Poulan 2155, 2150PR, 1975, 2350, 2375 User Manual 2

R

Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.

1--800--554--6723

www.poulan.com

Instruction Manual

Manual de Instrucciones

Manuel d’Instructions

1950 / 1975 / 2055 / 2050 / 2075 / 2150

2155 / 2175 / 2350 / 2375 / 2150PR

LE Series

ENGLISH

ESPAÑOL

For Occasional Use Only

WARNING:

Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.

ADVERTENCIA:

Lea el manual de instrucciones y siga todas las advertencias e en­strucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.

AVERTISSEMENT:

Lire le manuel d’instructions et bien respecter tous les avertisse­ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.

Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907

CopyrightE2002 Electrolux Home Products, I

nc.

530163244 6/6/02

FRANÇAIS

IDENTIFICATION OF SYMBOLS

WARNING!

saw can be dangerous! Care­less orimproperusecancause
serious or even fatal injury.

Always wearappropriate earprotection, eye protection and head protection.

This chain

Always use two hands when operating the chain saw.

WARNING!

should be avoided; tip contact may cause the guide bar to
movesuddenly upward and backward, which may cause se­rious injury.

XX_

Measured maximum kickback value without chain brake for the bar
and chain combination on the label.

SAFETY RULES

WARNING:

spark plug wire and place wire where it can­not contact spark plug to prevent accidental
starting when setting up, transporting, ad­justing or making repairs except carburetor
adjustments.
Because a chain saw is a high-speed wood­cutting tool, special safety precautions must
be observed to reduce the risk of accidents.
Careless or improper use of this tool can
cause serious injury.

PLAN AHEAD

Read this manual carefully until you com-

S

pletely understand and can follow all safety
rules, precautions, and operating instruc­tions before attempting to use the unit.
Restrict the use of your saw to adult users

S

who understand and can follow safety
rules, precautions, and operating instruc­tions found in this manual.
Wear protective gear. Always use steel-

S

toed safety footwear with non-slip soles;
snug-fitting clothing; heavy-duty, non-slip
gloves; eye protection such as non-fog­ging, vented goggles or face screen; an
approved safety hard hat; and sound barri­ers (ear plugs or mufflers) to protect your
hearing. Regular users should have hear­ing checked regularly as chain saw noise
can damage hearing. Secure hair above
shoulder length.

Always disconnect

Read and understand the
instruction manual before
using the chain saw.

Contacting the guide bar tip with any object

Hearing

Protection

Snug
Fitting

Clothing

Safety
Shoes

Keep all parts of your body away from the

S

chain when the engine is running.
Keep children, bystanders, and animals a

S

minimum of 30 feet (10 meters) away from
the work area. Do not allow other people
or animals to be near the chain saw when
starting or operating the chain saw.
Do not handle or operate a chain saw when

S

you are fatigued, ill, or upset, or if you have
taken alcohol, drugs, or medication. You
must be in good physical condition and men­tally alert. Chain saw work is strenuous. If
you have any condition that might be aggra­vated by strenuous work, check with your
doctor before operating a chain saw.

Safety Hat

Eye
Protection

Heavy Duty
Gloves

Safety Chaps

2

Carefully plan yoursawing operation in ad-

S

vance. Do not start cutting until you have a
clear work area, secure footing, and, if you
are felling trees, a planned retreat path.

OPERATE YOUR SAW SAFELY

Donot operate achain saw with one hand.

S

Serious injury to the operator, helpers, by­standers or any combination of these per­sons may result from one-handed opera­tion. A chain saw is intended for
two-handed use.
Operate the chain saw only in awell-venti-

S

lated outdoor area.
Do not operate saw from a ladder or in a

S

tree.
Make sure the chain will not make contact

S

with any object while starting the engine.
Never try to start the saw when the guide
bar is in a cut.
Do not put pressure on the saw at the end

S

of the cut. Applying pressure can cause
you to lose control when the cut is com­pleted.
Stop the engine before setting the saw

S

down.
Do not operate a chain saw that is dam-

S

aged, improperly adjusted, or not com­pletely and securely assembled. Always
replace bar, chain, hand guard, or chain
brake immediately if it becomes damaged,
broken or is otherwise removed.
With the engine stopped, hand carry the

S

chain saw with the muffler away from your
body, and the guide bar and chain to the
rear, preferably covered with a scabbard.

MAINTAIN YOUR SAW IN GOOD
WORKING ORDER

Have all chain sawservice performed by a

S

qualified service dealer with the exception
of the items listed in the maintenance sec­tion ofthis manual. Forexample, ifimprop­er tools are used to remove or hold the fly­wheel when servicing the clutch, structural
damage to the flywheel can occur and
cause the flywheel to burst.
Make certain the saw chain stops moving

S

when the throttle trigger is released. For
correction, refer to CARBURETOR AD­JUSTMENTS.
Never modify your saw in any way.

S

Keep the handles dry,clean, and free of oil

S

or fuel mixture.
Keep fuel and oil caps, screws, and fas-

S

teners securely tightened.
Use only PoulanRaccessories and re-

S

placement parts as recommended.

HANDLE FUEL WITH CAUTION

Do not smoke while handling fuel or while

S

operating the saw.
Eliminate all sources of sparks or flame in

S

the areas where fuel is mixed or poured.
There should be nosmoking, open flames,
orworkthat could cause sparks. Allow en­gine to cool before refueling.
Mix and pour fuel in an outdoor area on

S

bare ground; store fuel in a cool, dry, well
ventilated place; and use an approved,

marked container for all fuel purposes.
Wipe up all fuel spills before starting saw.
Move at least 10 feet (3 meters) from fuel-

S

ing site before starting engine.
Turn the engine off and let saw cool in a

S

non-combustible area, not on dry leaves,
straw, paper, etc. Slowly remove fuel cap
and refuel unit.
Store the unit and fuel in an area where fuel

S

vapors cannot reach sparks or open
flames from water heaters, electric motors
or switches, furnaces, etc.

KICKBACK

WARNING:

can result in serious injury. Kickback is the
backward, upward or sudden forward motion
of the guide bar occurring when the saw
chain near the upper tip of theguide bar con­tacts any object such as a log or branch, or
when the wood closes in and pinches the
sawchain in the cut. Contacting a foreign ob­ject in the wood can also result in loss of
chain saw control.

Rotational Kickback can occur when the

S

moving chain contacts an object at the up­per tip of the guide bar. This contact can
cause the chain to dig into the object,
which stops the chain for an instant. The
result is a lightning fast, reverse reaction
which kicks the guide bar up and back to­ward the operator.
Pinch-Kickback can occur when the the

S

wood closes in and pinches the moving
saw chain in the cut along the top of the
guide bar and the saw chain is suddenly
stopped. This sudden stopping of the
chain results in a reversal of the chain
force used to cut wood and causes the
sawtomoveintheopposite direction ofthe
chain rotation. The saw is driven straight
back toward the operator.
Pull-In can occur when the moving chain

S

contacts a foreign object in the wood in the
cut along the bottom of the guide bar and the
sawchainis suddenly stopped. This sudden
stopping pulls the saw forward and away
fromtheoperatorand could easily cause the
operator to lose control of the saw.

Avoid Pinch--Kickback:

Be extremely aware of situations or ob-

S

structions that can cause material to pinch
the top of or otherwise stop the chain.
Do not cut more than one log at a time.

S

Do not twist the saw as the bar is with-

S

drawn from an undercut when bucking.

Avoid Pull--In:

Always begin cutting with the engine at full

S

speed and the saw housing against wood.
Use wedges made of plastic or wood.

S

Never use metal to hold the cut open.

Avoid kickback which

Kickback Path

3

Avoid Obstructions

Clear The Working Area

REDUCE THE CHANCE OF
KICKBACK

Recognize that kickback can happen.

S

With a basic understanding of kickback,
you can reduce the element of surprise
which contributes to accidents.
Never let the moving chain contact any ob-

S

ject at the tip of the guide bar.
Keep the working area free from obstruc-

S

tionssuchas othertrees,branches,rocks,
fences, stumps, etc. Eliminate or avoid
any obstruction that your saw chain could
hit while you are cutting. When cutting a
branch, do not let the guide bar contact
branch or other objects around it.
Keep your saw chain sharp and properly

S

tensioned. A loose or dull chain can in­crease the chance of kickback occurring.
Follow manufacturer’s chain sharpening
and maintenance instructions. Check ten­sion at regular intervals with the engine
stopped, never with the engine running.
Make sure the chain brake nuts are se­curely tightened after tensioning the chain.
Begin and continue cutting at full speed. If

S

the chain is moving at a slower speed,
there is greater chance of kickback occur­ring.
Cut one log at a time.

S

Use extreme caution when re-entering a

S

previous cut.
Do not attempt cuts starting with the tip of

S

the bar (plunge cuts).
Watch for shifting logs or other forces that

S

could close a cut and pinch or fall into
chain.
Use the Reduced--Kickback Guide Bar

S

and Low--Kickback Chain specified for
your saw.

MAINTAIN CONTROL

Stand to the
left of the saw

Thumb on
underside of
handlebar

Never reverse
hand positions

Elbow locked

Thumb on underside of
handlebar

Keep a good, firm grip on the saw with both

S

hands when the engine is running and
don’t let go. A firm grip will help youreduce
kickback and maintain control of the saw.
Keep the fingers of your left hand encir­cling and your left thumb under the front
handlebar. Keep your right hand com­pletely around the rear handle whether
your are right handed or left handed. Keep
your left arm straight with the elbow
locked.
Position your left hand on the front handle-

S

bar so it is in a straight line with your right
hand on the rear handle when making
bucking cuts. Never reverse right and left
hand positions for any type of cutting.
Stand with your weight evenly balanced on

S

both feet.
Stand slightly to the left side of the saw to

S

keep your body from being in a direct line
with the cutting chain.
Do not overreach. You could be drawn or

S

thrown off balance and lose control of the
saw.
Donot cut above shoulder height. It is diffi-

S

cult to maintain control of saw above
shoulder height.

KICKBACK SAFETY FEATURES

WARNING:

are included on your saw to help reduce the
hazard of kickback; however, such features
will not totally eliminate this danger. As a
chain saw user, do not rely only on safety de­vices. You must follow all safety precau­tions, instructions, and maintenance in this
manual to help avoid kickback and other
forces which can result in serious injury.

Reduced--Kickback Guide Bar, designed

S

with a small radius tip which reduces the
size of the kickback danger zone on the
bar tip. A Reduced--Kickback Guide Bar
has been demonstrated to significantly re­duce the number and seriousness of kick­backs when tested in accordance with
safety requirements for gasoline powered
chain saws as set by ANSI B175.1.

The following features

4

Reduced Kickback Symmetrical Guide Bar

Small Radius Tip

Symmetrical Guide Bar

Low--Kickback Chain, designed with a

S

contoured depth gauge and guard link
which deflect kickback force and allow
wood to gradually ride into the cutter. Low-­Kickback Chain has met kickback per­formance requirements when tested on a
representative sample of chain saws be­low 3.8 cubic inch displacement specified
in ANSI B175.1.

Low---Kickback

Chain

Contoured Depth Gauge

Large Radius Tip

Elongated Guard Link

Deflects
kickback force
and allows wood
to gradually ride
into cutter

caused by allowing contact of the bar tip in the
danger zone with any hard object. Kickback
can also be caused by pinching the saw chain
along the top of the guide bar. This action may
push the guide bar rapidly back toward the op­erator. Either of these events may cause you
to lose control of the saw which could result in
serious injury or even death. D O NOT RELY
UPON ANY OF THE DEVICES BUILT INTO
YOURSAW. YOU SHOULDUSETHESAW
PROPERLY AND CAREFULLY TO AVOID
KICKBACK. Reduced--kickback guide bars
and low--kickback saw chains reduce the
chance and magnitude of kickback and are
recommended. Your saw has a low kickback
chain and bar as original equipment. Repairs
on a chain brake should be made by an autho­rized servicing dealer. Take your unit to the
place of purchase if purchased from a servic­ing dealer, or to the nearest authorized master
service dealer.

S

S

S

angle (CKA)listedonyoursaw and listed in the

Can Obstruct Material

Not a Low --- Kickback Chain

Front Hand Guard, designed to reduce the

S

chanceof yourleft hand contacting the chain
if your hand slips off the front handlebar.
Position of front and rear handlebars, de-

S

signed with distance between handles and
“in-line” with each other. The spread and
“in-line” position of the hands provided by
this design work together to give balance
and resistance in controlling the pivot of
the saw back toward the operator if kick­back occurs.

CHAIN BRAKE AND CKA ANGLE

Chain Brake, designed to stop the chain in

S

the event of kickback.

WARNING:

RESENT AND YOU SHOULD NOT AS­SUME THAT TH E CHAIN BRAKE WILL
PROTECTYOU IN THE EVENT OFA KICK­BACK. Kickback is a lightning fast action
which throws the bar and rotating chain back
and up toward the operator. Kickback can be

WE DO NOT REP-

CKA table below represents angle of kickback
your bar and chain combinations will have
when tested in accordance with CSA (Cana­dian Standards Association) and ANSI stan­dards. When purchasing replacement bar and
chain, considerations should be given to the
lower CKA values. Lower CKA values repre­sent safer angles to the user,higher values in­dicate more angle and higher kick energies.
Computed angles represented indicate total
energyandangleassociated withoutactivation
of the chain brake during kickback. Activated
anglerepresentschain stopping time relative to
activation angle of chain break and resulting
kick angle of saw. In all cases lower CKA val­ues represent a safer operating environment
for the user.
The following guide bar and chain combina­tions meet kickback requirements of CSA
Standards Z62.1, Z62.3, & ANSI B175.1
when used on saws listed in this manual.
Use of bar and chain combinations other
than those listed is not recommended and
may not meet the CKA requirements per
standard.

Computed kickback angle (CKA) Table

LE SERIES

MODEL

1950/1975/2050

2055/2075/

2150/2150PR

2155/2175/

2350/2375

BAR

P/N Length CHAIN P/N

952044368 14!

952044370

952044418

16!

18!

952051209

952051211

952051338

Tipcontactinsome cases maycausealight­ning fast reverse REACTION, kicking guide
bar up and back toward operator.
Pinching the saw chain along the top of the
guide bar may push the guide bar rapidly
back toward the operator.
Either of these reactions may cause you to
lose control of the saw which could result in
serious injury. Do not rely exclusively upon
devices built into your saw.

WARNING:

Computed kickback

CKA without chain brake

24

_

19

_

14

_

5

NOTE:

r

mercial logging, a chain brake is required
and shall not be removed or otherwise dis­abled tocomply with Federal OSHA Regula­tions for Commercial Logging.

SAFETY NOTICE:

through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or
abnormal swellings. Prolonged use in cold
weather has been linked to blood vessel
damage in otherwise healthy people. If
symptoms occur such as numbness, pain,
loss of strength, change in skin colorortexture,
or loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek
medical attention. An anti-vibration system
does not guarantee the avoidance of these
problems. Users who operate power tools on
a continual and regular basis must monitor
closely their physical condition and the
condition of this tool.

SPECIALNOTICE:

with a temperature limiting muffler and spark
arresting screen which meets the
requirements of California Codes 4442 and

4443. All U.S. forest land and the states of
California, Idaho, Maine, Minnesota, New
Jersey, Oregon, and Washington require by
law that many internal combustion engines
tobeequipped with asparkarresting screen.
If you operate a chain saw in a state or locale
where such regulations exist, you are legally
responsible for maintaining the operating
condition of these parts. Failure to do so is
a violation of the law. Refer to the SERVICE
section for maintenance of the spark
arresting screen.

FailuretofollowallSafety RulesandPrecau­tions can result inserious injury. If situations
occur which are not covered in this manual,
use care and good judgement. If you need
assistance, contact your authorized service
dealer or call 1-800--554--6723.

ST ANDARDS:

writer’s Laboratories, Inc., in accordance with:
ANSI B175.1--2000 American National

Standards for Gasoline--Powered Chain
Saws -- Safety Requirements
CSA Z62.1--1995 Chain Saws -- Occupa­tional Health and Safety
CSA Z62.3--1996 Chain Saw Kickback Oc­cupational Health and Safety

If this saw is to be used for com-

Exposure to vibrations

Yoursaw isequipped

This saw is listed by Under-

ASSEMBLY

Protective gloves (not provided) should be
worn during assembly.

ATTACHINGTHE BAR&CHAIN

already attached)

WARNING:

repeat all steps to ensure your saw isproperly
assembled and all fasteners are secure. Al­ways wear gloves when handling the chain.

If received assembled,

(If not

Thechain is sharp and can cut you even when
it is not moving!

Loosen and remove the chain brake nuts

S

and the chain brake from the saw.
Remove the plastic shipping spacer (if

S

present).

Location of shipping space

Chain Brake

Chain Brake

An adjusting pin and screw is used to adjust

S

the tension of the chain. It is very important
whenassemblingthebar,thatthepinlocated
on the adjusting screw aligns into a hole in
the bar. Turning the screw will move the ad­justment pin up and down the screw.Locate
this adjustment before you begin mounting
the bar onto the saw . See illustration below.

Adjustment located on Chain Brake

Turn the adjusting screwby hand counter-

S

clockwise until the adjusting pin just
touches the stop. This should allow the pin
to be near the correct position.
Slide guide bar behind clutch drum until

S

guide bar stops against clutch drum
sprocket.

Carefully remove the chain from the pack-

S

age. Hold chain with the drive links as
shown.

CUTTERS MUST FACE IN

DIIRECTION OF ROTATION

Nuts

Bar Tool

Inside view of
Chain Brake

Mount the Bar

Tip of
Bar

6