CR-2000 SERIES
CASH DRAWER
FCC Notes:
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.
Warranty Limits:
Warranty terminates automatically when any person other than the authorized
technicians opens the machine. The user should consult his/her dealer for the problem
happened. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.
About This Manual:
Posiflex has made every effort for the accuracy of the content in this manual. However,
Posiflex will assume no liability for any technical inaccuracies or editorial or other
errors or omissions contained herein, nor for direct, indirect, incidental, consequential
or otherwise damages, including without limitation loss of data or profits, resulting
from the furnishing, performance, or use of this material.
This information is provided “as is” and Posiflex Inc. expressly disclaims any
warranties, expressed, implied or statutory, including without limitation implied
warranties of merchantability or fitness for particular purpose, good title and against
infringement.
The information in this manual contains only essential hardware concerns for general
user and is subject to change without notice. Posiflex reserves the right to alter product
designs, layouts or drivers without notification. The system integrator shall provide
applicative notices and arrangement for special options utilizing this product. The user
may find the most up to date information of the hardware from web sites:
http://www.posiflex.com
All data should be backed-up prior to the installation of any drive unit or storage
peripheral. Posiflex will not be responsible for any loss of data resulting from the use,
disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, or otherwise, without prior express written consent from
Posiflex Inc. the publisher of this documentation.
© Copyright Posiflex Inc. 2006
All brand and product names and trademarks are the property of their respective holders.
USER’S MANUAL
Rev. Original
or http://www.posiflex.com.tw
P/N: 19230900010
Part 1
BRIEF INTRODUCTION
INTRODUCTION
This specification defines the CR2000 series of Posiflex products.
This product series is a flip-top type cash drawer. This series provides
Aluminum alloy die cast base and wearproof stainless steel top surface
with zero externally accessible screw.
FEATURES
Flip-top design
Rugged design with no screw to be accessed from outside
Contemporary style
Advanced electronics that extends the MTBF (Mean Time Between
Failure)
Three-position lock for maximum cash security
Check slot for non-cash or large-bill transaction without opening
drawer
6 fixed bill compartments
8 coin compartments. Partially adjustable in size and number by use of
coin compartment separator
Provided with various interface selection including direct (printer) drive,
dedicated RS232, USB
Optional additional removable tray. Also optional tray cover with lock
WEPOS certified
2 color choices: Ivory and Black
MODEL NUMBER & INFERFACE
Model Number Interface Security Code Power / Source
CR-2000 Printer drive N. A.
CR-2004 Dedicated RS232 serial N. A. 12VAC / Adaptor
CR-2005 USB USB PID 12VAC / Adaptor
12/24 V Pulse /
Printer
CARTON CONTENTS
1. Cash drawer pre-assembled.
2. User’s manual.
3. Separators of coin compartment: 5 pcs.
4. Key 2pcs: There is a key serial No. sticker on the cash drawer bottom
plate. If user lost the key he/she can order the key according to this
number.
Part 2
5. Signal Cable depend on model
a). For CR-2000: The standa rd signal cable is 21863018010 which has a 8
pin plug at one end to connect to the cash drawer and a 6 pin plug at the
other end to connect to the POS system/printer. This cable serves for
most popularly used POS equipment such as all Posiflex POS terminals,
all Posiflex POS printers, most Epson POS printers, most Star POS
printers and all other compatibles. The user may cut the 6 pin end and
assemble this free end according to his POS printer specification if the
POS printer used utilizes different connection. The cable co nnection on
the wires is as below:
Wire color
RJ45 Function
Red Pin 1 Drawer open sense
Blue Pin 2 Drawer open sense return
Green Pin 7 + 24V to solenoid
Yellow Pin 8 Drawer kick pulse
b). For CR-2004: Serial signal cable (RS232 conversion cable
21863259900/21863159900).
c). For CR-2005: USB cable (USB Cable 21863250800/21863150800)
6. Power Source depend on model
a). For CR-2000: not applicable
b). For CR-2004: Power adapter 12VAC 1.5A
c). For CR-2005: Power adapter 12VAC 1.5A
INSTALLATION
Coin compartment adjust:
The coin compartment separator can be removed from and inserted
till click into the grooves in adjustable coin compartment zones for appropriate
compartment size.
Coin Compartment Separator
Adjustable Coin Compartment
Part 3
CR-2000:
1). Connect the 8 pin plug of CR cable to cash drawer and the 6 pin plug to
CR port of POS system or POS printer as shown below:
Rear View
8P Telephone Jack
Output to drawer
Cash Drawer
With Printer Interface
CR Cable: 21863018010
Connect to POS System or
Printer 6P Telephone Jack
2). Turn the keylock to standby position.
CR-2004:
1). Connect the 4 pin RJ11 plug of RS232 conversion cable to the RJ 11
jack at the rear side of CR-2004 and connect the DB 9 pin connector
to RS232 port of host (PC or POS) system as shown in drawing below.
2). Check the specification of power adaptor on its nameplate. Insert the
power adaptor into the correct power outlet. Insert the output plug to
the power jack at rear side of CR-2004 to supply power for drawer
kickout.
3). Turn the keylock to standby position.
4). Set the communication protocol of the RS232 port in host system to
use baud rate of either 9600 bps or 19200 bps.
Rear View
USB Type B Connector
RJ11(4P4C) Telephone Jack
AC 12V I/P
USB Cable:
(21863150800/21863250800)
Connect to USB Port of host
system (For CR-2005 only)
Cash Drawer With RS232 & USB Interface
Connect to Adaptor
RS232 Conversion Cable:
(21863159900/21863259900)
Connect to RS232 port of host system
(For CR-2004 only)
Part 4
CR-2005:
1). The drawer number (PID) is default to be 7. Refer to the guidance fo r
“Jumper Setting Change” below if the PID has to be changed.
2). Connect USB type B connector (more or less square one) of USB
cable to the USB connector at rear side of CR-2005 and the type A
connector end to USB port of host (PC or POS) system as shown in
drawing above.
3). Check the specification of power adaptor on its nameplate. Insert the
power adaptor into the correct power outlet. Insert the output plug to
the power jack at rear side of CR-2005 to supply power for drawer
kickout.
4). Turn the keylock to standby position.
5). Install the USB utility driver from Posiflex Product Information CD
with Posiflex POS system or visit our web sites
http://www.posiflex.com
http://www.posiflexusa.com
or http://www.posiflex.com.tw or
for latest updates.
Jumper Setting Change:
1). Use key to open the cash drawer. Take out the removable tray and you
can find a control board in the bottom. The lay out of the control
board is illustrated below.
JP1
21
2). USB PID select: jumpers over pins 3-4, 5-6 or 7-8 define a drawer
number for the cash drawer as in below table so that this cash drawer
is going to respond accordingly in USB communication. Please note
that within each system there should never be any 2 USB interface
cash drawers car rying the same drawer number.
USB PID
JP1 pins
0 1 2 3 4 5 6 7
3-4 Short Short Short Short Open Open Open Open
5-6 Short Short Open Open Short Short Open Open
7-8 Short Open Short Open Short Open Short Open
Part 5
UPOS and WEPOS driver application:
Please first find in Posiflex Product Information CDROM or
download from Posiflex web sites for UPOS driver setup. In this application
CR-2004 responds to OpenDrawer command only; CR-2000/2004 are
compliant to UPOS version 1.7 and CR-2005 is compliant to UPOS version
1.8 and is also WEPOS certified.
SPECIFICATIONS
MECHANICAL: Dimensions:
481.5 (W) x 174.9 (D) x 101.5 (H) mm
19.0” (W) x 6.9” (D) x 4.0” (H)
Weight: t.b.f. Kg
Removable tray with a lock-on cover (option)
ELECTRICAL:
Power Source
Solenoid Drive (for CR-2000)
Pulse Amplitude 12 to 24 VDC
Pulse Width 100 to 250 msec
Pulse Duty Cycle 10% max.
Max. Current Consumption 0.75A @ 12 VDC / 1A @ 24 VDC
AC Adaptor (for CR-2004/2005)
Input Voltage 120 VAC ± 10 % / 240 VAC ± 10 %
@50 -60 Hz
Output Voltage 12 VAC at 1.5 A
Interface
Direct Drive: CR-2000
Serial (RS232C)
CR-2004
Baud rate 9600; 19200
Parity none
Data Bits 8
Stop Bits 1
USB (1.1): CR-2005
Security Code
CR-2005 USB PID
Drawer Open Sense
CR-2000 Drawer open sense circuit shorts when drawer open
Part 6
CR-2004 Pin 9 in DB9 connector goes high when drawer open
CR-2005 Through USB driver
KEYLOCK OPERATION
Keylock
STRUCTURE
Inside CR-2000/ 2004/ 2005
Lock ( ): Physically lock the drawer.
Open ( ): Open the drawer by the key.
Standby ( ): Automatically open the drawer by POS
printer or POS system or interface
signal control
Check Slot
Bill compartment
Adjustable coin
compartment
Cash Tray
Fixed coin compartment
Check Storage
Part 7
Part 8
Part 9
在居住的環
可能會造成射頻干
使用者會被要
警告使用者
這是甲類的資訊產品，
境中使用時，
擾，在這種情況下，
求採取某些適當的對策。
Part 10
Loading...