POSIFLEX KS-6615, KS-7315, KS-6617, KS-7317 User's Manual

Rev.: A0

P/N:

165609000

20

KS- 6615 / 7315 / 6617 / 7317

Fan Free Touch Terminal

w/ Slim or Super Slim Base

FCC Notes:

This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.

Warranty Limits:

Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.

About This Manual:

Posiflex has made every effort for the accuracy of the content in this manual. However,
Posiflex will assume no liability for any technical inaccuracies or editorial or other
errors or omissions contained herein, nor for direct, indirect, incidental, consequential
or otherwise damages, including without limitation loss of data or profits, resulting
from the furnishing, performance, or use of this material.
This information is provided “as is” and Posiflex Technologies, Inc. expressly
disclaims any warranties, expressed, implied or statutory, including without limitation
implied warranties of merchantability or fitness for particular purpose, good title and
against infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex reserves the right to alter product
designs, layouts or drivers without notification. The system integrator shall provide
applicative notices and arrangement for special options utilizing this product. The user
may find the most up to date information of the hardware from web sites:
http://www.posiflex.com or http://www.posiflex.com.tw or http://www.posiflexusa.com
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex will not be responsible for any loss of data resulting from the use,
disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Technologies, Inc. the publisher of this documentation.
© Copyright Posiflex Technologies, Inc. 2008
All brand and product names and trademarks are the property of their respective holders.

User’s Manual

Part 1

ALERT TO OUR HONORABLE CUSTOMERS:

l Please always read thoroughly all the instructions and documents

delivered with the product before you do anything about it. Don’t
take any premature action before you have a full understanding of
the consequences.

l This product contains inside a Lithium battery and maybe also a

sealed type Lead acid battery if the UPS battery option is ordered.
Please always follow local environmental protection laws /
regulations for disposal of used batteries and always replace only
with battery of same type.

l If you have an UPS battery installed in the product:

² Temperature above 40°C must be strictly avoided as it

could cause termination of battery life and unexpected result
even if the battery is not in work.

² Do not power off the system just by shutting off the AC

power leaving the battery supporting the whole system till
completely exhausted. Repeatedly using it up or improper
maintenance reduces the battery life dramatically.

² Always fully recharge the battery at least once every 3

months if the battery is not connected.

² Always disconnect the UPS battery from the system if the

system is to be left OFF for more than 72 hours to prevent
possible damage. Only connect the UPS battery back right
before you are going to re-power on the system.

² Replace the battery as soon as the monitoring software

indicates the battery is out of service. Attempt to recharge a
dead battery is dangerous!

² A separate battery monitor is not required for this series.

DAILY MAINTENANCE GUIDE

For regular cleaning of the KS systems, please use only soft haired
brush or dry soft cloth. You may use moist soft cloth to remove stains when
necessary. Apply only proper amount of mild neutral detergent for obstinate
stains. Please note that never use Acryl dissolving solvent or Polycarbonate
dissolving solvent. You may apply ammonia-based glass cleaner only on the
screen surface.

Risk Of Explosion If Battery Is Replaced By An Incorrect Type

Dispose Of Used Batteries According To Local Regulations

CAUTION

Part 2

5 1 3 6 11 8 9 4 2 8 9 12 5 1 3 7 10 6 2 11

4 6 13 6 7 14 11 13 21 15 17

19 20 6 13 13 7 16 6 22 2 4 13 22 13 6 22 7 15

INTRODUCTION

PRODUCT PICTURES

Front Views

w/ Gen 5 base

w/ Gen 5 base

w/ Gen 5 base

w/ Gen 5 base

w/ Gen 6 base

Side Views

10

Rear Views

7

w/ Gen 5 base

w/ Gen 6 base

w/ Gen 5 base

w/ Gen 5 base

w/ Gen 6 base

13

w/ Gen 6 base

Inside the touch open cover

w/ Gen 6 base

18

Part 3

Optional top mount upgrade kit

push button

device cable

Cable passage in bottom plate

UPS battery bracket fixing

Rubber feet with bottom plate

base mount kit e.g.

306 for Gen 5 Slim base

side mount kit e.g.

T for glossy front

400W for

Front cover of Gen 5 Slim base

Lock / release lever for tilt

Cable passage on trunk of Gen

main

28

25 29 23 27 26

Bottom Views

22

24

Gen 5 base

PARTS IDENTIFICATION

1. Main unit

2. Optional
PD­model

3. Touch panel / LCD panel

4. Optional
SD-400
surface model or SD­textured front surface model

5. Power indicator (Logo)

6. Gen 5 Slim base stand

7. Gen 6 Super Slim base stand

8. Cable cover

9. Removal hollow in cable cover

10.
(for service convenience only)

11.
angle adjust in Gen 5 Slim base

12.
6 Super Slim base

13. Lock / release button for
unit detach

14. Rear connect cover

15. Touch open cover

Gen 6 base

16.
e.g. PD-310 or PD-2604

17. Power switch

18. Brightness adjust
“+”

19. Touch open door latch

20. Brightness adjust push button “­”

21. Double deck USB ports

22. Cable exit

23. Base mount
groove (for Gen 5 Slim base)

24. Cable holder

25. Bottom plate

26.
of Gen 5 Slim base

27.
screw

28. UPS battery bracket

29.
fixing screw

Part 4

PRODUCT FEATURES

Standard Features:

a) Applicable CPU:

1. for KS-6615 only: Intel Celeron M 1.0 GHz

2. for KS-6615 / 6617: Interl Celeron M 1.5 GHz

3. for KS-7315 / 7317: Intel Celeron M 1.86 GHz or Core Duo 2.0
GHz or Core 2 Duo 2.16 GHz

b) Fan free structure with Aluminum main unit for harsh environment
c) Data storage device: SATA HDD 2.5” 40 GB in base stand or SATA

HDD 2.5” 40 GB in main unit or CF card.

d) An advanced Gen 5 slim base design that supports 2

pole mount customer display, storage room for 2.5” HDD and optional
UPS battery or a Gen 6 super slim base design that supports pole mount
customer display, storage room for 2.5” HDD and optional UPS battery.
Also possible to be without base but with wall mount bracket for wall
mount application.

e) Support WinXP Pro, WEPOS and Linux OS for KS-6615/6617; support

WinXP Pro, WEPOS and Windows Vista for KS-7315/7317 (Vista 64
bit for Core 2 Duo CPU model only)

f) High quality 15” TFT active matrix LCD panel for KS-6615 / 7315.

High quality 17” TFT active matrix LCD panel for KS-6617 / 7317

g) Brightness control by either software or hardware of 2 push buttons in

side cover

h) Vertical type LCD panel with easy tilt angle adjust from 15° to 70°
i) Durable resistive type (leading edge Infra Red type optional) touch

panel that endures 35 million touches min. at same spot

j) Spill proof water resistant structure allowing easy cleaning
k) Easy maintenance construction
l) Various I/O ports supported, including:

1. 4 serial ports with capability for +5V DC support in form of DB9
connectors.

2. one parallel port

3. 4 standard USB ports in I/O area plus 2 in side cover

4. one proprietary USB port for optional side mount kit (e.g. SD-400W)

5. one LAN port Ethernet 100/1000 Base T with LAN status indicators
on jack (green for link, orange for data transmission)

6. one external VGA monitor port

7. one CR port for control over max. 2 cash drawers

8. one Mic. in / audio line out port

9. one SATA data port plus one HDD power connector

10. one 4 pin lock type DC 12 V power input connector

nd

LCD display or

Part 5

11. one UPS battery connector

m) Touch control functions: left/right button, double click, drag & draw
n) Dual display support (per OS capability)
o) Dynamic video memory (max. 128 MB for KS-6615 / KS-6617, max.

224 MB for KS-7315 / KS-7317)

p) Support high performance DDR2 DRAM with maximum memory size

1GB for KS-6615/6617 and 2GB for KS-7315/7317 in one module

q) Integrated structure for side mount upgrade kit like SD-400W with

software programmable MSR parameters for Win XP or WEPOS

r) Built-in 2 internal 2W speakers with stereo audio amplifier
s) Built-in UPS function to support the system from intermittent power

failure (battery itself is an option)

t) Accidental power off protection – The power switch is safely located

inside a push-open cover, and it can be defined as a “ON” switch only
through software command

u) Preconditioned power up function – by alarm clock or COM port

MODEM ring or LAN

Option Items:

Note: The underlined items in the following list means that option must be

set prior to shipment from the factory. The rest can be set by the dealers.

a) DDR2 SODIMM memory expansion up to 1GB for KS-6615/6617 or

up to 2GB for KS-7315/7317

b) RS232 interface Infra-Red type touch panel durable for 50 million

touches min. at same spot
c) CF memory card reader slot
d) Integrated side mount upgrade kit:

² SD-400W/T: MSR, fingerprint reader

² or other later developed side mount upgrade kit

e) Integrated base mount device:

² PD2501 or PD2602 VFD pole display for slim base

² PD305 low profile LCD customer display for slim base

² PD306 LCD pole display for slim base

² PD7622 graphic LCD customer display for slim base

² LM-6201 12.1” 2nd LCD panel monitor for slim base

² LM-6301 15” 2nd LCD monitor for slim base

² or other later developed base mount device

f) Rear top mount device:

² PD310 LCD display or PD2604 VFD display
g) UPS battery in base
h) Preload OS
i) Wall mount kit: WB-6000VB, WB-6300, WB-6600, WB-6800

Part 6