Porter-Cable 750 User Manual [en, es, fr]

Instruction

manual

ESPAÑOL: PÁGINA 17

FRANÇAIS : PAGE 31

Double Insulated TIGERCLAW™ Variable Angle RECIPROCATING SAW

MODEL 750 with

Keyless Quik-Change™

Blade Clamp,

Keyless Quik-Change™

Guide Shoe

To learn more about Porter-Cable

visit our website at:

http://www.porter-cable.com

IMPORTANT!

Please make certain that the person who is to use this equipment carefully reads and understands these instructions before starting operations.

The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference.

Model No. __________________________________

Type _______________________________________

Serial No. __________________________________

Part No. A17589 - 03-31-06 - Rev A

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY GUIDELINES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

ADDITIONAL SPECIFIC SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

CARTON CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

ESPAÑOL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

FRANÇAIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

IMPORTANT SAFETY INSTRUCTIONS

using any tool or equipment. Always follow basic safety precautions to reduce the risk of personal injury. Improper operation, maintenance, or modification of tools or equipment could result in serious injury and property damage. These tools and equipment are designed for certain applications. DO NOT modify this product and/or use it for any application other than for which it was designed.

If you have any questions relative to its application, DO NOT use the product until you have written Porter-Cable and we have advised you.

INFORMATION REGARDING SAFE AND PROPER OPERATION IS AVAILABLE FROM:

Read and understand all warnings and operating instructions before

Online, contact us at: www.porter-cable.com

By mail, contact us at:

The Power Tool Institute

1300 Sumner Avenue, Cleveland, OH 44115-2851

www.powertoolinstitute.org

National Safety Council

1121 Spring Lake Drive

Itasca, IL 60143-3201

American National Standards Institute

25 West 43rd Street, 4 floor

New York, NY 10036 www.ansi.org

ANSI 01.1Safety Requirements for Woodworking Machines

The U.S. Department of Labor regulations

Technical Service Manager Porter-Cable 4825 Highway 45 North Jackson, TN 38305

www.osha.gov

SAVE THESE INSTRUCTIONS!

It is important for you to read and understand this manual. The

SAFETY GUIDELINES - DEFINITIONS

information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you

recognize this information.

indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

indicates a potentially hazardous situation which, if not avoided,could result in death or serious injury.

indicates a potentially haz ard ous situation which, if not avoided,may result in minor or mod er ate injury.

used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in property damage.

CALIFORNIA PROPOSITION 65

Some dust created by power sanding, sawing, grinding, drilling,

and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

● lead from lead-based paints

● crystalline silica from bricks and cement and other masonry products

● arsenic and chromium from chemically-treated lumber

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, al ways wear NIOSH/OSHA approved, properly fit ting face mask or res pi ra tor when us ing such tools.

GENERAL SAFETY RULES

instructions listed below may result in electric shock, fire and/ or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Read all instructions. Failure to follow all

To reduce the risk of injury, user must read instruction manual.

SAVE THESE INSTRUCTIONS

1) Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas invite

accidents.

b) Do not operate power tools in explosive atmospheres, such as in

the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety a) Power tool plugs must match the outlet. Never modify the plug in

any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

b) Avoid body contact with earthed or grounded surfaces such as

pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk

of electric shock.

e) When operating a power tool outdoors, use an extension cord

suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

3) Personal safety a) Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of

inattention while operating power tools may result in serious personal injury.

b) Use safety equipment. Always wear eye protection. Safety equipment

such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c) Avoid accidental starting. Ensure the switch is in the off-position

before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool

on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

GENERAL SAFETY RULES

e) Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Keep your

hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly used.

Use of these devices can reduce dust-related hazards.

4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the

rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off.

Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source before making any

adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow

persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power

tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools

with sharp cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance

with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

5) Service a) Have your power tool serviced by a qualified repair person using

only identical replacement parts. This will ensure that the safety of the

power tool is maintained.

continued

ADDITIONAL SPECIFIC SAFETY RULES

1. Hold power tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the

tool"live" and shock the operator.

2. Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is

unstable and may lead to loss of control.

3. Keep blades sharp. Sharp blades will do the job better and safer.

4. Keep hands away from cutting area. When sawing never reach

underneath or behind the material being cut for any reason.

5. When you have finished a cut be careful not to come into contact with the blade. Turn off the motor immediately.

TO BE CERTAIN THAT THERE ARE NO FOREIGN OBJECTS SUCH AS ELECTRICAL WIRE, CONDUIT, PLUMBING PIPES, ETC., THAT MAY COME INTO CONTACT WITH THE BLADE.

7. Never hold work in your hand, lap, or against other parts of your body

when sawing.

8. Wear eye and hearing protection. Always use safety glasses. Everyday

eyeglasses are NOT safety glasses. USE CERTIFIED SAFETY EQUIPMENT. Eye protection equipment should comply with ANSI Z87.1 standards. Hearing equipment should comply with ANSI S3.19 standards.

other airborne particles, including wood dust, crystalline silica dust and asbestos dust. Direct particles away from face and body. Always

operate tool in well ventilated area and provide for proper dust removal. Use dust collection system wherever possible. Exposure to the dust may cause serious and permanent respiratory or other injury, including silicosis (a serious lung disease), cancer, and death. Avoid breathing the dust, and avoid prolonged contact with dust. Allowing dust to get into your mouth or eyes, or lay on your skin may promote absorption of harmful material. Always use properly fitting NIOSH/OSHA approved respiratory protection appropriate for the dust exposure, and wash exposed areas with soap and water.

EXERCISE EXTREME CAUTION WHEN BLIND CUTTING

Use of this tool can generate and disburse dust or

SAVE THESE INSTRUCTIONS!

SYMBOL DEFINITION

V ........................................ volts

A ........................................ amperes

Hz ...................................... hertz

W ....................................... watts

kW ..................................... kilowatts

F ........................................ farads

µF ...................................... microfarads

l .......................................... litres

g ........................................ grams

kg ....................................... kilograms

bar ..................................... bars

Pa ...................................... pascals

h......................................... hours

min ..................................... minutes

s ......................................... seconds

0 .......................................

.../min or …min

..............

or d.c. ................... direct current

or a.c. ....................... alternating current

............................ two-phase alternating current

2N 3

........................... two-phase alternating current with neutral

.............................. three-phase alternating current

3N ............................ three-phase alternating current with neutral

.............................. rated current of the appropriate fuse-link in amperes

................................. time-lag miniature fuse-link where X is the symbol for

.................................... protective earth

no-load speed Revolutions or reciprocations per minute

the time/current characteristic, as given in IEC 60127

.................................... class II tool

IPXX ................................... IP symbol

SAVE THESE INSTRUCTIONS!

MOTOR

Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus or minus 5 percent of that shown on the specification plate on the tool. Several models, however, are designed for A.C. current only. Refer to the specification plate on your tool for proper voltage and current rating.

Do not operate your tool on a current on which the voltage is not within correct limits. Do not operate tools rated A.C.

only on D.C. current. To do so may seriously damage the tool.

EXTENSION CORD SELECTION

If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts (10 volts for 230 volts) at 150% of rated amperes.

If an extension cord is to be used outdoors, it must be marked with the suffix W-A or W following the cord type designation. For example – SJTW-A to indicate it is acceptable for outdoor use.

RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS

Length of Cord in Feet

115V 25 Ft. 50 Ft. 100 Ft. 150 Ft. 200 Ft. 250 Ft. 300 Ft. 400 Ft. 500 Ft. 230V 50 Ft. 100 Ft. 200 Ft. 300 Ft. 400 Ft. 500 Ft. 600 Ft. 800 Ft. 1000 Ft.

0-2 18 18 18 16 16 14 14 12 12 2-3 18 18 16 14 14 12 12 10 10 3-4 18 18 16 14 12 12 10 10 8 4-5 18 18 14 12 12 10 10 8 8 5-6 18 16 14 12 10 10 8 8 6 6-8 18 16 12 10 10 8 6 6 6

8-10 18 14 12 10 8 8 6 6 4 10-12 16 14 10 8 8 6 6 4 4 12-14 16 12 10 8 6 6 6 4 2 14-16 16 12 10 8 6 6 4 4 2

Nameplate Ampere Rating

16-18 14 12 8 8 6 4 4 2 2 18-20 14 12 8 6 6 4 4 2 2

SAVE THESE INSTRUCTIONS!

CARTON CONTENTS

The Tiger Saw comes with a case and blades.

FUNCTIONAL DESCRIPTION

The Porter-Cable variable angle reciprocating saw is designed for cutting wood up to 12" thick, metal up to 3/4" thick and various other materials (plastics, fiberglass and hard rubber).

ASSEMBLY

NOTE: This tool is shipped completely assembled. No assembly time or tools are

required.

OPERATION

SELECTING THE BLADE

For best performance, longer blade life, and smoother cut, select the proper blade for the job. Always select a blade for metal cutting that will engage at least three teeth in the thickness of the workpiece.

INSTALLING THE BLADE with Keyless Quik-Change™ Blade Clamp

1. Fully extend the reciprocating shaft to permit access to the keyless Quik-Change™ blade release collar (A) Fig. 1. If necessary, connect the tool to the power source and gently squeeze the trigger switch to move the reciprocating shaft to its outermost position (in Fig. 1).

Disconnect the tool from the power source!

2. Pivot the guide shoe (B) Fig. 1 forward to improve access to the blade clamp.

3. To open the blade clamp, rotate (counterclockwise) and hold the blade release collar (A) Fig. 2 (as viewed from the front of the saw).

Fig. 1

NOTE: You can temporarily remove the keyless Quik-Change™ pivoting guide shoe

to make blade installation easier. Release the locking lever (B) Fig. 3 to remove (see “Pivoting Guide Shoe Adjustment with keyless Quik-Change™” section of this manual).

Do not operate this tool with the guide shoe removed.

4. Insert the blade into the clamp until it bottoms. Allow the release collar (A) Fig. 4

to rotate clockwise to lock the blade in place.

NOTE: You can install the blade upside down if you prefer for better reach in tight fitting applications.

5. To remove the blade, repeat steps 1 through 3. Pull the blade from the blade clamp while you hold the release collar in the open position.

Fig. 2

Fig. 3

Fig. 4

NOTE: When you remove a blade, if the blade clamp collar resists rotation, work the

blade up and down while rotating the clamp (in a counter-clockwise direction).

If the blade breaks, leaving nothing to grasp (to pull it from the clamp), use another blade as a tool to remove the broken piece (Fig. 5). While holding the release collar in the open position, use the

FLUSH RECESSED BREAK BREAK

BROKEN BLADE

tip of another blade to “hook” the broken piece and pull it from the clamp. (A thin, fine-toothed, metal-cutting blade works best.)

Periodically clean the blade clamp with dry compressed air. DO NOT lubricate the blade clamp. Lubricant can attract

Fig. 5

contamination.

Wear ANSI Z87.1 safety glasses while using compressed air.

INSTALLING THE OPTIONAL BLADE ADAPTER

Disconnect tool from power source!

You can use standard jig saw blades in this tool with the proper blade adapter (sold

separately). To prepare to install a standard jig saw blade, follow steps 1 through 3 in "INSTALLING THE BLADE" section of this manual.

1. Insert the jig saw blade adapter (A) Fig. 6 into the the clamp until it bottoms. Insert the jig saw blade (B) into the blade adapter (A). Rotate the release collar clockwise to lock the blade in place (Fig. 4).

2. To remove the jig saw blade and blade adapter, reverse the above procedure.

Fig. 6

ROTATABLE GEAR HOUSING ADJUSTMENT

1. The variable angle reciprocating saw is designed with a rotatable gear housing for easy adjustment of cutting angles. This feature permits access to places where conventional tools cannot be used.

2. The gear housing can rotate 90° up or 90° down. You can adjust the angle to 13 detente positions (6 up, 6 down, 1 straight). This feature is designed to simplify adjusting the up or down angle of cut and provides accessibility in close quarters.

Disconnect the tool from the power source!

3. To rotate the gear housing, depress and hold the lock button (A) Fig. 7. Move the gear housing up or down to the desired position or angle. Release the lock button and continue to move the gear housing until the lock button snaps into the desired detente position (Fig. 8).

Fig. 7

Fig. 8

FRONT SCROLL HOUSING ADJUSTMENT

Disconnect the tool from the power source!

The variable angle reciprocating saw has a rotatable front scroll housing for easier radius cuts. This feature permits additional access in close workspaces where conventional tools cannot be used. The front scroll housing can rotate 360°, and can be adjusted radially to 12 detente positions. This feature is designed to simplify adjusting to radial angle of cut. Combined with the rotatable gear housing, this housing provides accessibility to almost any cutting operation.

To rotate the front scroll housing, depress and hold the lock button (A) Fig. 9. Hold the button depressed while moving the front scroll housing clockwise or counterclockwise to the desired radial position or angle. Then release the lock button and continue to move the front scroll housing until the lock button snaps into the desired detente position (B) Fig. 10.

Fig. 9

Fig. 10

PIVOTING GUIDE SHOE ADJUSTMENT with keyless Quik-Change™

Disconnect the tool from the power source! Do not operate this tool with the guide shoe removed.

The Model 750 is supplied with a keyless Quik-Change™ guide shoe. The pivoting guide shoe (A) Fig. 11 serves as a rest while making a cut and can be adjusted to accommodate many types of cutting applications.

To adjust, rotate the lever (A) Fig. 12. releasing the pivoting guide shoe (B). Adjust to the desired position and close the lever (A) Fig. 13. The keyless QuikChange™ pivoting guide shoe is designed with a raised lip (C) Fig. 12 at the end that prevents the guide shoe from locking in position if it is extended out too far. After adjusting, make sure the locking lever is completely closed in the locked position (A) Fig. 12.

NOTE: DO NOT force the locking lever closed. Adjust the shoe to allow the lever to lock in position without force.

Fig. 11

Fig. 12

Fig. 13

HOW TO HOLD THE SAW

The metal parts of the saw, blade and pivoting guide shoe may be made live if the blade cuts into live wiring within a wall.

14 or Fig.15. Make sure that the the rubber front housing cover is properly installed and NOT DAMAGED. The rubber front housing cover also serves as an assembly pin retention mechanism. If the cover is removed or becomes damaged, the pins can fall out.

To prevent accidental electrical shock, hold the tool as shown in Fig.

Fig. 14 Fig. 15

your hands. Use both hands to hold and control the tool, especially when making angle or scroll cuts. Exercise caution when cutting toward yourself.

Always exercise extreme caution when positioning

breakage potential when making angle and scroll cuts.

blades without the proper blade adapter.

Always be aware of increased tool vibration, kickback, and blade

Use only recommended blades with this tool. Do NOT use jig saw

TO START AND STOP THE SAW

1. Make sure that the switch is off and the power circuit voltage is the same as that shown on the specification plate of the saw. Connect the saw to the power source.

2. Hold the saw firmly (see Fig. 14 or Fig.15). Squeeze the trigger switch (A) Fig. 16 to start the motor. Release the trigger to stop the motor.

Fig. 16

VARIABLE SPEED

The saw is equipped with a variable speed control switch (A) Fig. 16 (0 to 2900 SPM). As the switch trigger is squeezed, the speed of the saw blade increases.

The lower speeds are recommended for most metal cutting, while the higher speeds are recommended for wood. A few practice cuts at various speeds on scrap material

will aid you to choose the best speed for maimum results.

BEFORE YOU START TO WORK

Select the blade best suited for the workpiece. For greatest economy, use the shortest blade suitable for the thickness of the workpiece.

Be sure that the workpiece is rigid. Clamp small workpieces securely in a bench vise or to the work table. As the work progresses in scroll or curved cut-out pieces, readjust the material to accommodate the movement of the saw. The saw cuts freely with only

slight feed pressure. Forcing the saw will not make it cut faster.

SAWING WOOD

The variable angle reciprocating saw is used much the same as a hand saw in that it moves toward the operator during the cutting operation.

However, since the blade cuts on the up-stroke instead of the down-stroke as in the case of the hand saw, the good or finish side of the work should face down during the cutting operation.

TROUBLESHOOTING

For assistance with your tool, visit our website at www.porter-cable.com for a list of service centers, or call the Porter-Cable Customer Care Center at 1-888-848-5175.

MAINTENANCE

KEEP TOOL CLEAN

Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.

Wear ANSI Z87.1 safety glasses while using compressed air.

FAILURE TO START

Should your tool fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit breakers in the line.

LUBRICATION

This tool has been lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. No further lubrication is necessary.

BRUSH INSPECTION (If applicable) For your continued safety and electrical protection, brush inspection and replacement

on this tool should ONLY be performed by an AUTHORIZED PORTER-CABLE SERVICE STATION or a PORTER-CABLE•DELTA FACTORY SERVICE CENTER.

At approximately 100 hours of use, take or send your tool to your nearest authorized PorterCable Service Station to be thoroughly cleaned and inspected. Have worn parts replaced and lubricated with fresh lubricant. Have new brushes installed, and test the tool for performance.

Any loss of power before the above maintenance check may indicate the need for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE TOOL UNDER THIS CONDITION. If proper operating voltage is present, return your tool to the service station for immediate service.

SERVICE

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our website at servicenet.porter-cable.com. You can also order parts from your nearest factory-owned branch, or by calling our Customer Care Center at 1-888-848-5175 to receive personalized

support from highly-trained technicians.

SERVICE AND REPAIRS

All quality tools will eventually require servicing and/or replacement of parts. For information about Porter-Cable, its factory-owned branches, or an Authorized Warranty Service Center, visit our website at www.porter-cable. com or call our Customer Care Center at 1-888-848-5175. All repairs made by our service centers are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by others.

You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North, Jackson, Tennessee 38305 - Attention: Product Service. Be sure to include all of the information shown on the nameplate of your tool (model number, type, serial number, etc.).

ACCESSORIES

A complete line of accessories is available from your Porter-Cable•Delta Supplier, PorterCable•Delta Factory Service Centers, and Porter-Cable Authorized Service Stations. Please visit our Web Site www.porter-cable. com for a catalog or for the name of your nearest supplier.

Since accessories other than those offered by Porter-Cable•Delta

could be hazardous. For safest operation, only Porter-Cable•Delta recommended accessories should be used with this product.

have not been tested with this product, use of such accessories

+ 33 hidden pages