CASH
DRAWER
n USER’S GUIDE VER. B
NOTICE
The manufacturer of the POS cash drawer makes no representation or warranties, either
expressed or implied, by or with respect to anything in this manual, and shall not be
liable for any implied warranties of fitness for a particular purpose or for any indirect,
special or consequential damages. Information in this document is subject to change
without notice and does not represent a commitment on the part of the manufacturer.
FCC NOTICE
This equipment generates, uses, and can radiate radio frequency energy and if not
installed and used in accordance with the instructions manual, may cause interference to
radio communications. It has been tested and found to comply with the limits for a Class
A digital device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever
measures may be required to correct the interference.
Models CR-3100/3200
CR-3104/3204
INTERFACE DESCRIPTION
. CR3100/3200 is a dumb cash drawer, which must be driven by POS printer or Posiflex
POS system.
. CR3104/3204 is a dedicated low cost RS232 cash drawer, which can be directly driven by
RS232 signal.
FEATURES
. Rugged design with reinforced heavy gauge steel construction
. Large ball bearings riding on special guides for remarkably smooth drawer slide
. Contemporary style
. Advanced electronics that extend the MTBF (Mean Time Between Failure)
. Precision mechanical parts with tight tolerance to assure wobble-free drawer movements
. Check slot for non-cash or large-bill transaction
. Three-position lock for maximum cash security
. Drawer open sensor
. Dedicated RS232 Interface (CR3104/3204 only)
. Removable tray with a lock-on cover. Bill compartments and coin compartments are
adjustable. The tray cover TC3100 for CR3100/3104 and TC3200 for CR3200/3204 are
optional.
SPECIFICATIONS
MECHANICAL: Dimensions: 500 (W) x 420 (D) x 90 (H) mm (CR-3200/3204)
400 (W) x 410 (D) x 85 (H) mm (CR-3100/3104)
Weight: 9.0Kgs (CR-3200/3204) and 6.7Kgs (CR-3100/3104)
ELECTRICAL:
INPUT TO SOLENOID
Pulse Amplitude 12 to 24 VDC Max. Input Voltage 26.4 VDC
Pulse Width 100 to 200 msec Current Consumption 1A @ 12 VDC
Pulse Duty Cycle 10% max. Activation Current 0.9 A max.
SERIAL INPUT (CR3104/3204 only)
Data Format
Protocol No handshake
8P Telephone JACK PIN configuration (CR3100/3200 only)
PIN1 (BLACK) OPEN drawer sensor, connects to PIN2 when drawer open
PIN2 (RED) OPEN drawer sensor, connects to PIN1 when drawer open
PIN7 (GREEN) INPUT to solenoid
PIN8 (YELLOW) INPUT to solenoid
Standard RS232C
Baud rate:150,300,600,1200,2400,4800,9600,19200
Parity: none, even, or odd
Data bits: 7 or 8
INTERFACE DESCRIPTION
Model CR-3100/3200 with POS Printer Interface:
Whenever the POS application software sends the required special command to the
POS printer or CR port of Posiflex POS system, the printer will output an electrical pulse
1
to open the drawer. This required special command is determined by the type of the POS
printer used. For example, the special command for STAR POS printer and Posiflex POS
system CR port is the bell command (07H).
Model CR-3104/3204 with Dedicated Interface:
Whenever the POS application software transmits any kind of data to the computer
COM1 (or COM2) port, the drawer will be opened.
FUNCTIONAL TEST (CR3104/3204 only)
1. Under DOS prompt, type “MODE COM1 (or COM2) 96 N 8 1”. Hit the ENTER key.
2. Type “TYPE CON>COM1 (or COM2)”. Hit the ENTER key.
3. Type “ABC” (or any code). Hit the ENTER key, then the drawer will open.
4. Hit CTRL-C (Press Ctrl and C keys together) to return the computer back to the normal
display mode.
INSTALLATION
CR3100/3200: Connect the drawer to POS printer as shown in Fig1.
CR3104/3204: 1.Open the PC case. Put the metal bracket with power connector into one
of the I/O windows.
2. Connect the cable to the HDD type power connector of PC power
supply. See Fig2. Then close the PC case.
3. Connect the DB-9 connector to the computer's serial port of COM1 (or
COM2). Connect the 4P phone plug connector to the added I/O bracket.
See Fig3.
CARTON CONTENTS
1. Cash drawer preassembled
2. User’s manual
3. Key 2pcs: There is a key serial No. sticker on the cash drawer bottom plate. If user lost
the key, he/she can order the key according to this number.
4. Signal cable: the standard signal cable for CR3100/CR3200 is CCBLA-180 which has a
8 pin plug at one end to connect to the cash drawer and a 6 pin plug at the other end to
connect to the POS printer. This cable serves for most popularly used POS equipment
such as all Posiflex POS terminals, all Posiflex POS printers, most EPSON POS
printers, most STAR POS printers and all other compatibles. The user may cut the 6 pin
end or order the ready cut cable CCBLA-180A and assemble this free end according to
his POS printer specification if the POS printer used applies different connection. The
cable connection on CCBLA-180A is as below:
Wire color RJ45 Function
Red Pin 1 Drawer open sense
Blue Pin 2 Drawer open sense return
Green Pin 7 + 24V to solenoid
Yellow Pin 8 Drawer kick pulse
As for CR3104/CR3204, the serial signal cable is already built on.
5. Power connector cable and I/O bracket plate. (for CR3104/CR3204 only)
2
or POS Printer
8P Telephone Jack
Posiflex POS system
8P Telephone Plug
6P Telephone Plug
Fig 1
Fig 2
Fig 3
3
Loading...