POSIFLEX Business Machines TP-LT - 5815, 16280900030 User Manual

Jiva TP

/LT

–

5815

Touch / LCD POS Terminal

w/ Slim or Universal Base

FCC Notes:

This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.

Warranty Limits:

Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.

About This Manual:

Posiflex has made every effort for the accuracy of the content in this manual. However,
Posiflex will assume no liability for any technical inaccuracies or editorial or other
errors or omissions contained herein, nor for direct, indirect, incidental, consequential
or otherwise damages, including without limitation loss of data or profits, resulting
from the furnishing, performance, or use of this material.
This information is provided “as is” and Posiflex Technologies, Inc. expressly
disclaims any warranties, expressed, implied or statutory, including without limitation
implied warranties of merchantability or fitness for particular purpose, good title and
against infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex reserves the right to alter product
designs, layouts or drivers without notification. The system integrator shall provide
applicative notices and arrangement for special options utilizing this product. The user
may find the most up to date information of the hardware from web sites:
http://www.posiflex.com or http://www.posiflex.com.tw or http://www.posiflexusa.com
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex will not be responsible for any loss of data resulting from the use,
disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Technologies, Inc. the publisher of this documentation.
© Copyright Posiflex Technologies, Inc. 2007
All brand and product names and trademarks are the property of their respective holders.

P/N: 16280900030

User’s Manual

Rev.: B2

Part 1

CAUTION

ALERT TO OUR HONORABLE CUSTOMERS:

l Please always read thoroughly all the instructions and documents

delivered with the product before you do anything about it. Don’t
take any premature action before you have a full understanding of
the consequences.

l This product contains inside a Lithium battery and maybe also a

sealed type Lead acid battery if the UPS battery option is ordered.
Please always follow local environmental protection laws /
regulations for disposal of used batteries and always replace only
with battery of same type.

l If you have an UPS battery installed in the product:

² Temperature above 40°C must be strictly avoided as it

could cause termination of battery life and unexpected result
even if the battery is not in work.

² Do not power off the system just by shutting off the AC

power leaving the battery supporting the whole system till
completely exhausted. Repeatedly using it up or improper
maintenance reduces the battery life dramatically.

² Always fully recharge the battery at least once every 3

months if the battery is not connected.

² Always disconnect the UPS battery from the system if the

system is to be left OFF for more than 72 hours to prevent
possible damage. Only connect the UPS battery back right
before you are going to re-power on the system.

² Replace the battery as soon as the monitoring software

indicates the battery is out of service. Attempt to recharge a
dead battery is dangerous!

² A separate battery monitor is not required for this series.

DAILY MAINTENANCE GUIDE

For regular cleaning of the Jiva systems, please use only soft haired
brush or dry soft cloth. You may use moist soft cloth to remove stains when
necessary. Apply only proper amount of mild neutral detergent for obstinate
stains. Please note that never use Acryl dissolving solvent or Polycarbonate
dissolving solvent. You may apply ammonia-based glass cleaner only on the
screen surface.

Risk Of Explosion If Battery Is Replaced By An Incorrect Type

Dispose Of Used Batteries According To Local Regulations

Part 2

11 11 12 1 12 12 10 10 7 5 13 13 5 7 1

3 4 1 1

4 5 6 9 8 8 9

7 5 2 2

INTRODUCTION

PRODUCT PICTURES

Front Views

7

Slim Base Models

Slim Base Models Universal Base Models

Side Views

Slim Base Models

Slim Base Models Universal Base Models

Universal Base Models

10

Universal Base Models

10

Part 3

1 1 7 10 5 16 16 14 14 15 11 12 8 10

16 16 17 18 19 19 20 20 21 21 17 16 21 19 22 24 23 21 19

20 20

Rear Views

Slim Base Models Universal Base Models

Bottom Views

Slim Base 3.5” HDD Universal Base 3.5” HDD

Slim Base 2.5” HDD Universal Base 2.5” HDD

PARTS IDENTIFICATION

1. Main unit

2. Touch panel / LCD panel

3. Optional side mount kit

4. Power status indicator

5. Universal base stand

6. Optional CDROM drive

7. Slim base stand

8. Cable cover

9. Removal hollow in cable cover

10. Lock / release lever for tilt angle adjust

Part 4

11. Optional rear top mount kit PD-302

12. Lock / release button for main unit detach

13. Power switch

14. Rear connect cover

15. Power connector hole

16. Cable exit

17. 2nd cable exit

18. Auxiliary cable exit

19. Rubber feet

20. Bottom plate

21. Bottom plate fixing screw

22. 2.5” HDD window

23. 2.5” HDD bracket cover

24. 2.5” HDD bracket fixing screw

PRODUCT FEATURES

Standard Features:

a) CPU: C3 - 1.0 GHz.
b) An advanced slim or universal base design. The slim base models

support 2nd LCD display or pole mount customer display, storage room
for HDD and optional UPS battery in desktop mount application. The
universal base models support extensive features as 2nd LCD display or
pole mount customer display, storage room for power adaptor, HDD,
optional internal CD ROM drive and optional UPS battery in desktop
mount application. Also possible to be without base but with wall
mount bracket for wall mount application.

c) Support Win 2000, Win XP Pro, WEPOS and Linux environment
d) Fan control software in preloaded OS
e) High quality 15” TFT active matrix LCD panel
f) Vertical type LCD panel with easy tilt angle adjustment from 15° to

72.5°

g) Durable USB interface resistive type (leading edge Infra Red type

optional) touch panel that endures 35 million touches min. at same spot

h) Spill proof water resistant structure allowing easy cleaning
i) Easy maintenance construction
j) Various I/O ports supported, including:

1. one PS/2 KB port

2. one PS/2 mouse port

3. 4 serial ports (3 ports usable if IR touch used). All with capability
for +5V DC support by internal jumper setting change

4. one parallel port

Part 5

5. 2 USB ports

6. one LAN port 10/100 base T Ethernet

7. one external VGA monitor port

8. one IDE connector and HDD power connector for HDD in base

9. one 4 pin lock type DC 12 V power input connector

10. one UPS battery connector

11. one CR port for control over 2 cash drawers max.

12. audio ports (1 Microphone input and 2 optional slim type speakers)

k) Touch control functions: left/right button, double click, drag & draw
l) Dual display support (per OS capability)
m) VGA memory size shared from system memory up to 64 MB
n) Support high performance DDR DRAM in two modules with

maximum memory size 1GB

o) Integrated structure for side mount upgrade kits (KP-100, SD-100, SD-

200 or BC-100U) and optional top mount customer display PD-302

p) The MSR in side mount kit is with software programmable parameters

for Win 2000 or Win XP pro

q) Built-in UPS function to support the system from intermittent power

failure (battery itself is an option)

r) Accidental power off protection – The power switch is safely located

in recessed side, and it can be defined as a “ON” switch only through
software command

s) Preconditioned power up function – by alarm clock or COM port

MODEM ring or LAN

Optional Items:

Note: The underlined items in the following list means that option must be

set prior to shipment from the factory. The rest items can be set by the

dealers.
a) DDR SDRAM memory expansion up to 1GB
b) RS232 interface Infra-Red type touch panel durable for 50 million

touches min. at same spot or select to be without touch function (LT-

5815)
c) Select between slim and universal base
d) Base type select for 2.5” HDD in base
e) Integrated side mount upgrade kit among KP-100, SD-100, SD-200,

BC-100U
f) Integrated rear top mount 2 by 20 LCD customer display PD-302
g) Integrated base mount device choice among: PD-2501 or PD-2602 –

VFD pole display or PD-305 – LCD customer display or LM-6201 –

12.1” or LM-6301 – 15” 2nd LCD monitor

h) USB interface external slim type CD ROM drive or COMBO drive

Part 6