Owner’s
Manual
RTi100
Floorstanding Loudspeaker
RTi SERIES
Contact Polk Audio Customer Service 1-800-377-7655 (Outside US: 410-358-3600), polkcs@polkaudio.com
SAFETYPRECAUTIONS—
READ FIRST!
1. Read the instructions.
All the safety and operating instructions should
be read before the product is operated.
2. Retain instructions.
Safety and operating instructions should be
retained for future reference.
3. Heed warnings.
All warnings on the product and in the operating
instructions should be adhered to.
4. Follow instructions.
All operating and use instructions should be followed.
5. Water and moisture.
Product should not be used near water—for example, near
a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool, etc.
6. Accessories.
Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing
serious injury to a child or adult, and serious damage to
the product. Use only with a cart, stand, tripod, bracket,
or table recommended by the manufacturer or sold with
the product. Any mounting of the product should follow the
manufacturer’s instructions, and should use a mounting
accessory recommended by the manufacturer.
7. Wall or ceiling mounting.
Product should be mounted on a wall or ceiling only
when and as recommended by the manufacturer.
8. Ventilation.
Cooling fins on the rear of the amplifier are provided for
ventilation, to ensure reliable operation of the product, and
to protect it from overheating. Fins must not be blocked or
covered. The fins should never be blocked by placing product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or
the manufacturer’s instructions have been adhered to.
9. Heat.
Product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products
that produce heat. If placed near an amplifier, check
with manufacturer for applicability.
10. Power sources.
This product should be operated only from the type of
power source indicated on the marking label. If you are not
sure of the type of power supply to your home, consult your
product dealer or local power company.
11. Grounding or polarization.
This product may be equipped with a polarized alternating
current line plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to replace
your obsolete outlet. Do not defeat the safety purpose of
this polarized plug.
12. Power cord protection.
Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit
from the product.
13. Cleaning.
Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
14. Nonuse periods.
The cord of the product should be unplugged from the
outlet when left unused for long periods of time.
15. Lightning.
For added protection for this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage
to the product due to lightning and power-line surges.
16. Overloading.
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of
fire or electric shock.
17. Object and liquid entry.
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short out parts that could result in fire or electric shock.
Never spill liquid of any kind on the product.
18. Damage requiring service.
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a) Power supply cord or plug has been damaged.
b) Objects have fallen into, or liquid has spilled into, the
product, or
c) Product has been exposed to rain or water, or
d) Product does not operate normally when following
operating instructions. Adjust only those controls that
are covered by the operating instructions, as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to its normal operation; or
e) Product has been dropped, or enclosure damaged; or
f) Product does not appear to operate normally or exhibits
a marked change in performance.
19. Attachments.
Do not use attachments not recommended by the product
manufacturer as these may cause hazards.
20. Replacement parts.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or other hazards.
21. Safety check.
Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that product is in proper operating condition.
22. Servicing.
Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to
qualified service personnel.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS: RISQUE DE CHOC ÉLECTRIQUE. NE PAS OUVRIR.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING
TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULL Y INSERT.
ATTENTION:
POUR ÉVITER LES CHOCS ÉLECTRIQUES INTRODUIRE LA LAME LA PLUS LARGE DE
LA FICHE DANS LA BORNE CORRESPONDANTE DE
LA PRISE ET POUSSER JUSQU’AU FOND.
FIGURE 1
Create an equilateral triangle between the speakers and the listening position.
RTi Series Loudspeakers are magnetically shielded for safe placement near TV or video monitors.
If you notice video distortion or discoloration, immediately move the speakers away from the video
source and call Polk Audio Customer Service 800.377.7655 (US and Canada) or polkcs@polkaudio.com.
Haga un triángulo equilátero con los altavoces y la posición de audición.
Créez un triangle équilatéral entre les enceintes et la position d’écoute.
Bilden Sie ein Dreieck zwischen den Lautsprechern und Ihrer Hörposition.
FIGURE 2
For stability on carpet, use spikes. For stability on hard floors, use rubber feet over spikes.
Use púas para estabilizar los altavoces sobre una alfombra.
Use patas de goma sobre las púas para estabilizarlos sobre pisos duros.
Pour plus de stabilité sur tapis, utilisez les picots.
Sur planchers, recouvrez les picots des pieds de caoutchouc.
Die Verwendung von Befestigungsstutzen gewährleistet die Stabilität der Lautsprecher
bei Platzierung auf Teppichböden. Auf hartem Untergrund sollten die Stutzen mit
Gummifüßen überzogen werden.
Left Speaker Right Speaker
for more information visit our website at www.polkaudio.com
FIGURE 1
FIGURE 2
PLACEMENT RECOMMENDATIONS
FOR RTi SERIES FLOORSTANDING LOUDSPEAKERS
To get the most realistic stereo image and lifelike sound, place the speakers so that an equilateral
triangle is created between the speakers and your favorite listening position [figure 1]. Your RTi
Series Loudspeakers are magnetically shielded for safe placement near your TV or video monitor.
If you notice video distortion or discoloration, immediately move the speakers away from the TV
and call Polk Audio Customer Service 800-377-7655 (US and Canada) or polkcs@polkaudio.com.
If your room arrangement forces you to place the speakers farther apart than the distance from
which you are listening, angle the speakers toward the middle in order to support a more solid
center image. Rubber feet and adjustable carpet spikes are included to provide stability on any
type of floor. To install them, lay the speaker carefully on its side and screw in the spikes as far as
they will go into the threaded inserts in the base of the speaker. For wood or tile floors, slip a
rubber foot over each spike. For carpeted floors, use bare spikes [figure 2]. You will achieve
optimum performance when the speaker is level and stable in all directions.
POLK AUDIO—A PASSION FOR SOUND
Thank you for purchasing this Polk Audio loudspeaker. Since its start in 1972, Polk Audio has been dedicated to audio
products that emphasize superior sound and build quality, as well as an ever-evolving standard for performance. It’s our
mission to provide these great products at a reasonable price for the enjoyment of people like you, who love good sound.
Our thirty years of R&D, resulting in over 45 worldwide patents for loudspeaker technology and innovation, has solidi-
fied our reputation as “The Speaker Specialists,” and demonstrated that for the people here at Polk Audio, building
speakers is not just a job; it’s a passion. Welcome to the Polk Audio family!
CONNECTION OPTIONS FOR
RTi SERIES FLOORSTANDING LOUDSPEAKERS
Follow the hookup directions included with your receiver. Strip 1/2 inch (12.7mm) of insulation
from each of the two conductors of the speaker wire to expose the bare metal and twist each of the
individual conductors into single unfrayed strands. Note that one of the terminals on the rear of
each speaker is red (+) and the other is black (-). Make certain that you connect the wire from the
red (+) terminal of your amplifier or receiver to the red (+) terminal on your speaker and the wire
from the black (-) terminal of your amplifier or receiver to the black (-) terminal on your speaker.
Most wire has some indicator (such as color-coding, ribbing or writing) on one of the two
conductors to help you maintain consistency.
To connect wire to the binding post [figure 3], unscrew the hex nut and insert the bare wire into
the hole near the base of the binding post. Do not insert the insulated part of the wire into the hole
as this will not give you a good connection. Twist the hex nut back down the binding post until it
firmly meets the wire. Do not over tighten.
To Use Banana Plugs (US Only): Unscrew the binding post lug nuts completely to expose the
binding post plugs (plastic plugs inserted into the binding posts). Carefully pry out the binding post
plugs to expose banana plug holes. Screw the lug nuts back on the binding posts and insert banana
plugs. (This is for US owners only.)
HOOK UP OPTION 1 [figure 4] is recommended for most systems. Make sure the flat metal
jumper strips are tightly secured to both sets of binding posts.
HOOK UP OPTION 2 [figure 5] is recommend for use with a receivers or preamp/processors
with L & R preamp outputs. For this connection, remove the flat metal jumper strips. Connect
the top set of binding posts to the speaker outputs of your amp or receiver, If your pre-amp,
processor, amplifier or receiver has a spare set of front left and right pre-outputs, connect them
to the subwoofer inputs on the back of the speakers. If your electronics has a single set of pre-
outputs and they are being used to deliver signal to an amplifier, use “Y” cables.
HOOK UP OPTION 3 [figure 6] is recommended for systems with receivers or preamp/pro-
cessors with unfiltered
subwoofer (LFE) outputs only. (To find out if your subwoofer output jack is
unfiltered, please see your receiver/preamp/processor’s owner’s manual.) For this connection,
remove the flat metal jumper strips. Connect the line level inputs on the back of the loudspeaker to
the subwoofer output(s) of your pre-amp, processor, amplifier or receiver. If you only have one
subwoofer output jack, run a cable to the subwoofer line level input of one speaker and another
cable from the line level output of that speaker to the line level input of the other speaker.
If you are not sure about the nature of your subwoofer output jack, use either hookup option 1 or
hookup option 2.
FOR MANUAL UPDATES, VISIT
http://www.polkaudio.com/home/products/floorstanding/rti25
FOR MORE DETAILED HOOKUP AND PLACEMENT INFORMATION, VISIT
http://www.polkaudio.com/home/faqad/
FOR RECOMMENDED ACCESSORIES (INCLUDING SPEAKER STANDS, BRACKETS AND
EXCLUSIVE POLK AUDIO LOGOWEAR), VISIT OUR WEBSTORE:
http://shop.polkaudio.com/
Contact Polk Audio Customer Service 1-800-377-7655 (Outside US: 410-358-3600), polkcs@polkaudio.com
FIGURE 4
Option 1, recommended for most systems.
BASS MANAGEMENT SETTINGS: Front = Large
Opción 1, recomendada para la mayoría de los sistemas.
PARÁMETROS DE CONTROL DE BAJAS FRECUENCIAS: Front = Grande (Large)
Option 1, recommandée pour la plupart des systèmes.
Réglages: (Bass Management Settings) Front (avant) = Large
Option 1, empfohlen für die meisten Lautsprecher.
EINSTELLUNG DER TIEFENTONLAGEN: Vorne = Groß
FIGURE 5
Option 2, for systems with preamp outputs.
BASS MANAGEMENT SETTINGS:
With NO separate subwoofer: Front = Large Sub = No
WITH separate sub: Front = Large Sub = Yes
Opción 2, para sistemas con salidas de preamplificador.
PARÁMETROS DE CONTROL DE BAJAS FRECUENCIAS:
2a: Front = Grande (Large) Sub = No
2b: Front = Grande (Large) Sub = Sí
Option 2, pour systèmes avec sorties préamplificateur.
RÉGLAGES: (BASS MANAGEMENT SETTINGS)
2a: Front (avant) = Large Sub = No
2b: Front (avant) = Large Sub = Yes
Option 2, für Systeme mit Vorverstärker-Ausgängen.
EINSTELLUNG DER TIEFENTONLAGEN:
2a: Vorne = Groß Subwoofer = Keine
2b: Vorne = Groß Subwoofer = Ja
FIGURE 6
Option 3, for systems with both unfiltered subwoofer
outputs and no separate dedicated sub.
BASS MANAGEMENT SETTINGS:
Front = Small Sub = Yes
Opción 3, para sistemas con ambas salidas de subwoofer sin filtrar y sin subwoofer dedicado separado.
PARÁMETROS DE CONTROL DE BAJAS FRECUENCIAS:
Front = Pequeño (Small) Sub = Sí
Option 3, pour systèmes avec deux sorties subwoofer
sans filtre et sans sortie subwoofer dédiée distincte.
RÉGLAGES: (BASS MANAGEMENT SETTINGS):
Front = Small Sub = Yes
Option 3, für Systeme sowohl mit nicht gefilterten
Subwoofer-Ausgängen als auch ohne separaten
(dedizierten) Subwoofer.
EINSTELLUNG DER TIEFENTONLAGEN:
Vor ne = Klein Subwoofer = Ja
for more information visit our website at www.polkaudio.com
FIGURE 4FIGURE 5FIGURE 6
FIGURE 3
Using binding post connections.
Uso de conexiones con tornillos de presión.
Utilisation des bornes de branchement.
Verwendung von Anschlussklemmen.
Loosen hex nut
Desenrosque parcialmente
la tuerca hexagonal
Desserrer l’écrou
Sechskantmutter lösen
Insert speaker wire through
hole
Inserte el alambre para la
bocina en el orificio
Insérer le fil du haut-parleur
dans le trou
Lautsprecher-Draht durch
das Loch schieben
Tighten hex nut
Enrosque la tuerca de nuevo
Serrer l’écrou
Sechskantmutter festschrauben
Do not insert insulated
section of speaker wire
No inserte alambre con
material aislante
Ne pas insérer la partie
isolée du fil du haut-parleur
Isolation des LautsprecherDrahtes nicht in das
Loch schieben
FIGURE 3
To use Banana Plugs (US only):
Unscrew the binding post lug nuts completely to
expose the binding post plugs (plastic plugs inserted into the binding posts). Carefully pry out the
binding post plugs to expose banana plug holes.
Screw the lug nuts back on the binding posts and
insert banana plugs. (This is for US owners only.)
HIGH LEVEL
INPUT
SUB OUT
HIGH LEVEL
INPUT
SEPARATE SUB
(OPTIONAL)
HIGH LEVEL
INPUT
HIGH LEVEL
INPUT
SETTING THE VOLUME
Volume level for the built-in subwoofer is adjusted using the volume control knob located on the
rear plate of the amplifier [figure 7]. Set this control by ear using a wide variety of music and
movie sources.
SAFE LIMITS OF OPERATION
Your Polk loudspeakers are made with the highest quality materials for years of trouble-free
performance. However, damage to loudspeakers can occur when an amplifier, regardless of its
wattage, is made to play at higher listening levels than its power can clearly produce (usually
beyond the “1 to 2 o'clock” position on the volume control). This results in very high levels of
audible distortion, originating in the amplifier, that can add a harsh, gritty sound to music.
Contrary to popular belief, a speaker is more likely to be damaged by trying to get too much
volume from a low-powered amp or receiver than from a high powered one.
AC POWER
This RTi powered loudspeaker has a built-in power amplifier and must be plugged into a
standard household AC power source in order to operate properly.
The power switch on the rear amp plate [figure 7] has two positions, “Off” and “Auto,” and a
small LED light. The LED will glow green at all times that the powered loudspeaker is plugged
in (even if the speaker is set to “Off”). We meant it that way.
To play, set the switch in the “Auto” position. Set to the “Auto” position, the amplifier will automatically turn on as soon as the speaker senses a signal coming from your pre-amp, integrated
amp or receiver. It will automatically turn off several minutes after signals cease to be sent
by your pre-amp, integrated amp or receiver. The LED will glow green at all times.
TAKING CARE OF YOUR
RTi SERIES FLOORSTANDING LOUDSPEAKERS
Avoid harsh detergents and cleaning fluids [figure 8]. Clean and dust the veneer with a damp
cloth only. Do not use furniture polish on the veneer. Carefully vacuum the grilles to remove dust.
Contact Polk Audio Customer Service 1-800-377-7655 (Outside US: 410-358-3600), polkcs@polkaudio.com
FIGURE 8
Clean veneer with a damp cloth. Do not use furniture polish.
Cuidado del acabado de madera natural.
Entretien de la finition en bois véritable.
Pflege der Holzappretur.
for more information visit our website at www.polkaudio.com
FIGURE 8
FIGURE 7
RTi powered loudspeaker Amplifier panel
Tablero del Amplificador para la bocina RTi de potencia
Enceinte amplifiée panneau de l’amplificateur
Rückseite des aktiven RTi Lautsprechers
FIGURE 7
IN OUT
Subwoofer Line Level
High Level Input
+
-
VOLUME
CONTROL
OFF
AUTO
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
AVERTISSEMENT
AFIN D’ÉVITER TOUT RISQUE D’INCENDIE OU D’ÉLECTROCUTION,
NE PAS EXPOSER CET APPAREIL À LA PLUIE OU À L’HUMIDITÉ.
AUCUNE PIÈCE RÉPARABLE PAR L’UTILISATEUR NE SE TROUVE À L’INTÉRIEUR. CONFIER TOUT ENTRETIEN À DES TECHNICIENS QUALIFIÉS.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS: RISQUE DE CHOC ÉLECTRIQUE. NE PAS OUVRIR.
Speaker
Remove
jumpers
when using
subwoofer line
level input
(see owner’s
manual).
Subwoofer
POWERED TOWER
the speaker specialists
®
POLK AUDIO, INC. • 5601 METRO DRIVE, BALTIMORE, MD 21215 USA
800.377.7655 • FAX: 410.358.2870 • WWW.POLKAUDIO.COM
RM0368-1
LIMITED FIVE YEAR WARRANTY
Polk Audio, Inc. warrants to the original purchaser only that this Polk Audio Loudspeaker Product (the “Product”) will be free from defects in materials and
workmanship for a period of five (5) years from the date of original retail purchase from a Polk Audio Authorized Dealer. However, this Warranty will automatically
terminate prior to the expiration of the five (5) years if the original retail purchaser sells or otherwise transfers the Product to any other party. The original retail
purchaser shall hereinafter be referred to as “you.” To allow Polk Audio to offer the best possible warranty service, please fill out the Product Registration Card(s)
and send it to the Factory, at the address provided on the Product Cards(s) within ten (10) days of the date of purchase.
Defective Products must be shipped, together with proof of purchase, prepaid insured to the Polk Audio Authorized Dealer from whom you purchased the Product,
or to the Factory at 2550 Britannia Boulevard, Suite D, San Diego, California 92154. Products must be shipped in the original shipping container or its equivalent;
in any case the risk of loss or damage in transit is to be borne by you. If upon examination at the Factory or Polk Audio Authorized Dealer it is determined that the
unit was defective in materials or workmanship at any time during this Warranty period, Polk Audio or the Polk Audio Authorized Dealer will, at its option, repair
or replace this Product at no additional charge, except as set forth below. All replaced parts and Products become the property of Polk Audio. Products replaced
or repaired under this warranty will be returned to you, within a reasonable time, freight prepaid.
This warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate packing or shipping procedures, commercial use, voltage inputs in excess of the rated maximum of the unit, cosmetic appearance of cabinetry not directly attributable to defect in materials
or workmanship, or service, repair, or modification of the Product which has not been authorized or approved by Polk Audio. This warranty shall terminate if the
Serial number on the Product has been removed, tampered with or defaced.
This warranty is in lieu of all other expressed Warranties. If this Product is defective in materials or workmanship as warranted above, your sole remedy shall
be repair or replacement as provided above. In no event will Polk Audio, Inc. be liable to you for any incidental or consequential damages arising out of the use
or inability to use the Product, even if Polk Audio, Inc. or a Polk Audio Authorized Dealer has been advised of the possibility of such damages, or for any claim by
any other party. Some states do not allow the exclusion or limitation of consequential damages, so the above limitation and exclusion may not apply to you.
All implied warranties on this Product are limited to the duration of this expressed Warranty. Some states do not allow limitation on how long an implied Warranty
lasts, so the above limitations may not apply to you. This Warranty gives you specific legal rights, and you also may have other rights which vary from state to state.
This Warranty applies only to Products purchased in the United States of America, its possessions, and U.S. and NATO armed forces exchanges and audio clubs.
The Warranty terms and conditions applicable to Products purchased in other countries are available from the Polk Audio Authorized Distributors in such countries.
SPECIFICATIONS
RTi100
DRIVER COMPLEMENT:
62"(16.5cm) driver
1"(2.5cm) tweeter
62"(16.5cm) subwoofer
OVERALL FREQUENCY RESPONSE:
25Hz-27kHz
-3DB LIMITS:
36Hz-26kHz
RECOMMENDED AMPLIFICATION:
20-250 watts/channel
IMPEDANCE:
Compatible with 8 Ohm Outputs
SUBWOOFER POWER OUTPUT (DYNAMIC):
35 watts
SUBWOOFER POWER OUTPUT (FTC):
80 watts
CROSSOVER FREQUENCY:
85Hz, 2.1k
CROSSOVER SLOPE:
2nd Order HP, 2nd Order LP
ENCLOSURE TYPE:
Driver Sealed/Subwoofer Bandpass PowerPort
DIMENSIONS:
43
1
⁄4"H x 81⁄4"W x 113⁄8"D
(109.9cmH x 20.9cmW x 28.9cmD)
BASE DIMENSIONS:
9"W x 12
1
⁄4"D
(22.9cmW x 31.1cmD)
SHIPPING WEIGHT:
63 lbs. (29kg.) each
the speaker specialists
™
Loading...