1
DS-200 DS-300
DS-210/220 DS-310/320
Package Contents
(for DS-200/300)
Dock station.................................(x1)
12V/60W power adaptor +
power cord………………………(x1)
Desktop mounting kit pack……..(x1)
(including 2 fixing screws,
2 plastic anchors, and 1 desktop
mounting bracket)
User manual…………………….(x1)
Package Contents
(for DS-210/220/310/320)
Dock station……………………(x1)
12V/100W power adaptor +
power cord……………………...(x1)
Thermal paper roll of 80 mm width
………………………………….(x1)
Spacer plate for thermal paper roll of
58mm width…………………….(x1)
Desktop mounting kit pack……..(x1)
(including 4 fixing screws, 4 plastic
anchors, and 1 desktop mounting
bracket)
User manual…………………….(x1)
DS-200/210/220/300/310/320
Dock Station
User Manual
12530901020 Ver. A0
http://www.posiflex.com
2
Views of the Dock Station
Front View
※ Error LED Indicator, Paper-out LED Indicator, Printer Wi-Fi Indicator,
Feed Button, and Paper Roll Exit are provided for DS-210/220/310/320
only.
Front Inner View
※ All the parts on the front inner side are provided for DS-210/220/310/320
only.
Power LED Indicator
Power Button
Paper Roll Exit
Error LED Indicator
Paper-out LED Indicator
Printer Wi-Fi Indicator
Feed Button
Paper Near End Sensor
Paper Roll Compartment
Wi-Fi Reset Button
Paper Roller
3
Rear View
DS-200/210/220 DS-300/310/320
Top View
DS-200/210/220 DS-300/310/320
Pistol Grip (PG-200/E) Holder
Bottom I/O Cover
Cable Exit
Guiding Wedge
Guiding Wedge
Tablet (MT Series) Docking Connector
Guiding Wedge
4
Bottom View
Right Side View
View of I/O Interface of DS-200/210/220/300/310/320
1
12VDC-IN Power Jack
2
RJ11 Cash Drawer Port
3
RJ45 LAN Port
4
DB-9 COM Port
5
USB 2.0 Port
Paper Roll Cover Release Lever
(For DS-210/220/310/320 Only)
1 2 3
4
5
Rubber Foot
Rubber Foot
5
Loading a Paper Roll (for DS-210/220/310/320 Only)
1. Press down the paper roll cover release lever to
release the paper roll cover.
2. The paper roll cover ejects. Then, open the paper
roll cover manually.
3. Drop the 80mm-wide thermal paper roll inside
the paper roll compartment of the printer, as
shown in the right figure.
4. Drag the paper roll to the portion where the
paper cutter is installed.
5. To avoid the printing problem occurring, push
the central portion of the paper roll cover to
close, and make the tail of the paper roll come
out of the track between the paper roll cover and
the front cover.
Press
Paper Cutter
Push
6
6. Determine that the paper roll is completely
loaded in the paper roll compartment of the
printer and the paper roll is dragged out of the
track between the paper roll cover and the front
cover.
To avoid paper jam occurring, do NOT press the printer’s
release button during printing.
When a paper jam occurs, press the release button to
release the paper cover. Then, remove the jammed paper
and reinstall the paper roll. Next, close the paper cover
properly and firmly.
If the auto cutter is also jammed, the paper cover will be
locked. Should the cutter jam be so serious to interfere the
paper cover release operation, please push the paper cover
and press the release button several times. If the problem
cannot be solved none the less, please call your local
service center for help right away.
Placing the MT Series on the Dock Station
1. Align the two dock station locking holes on the MT series tablet with the
two guiding wedges on the dock station.
Loading...