Posey Mobile Chair Belt Sensor User Manual



FALL MANAGEMENT

Posey® Self-Releasing Chair Belt Sensors

Before using this sensor, read this entire
instruction sheet and save for future reference.

Posey® Self-Releasing Chair Belt Sensors are designed to provide the
earliest possible warning that a patient is at immediate risk of falling.
Monitoring starts as soon the belt is fastened; the alarm activates the
instant the belt is unfastened, before the patient can exit the chair.
Belts adjust from 21” to 44” (53 cm to 112 cm). Hook-and-Loop Belt,
Long, adjusts up to 115” (292 cm). People who may benefit from the
use of this device include restless patients who are at risk of falls and:

• Need a gentle reminder to call for help before getting up; or

• Need an aid to hold hips in place and reduce the risk of forward
sliding.

Chair Belt Sensors are a non-invasive way to monitor patient
movement. However, these devices DO NOT prevent falls and are not
a substitute for good nursing care and regular visual monitoring.

REF

8358 EZ-Clean Alarm Belt

REF

8360 Self-Releasing Chair Belt Sensor Only, Screw-Mounted

REF

8371 Self-Releasing Mobile Chair Belt Sensor Only

REF

8372 Hook-and-Loop Alarm Belt

REF

8372L Hook-and-Loop Alarm Belt, Long

REF

8340 KeepSafe Screw-Mounted Chair Belt System

REF

8370 KeepSafe Mobile Chair Belt System

REF

8280B Sitter II Screw-Mounted Chair Belt System

REF

8280S Sitter II Mobile Chair Belt System

REF

8350 KeepSafe Alarm Unit Only

REF

8281 Sitter II Alarm Unit Only

8340

Mounting Screws

• This device may not be suitable for all high fall-risk patients.
See Posey catalog for other options for such patients.

• Posey Chair Belt Sensors are designed for use with Posey Fall
Alarms ONLY. NEVER connect a Posey Sensor to other
manufacturers’ alarm units.

• Read this entire instruction sheet and save for future reference.
Before use, read and follow all instructions for your Posey
alarm.

Application Instructions:

Screw-Mounted Chair Belt

1. Remove one chair seat screw on each side, closest to chair back

(fig. 1). NOTE: For a large or obese patient, use the second screw

from the back for added strap length.

2. Position buckle ends for proper closure (fig. 1).

3. Insert screw through belt grommet hole on each side; secure

screws to wheelchair seat and frame.

4. Position patient on chair seat, with buttocks against the chair back.

5. Bring straps over patient’s hips and insert male end into buckle

until it clicks shut. Pull firmly on straps to make sure buckle is
locked. To unfasten, press orange button and remove male end.

6. Adjust belt by pulling on loose strap.

Mobile Chair Belt and Hook and Loop Belt

Position straps for proper closure and place them on wheelchair seat (fig. 2). Attach sensor belt to chair.

Mobile Chair Belt - 8370

Fig. 1

Hook and Loop

Alarm Belt

Fig. 2

Posey Company • 5635 Peck Road, Arcadia, CA 91006-0020 USA • www.posey.com
Phone: [phone] or 1.626.443.3143 • Fax: [phone] or 1.626.443.5014

© 2010 Posey Company. All rights reserved.

M1412 REV B 010510

Posey® Self-Releasing Chair Belt Sensors (Cont.)

For Model 8358, 8371 and 8372:

1. Draw strap ends down under chair seat at
a 45˚ angle (fig. 3).

2. Choose a site to attach straps at a juncture
of the frame behind and under the seat,
out of the patient’s reach. Make sure straps
cannot slide in any direction, or change
angle or position (fig. 4).

3. Wrap each strap around its attachment point. Thread tail of each
strap through both metal rings, then back over one ring and through
the other metal ring. Pull straps until secure.

4. Position patient as far back on seat as possible, with buttocks
against the back of the chair.

5. Draw straps across patient’s hips at a 45° angle and fasten belt.

Mobile Chair Belt and EZ Clean Alarm Belt.

• Insert male end into buckle until it clicks shut. Pull firmly on
straps to make sure buckle is locked.

• Adjust belt by pulling on loose strap.

• To unfasten, press orange button and remove male end.

Hook and Loop Belt.
Mate hook and loop straps for snug fit. Pull YELLOW strap to

unfasten.

For Model 8372L (Hook and Loop Sensor Belt, Long)

1. Draw straps down over patient’s lap at a
45˚ angle (fig. 5).

2. Position strap ends behind chair back as
low as possible. Thread tail of one strap
through both metal rings of other strap
(fig. 6), then back over one ring and
through the other metal ring (fig. 7).

3. Pull straps until secure (fig. 8).

4. Mate hook and loop straps for snug fit.

Pull YELLOW strap to unfasten.

Adjust Straps:

ALWAYS adjust straps so belt is snug, but
does not interfere with breathing. You should
be able to slide your open hand (flat)
between the belt and the patient.

If Hook and Loop straps
become wet, alarm may not sound. Excess
moisture may prevent sensor from activating,
increasing risk of injury. If straps become
wet, discontinue use until completely dry.

Fig. 6

Fig. 7

Fig. 8

Fig. 3

45˚

Fig. 5

45˚

8372L

Fig. 4

Mobile Chair Belt/Hook and Loop Alarm Belt/EZ Clean

Alarm Belt rear attachment

To reduce the risk of severe injury or death:

• Check that alarm is ON and working properly EACH TIME
before leaving patient unattended. Press self-release button to
unfasten buckle, or separate hook and loop straps. Alarm
should activate each time you do this. STOP USE AT ONCE if
alarm fails any test.

• DO NOT leave patient unattended unless you are sure patient
understands purpose for and how to remove the belt. Check
that belt is snug, but does not interfere with breathing.

• NEVER jerk or pull on sensor cord to remove plug from alarm.
Doing so will damage the cord or plug and may cause sensor to
fail. ALWAYS use plastic tab to release plug.

Cleaning:

1. Wipe clean with a cloth dampened with disinfectant. Take extra
care with sensor plug.

2. Dry hook and loop straps completely before use. Use a stiff brush
to remove dust and lint from hook and loop.

3. NEVER:

• Use any cleaner that contains Phenol or Benzyl;

• Immerse in liquid; or

• Sterilize with heat.

4. Dry with a clean cloth.

Storage and Handling:

This device is designed for use in normal indoor environments, This
device may be stored in ambient warehouse temperatures at normal
humidity levels. Avoid excess moisture or high humidity that may
damage product materials.

Disposal:

Properly dispose of the product per facility policy

for BIOHAZARDOUS material.

Limited Warranty:

This product is warranted for 1 year from date of first use. See Posey
Catalog for details.

Posey Company • 5635 Peck Road, Arcadia, CA 91006-0020 USA Phone: [phone] or 1.626.443.3143 • Fax: [phone] or 1.626.443.5014 • Web: www.posey.com