Part 1
FCC Notes:
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.
Warranty Limits:
Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.
About This Manual:
Posiflex Technologies, Inc. has made every effort for the accuracy of the content in this
manual. However, Posiflex Technologies, Inc. will assume no liability for any technical
inaccuracies or editorial or other errors or omissions contained herein, nor for direct,
indirect, incidental, consequential or otherwise damages, including without limitation
loss of data or profits, resulting from furnishing, performance, or use of this material.
This information is provided “as is” and Posiflex Technologies, Inc. expressly
disclaims any warranties, expressed, implied or statutory, including without limitation
implied warranties of merchantability or fitness for particular purpose, good title and
against infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex Technologies, Inc. reserves the
right to alter product designs, layouts or drivers without notification. The system
integrator shall provide applicative notices and arrangement for special options utilizing
this product. The user may find the most up to date information of the hardware from:
http://www.posiflex.com or http://www.posiflex.com.tw or http://www.posiflexusa.com
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex Technologies, Inc. will not be responsible for any loss of data
resulting from the use, disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Technologies, Inc. the publisher of this documentation.
© Copyright Posiflex Technologies, Inc. 2009
All brand and product names and trademarks are the property of their respective holders.
DT-207 / 208 Series
Desktop Terminal
User’s Manual
Rev. A0
P/N:
1
330
090
0020
Part 2
ALERT TO OUR HONORABLE CUSTOMERS:
l Please always read thoroughly all the instructions and documents
delivered with the product before you do anything about it. Don’t
take any premature action before you have a full understanding of
the consequences.
l This product contains inside a Lithium battery. Please always
follow local environmental protection laws / regulations for disposal
of used batteries and always replace only with battery of same type.
l If you have an UPS battery installed in the product:
² Temperature above 40°C must be strictly avoided as it
could cause termination of battery life and unexpected result
even if the UPS battery is not in work.
² Do not power off the system just by shutting off the AC
power leaving the battery supporting the whole system till
completely exhausted. Repeatedly using it up or improper
maintenance reduces the battery life dramatically.
² Always fully recharge the battery at least once every 3
months if the battery is not connected.
² Always disconnect the UPS battery from the system if the
system is to be left OFF for more than 72 hours to prevent
possible damage. Only connect the UPS battery back right
before you are going to re-power on the system.
² Replace the UPS battery as soon as the monitoring software
indicates the battery is out of service. Attempt to recharge a
dead battery is dangerous!
DAILY MAINTENANCE GUIDE
For regular cleaning of the DT systems, please use only soft haired
brush or dry soft cloth. You may use moist soft cloth to remove stains when
necessary. Apply only proper amount of mild neutral detergent for obstinate
stains. Please note that never use Acryl dissolving solvent or Polycarbonate
dissolving solvent. You may apply ammonia-based glass cleaner only on the
screen surface.
CAUTION
Risk Of Explosion If Battery Is Replaced By An Incorrect Type
Dispose Of Used Batteries According To Local Regulations
Part 3
INTRODUCTION
PRODUCT PICTURES
Front View Inside Front Door
Front Top View Rear Top View I
Left Side View Rear Top View II
Rear View Bottom View
21
24 12 20 22 26 27 13 23 25 19 14 11 16 17 17 16 10 18 15 15 1 15 8 12 14 10 13 2 9 11 3 4 1 3 4 5 7 2 6
Part 4
PARTS IDENTIFICATION
1. Display unit (7” LCD panel for DT-207 / 8” LCD + Touch panel
for DT-208)
2. Keyboard area (stroke type in the picture)
3. Front door
4. Power indicator
5. Power switch
6. Front door latch
7. CF memory card reader slot
8. MSR slot
9. Display unit back cover
10. System top cover
11. Display unit support trough
12. Display unit support steel wire
13. Option customer display PD-201
14. Option WLAN antenna
15. Cable cover
16. UPS battery cover
17. Customer display cover
18. Cable cover lock button
19. Keyboard cover
20. Top mount option module cover
21. Display unit support steel wire rest ditch
22. Cable exit
23. Rubber feet
24. Jumper setting service window bracket
25. Jumper setting service window fixing screw
26. DRAM area bracket
27. DRAM area fixing screw
PRODUCT FEATURES
Standard Features:
a) CPU: AMD LX-700
b) Fan free structure with delicately designed internal natural ventilation
c) Data storage device:
CF memory card (default) or optional IDE HDD 40 GB or above
d) 40 key programmable keyboard in keystroke type or flat type
e) Touch open front door protecting power switch and CF card reader slot
f) High quality 7” or 8” TFT active matrix LCD panel
g) LCD panel with easy tilt angle adjustment from 15° to 90°
h) VGA memory size shared from system memory (16 ~ 254 MB)
Part 5
i) Durable resistive type touch panel that endures 35 million touches min.
at same spot for DT-208
j) Touch control functions: left/right button, double click, drag & draw
k) Spill proof water resistant structure allowing easy cleaning
l) Easy maintenance construction
m) Support WinCE, WEPOS and Linux environment
n) Various I/O ports supported, including:
1. 4 serial ports in form of DB9 connectors. All serial ports can
support +5V DC or +12V DC
2. one cash drawer port
3. one LAN port 10/100 base T Ethernet with LAN status indicators on
jack (green for link, orange for data transmission)
4. 3 standard USB ports (USB 2.0)
5. one UPS battery connector
6. one 5.5/2.5 Ø coaxial type DC 12 V power input connector
7. one antenna of optional WLAN module
8. one CF card reader slot in front door
o) Support DDR SDRAM with maximum memory size 1GB in one SO-
DIMM module
p) Integrated structure for various option upgrade kit
q) Built-in UPS function (with battery option) to support system from
intermittent power failure internal speaker with 2 W audio amplifier
r) Accidental power off protection – power switch resides inside front
door and it can be programmed to be an “ON only” switch
s) Preconditioned power up function – by alarm clock
Option Items:
Note: The underlined option items in the following list must be set prior to
shipment from the factory. The rest items can be set by the dealers.
a) DDR SDRAM memory expansion up to 1GB
b) Integrated rear mount device PD-201 low profile (1 x 16) LCD
customer display or integrated base mount device PD309/U (2 x 20)
LCD pole display
c) MSR in keyboard area
d) RFID module in flat type keyboard area
e) UPS battery
f) WLAN module
g) Preload OS
Part 6
INSTALLATION GUIDES
CAUTION: Before any installation or cable connection to the set, please
always make certain that the system is turned off and the
external power source to the set is removed to prevent electric
hazard! Never touch any metal pin in the connectors or
circuits to avoid high voltage hazard or electrostatic discharge
damage unless the operator is well grounded. Failure to do the
above will void the product warranty!
NON-USER-INSTALLABLE OPTIONS
Installation of options such as WLAN (WiFi) / RFID / MSR / HDD
must be done by a qualified technician in the dealer’s site only. This operation
is not open to end user.
OPENING CABLE COVER
The DT-207 / DT-208 series is constructed for very easy maintenance.
Press inward one at a time both plastic buttons
at lower rear corners on both sides of the
system unit (circled in right picture) to release
the lower part of cable cover. Please note that
there are 2 plastic hooks on top edge of cable
cover as rectangular marked in the picture
holding the top cover at arrowed positions.
Push down the hooks to release the cable cover
hook from the system top cover to show the
connection area.
INSTALLING UPS BATTERY (OPTION)
The UPS battery is in the carton at delivery if ordered. Push the 2
UPS battery cover latches on parting line
between the system top cover and the cable
cover to the front as arrowed in the right
picture to remove the UPS battery cover with
the customer display cover installed on it and
to reveal the UPS battery cavity. Pass the UPS
battery cable through a hole in the cavity to enter
the connection area as arrowed in the left picture.
Please note that there is a ribbon in this cavity for
easy battery retrieval. Seat the battery on this
ribbon while the free end of the ribbon comes out
as circled in the left picture.
Loading...