POSIFLEX Business Machines TM-8115, LM-8115, TM-8315 User Manual

LM-8115 / TM-8115 / TM-8315

LCD Touch Monitor

User’s Manual

Rev. B0

I. FEATURES

• LM/TM-8115 is a stand along LCD monitor for industrial and commercial use.

• TM-8315 is a second display which suit for Posiflex POS Terminals with Gen.5

base stand.

• Application covers POS, Factory Automation etc.

• High quality 15” TFT LCD panel with scaling function for full screen display.

• TM-8315 support power supply through LCD cable from Posiflex Terminals

(Power supply need to setup from terminal and please refer to the terminal’s
manual).

• Recommended LCD resolution: 1024 x 768

• Resistive type extra long life touch panel in USB interface or RS232 interface

(option) supports touch panel function including left/right button, double click, drag
& drop

• Touch beep can be pitch adjusted/enabled/disabled by software control (for TM-

8115/TM-8315)

• USB HUB function with 2 ports for optional side mount devices (SD-400Z or KP-

300)

• Connect to host through VGA port plus USB port (for all models) and/or COM port

(for RS232 touch model only)

• Support 2 downlink USB ports

FCC NOTICE

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance w ith the
instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide reasonable pr otection against
interference when o perated in a commercial e nvironment. Operation of t his equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever measures to correct the interference.

WARRANTY LIMITS

Warranty will t erminate automatically when t he machine is o pened by any person other than the authorized technicians. The user
should consult his/her dealer for the problem happened. Warrant y voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or hazard caused by improper application.

ABOUT THIS MANUAL

This manual assists the user to utilize t he LCD Monitor LM-8115 series and the Touch Monito r TM-8115/TM-8315 series. This
product provides exquisite touch control capability over a stable and adjustable LCD monitor with minimal footprint.

The manufacturer of the LM-8115 / TM-8115 / TM-8315 touch monitor heartily apo logizes to the user for reserving the right to
change or to modify this manual without notice due to the rap id and constant progress and improvement on science and technology.
The user may always obtain the most up to date information through any of our web sites: http://www.posiflex.com,
http://www.posiflex.com.tw, http://www.posiflexusa.com.

TRADE MARKS AND SERVICE MARKS

POSIFLEX is a registered trademark of Posiflex Technology, Inc.

Other brand and product names are trademarks and registered trademarks and service marks of their respective owners.

P/N: 19690903030

 Copyright Posiflex Technology, Inc. 2011

Part 1

II. CARTON CONTENTS

1. Touch Monitor (Main unit + Adjustable base stand assembly)

2. User’s Manual

3. VGA cable

4. USB cable

5. Power adaptor & power cord(For TM/LM-8115)
(For TM-8315, please refer to the terminals manual to support power
from VGA cable)

6. Posiflex Product Information CDROM

7. Option RS232 cable

III. INSTALLATION GUIDE

TM/LM-8115

Since the monitor and stand are packaged separately,
please take out and hold the PE foams carefully and
DO NOT detach and drop it as show in the
following picture.

After take the PE foam out from the
carton, please remove the PE foam with
extra care and make sure place the
monitor and stand on a soft clean flat
surface such as table and as show in the
picture at the right side.

Please find the four holes in the top of stand.
Take the stand and align these four matching
holes to the four matching pegs which are in the
back on monitor.

After matching the stand and monitor, push the
stand to the arrowed direction as show in the right
picture. At this time, turn the monitor to the normal
position and plug the power then it can start to use.

Part 2

TM-8315

After open the carton, please take out the monitor carefully. Please place the
monitor’s bracket to the back of base stand and fasten the screws which circled
on the upper picture.

IV. PARTS IDENTIFICATION

A.

FRONT VIEW

TM/LM-8115

Main Unit

Display Screen
+ Touch Panel

Logo + Power
Indicator

Adjustable Base
Assembly

Option
SD-400Z

TM-8315

Main Unit

Display Screen
+ Touch Panel

Logo + Power
Indicator

Adjustable Base
Assembly

Option SD-400Z

Part 3

Lock/release button to

NXT button

NXT button

B.

SIDE VIEWS

TM/LM-8115

Lock/release lever

TM-8315

detach the main unit

Control button area

Push in this direction
to adjust the tilt angle
of the display panel

OSD button

“+” button

“-“ button

Power switch

Control button area

Bracket to fix on the

base stand

OSD button

“+” button

“-“ button

Power switch

Part 4

V. INPUT / OUTPUT PORTS

12 V DC

input

USB (B)
(to Host)

USB (A)

(to Devices)

VGA

input

COM

(option RS232)

VI. AVAILABLE OPTION ITEMS

1. Side mount upgrade kit SD-400Z or KP-300

2. Wall mount kit (WB-6000V-B)

VII. HARDWARE INSTALLATION

A. Option Side Mount Upgrade Kit

When a side-mount upgrade kit option such as SD-400Z is
ordered with the LM-8115 / TM-8115 / TM-8315 monitor, this
option is already installed in the delivery. No matter the kit
itself contains MSR only, finger print sensor only or both
options, the connection to the LM-8115 / TM-8115 / TM-8315
monitor is through an internal cable in right side cover of the
LCD/touch unit. Remove the 2 circled screws in the right
picture to remove the cover for side mount upgrade kit as viewed from back of
the panel.

Take out the cable inside this cover as arrowed in the right
picture here and connect it to connector inside the side
mount upgrade kit as circled in the same picture. Gently
arrange the excessive length of this cable back in the hole
and screw-fit it back to the position originally occupied by
the cover. Please reserve the cover if there is chance to
have the side mount kit removed in the future.

B. Cable Connections For TM/LM-8115

In order to settle the touch monitor properly in a point of sale system, all the
cable connections have to be routed through its base. Therefore, please observe
the procedures from A to C below to separate the main unit from the base
stand assembly after all cables in connection area disconnected.

Part 5