POSIFLEX Business Machines LM, TM-7115, TM-7115N User Manual

LM-/TM-7115/7115N

LCD Touch Monitor

User’s Manual

Rev. B0

I. FEATURES

• Most stable 15” LCD monitor with tilt adjust for

industrial and commercial use.

• Application covers POS, Factory Automation etc.

• High quality 15” TFT LCD panel with scaling function for full screen

display

• Easy maintenance structure allowing easy cleaning

• Tilt adjustable yet robust and wobble free construction

• Recommended LCD resolution: 1024 x 768

• Resistive type extra long life touch panel in USB interface supports touch

panel function including left/right button, double click, drag & drop(For
TM-7115/7115N)

• Touch beep can be pitch adjusted/enabled/disabled by software control(For

TM-7115/7115N)

• Connect to host through VGA port plus USB port (for all models) and/or

COM port (for TM-7115/7115N’s RS232 touch model only)

• Support 2 downlink USB ports

FCC NOTICE

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a Cla ss
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against
interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever measures to correct the interference.

WARRANTY LIMITS

Warranty will terminate automatically when the machine is opened by any person other than the authorized technicians. The user
should consult his/her dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or hazard caused by improper application.

ABOUT THIS MANUAL

This manual assists the user to utilize the Touch Monitor TM-7115 & TM-7115N. This product provides exquisite touch control
capability over a stable and adjustable LCD monitor with minimal footprint.

The manufacturer of the LM-/TM-7115/7115N touch monitor heartily apologizes to the user for reserving the right to change or to
modify this manual without notice due to the rapid and constant progress and improvement on science and technology. The user
may always obtain the most up to date information through any of our web sites: http://www.posiflex.com,
http://www.posiflex.com.tw, http://www.posiflexusa.com.

© Copyright Posiflex Technology, Inc. 2010

TRADE MARKS AND SERVICE MARKS

POSIFLEX is a registered trademark of Posiflex Technology, Inc.

Other brand and product names are trademarks and registered trademarks and service marks of their respective owners.

P/N:

19690900030

Part 1

II. CARTON CONTENTS

1. Touch Monitor (Main unit + Adjustable base stand assembly)

2. User’s Manual

3. VGA cable

4. USB cable

5. Power adaptor: 12 V DC & power cord

6. Posiflex Product Information CDROM

7. Option RS232 cable

8. Option Audio cable

III. PARTS IDENTIFICATION

A.

FRONT VIEW

Main Unit

Display Screen
+ Touch Panel

Logo + Power
Indicator

B.

SIDE VIEWS

Lock/release lever

Adjustable Base
Assembly

Lock/release button to

detach the main unit

Control button area

Push in this direction
to adjust the tilt angle
of the display panel

OSD button

NXT button

“+” button

“-“ button

Option
FA-200

Power switch

Part 2

IV. INPUT / OUTPUT PORTS

12 V DC

input

VGA

input

RJ45 Jack

(option RS232 for

TM-7115)

USB (B)
(to Host)

USB (A)

(to Devices)

option

Audio input

V. AVAILABLE OPTION ITEMS

1. Audio port for multimedia application

2. Side mount upgrade kit FA-200 with MSR / Fingerprint sensor

3. Wall mount kit (WB-6000V-B)

VI. HARDWARE INSTALLATION

A. Option Multi-Media Function

When this option is ordered with the LM-/TM-7115/7115N touch monitor, the

3.5 mm diameter stereo jack and 2 internal 2W speakers with amplifiers are
already installed. This option cannot be late installed if it is not included in the
original order.

B. Option Side Mount Upgrade Kit

When a side-mount upgrade kit option such as FA-200 is
ordered with the LM-/TM-7115/7115N monitor, this option is
already installed in the delivery. No matter the kit it contains
MSR only, finger print sensor only or both options, the
connection to the LM-/TM-7115/7115N monitor is through an

internal cable in right side cover of the LCD/touch unit. Remove
the 2 circled screws in the left picture to remove the cover for side mount
upgrade kit as viewed from back of the panel.

Take out the cable inside this cover as circled in the left
picture here and connect it to connector inside the side
mount upgrade kit as arrowed in the same
picture. Gently arrange the excessive length
of this cable back in the hole and screw-fit
it back to the position originally occupied

by the cover as in the right picture. Please
reserve the cover if there is chance to have the side mount kit
removed in the future.

Part 3

C. Cable Connections

t

In order to settle the touch monitor properly in a point of sale system, all the
cable connections have to be routed through its base. Therefore, please observe
the procedures from A to C below to separate the main unit from the base
stand assembly after all cables in connection area disconnected.

Step A: Prepare a soft clean flat surface, such

as a piece of cloth on the desk to seat
the front surface of main unit

Step B: Press the Lock/Release button for

main unit detach and meantime ...

Step C: Slide the base stand assembly to the

right to separate the main unit from base

Refer to the bottom view picture of the
separated base at left, pass all cable through the dash
lined tunnel under a steel plate. Open the steel plate if
necessary by removing the 2 triangle marked screws.
Insert the rectangular marked end first when
reinstalling the steel plate.

Hook the main unit back onto base stand assembly by matching the matching
pegs to round part of matching holes and slide them down to slot part till the
rear lock/release button clicks.

C
B
A

Matching Pegs

Matching Holes

Round Par

Slot Part

Connect the VGA cable, USB cable (type B connector) and power cable to the
I/O connection area of LM-/TM-7115/7115N. Connect up to 2 USB devices to
LM-/TM-7115/7115N at the type A connectors. Please note that unlike usual
USB HUB, these USB devices won’t be recognized by the host when LM­/TM-7115/7115N is powered off.

Part 4