Page 1
pottery barn kids
BERKELEY CHANGING TABLE
! WARNING: FALL HAZARD - To prevent death or serious
injury from falls, always keep child within arm’s reach.
•
Read all instructions before use of the changing table. KEEP INSTRUCTIONS FOR FUTURE USE.
• Before each use check the changing table for damage, loose parts, or sharp edges. DO NOT use the
changing table if it is damaged or broken.
• Set up this table to be level, stable, and structurally sound.
• This changing table may be used with or without a pad. The only pad approved for use with it is the
Contour Changing Pad available for purchase from pottery barn kids. This pad is designed to be used in
a space of at least 810 mm x 400 mm (32 inches x 16 inches). If used, place it within the rail-bounded
changing area of the changing table.
• NEVER LEAVE THE CHILD UNATTENDED and always use the restraining system.
This changing table is intended for use with children weighing up to 50 pounds.
PRE-ASSEMBLY:
• Please read all instructions before beginning assembly. The illustrations provided allow for easier assembly when
used in conjunction with the assembly instructions. Keep instructions for future use.
• For your safety and ease, assembly b y tw o adults is re commend ed.
• Remove all parts and hardware from box and lay out on a carpeted or scratch-fee work surface, as this will avoid
damaging any parts during assembly. The shipping box provides and ideal work surface. Do not dispose of any
contents until assembly is completed to avoid accidentally discarding email parts or hardware.
• Use the parts and hardware lists to identify and separate each of the pieces included.
• Note: Do not fully tighten all bolts until all parts are in place. Failure to follow these instructions may cause the bolts to
misalign during assembly.
• The use of power tools for assembly is not recommended. Power tools can damage hardware or split wood.
P ARTS INCLUDED:
(A) Changing Table Base - 1pc
(B) Changing Table Topper - 1pc
(C) Leg - 4pcs
HARDWARE ENCLOSED:
6x15mm Screw - 6pcs
(D
(E) Mending Plate
TOOLS REQUIRED
94x20x10mm - 2pcs
:
Phillips head screwdriver (not included)
B
Page 1/4
A
C
Page 2
ASSEMBLY INSTRUCTIONS:
1. Lay the Changing Table Base (A) down on a soft surface. Attach the Legs (C) to the bottom of the Changing
Table Base (A). (Fig 1).
(Fig.1)
A C
2. Turn the Changing Table Base (A) upright. Pull out all the drawers. The wooden knobs are pre-attached at the
back of drawer fronts. Remove knobs using a Phillips head screwdriver (not included) (Fig. 2).
(Fig.2)
A
Page 2/4
Page 3
3. Fasten knobs to drawers with knobs facing out using Phillips Head screwdriver. (See Fig. 3).
(Fig.3)
4. Carefully place the Changing Table Topper (B) on Changing Table Base (A), as shown in figure 4. Align the
pre-drilled holes of the Changing Table Topper (B) to the pre-drilled holes at the back of the Changing Table
Base (A). Fasten Mending plate (E) to the Changing Table Topper (B) and Changing Table Base (A) using (3)
Screws (D). Tighten with Phillips head screwdriver. Repeat with second Mending plate (E).
(Fig.4)
D
5. To fasten restraint strap, insert the buckle as shown in Figure 5. To release, press inward on the tabs.
(Fig. 5)
To Fasten
To Release
6. As a safety precaution, please follow the instructions enclosed to secure the changing table to the wall
using tipping-restraint kit included.
Page 3/4
Page 4
7. If the piece does not sit level, determine which corner does not touch the ground correctly. With two people
follow these steps:
• Carefully elevate the item slightly to provide access to the levelers attached to the bottom.
• Turn the levelers in a counter-clockwise direction or clockwise direction as needed.
• Gently set down the piece and check stability.
• Repeat steps until the furniture sits firmly on the ground. (See Fig.6)
(Fig.6)
CARE INSTRUCTIONS:
• Dust often using a clean, soft, dry lint-free cloth.
• Blot spills immediately, and wipe with a clean, damp, cloth.
• We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our lacquered finish.
• Check fasteners periodically for tightness. DO NOT over tighten. This may cause distortion or breakage.
• Parents should ensure a safe environment for the child by checking regularly, before placing the child in the
product, that every component is properly and securely in place.
stores
Thank you for your purchase
| catalog | www.potterybarnkids.com
USA 1.800.290.8181
Page 4/4
Loading...