 12.

loads can be realized: in order to set the load conguration, each
channel is provided by four DIP switches (refer to Panel K, p.

13). Ottocanali Series is congured to drive Lo-Z loads (Panel
K#1) by factory default.

70V/100V (Hi-Z) distributed line of louspeakers. In order to connect
any channel’s output to a 70V/100V line, the rear panel DIP switch
corresponding to the channel must be correctly set as reported in

Panel K, p. 13.

Filter) when the amplier is set to drive a distributed line to pre­vent loudspeaker transformer saturation which can considerably
degrade sound performance. The HPF can be activated by means
of the DIP switch corresponding to the channel (see Panel K, p.

13): two cutting frequency are available 35 Hz and 70 Hz.

Output terminals are hazardous: wiring connection to the­se terminals require installation by an instructed person

Output connectors are Phoenix PC 5/ 8-STF1-7,62 1777891:

Any mixed conguration of low and high impedance output

4 : 5.1. Hi-Z 70V/100V operations

Any channel of an Ottocanali Series amplier can drive

Powersoft recommends to use the built-in HPF (High Pass

4 : 6.1. Pilot tone monitoring

Thanks to the built-in DSP, the Ottocanali DSP+D ampliers
implement pilot tone detection and alert. Detecting and alerting
features are available for both input and output pilot tones on each
channel.

The detection of a mismatch in the input pilot tone parameters
(frequency and voltage level) can be used to trigger the backup
policy (refer to §4 : 3.1. Input selection and Backup policy) and
activate an alert through the general purpose output switch.

The output pilot tone detection relies on an external signal
passing through the amplier or the internal post DSP pilot tone
generator (see FIG. 4); in both cases any mismatch between the
detected signal and the set thresholds triggers the general purpo­se output switches.

4 : 6.2. Output load monitoring

Through Armonía Pro Audio Suite software it is possible to set
the thresholds on the load impedance, at given frequency, that
trigger the general purpose output of any channel of the ampliers
with DSP (see FIG. 5).

4 : 6.GPO - Alarms

The Ottocanali’s GPO – general purpose output – system

implements triggering signals to broadcast alarms.

Ottocanali Series provides a pair of paralleled general purpose
output connections per channel: one Normally Open
one Normally Closed

The connections are available on the back panel via two 12­pin Phoenix MC 1.5/12-ST-3.81 1803675 connectors for channels
1-to-4 and 5-to-8: see Panel I, p. 12 for wirings.

These contacts are used to report potentially dangerous
faults or generally unsafe operation conditions by toggling alarm
switches relative to the following events:

 No AC mains (i.e. system shutdown);

 Thermal stress: the system temperature reaches 70°C, ther-

mal protections are going to be engaged;

 Short circuit in output wiring: either the loudspeaker or the

line is in short;

 DC presence at the output: a continuously stationary signal

is present at output terminals.

Ottocanali DSP feature further monitoring on pilot tone and
output load: the GPO monitoring interface in Armonía Pro Audio
Suite software is accessible through the GPO button
located at the top right corner in the dashboard of the
selected Ottocanali DSP amplier (refer to Section 9

“Armonía Pro Audio Suite”).

NC.

NO and

FIG. 5: GPO: System monitoring interface.

OTTOCANALI | 15

Attenuators Firmware update

B C D E F G HA

CALL SOFT RESET HARD RESET FW UPDATE

PWS OUT

ENERGY

SAVE

ON

OFF

CH 1-2

CH 3-4

CH 5-6

CH 7-8

ONOFF

B C D E F G HA

CALL SOFT RESET HARD RESET FW UPDATE

PWS OUT

ENERGY

SAVE

ON

OFF

CH 1-2

CH 3-4

CH 5-6

CH 7-8

ONOFF

5

The row of potentiometers in the front panel behave differently
on non-DSP ampliers and Ottocanali DSP+D ampliers:

 In non-DSP Ottocanali ampliers, the potentiometers act

as trimmers on the input level (see Panel C, p. 8): the
input signal is muted when the trimmer is completely turned
counterclockwise; on the other hand, no attenuation is ap­plied when the trimmer is completely turned clockwise.

 In Ottocanali DSP the potentiometers attenuate the speakers

gain (see Panel E, p. 10): they modify the overall gain ap­plied to the group of ways belonging to the selected speaker.
The amount of gain attenuation (External gain) is shown in
Armonía Pro Audio Suite.

7

Firmware updates for Ottocanali DSP+D can be loa­ded via the front USB port. Updated releases of the Otto­canali DSP rmware are available on the Armonía forum
(http://www.powersoft-audio.com/en/armonia-forum).

The package contains the rmware update le whose name is
in the form:

update-version#-model.bin

(e.g. update-1.6.0.10-8ch.bin): store the rmware update le into a

USB storage device and follow these instructions:

1. Switch the amplier on and wait for the completion of the
boot sequence.

2. Plug the USB storage device with the rmware update le to
the USB port in the front panel of the amplier.

LED chart

6

Color

RED

YELLOW

GREEN

GREEN

GREEN

GREEN

GREEN

1

Even if only one channel causes thermal overload, all channels are muted and all red
LEDs are on: normal operating is restored when the temperature falls under the thermal
warning threshold.

2

Even if only one channel causes thermal warning, all yellow LEDs are on: thermal pro-

tections are engaged.

3

Only available in Ottocanali DSP.

Signal

metering

Clipping SOLID ON

-6dB SOLID ON

-12dB — —

-24dB — —

signal presence

(-60dBV)

— SOLID ON Channel ready

— BLINKING Channel muted

— BLINKING AUX inputs are selected

Lighting Description

— —

TAB. 2: Front panel LEDs chart.

Warnings

System temperature above

System temperature above

80°C1

(all channels muted)

70°C2

(thermal warning)

3

3. Keep pressed the FW UPDATE pushbutton until thefront
LED bars start blinking.

USB Key in

4. The update process lasts in 3-5 minutes. At the end the
system reboots and it is possible to extract theUSB storage
device.

16 | OTTOCANALI

Networking

8

Ottocanali DSP+D ampliers support linear daisy-chain, star
and loop network topologies; in a daisy-chained network the PC
with Armonía Pro Audio Suite must always be at one end of the
chain.

Be aware that daisy-chaining does not guarantee reliability
in production environment, since any fault may yield to network
sectioning and lost of system control.

When efciency and reliability are paramount, a redundant net­work topology is advisable. In order to exploit the Dante features,
star and open daisy-chain network topology are allowed.

8 : 1.IP addressing

Factory default network settings are DHCP/AutoIP,
inorder for the amplier platform to self-congure when connected
to an existing LAN or PC. Fixed IP policy can also be adopted and
congured through Armonía Pro Audio Suite.

If a DHCP server is not active within the network, the ampli­er platform initiates a stateless address auto-conguration (i.e.
Zero-conguration networking methodology – Zeroconf): it self
assigns a local numeric network address (of the type 169.254.x.y
– 172.31.*.* for the secondary network ifpresent– with a subnet
mask 255.255.0.0) and automatically distributes and resolves the
hostnames of networked devices. For setting a static IP address
please refer to the Armonía Pro Audio Suite user guide.

8 : 1.1. IP Addressing troubleshooting

When connecting the Ottocanali DSP+D to a network envi­ronment it may happen that Armonía Pro Audio Suite does not
discover or import the amplier.

Usually this is a problem of IP addressing: both Armonia and
the Ottocanali DSP must belong to the same subnet. If a DHCP
server is present on the network and a Ottocanali DSP amplier is
in AUTO IP, networking may become unstable.

As a rule of thumb, turn the DHCP server

on before connecting the amplifiers.

IP addressing of an Ottocanali DSP+D amplier is established
during the bootstrap: when the Ottocanali DSP amplier discovers
a DHCP server on the network during the startup, it negotiates
the networking parameters. If the Ottocanali DSP does not reveal
a DHCP server on the network during the startup it set itself in
AUTO IP mode.

8 : 2.Dante™ networking

The Dante equiped models of Ottocanali DSP+D amplier
support Dante redundant networking via the two Rj45 ports on
the rear panel:

 Primary/ETH1 is the Primary network port;

 Secondary/ETH2 is the Secondary network port.

Dante connectivity is always supported on the Primary/ETH1
Gigabit Ethernet port; the Secondary/ETH2 Gigabit Ethernet port
offers continuity of operation when a parallel redundant network
is established.

In order to implement a Dante network, a computer running
Dante Controller have to be used. Dante Controller is a software
application that manages devices on the network. Ottocanali
DSP+D ampliers are automatically discovered and displayed in
Dante Controller with the default identier
8K4-71520).

Dante networks will almost always require at least one network
switch. Redundant infrastructures may require multiple switches.
For maximum reliability, network switch shall:

 be Rated for Gigabit Ethernet;

 be Non-blocking;

 have Quality of Service (QoS) with at least four queues;

 have Diffserv (DSCP) QoS with strict priority;

 have EEE (Energy efcient ethernet) switched off.

For detailed information on setting up a switch, please refer to
the manufacturer’s documentation.

8 : 2.1. Redundant network configuration

Dante Redundancy can be set up and used between any
supporting Dante-enabled audio equipment: it works by using
two completely independent and separate networks, the Primary
Network and the Secondary Network.

To setup and use Dante Redundancy, connect the Ottoca­nali DSP+D amplier and other redundant Dante-enabled audio
equipment using duplicate Gigabit switches and Ethernet cables.
Connect your computer running Dante Virtual Soundcard and
Dante Controller, and other non-redundant Dante-enabled audio
equipment to the Primary Network.

The primary and secondary networks MUST NOT be inter­connected at any point. Make sure any computer is set to auto­matically congure its IP address.

MODELNAME-SERIAL

(e.g.

OTTOCANALI | 17

Armonía Pro Audio Suite

9

Armonía Pro Audio Suite is the default conguring interface
that allows system setting and customization of the Ottocanali
DSP+D ampliers.

Armonía can be installed on a PC running Windows (XPSP3
and higher). Freely download Armonía Pro Audio Suite from the
Armonía forum:

http://www.powersoft-audio.com/en/armonia-forum

Ottocanali DSP amplifers can connect to the PC running Ar­monía through a Fast Ethernet connection. In order to start remote
operation, the device must be discovered and imported into the
Armonía Workspace. Click on the Discover button in the Remote
entities windows, or select it from the Model list and drag it into
the Armonía Workspace.

The callback button – located on the front panel of the ampli­er – allows you to highlight the presence of the amplier into the
Armonía Workspace.

Once connected to Armonía Pro Audio Suite a double click on
the amplier icon in the Workspace will open the amplier dashbo­ard. Here it is possible to access and congure all the features of
the Ottocanali DSP.

 Advanced processing. This allows you to optimize levels

and shape the sound of the input signals. Gain and polarity
adjustment, asymmetric raised-cosine full parametric lters,
delay and mute are available on each channel routed to the
speaker section.

 Speaker equalization. Designed to manage the conguration

presets for multi-way systems, it implements FIR and IIR full
parametric lters.

 Speaker routing. Once properly grouped, the output chan-

nels are presented to the matrix as speakers – asingle row
representing a speaker (actually group of ways) – allowing a
high grade of granularity in signal processing.

 Output processing. This allows ne tuning of output signals,

aiming to optimize power delivering and loudspeaker per­formance. It provides gain and polarity adjustment, IIR and
FIR full parametric lters, delay, mute, limiting and damping
control on each output channel.

9 : 2.Purposed workflow

Once the loudspeaker layout has been dened, we suggest a
bottom-up conguration procedure that starts from the congura­tion of the transducers layout and raises toward the input selection
and the denition of the backup policy.

Shortly, the main steps to follow are:

FIG. 6: Armonía Pro Audio Suite.

9 : 1.Signal routing and DSP architecture

Signal processing on Powersoft Ottocanali DSP ampliers
accomplishes multiple functions that affect the audio signal before
power amplication; the main adjustements include gain, polarity,
delay, limiting and signal equalization; some processing are rela­ted only to particular stages, such as limiting and damping control
that are implemented on the output section only, or input priority
assignment available in the input section.

The processing architecture is composed of six sections:

 Input source selection. The input section allows you to

manage input gain and delay of analog and digital sources,
in order to compensate transmission latency and levels. Fur­thermore the Ottocanali DSP+D implement a backup policy
aimed to improve reliability against signal fault.

 Matrix. The innovative routing engine of Ottocanali DSP

allows any input to be routed to any output. The Matrix
implements a non-boolean rooting architecture allowing free
channel assignment and level adjustment.

1. Set Lo-Z and Hi-Z loads and lters on output channels.

2. Load the loudspeaker presets or manually congure the
loudspeaker layout (grouping output channels, crossovering,
limiting, speaker processing, etc.).

3. Dene the routing path and the levels of the signals from the
input channels to the active output channels (matrix).

4. Select the signal source from the input connections and
dene the backup policy (input source selection).

5. Dene GPO assignment and alarms thresholds.

18 | OTTOCANALI

Warranty and assistance

10

10 : 1.Warranty

Powersoft guarantees its manufactured products to be free from
defective components and factory workmanship for a period of time
starting from the date of purchase printed on Powersoft’s (or any of
its Authorized Dealer’s) invoice to the end customer. The standard
warranty period are:

51 months for racks ampliers.
12 month for amplier modules.

All warranty repairs and retrots must be performed at Power­soft facilities or at an Authorized Service Center at no cost for the
purchaser. Warranty exclusion: Powersoft’s warranty does not cover
product malfunctioning or failure caused by: misuse, abuse, repair
work or alterations performed by non-authorized personnel, incor­rect connections, exposure to harsh weather conditions, mechanical
damages (including shipping accidents), and normal wear and tear.
Powersoft will perform warranty services provided that the product is
not damaged during transportation.

10 : 1.1. Return of Goods

Goods can be returned to Powersoft only after they have been
granted a Return Merchandise Authorization (RMA) number to be
attached to the external packaging. Powersoft (or its Authorized
Service Center) has the right to refuse any returned good without
a RMA number.

10 : 1.2. Repair or replacement

Powersoft reserves the right to repair or replace any defective
goods covered by product warranty at its sole discretion and as
it deems best.

10 : 1.3. Cost and responsibility of transport

The purchaser (or end user/customer) is solely responsible
for all transportation costs and risks associated with sending
warranty covered goods to Powersoft or its Authorized Service
Center. Powersoft will assume full responsibility and cover all
costs incurred to send the goods back to the purchaser (or end
user/customer).

10 : 2.1. Drop off at a
Powersoft Authorized Service Centre near you

 Find a Powersoft Authorized Service Centre from the list.
 Take a note of each serial number of the units to be returned.
 Completely ll out the defect report form for each unit to be

returned.

 Send the completed defect report form to the following e-mail

addresses [e-mail] (Customer care
manager) [e-mail] (Service Team).

After having applied the aforementioned procedure, the local
service manager will provide the shipment details and the prod­uct’s warranty status.

10 : 2.1.1. In-Warranty repairs:

The service repair will be free of charge for the customer.

10 : 2.1.2. Out of Warranty Issues

 The service costs are calculated on the local rate applied from

the service centre and supervised by the Powersoft HQ

 The repair time has been set from the Powersoft HQ and it’s

equally applied in all the authorized service centre

 The unit will be evaluated by a technician, and the ser-

vice centre will provide the customer with the es­timated costs. The repair will only take place once
the customer has approved the estimated costs.
The customer will pay the shipping charges once the repair
has been completed, depending on the countries’ standard
procedures.

For any enquiries please contact Powersoft Customer care
[e-mail]

10 : 2.2. Shipping the product to
Powersoft S.p.a. for Factory service centre

 Take a note of each serial number of the units to be returned.
 Fill out completely the defect report form for each unit to be

returned.

 Send the completed defect report form to the following email

address:
[e-mail]

10 : 2.Assistance

There are no user-serviceable parts in the amplier. Refer to
qualied technical personnel for servicing. In addition to having
an in-house service department, Powersoft supports a network of
Authorized Service Centers. If your amplier needs repair, contact
your Powersoft dealer (or distributor). You can also contact the
Powersoft Technical Service department to obtain the location of
the nearest Authorized Service Center.

Powersoft offers two options for product repair:

 Drop off at a Powersoft Authorized Service Centre near you.
 Ship the product to Powersoft S.p.a. for Factory Service.

After having applied the aforementioned procedure, you will
receive an Email containing the Return Merchandise Authorization
(RMA form) for each unit returned.

All returned Powersoft units must be shipped to the following
address:

Powersoft spa

Factory service centre

Via Enrico Conti N. 13 – 15

50018 Scandicci (FI)

Italy

Phone [phone] Option 2

Email: [e-mail]

OTTOCANALI | 19

Contact Powersoft Factory service centre
Phone [phone] Option 2
Email: [e-mail]

Phone Support Hours
Monday - Friday 8.30 AM to 5.30 PM Europe time

10 : 2.2.1. Shipment from NON-CE countries

When shipping from non-CE (European Community) countries,
follow the procedure described in the TEMPORARY EXPORTA­TION / IMPORTATION PROCEDURE.

Important Note:

If the RMA# is not displayed anywhere on the outside of the
box, the shipment will be rejected and sent back to the customer.

If the returned goods from NON-CE countries do not follow the
aforementioned guidelines, the package will be rejected and sent
back to the customer.

10 : 2.3. D.O.A. Procedure

In case of a D.O.A. (Dead On Arrival) product, we kindly re­quest the customer to contact the local dealer where the product
was purchased or the Factory service centre, mentioning the serial
number of the faulty unit.

D.O.A. unit will be replaced completely without any additional
charges!

Important Note: Do not tamper with or operate the D.O.A. unit
in any ways in order to avoid any warranty issue.

Powersoft S.p.a declines any D.O.A warranty service if the
returned unit has been tampered with or misused by the customer.

20 | OTTOCANALI

Ottocanali 12K4

Ottocanali 12K4 DSP+D

Specifications

Channel Handling

Number of output channels

Number of input channels:

Analog*

Dante™** 16 (2x RJ45 redundant)

LINE 8 (2x Phoenix MC 1,5/12-ST-3,81)

AUX 8 (2x Phoenix MC 1,5/12-ST-3,81)

Lo-Z (bridgeable per ch. pair) /

Hi-Z (2x Phoenix PC 5/ 8-STF1-7,62)

8 mono

Audio

Gain (dB/voltage) 32 dB / x40 V

Frequency Response ( ±0.5 dB, 1 W @ 4 Ω) 20 Hz - 20 kHz

Crosstalk @ 1 kHz, 4 Ω load > 65 dB

THD+N (from 0.1 W to Full Power @ 4 Ω load)

DIM (from 0.1 W to Full Power @ 4 Ω load)

Input Impedance 10 kΩ Balanced

Input sensitivity @ 8 � 1.94 V / +8 dBu

Max input level 6 V / +17.8 dBu

Noise Floor (20 Hz - 20 kHz A-Weighted @ 8 Ω) < -70 dB

S/N ratio (20 Hz - 20 kHz A-Wtd @ 8 Ω amplier section) > 109 dB

Damping Factor @ 8 Ω, 100Hz > 10000

Slew Rate @ 8 �, input lter bypassed > 50 V/µs

Output high pass lter OFF / 35 Hz / 70 Hz

< 0.08%

(typical < 0.05%)

< 0.08%

(typical < 0.05%)

DSP***

AD converters

DA converters

Sample rate converter

Internal precision 40 bit oating point

Delay 2 s + 100 ms for time alignment

Equalizer

Crossover

Limiters TruePower™, RMS voltage, RMS current, Peak limiter

Damping control Active DampingControl™

Linkwitz-Riley, Bessel: 6 dB/oct to 48 dB/oct (IIR)

24 Bit Tandem™ @ 96 kHz

129 dB Dynamic Range - 0.00056 % THD+N

24 Bit Tandem™ @ 192 kHz

121 dB Dynamic Range - 0.00084 % THD+N

24 Bit @ 44.1 kHz to 192 kHz

140 dB Dynamic Range - 0.0001 % THD+N

Raised-cosine, custom FIR, parametric IIR:

peaking, hi/lo-shelving, all-pass,

band-pass, band-stop, hi/lo-pass

linear phase (FIR), hybrid (FIR-IIR), Butterworth,

Networking***

Ports 2x RJ45 ports on rear panel

Dante™ by Audinate

Protocols

Topologies Star, daisy chain, looped daisy chain, redundant stars

* Two switchable analog input connections per input channel.
** Ottocanali 12K4 DSP+D version only

Gigabit Ethernet (IEEE 802.3ab, 1 Gbit/s),
Fast Ethernet (IEEE 802.3u, 100 Mbit/s)

®

**, Dante™ redundant **,

Output Stage

Maximum output power per channel @ 2 Ω 1100 W

Maximum output power per channel @ 4 Ω 1500 W

Maximum output power per channel @ 8 Ω 850 W

Maximum output power @ 4 Ω Bridged 3000 W

Maximum output power @ 8 Ω Bridged 2200 W

Maximum output power @ Hi-Z, 70 V distributed line 1500 W

Maximum output power @ Hi-Z, 100 V distributed line 1500 W

Peak total output, all channels driven 12000 W

Maximum unclipped output voltage (Lo-Z) 150 V

Maximum output current (Lo-Z) 54 A

The power gure is calculated by driving and loading symmetrically all the channels:
uneven loads allow to achieve highest performance.

peak

peak

AC Mains Power

Power supply Dual redundant, universal switch mode

Nominal Voltage 100 - 240 V @ 50/60Hz

Operating Range 90 - 264 V

Power Factor
1/8 Max. Power @ 4 Ω

Consumption 115V 230V

Idle 30 W 0.6 A 35 W 0.8 A

1/8 Max. Power @ 4 Ω 2075 W 18.5 A 2115 W 9.7 A

1/4 Max. Power @ 4 Ω 4150 W 36 A 4230 W 18.6 A

> 0.9

Thermal

Operating temperature 0° - 35°C / 32° - 95°F

Cooling

Consumption 115V 230V

Idle 103 BTU/h 26 kcal/h 118 BTU/h 30 kcal/h

1/8 Max. Power @ 4 Ω 2141 BTU/h 540 kcal/h 1937 BTU/h 488 kcal/h

1/4 Max. Power @ 4 Ω 4283 BTU/h 1080 kcal/h 3874 BTU/h 977 kcal/h

Fan, continuously variable speed,

teperature controlled

GPO (Alarms)

Remote ON/OFF (standby) switch

One pair of NC and NO terminals per channel triggered by:

System shutdown

Thermal stress (system temperature above 70°C)

Short circuit in output wiring

DC presence at the output

Input pilot tone out of range**

Output pilot tone out of range**

Output load out of range**

Construction

Dimensions (LxWxH)

Weight 14 kg (30.8 lb)

482 mm x 382 mm x 89 mm

(19 in x 15 in x 3.5 in)

OTTOCANALI | 21

Ottocanali 8K4

Ottocanali 8K4 DSP+D

Specifications

Channel Handling

Number of output channels

Number of input channels:

Analog*

Dante™** 16 (2x RJ45 redundant)

LINE 8 (2x Phoenix MC 1,5/12-ST-3,81)

AUX 8 (2x Phoenix MC 1,5/12-ST-3,81)

Lo-Z (bridgeable per ch. pair) /

Hi-Z (2x Phoenix PC 5/ 8-STF1-7,62)

8 mono

Audio

Gain (dB/voltage) 32 dB / x40 V

Frequency Response ( ±0.5 dB, 1 W @ 4 Ω) 20 Hz - 20 kHz

Crosstalk @ 1 kHz, 4 Ω load > 65 dB

THD+N (from 0.1 W to Full Power @ 4 Ω load)

DIM (from 0.1 W to Full Power @ 4 Ω load)

Input Impedance 10 kΩ Balanced

Input sensitivity @ 8 � 1.94 V / +8 dBu

Max input level 6 V / +17.8 dBu

Noise Floor (20 Hz - 20 kHz A-Weighted @ 8 Ω) < -70 dB

S/N ratio (20 Hz - 20 kHz A-Wtd @ 8 Ω amplier section) > 107 dB

Damping Factor @ 8 Ω, 100Hz > 10000

Slew Rate @ 8 �, input lter bypassed > 50 V/µs

Output high pass lter OFF / 35 Hz / 70 Hz

< 0.08%

(typical < 0.05%)

< 0.08%

(typical < 0.05%)

DSP**

AD converters

DA converters

Sample rate converter

Internal precision 40 bit oating point

Delay 2 s + 100 ms for time alignment

Equalizer

Crossover

Limiters TruePower™, RMS voltage, RMS current, Peak limiter

Damping control Active DampingControl™

Linkwitz-Riley, Bessel: 6 dB/oct to 48 dB/oct (IIR)

24 Bit Tandem™ @ 96 kHz

129 dB Dynamic Range - 0.00056 % THD+N

24 Bit Tandem™ @ 192 kHz

121 dB Dynamic Range - 0.00084 % THD+N

24 Bit @ 44.1 kHz to 192 kHz

140 dB Dynamic Range - 0.0001 % THD+N

Raised-cosine, custom FIR, parametric IIR:

peaking, hi/lo-shelving, all-pass,

band-pass, band-stop, hi/lo-pass

linear phase (FIR), hybrid (FIR-IIR), Butterworth,

Networking***

Ports 2x RJ45 ports on rear panel

Dante™ by Audinate

Protocols

Topologies Star, daisy chain, looped daisy chain, redundant stars

* Two switchable analog input connections per input channel.

** Ottocanali 12K4 DSP+D version only

Gigabit Ethernet (IEEE 802.3ab, 1 Gbit/s),
Fast Ethernet (IEEE 802.3u, 100 Mbit/s)

®

**, Dante™ redundant **,

Output Stage

Maximum output power per channel @ 2 Ω 850 W

Maximum output power per channel @ 4 Ω 1000 W

Maximum output power per channel @ 8 Ω 600 W

Maximum output power @ 4 Ω Bridged 1700 W

Maximum output power @ 8 Ω Bridged 2000 W

Maximum output power @ Hi-Z, 70 V distributed line 1000 W

Maximum output power @ Hi-Z, 100 V distributed line 1000 W

Peak total output, all channels driven 8000 W

Maximum unclipped output voltage (Lo-Z) 90 V

Maximum output current (Lo-Z) 23 A

The power gure is calculated by driving and loading symmetrically all the channels:
uneven loads allow to achieve highest performance.

peak

peak

AC Mains Power

Power supply Dual redundant, universal switch mode

Nominal Voltage 100 - 240 V @ 50/60Hz

Operating Range 90 - 264 V

Power Factor
1/8 Max. Power @ 4 Ω

Consumption 115V 230V

Idle 30 W 0.6 A 35 W 0.8 A

1/8 Max. Power @ 4 Ω 1425 W 12.6 A 1425 W 6.6 A

1/4 Max. Power @ 4 Ω 2800 W 24.5 A 2760 W 12.3 A

> 0.9

Thermal

Operating temperature 0° - 35°C / 32° - 95°F

Cooling

Consumption 115V 230V

Idle 103 BTU/h 26 kcal/h 118 BTU/h 30 kcal/h

1/8 Max. Power @ 4 Ω 1480 BTU/h 373 kcal/h 1504 BTU/h 379 kcal/h

1/4 Max. Power @ 4 Ω 2792 BTU/h 704 kcal/h 2722 BTU/h 686 kcal/h

Fan, continuously variable speed,

teperature controlled

GPO (Alarms)

Remote ON/OFF (standby) switch

One pair of NC and NO terminals per channel triggered by:

System shutdown

Thermal stress (system temperature above 70°C)

Short circuit in output wiring

DC presence at the output

Input pilot tone out of range**

Output pilot tone out of range**

Output load out of range**

Construction

Dimensions (LxWxH)

Weight 14 kg (30.8 lb)

482 mm x 382 mm x 89 mm

(19 in x 15 in x 3.5 in)

22 | OTTOCANALI

Ottocanali 4K4

Ottocanali 4K4 DSP+D

Specifications

Channel Handling

Number of output channels

Number of input channels:

Analog*

Dante™** 16 (2x RJ45 redundant)

LINE 8 (2x Phoenix MC 1,5/12-ST-3,81)

AUX 8 (2x Phoenix MC 1,5/12-ST-3,81)

Lo-Z (bridgeable per ch. pair) /

Hi-Z (2x Phoenix PC 5/ 8-STF1-7,62)

8 mono

Audio

Gain (dB/voltage) 32 dB / x40 V

Frequency Response ( ±0.5 dB, 1 W @ 4 Ω) 20 Hz - 20 kHz

Crosstalk @ 1 kHz, 4 Ω load > 65 dB

THD+N (from 0.1 W to Full Power @ 4 Ω load)

DIM (from 0.1 W to Full Power @ 4 Ω load)

Input Impedance 10 kΩ Balanced

Input sensitivity @ 8 � 1.94 V / +8 dBu

Max input level 6 V / +17.8 dBu

Noise Floor (20 Hz - 20 kHz A-Weighted @ 8 Ω) < -70 dB

S/N ratio (20 Hz - 20 kHz A-Wtd @ 8 Ω amplier section) > 107 dB

Damping Factor @ 8 Ω, 100Hz > 10000

Slew Rate @ 8 �, input lter bypassed > 50 V/µs

Output high pass lter OFF / 35 Hz / 70 Hz

< 0.08%

(typical < 0.05%)

< 0.08%

(typical < 0.05%)

DSP**

AD converters

DA converters

Sample rate converter

Internal precision 40 bit oating point

Delay 2 s + 100 ms for time alignment

Equalizer

Crossover

Limiters TruePower™, RMS voltage, RMS current, Peak limiter

Damping control Active DampingControl™

Linkwitz-Riley, Bessel: 6 dB/oct to 48 dB/oct (IIR)

24 Bit Tandem™ @ 96 kHz

129 dB Dynamic Range - 0.00056 % THD+N

24 Bit Tandem™ @ 192 kHz

121 dB Dynamic Range - 0.00084 % THD+N

24 Bit @ 44.1 kHz to 192 kHz

140 dB Dynamic Range - 0.0001 % THD+N

Raised-cosine, custom FIR, parametric IIR:

peaking, hi/lo-shelving, all-pass,

band-pass, band-stop, hi/lo-pass

linear phase (FIR), hybrid (FIR-IIR), Butterworth,

Networking***

Ports 2x RJ45 ports on rear panel

Dante™ by Audinate

Protocols

Topologies Star, daisy chain, looped daisy chain, redundant stars

* Two switchable analog input connections per input channel.
** Ottocanali 12K4 DSP+D version only

Gigabit Ethernet (IEEE 802.3ab, 1 Gbit/s),
Fast Ethernet (IEEE 802.3u, 100 Mbit/s)

®

**, Dante™ redundant **,

Output Stage

Maximum output power per channel @ 2 Ω 450 W

Maximum output power per channel @ 4 Ω 500 W

Maximum output power per channel @ 8 Ω 250 W

Maximum output power @ 4 Ω Bridged 900 W

Maximum output power @ 8 Ω Bridged 1000 W

Maximum output power @ Hi-Z, 70 V distributed line 500 W

Maximum output power @ Hi-Z, 100 V distributed line 500 W

Peak total output, all channels driven 4000 W

Maximum unclipped output voltage (Lo-Z) 65 V

Maximum output current (Lo-Z) 15 A

The power gure is calculated by driving and loading symmetrically all the channels:
uneven loads allow to achieve highest performance.

peak

peak

AC Mains Power

Power supply Dual redundant, universal switch mode

Nominal Voltage 100 - 240 V @ 50/60Hz

Operating Range 90 - 264 V

Power Factor
1/8 Max. Power @ 4 Ω

Consumption 115V 230V

Idle 30 W 0.6 A 35 W 0.8 A

1/8 Max. Power @ 4 Ω 740 W 6.6 A 750 W 3.9 A

1/4 Max. Power @ 4 Ω 1400 W 12.4 A 1405 W 6.9 A

> 0.9

Thermal

Operating temperature 0° - 35°C / 32° - 95°F

Cooling

Consumption 115V 230V

Idle 103 BTU/h 26 kcal/h 118 BTU/h 30 kcal/h

1/8 Max. Power @ 4 Ω 801 BTU/h 202 kcal/h 839 BTU/h 211 kcal/h

1/4 Max. Power @ 4 Ω 1340 BTU/h 338 kcal/h 1340 BTU/h 338 kcal/h

Fan, continuously variable speed,

teperature controlled

GPO (Alarms)

Remote ON/OFF (standby) switch

One pair of NC and NO terminals per channel triggered by:

System shutdown

Thermal stress (system temperature above 70°C)

Short circuit in output wiring

DC presence at the output

Input pilot tone out of range**

Output pilot tone out of range**

Output load out of range**

Construction

Dimensions (LxWxH)

Weight 14 kg (30.8 lb)

482 mm x 382 mm x 89 mm

(19 in x 15 in x 3.5 in)

OTTOCANALI | 23

Powersoft S.p.A.

Via Enrico Conti, 5

50018 Scandicci (FI) Italy

Tel: [phone]

Fax: [phone]

General inquiries: [e-mail]

Sales: [e-mail]

Application & technical support: [e-mail]

Service & maintenance: [e-mail]

powersoft-audio.com

Data are subject to change without notice. For latest update please refer to the online version available on www.powersoft-audio.com