1
CD-3600U/3601U
2D image scanner
USB cable
Quick setup guide
CD-3600R/3601R
2D image scanner
RS-232 cable
Quick setup guide
CD-3600-SK/CD-3601-SK
2D image scanner
USB cable for SK-300
Quick setup guide
Firmware Version
CD-3600/3601 (U/R)
2D Image Scanner
Quick Setup Guide
18090900050 Ver. D0
http://www.posiflex.com
Trigger Button1
Scan Window
w/ Object Detector
Mounting Screw Hole
Beeper Hole
Interface Cable Connector
Package Contents
Parts of the 2D Image Scanner
Note:
1. The CD-3600/3601(U/R) 2D image scanner can work in Auto Trigger mode or Manual Trigger
mode. The trigger button is provided for the scanner working in the Manual Trigger mode. The
default scan mode of the scanner is Auto Trigger mode.
2
Problem
Diagnostic Tips
The scanner is on but cannot read
any barcode.
The scanner window is dirty. Clean the scanner
window as described in the Scanner Maintenance
section.
The presented barcode type is not enabled. Use this
guide to tell the scanner to accept that type of
barcode.
The host terminal has disabled the scanner. Check
the setup of host terminal.
The barcode type presented is not supported by the
scanner.
The scanner does not accept more
than two or three barcode labels.
Determine whether the required barcode types are
enabled or not.
A stray barcode is sitting somewhere in the scanner
field of view. Remove all barcode labels from the
scanner’s scan volume and try again.
The scanner cannot send the data to the POS
system. Make sure that the scanner is installed well
and your host POS system is ready to receive data.
Scanner Maintenance
The scanner is designed for long-term trouble-free operation and rarely
requires any maintenance. Only an occasional cleaning of the scanner window
is necessary in order to remove dirt and fingerprints.
Wipe the scan window with a soft lint-free cloth and a non-abrasive cleaner to
avoid the scan window from being scratched and damaged. The scan window
can be cleaned while the scanner is running.
The standard interface cable is attached to the scanner with a 10-pin modular
connector. When the connector is properly seated, it is secured in the scanner
by a flexible retention tab. The cable is designed to be field replaceable.
Replacement cables can be obtained from your authorized distributor. To
replace the cable, take the following steps.
1. Make sure the power of both the host terminal and the scanner is powered
off.
2. Disconnect the old scanner cable from the host terminal.
3. Press down the retention tab, and gently pull out the cable.
4. Insert the new interface cable into the bottom of the scanner until it clicks.
Plug the new cable into the host.
Trouble Shooting
This section contains information about how to solve problems that you may
encounter when operating the scanner. If a trouble occurs, please refer to the
following diagnostic tips as a mean to solve the trouble. However, before
referring to the tips, make sure that the scanner is installed well. If the problem
remains, contact your dealer.
3
Problem
Diagnostic Tips
A barcode is read by the scanner but
not accepted by the POS system.
The communication settings of the system port and
the scanner do not match. Adjust the settings to
make them match to each other.
The scanner is not installed well. Contact your
dealer for the proper installation. The software
running on the POS system does not support the
data format of the barcode label.
When a barcode stays close to the
scanner, the barcode cannot be read
automatically by the scanner.
Check whether or not you have enabled the Manual
Trigger mode. If you have enabled this mode
accidentally, please disable the Manual Trigger
mode by scanning the “Disable trigger” barcode in
the advanced user manual.
RS232
USB-HID
USB-VCP
Programming Codes
All barcode names in bold black represent as default settings.
Please cover the unwanted codes for scanning the specific barcode required for
the programming to prevent confusion in code scanning.
Use the user manual downloaded from our global website or taken from the
Information DVD for advanced programming.
User Interface Switch Barcodes with Defaults Setting
※ Before scanning a user interface switch barcode, do NOT do other settings,
otherwise all the settings you have done will go invalid. After a user interface
switch barcode is scanned, if the failure of switch occurs, please re-plug the I/O
cable or re-start your host terminal, and scan the barcode again.
4
RS232
USB-HID
USB-VCP
Defaults Barcode Setting
※ The setting barcodes are not used for user interface switch but only for
customer defaults setting.
5
Disable buzzer
Enable buzzer
Buzzer loudness: Loud
Buzzer loudness: Normal
Buzzer Settings
Trigger Mode
Auto Trigger
The Auto Trigger option is a function that automatically detects a scanned
target and starts reading. There are three methods for detecting a target
code.
1. Green aiming detection
When a target code falls within the aiming range while the green aiming
light is emitted, the target is detected. It is recommended to use this mode
indoors because the detectability is reduced in an environment of higher
illuminance levels than indoors.
Loading...