POSIFLEX Business Machines SD200, KP100, PD302, SD100 User Manual

Jiva Series

PD302

SD200

KP100

SD100

Optional Attachment Kits

FCC Notes:

This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.

Warranty Limits:

Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.

About This Manual:

Posiflex has made every effort for the accuracy of the content in this manual. However,
Posiflex will assume no liability for any technical inaccuracies or editorial or other
errors or omissions contained herein, nor for direct, indirect, incidental, consequential
or otherwise damages, including without limitation loss of data or profits, resulting
from the furnishing, performance, or use of this material.
This information is provided “as is” and Posiflex Inc. expressly disclaims any
warranties, expressed, implied or statutory, including without limitation implied
warranties of merchantability or fitness for particular purpose, good title and against
infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex reserves the right to alter product
designs, layouts or drivers without notification. The system integrator shall provide
applicative notices and arrangement for special options utilizing this product. The user
may find the most up to date information of the hardware from web sites:
http://www.posiflex.com or http://www.posiflex.com.tw
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex will not be responsible for any loss of data resulting from the use,
disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Inc. the publisher of this documentation.
© Copyright Posiflex Inc. 2004
All brand and product names and trademarks are the property of their respective holders.

P/N: 19000900010

User’s Manual

Rev. Original

Part 1

Programmable

GENERAL DESCRIPTION

OVERVIEW

This manual covers side mount attachment upgrade kits KP100, SD100,
SD200 and the rear top mount attachment kit PD302 for Posiflex Jiva series
terminals and the extended side mount attachment kits KP110/SD110/SD210
for the touch monitor TM4115. The rear top mount kit PD302 is a 2 line by 20
(6.0 x 9.66 mm) easy viewing characters LCD customer display. The side
mount kits KP’s and SD’s provide flexible configuration of optional security
devices with interfaces specified as tabled below.

KP100 / KP110 SD100 / SD110 SD200 / SD210

24 keys +

keypad (fixed)

Magnetic

stripe reader

Smart card

reader

Finger print

sensor

iButton reader

Numerical pad

ISO 7811 or JIS II

/ PS2 KB

PCSC 1.0 / USB

E-M type / USB

N. A.

FURTHER DETAIL OPTIONS

Items underlined below means that this item must be installed by Posiflex
authorized distributor only and never by average user. The iButton reader in
table above must be installed prior to delivery from the factory.

• Magnetic Stripe Reader choice

∗ ISO 7811 head reader for tracks 1 and 2
∗ ISO 7811 reader head for tracks 2 and 3
∗ ISO 7811 reader head for tracks 1, 2 and 3 + AAMVA + CA DMV
∗ JIS/II reader head (for KP100/110 only)

• iButton key

Note: if all devices utilizing a specific interface are omitted from the product,
that interface will not be installed in the product. Ex. KP100 containing no
finger print sensor neither smart card reader, there will be no USB interface
installed; For SD100 without the iButton reader, there will be no 9 pin D
connector.

N. A. N. A.

ISO 7811 / USB

or

PCSC 1.0 / USB
E-M type / USB

or

iButton / PS2 KB

(+ RS232)

ISO 7811 / USB

N. A.

Optical type / USB

N. A.

Part 2

INSTALLATION

1. HARDWARE INSTALLATION

A FOR SIDE MOUNT KIT (KP or SD)

Mechanical Mounting

For the side mount integrated attachment kits (KP100, KP110, SD100,
SD110, SD200, SD210) ordered with the host system like Jiva series or
TM4115 series, it is installed on the system at delivery. For separately ordered
side mount kit, it is delivered separately from the system and needs to be fixed
onto the system (however, SD200 series for Jiva 5800 series before the Jiva
5800G version is not recommended) per following instructions before use.
However, before trying to install a SD200 / SD210, please check first that
there is one free USB connector in the I/O area of the system reserved for this
purpose in the system configuration. Should there be any need for application
of a USB HUB for this connection, a self-powered type USB HUB (with its
own power adaptor) is required. However, For KP110 / SD110 / SD210
application with TM4115, please connect the attachment kit to the extension
cable in cable cover area of TM4115 and then connect the extension cable to
the appropriate port of the host system.

You may find two screw holes on back of the right side of the main unit
of Jiva series or TM4115 series. Align the upgrade unit to the right edge of the
main terminal. Insert and fasten with the two screws with split washers
included in your kit, as indicated in the picture below.

Upgrade Unit Screw Holes

The Upgrade Kit

.

Back of Jiva Series

Connection To Host

Connect the USB connector of attachment kit to one of the USB ports of
Jiva series or through cover area of TM4115. Connect the PS/2 KB connector
of KP100 / KP110 to the PS/2 KB jack in Jiva or through TM4115. When the
SD100 / SD110 is installed with iButton receptor, there will be one additional
9 pin female D connector and a pair of male/female PS/2 keyboard connectors
from the upgrade kit. Connect the D connector to the COM port for iButton
setup (and data connection). Connect the male PS/2 keyboard connector to the
keyboard port in Jiva or through TM4115 for data connection if KB interface

Part 3