POSIFLEX Business Machines LM-6601 User Manual

Rev. Original

12.1” 2nd LCD Monitor

LM-6601

User’s Manual

I. FEATURES

• 12.1” LCD monitor with tilt adjust for 2

POS system

• Spill proof and easy maintenance structure allowing easy cleaning

• High quality TFT LCD panel with scaling up function for full screen

display

• Resolution: 1024 x 768

• Color depth: 262,144 colors

• Super VGA interface

• Powered through interface cable

FCC NOTICE

with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits
for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection
against interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever measures to correct the interference.

WARRANTY LIMITS

technicians. The user should consult his/her dealer for the problem happened. Warranty voids if the user does not follow the
instructions in application of this merchandise. The manufacturer is by no means responsible for any damage or hazard caused by
improper application.

ABOUT THIS MANUAL

construction for 12.1” LCD display with maximum resolution of 1024 x 768 pixels and 262,144 colors. It is powered by the host FT
series system through the interface cable.

this manual without notice due to the rapid and constant progress and improvement on science and technology. The user may
always obtain the most up to date information through any of our web sites: http://www.posiflex.com, http://www.posiflex.com.tw,
http://www.posiflexusa.com.

TRADE MARKS AND SERVICE MARKS

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

Warranty will terminate automatically when the machine is opened by any person other than the authorized

This manual assists the user to utilize the LCD Monitor LM-6601. Th os series provides adjustable robust

The manufacturer of the LM-6601 series heartily apologizes to the user for reserving the right to change or to modify

 Copyright Posiflex Technologies, Inc. 2008

POSIFLEX is a registered trademark of Posiflex Technologies, Inc..

Other brand and product names are trademarks and registered trademarks and service marks of their respective owners.

nd

display attached to FT series

P/N: 19050903010

Part 1

+

Button

II. CARTON CONTENTS

1. LCD Monitor panel unit (Main unit assembled with Stand)

2. L shape support bracket for LM-6601 onto FT system

3. User’s Manual

4. VGA Cable: 21863241710

5. Fixing Screws:10684038123 (#6-32 12L) x 2

III. PARTS IDENTIFICATION

Display Panel

Status LED

FT System Back Cover

LM-6601

OSD Button
NEXT Button

- Button

Power Switch

L Shape Support Bracket

IV. STATUS LED INDICATION

• Green: standby

• Blue: operating

Part 2

V. HARDWARE INSTALLATION

A. VGA Port Power Preparation

1. Inquire for technical support from your dealer to set the power support in
the VGA port of the FT system following the relevant Technical Manual
of the FT system. Please note that once the VGA port is no longer to be
occupied by the LM-6601, this power support must be discontinued!

B. Fix Bracket onto LM-6601

2. Unfold down the semi-circular base tongue of the
LM-6601 main unit and apply the L shape bracket
on this base tongue. Use the 2 screws in the
accessory bag to fix the bracket over the base
tongue as circled in the right picture. Note that the
slots for the screws on the bracket allow some
adjustment on position of LM-6601 for application.

C. Open Back Cover & Pole Cover of FT System

3. Refer to the User’s Manual of the FT system
about “INSTALLING BASE MOUNT KIT” to
open back cover and remove the 2 arrowed
screws to remove the pole cover. Preserve the 2
screws for the next step.

D. Install LM-6601 to FT System

4. Install the slender part of the L shape bracket to the hole for pole cover

and screw it to top
cover of FT base
tightly at the arrowed
holes as in the left
picture and result is
shown at the right.

E. Cable Connection

5. Connect the VGA cable that has both 3 x 5 D sub male ends to VGA port
at rear of LM-6601 and the VGA port of host system. Screw in the cable
to connectors at both ends.

F. Driver Installation

6. There is no need to install driver for use of LM-6601. However, the
supported display modes are tabulated at last part of this manual

Part 3