Pottery Barn Anderson Dresser Assembly Instruction

pottery barn kids

ANDERSON DRESSER

IMPORTANT SAFETY INSTRUCTIONS:
Please read all instructions carefully before assembling.
For your safety, assembly by two adults is recommended.

PARTS INCLUDED:
(A) Dresser – 1pc

(B) Bun Foot-– 4pcs

PRE-ASSEMBLY:

• Remove all parts and hardware from the box and lay out on a clean, carpeted, or scratch-free work
surface, as this will avoid damaging any parts during assembly. The shipping box provides an ideal work
surface. Do not dispose of any contents until assembly is completed to avoid accidentally discarding small
parts or hardware.

• Use the parts and hardware lists above to identify and separate each of the pieces included.

• The illustrations provided allow for easier assembly when used in conjunction with the assembly

instructions.

• Note: Do not fully tighten all bolts until all parts are in place. Failure to follow these instructions may
cause the bolts to misalign during assembly.

• If using power tools to aid in assembly please use caution. Power tools can damage hardware or split
wood.

ASSEMBLY INSTRUCTIONS:

1. Place the Dresser (A) on its back on a clean, carpeted, scratch-free work surface.

2. Thread the (4) Bun Feet (B) into the inserted nuts located on bottom of the piece by turning the Bun Feet

(B) clockwise.

3. Turn the Dresser (A) upright. Adjust the adjustable levelers on the bottom of the Bun Feet (B) by

loosening or tightening them, so the Dresser (A) sits evenly on floor, if required.

A.

B.

A.

B.

B.

B.

B.

CARE INSTRUCTIONS:

• Dust with a clean, soft cloth.

• Bolt spills immediately, and wipe with a clean, damp, cloth.

• We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our lacquered

finish.

stores | catalog | www.potterybarnkids.com

Thank you for your purchase.

USA 1.800.290.8181

pottery barn kids

TIP RESTRAINT KIT

WARNING: This product is only a deterrent. It is not a substitute for proper adult supervision.
Young children may be injured by tipping furniture and the use of a tipping restraint is highly recomm ended.

When properly installed, this restraint could provide protection against the unexpected tipping of furniture. We
recommend mounting this restraint to a wall stud.
All Parts and Hardware are included in the hardware pack

PARTS INCLUDED

HARDWARE NEEDED

Plastic Restraint

Plastic Wall Brackets
Note: For safe mounting it is essential to use the proper hardware for your wall type. The included hardware is

for drywall or stud mounting only. For other wall types (ie: plaster, concrete, brick…) please consult your
local hardware store.

1. Locate a wall stud behind your furniture. Position a plastic wall bracket on the stud approximately 1” below
the top of the furniture. Mark and drill pilot hole into the center of the stud with a 3/32” drill bit. Attach a
plastic wall bracket to the stud with the long screws provided.

2. On the back of the furniture, a plastic wall bracket will need to be attached to the furniture frame at the top.
To do this, temporarily move the furniture into its final position and mark the location of the plastic wall
bracket on the furniture frame. Move the furniture away from the wall and place a plastic wall bracket on the
mark. Mark and drill holes for screws with 3/32” drill bit. Attach the plastic wall bracket to the furniture with
the short screws provided.

3. Move the furniture into this final position, taking care to line up the wall’s plastic wall bracket with the
furniture’s plastic wall bracket. Thread a plastic restraint through the plastic wall bracket, as shown in the
illustration. Tighten strap until snug. Do not over tighten.

- 1pc

- 2pcs

Long Screws 3x32mm
Short Screws 3x19mm

Plastic wall bracket

- 2pcs

- 2pcs

Long wood screw

Short wood screw

Thank you for your purchase.

stores | catalog | www.potterybarnkids.com

USA 1.800.290.8181

Plastic Restraint