Posiflex DT-308 User Manual

P/N: 1332090

0010

FCC Notes:

This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions manual, may cause interference to radio communications. It has been tested
and found to comply with limits for a Class A digital device pursuant to subpart J of
Part 15 of FCC Rules, which are designed to provide reasonable protection against
interference when operated in a commercial environment. Operation of this equipment
in a residential area is likely to cause interference in which case the user at his own
expense will be required to take whatever measures to correct the interference.

Warranty Limits:

Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.

About This Manual:

Posiflex Technology, Inc. has made every effort for the accuracy of the content in this
manual. However, Posiflex Technology, Inc. will assume no liability for any technical
inaccuracies or editorial or other errors or omissions contained herein, nor for direct,
indirect, incidental, consequential or otherwise damages, including without limitation
loss of data or profits, resulting from furnishing, performance, or use of this material.
This information is provided “as is” and Posiflex Technology, Inc. expressly disclaims
any warranties, expressed, implied or statutory, including without limitation implied
warranties of merchantability or fitness for particular purpose, good title and against
infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex Technology, Inc. reserves the
right to alter product designs, layouts or drivers without notification. The system
integrator shall provide applicative notices and arrangement for special options utilizing
this product. The user may find the most up to date information of the hardware from:
http://www.posiflex.com or http://www.posiflex.com.tw or http://www.posiflexusa.com
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex Technology, Inc. will not be responsible for any loss of data
resulting from the use, disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Technology, Inc. the publisher of this documentation.
© Copyright Posiflex Technology, Inc. 2011
All brand and product names and trademarks are the property of their respective holders.

DT-308 Series

Desktop Terminal

User’s Manual

Rev. Original

Part 1

ALERT TO OUR HONORABLE CUSTOMERS:

 Please always read thoroughly all the instructions and documents

delivered with the product before you do anything about it. Don’t
take any premature action before you have a full understanding of
the consequences.

 This product contains inside a Lithium battery. Please always

follow local environmental protection laws / regulations for disposal
of used batteries and always replace only with battery of same type.

 If you have an UPS battery installed in the product:

 Temperature above 40°C must be strictly avoided as it

could cause termination of battery life and unexpected result
even if the UPS battery is not in work.

 Do not power off the system just by shutting off the AC

power leaving the battery supporting the whole system till
completely exhausted. Repeatedly using it up or improper
maintenance reduces the battery life dramatically.

 Always fully recharge the battery at least once every 3

months if the battery is not connected.

 Always disconnect the UPS battery from the system if the

system is to be left OFF for more than 72 hours to prevent
possible damage. Only connect the UPS battery back right
before you are going to re-power on the system.

 Replace the UPS battery as soon as the monitoring software

indicates the battery is out of service. Attempt to recharge a
dead battery is dangerous!

DAILY MAINTENANCE GUIDE

For regular cleaning of the DT systems, please use only soft haired
brush or dry soft cloth. You may use moist soft cloth to remove stains when
necessary. Apply only proper amount of mild neutral detergent for obstinate
stains. Please note that never use Acryl dissolving solvent or Polycarbonate
dissolving solvent. You may apply ammonia-based glass cleaner only on the
screen surface.

Risk Of Explosion If Battery Is Replaced By An Incorrect Type

Dispose Of Used Batteries According To Local Regulations

CAUTION

Part 2

INTRODUCTION

PRODUCT PICTURES

Front View Inside Front Door

1

2

3

9

10

11

12

Left Side View Rear Top View II

Rear View Bottom View

4

8

5

7

6

9

10

11

9

10

13

14

15

16

17

Part 3

PARTS IDENTIFICATION

1. Display unit

2. Keyboard area (stroke type in the picture)

3. Front Cover

4. Power indicator

5. USB Port

6. Power Switch

7. Front door latch

8. MSR slot

9. Display unit support steel wire

10. UPS battery cover

11. Cable cover

12. Cable cover compression button

13. Cable exit

14. Jumper setting service window bracket

15. DRAM bay bracket

16. HDD bay bracket

17. Rubber feet

PRODUCT FEATURES

Standard Features:

a)

a)

CPU: Intel Pine View D-SC 1.8GHz, 512K Cache CPU

a)a)
b)

b)

Data storage device: SATA HDD or optional SSD

b)b)
c)

c)

40 key programmable keyboard in keystroke type or flat type

c)c)
d)

d)

Touch open front door protecting power switch and USB port.

d)d)
e)

e)

High quality 8” TFT active matrix LCD panel

e)e)
f)

f)

LCD panel with easy tilt angle adjustment from 15° to 90°

f)f)
g)

g)

VGA memory support DVMT 4.0

g)g)
h)

h)

Durable resistive type touch panel (Option).

h)h)
i)

i)

Touch control functions: left/right button, double click, drag & draw

i)i)

(Option).

j)

j)

Easy maintenance construction

j)j)
k)

k)

Support WinCE / WEPOS / POSReady / Win 7 / Linux

k)k)
l)

l)

Various I/O ports supported, including:

l)l)

1. 4 serial ports in form of DB9 connectors. COM1/2/3/4 ports can
support +5V DC through software switch control & Jumper setting.

2. one cash drawer port.

3. one LAN port 10/100/1000 Mb Ethernet with LAN status indicators
on jack (green for link, orange for data transmission)

4. 4 standard USB ports (3 ports on the I/O plate, 1 port on the front

Part 4

side)

5. one UPS battery connector

6. one DC 12 V power input connector

m)

m)

Support DDR3 SDRAM with maximum memory size 4GB in one SO-

m)m)

DIMM module

n)

n)

Built-in UPS function (with battery option) to support system from

n)n)

intermittent power failure.

o)

o)

Accidental power off protection – power switch resides inside front

o)o)

door and it can be programmed to be an “ON only” switch

Option Items:

Note: The underlined option items in the following list must be set prior to

shipment from the factory. The rest items can be set by the dealers.
a) DDR3 SDRAM memory expansion up to 4GB
b) Integrated rear mount device PD-201 low profile (1 x 16) LCD

customer display or integrated base mount device PD309/U (2 x 20)

LCD pole display and PD-2605/U VFD pole display.
c) Integrated MSR in keyboard area
d) UPS battery
e) Preload OS WinCE / WEPOS / POSReady / Win 7 / Linux
f) Durable resistive type touch panel with Touch control functions:

left/right button, double click, drag & draw.

Part 5