POSIFLEX Business Machines LM-2110, LM-2010 User Manual

LM

-

2010 / 2110

LCD Monitor

User’s Manual

Rev. A0

I. FEATURES

• Light weight and high luminance LCD monitor for industrial and

commercial use

• Application covers POS, POIS (Kiosk), factory Automation etc.

• High quality 10.4” TFT LCD panel with scaling up function for full screen

display

• Supports display resolution up to 800 x 600 pixels

• Tilt adjustable construction

• Spill proof and easy maintenance structure allowing easy cleaning

FCC NOTICE

installed and used in accordance with the instructions manual, may cause interference to radio
communications. It has been tested and found to comply with limits for a Class A digital device
pursuant to subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection
against interference when operated in a commercial environment. Operation of this equipment in a
residential area is likely to cause interference in which case the user at his own expense will be
required to take whatever measures to correct the interference.

WARRANTY LIMITS

than the authorized technicians. The user should consult his/her dealer for the problem happened.
Warranty voids if the user does not follow the instructions in application of this merchandise. The
manufacturer is by no means responsible for any damage or hazard caused by improper application.

ABOUT THIS MANUAL

series is a 10.4” LCD monitor of long endurance industrial standards. The LM-2010 is a upgrade
kit particularly designed for Posiflex hybrid terminal HT series host system.

reserving the right to change or to modify this manual without notice due to the rapid and constant
progress and improvement on science and technology. The user may always obtain the most up to
date information through any of our web sites: http://www.posiflex.com.tw, http:
//www.posiflex.com, http://www.posiflexusa.com.

TRADE MARKS AND SERVICE MARKS

of their respective owners.

P/N: 19670900020

This equipment generates, uses, and can radiate radio frequency energy and, if not

Warranty will terminate automatically when the machine is opened by any person other

This manual assists the user to utilize the LCD Monitor LM -2010/2110 series. This

The manufacturer of the LM-2010/2110 series heartily apologizes to the user for

 Copyright Posiflex Technologies, Inc. 2007

POSIFLEX is a registered trademark of Posiflex Technologies, Inc..
Other brand and product names are trademarks and registered trademarks and service marks

Part 1

Power Connector from

Power Connector in VGA

II. MODEL NUMBERS

LM-2110: 10.4” LCD Monitor w/ stand
LM-2010: 10.4” LCD Monitor w/ support bracket for Posiflex hybrid

terminals HT series

III. CARTON CONTENTS

1. LCD Monitor panel unit

2. Base stand (for LM-2110) or support bracket (for LM-2010)

3. Fixing screws (2x for LM-2010, 6x for LM-2110)

4. User’s Manual

5. VGA cable: 21867244100 (for LM-2110) or 21863241730 (for LM-

2010)

6. Power adaptor: ASP0P042WTB001 & power cord (for LM-2110)

IV. INSTALLATION

1. Use 2 fixing screws to fit the monitor stand
(for LM-2110) or support bracket (for LM-

2010) to the back of the LCD panel as
arrowed in the right picture. Connect the
VGA cable to the connector at back of the
LCD panel and screw in its fix screws as
circled in the same picture.

2. For LM-2110, connect the power

Cable for LM-2110

Power Adaptor

the wall socket and the LM-2110 is ready for work.

3. For LM-2010, following actions shall be taken to install it onto HT
systems with power for HT systems disconnected and also reference of
the manuals of the HT systems.
On base unit of HT systems, there must be 4 screw hole covers on top
side of its plastic top cover and the VGA cable hole cover within the
pole cover of its back cable cover as in picture below. There are 2
bridges from each screw hole cover to the HT top cover and 3 bridges
from the VGA cable hole cover to the pole cover as enlarged in the

connector at panel back end of VGA cable
to the power connector as in left picture.
Connect and screw-fix the other end of
VGA cable to the appropriate VGA port
of host system. Please check that the city
power supply specification from the wall
socket is within the operation range of the
power adaptor. Insert the power adaptor to

Part 2

accompanying drawings.

Screw Hole Cover VGA Cable Hole Cover

Bridge

HT Cable Cover Pole Cover

Screw Hole

Use proper tool to cut the bridges off with the screw hole cover and
VGA cable hole cover from the top cover and pole cover at points
indicated by each pair of arrows in the drawings. Sand/Cut smooth the
inside of the holes resulted.
In the HT system, please arrange the VGA power to be supplied
through the interface cable from the main unit through internal jumper
setting change with reference to its technical information by a qualified
technician.
Connect and screw the video interface
cable to the VGA port. The monitor
will always turn ON whenever power
is made available from the HT system.
Use 4 fixing screws to fit the bottom of
LM-2010 supporting bracket to HT
system base top as arrowed in the right
picture and have the VGA cable pass
through the VGA cable hole as circled
in the same picture.
Please note that for LM-2010 with a 2-digit system revision number,
the screw holes on support bracket base look like the below left picture
and the LM-2010 can be fixed to straight backward of the HT or PB
system. For LM-2010 with 3-digit system revision number (3rd digit

being “a”) or later, the bracket base is like the
right picture and the LM­2010 can be swiveled to
within +/- 30 degrees from
the straight backward
direction for best
installation in application

environment before fixing tight the screws.

Bridge

Part 3