Instruction manual
PS300 Your mobile outlet to go
Mobile Storage System
Thank you for purchasing PS300 from Polaroid. To safely use this device, please read this manual carefully and keep
it (together with the warranty card) in a safe place. If you pass the mobile storage system on to another user, make
sure that you hand over the instruction manual and warranty card as well. Please keep any additional documents
together with this manual.
CHARGE FIRST! Before reading through the manual, you can begin to charge up your PS300
by connecting it to the power supply provided and plugging it in at the wall.
Noncompliance with the safety instructions may cause injuries due to re, electric shock, etc.
Contents
1. Set includes 4
2. Introduction 5
3. Safety instructions 6
4. Lifting and transportation 10
5. Get to know your PS300 11
6. Charging 12
6.1. What it can power 12
6.2. LCD battery display 12
6.3. Charging via solar panel 13
6.4. Charging via mains power supply 13
7. Using the PS300 14
8. Technical specications 15
9. Solar panels 16
10. Troubleshooting 16
11. Storage 17
12. Service life of lithium ion batteries 17
13. Frequently Asked Questions (FAQs) 18
14. Disposal and recycling 20
15. Warranty and customer service 21
Appendix: Product warranty card
Instruction manual
PS300 Mobile Storage System
1. Set includes
No. Item Quantity
1 PS300 Mobile Storage System 1
2 AC Wall Charger (2 pieces) 1
3 Instruction manual and warranty card 1
4 100W external inverter 1
Instruction manual | PS300 Mobile Storage System
2
1
3 4
4
Instruction manual | PS300 Mobile Storage System
2. Introduction
Congratulations on purchasing Polaroid PS300 Mobile Storage System, a plug-and-play power supply for outdoor use. With 289.5 watt-hours of stored energy, you can keep appliances, or electronic devices running for
hours.
The Polaroid PS300 Mobile Storage System is designed to keep you powered up outdoor in your RV during
emergencies or power outages.
Note the following points while reading through this instruction manual:
•This manual was prepared with care and to the best of our knowledge.
Contact us, should you have any questions relating to the product.
•This manual may not be copied or duplicated, except for personal use.
Disclaimer
•Our company cannot be held liable for damages caused by re, earthquake, use by a third party, other
accidents, intentional misconduct on the part of the customer, abuse or other abnormal conditions.
•Do not repair any damage to the AC plug or power supply on your own.
•The warranty covers all terms and conditions of the warranty. Contents that are not specied in the war-
ranty terms and conditions are beyond our responsibility.
•Our company assumes no liability for damages caused by incorrect use or non-compliance with this
instruction manual.
•This instruction manual can be downloaded as a PDF le on our website:
www.polaroidenergystorage.com.
•Intended use: The Polaroid PS300 Mobile Storage System unit is intended as a power supply for electro-
nic devices with a maximum power consumption of 100 W. Our product is not suitable to be used with
equipment that relates to one‘s own personal safety and relies heavily on electricity, such as medical devices, equipment for nuclear facilities, the manufacture of air and spacecraft, etc. We therefore assume no
liability for accidents involving personal safety, res or machine failures caused by using our product with
the aforementioned devices.
5
3. Safety instructions
Observe these instructions to ensure safe usage.
Explanation of symbols
Instruction manual | PS300 Mobile Storage System
This symbol together with
DANGER means
This symbol together with
WARNING means
This symbol together with
CAUTION means
This symbol together with
ATTENTION means
•Serious injuries include blindness, burns, electric shock, fractures, poisoning, etc., which can lead to
complications, hospitalization or permanent treatment.
•Injuries include burns, electric shock, etc., which do not lead to hospitalization or permanent treatment.
•Property damage: includes buildings, belongings and pets, etc.
A warning label has been attached to the PS300 unit to ensure its safe use. Use the unit only in accordance
with the manual and the instructions provided on the label.
Make sure that the label is always clean and legible and do not remove it.
Noncompliance may very likely lead
to serious injury or death.
Noncompliance may lead
to serious injury or death.
Noncompliance may lead
to injuries and/or property damage.
Noncompliance may damage the unit.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
6
Instruction manual | PS300 Mobile Storage System
Danger
Do NOT disassemble, repair or modify the unit or the battery.
Doing so may result in electric shock, re, etc.
Do NOT place the unit close to or in a re or expose it to heat. Keep out of direct sunlight.
Doing so may result in re or injuries.
Do NOT charge, use or store the unit in a bathroom or in an area exposed to rain or moisture.
Doing so may result in electric shock, re, etc.
Only use the output socket to power external devices. Never connect the output to mains power
under any circumstances.
Connecting to the mains may lead to electric shock, injuries or re.
Do NOT touch the unit or the plug-in points if your hands are wet.
Doing so may result in electric shock.
Do NOT connect any metallic objects to the AC input or output.
Doing so may result in electric shock, re, etc.
Do NOT rub your eyes if uid from inside the unit should get in your eyes.
If this should occur, ush eyes with water and seek medical attention immediately. This can lead to blindness.
Do NOT dispose the unit together with household waste.
Follow the local law to dispose the unit.
Do NOT use any inappropriate power cords.
Doing so may result in electric shock, re, etc.
Do NOT operate the unit above the specied input voltage.
Doing so may result in electric shock, re, etc.
Do NOT use the unit if it is not functioning correctly.
Doing so may result in electric shock, re, damage to the unit, etc.
Do NOT move the unit if it is recharging or in use.
Doing so may result in electric shock, damage to the unit or other injuries.
7
Instruction manual | PS300 Mobile Storage System
Warning
Use and store the unit only in a clean and dry environment. Do not use and store in dusty and wet
envoirnment.
Failure to do so may result in a short circuit, smoke or re if metal dust or small metallic parts come in contact
with the connections.
Check the unit prior to every use. Do not use the unit if it is damaged, broken.
If you notice that the unit has any damage or cracks, is broken, or has other abnormalities, do NOT continue to
use the unit and contact your dealer or our customer service center.
Do not use the unit if the power cord is damaged or broken.
Keep the unit away from children. Do NOT let children use the power supply unit.
Doing so may result in an accident or injuries. This unit must not be used by children. The unit and its connection cables must be kept out of reach of children. Children must not play with the unit.
This unit may only be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they are monitored or have been instructed in how to safely use the unit and understand
the resulting risks.
Keep this product away from pets.
Do NOT use or store the unit in an area or environment with high temperature.
Doing so may cause the unit to deform or overheat.
Should uid from inside of the unit come in contact with your skin or clothing, wash the affected
areas with tap water.
Contact with the uid may result in injuries.
In a storm, unplug the power cord from the socket.
A storm may result in an overcurrent coming from the socket, resulting in overheating, re or other accidents.
Do NOT charge the unit via power supply systems that operate outside of 100-240V.
That may otherwise result in overheating, re, etc.
Do NOT place the unit on its side or upside down while in use or storage.
Doing so may result in leakage or cause the unit to overheat leading to other accidents.
8
Instruction manual | PS300 Mobile Storage System
Caution
If rust, peculiar odors, overheating or other abnormal circumstances are observed, stop using the unit immediately and contact the dealer or our customer service center.
The unit complies with all legal requirements for transport of dangerous goods.
The capacity of the lithium battery pack in the unit exceeds 100 Wh.
Based on international standards: If this unit is to be sent by airplane, it must be transported in accordance with
IATA standard packaging. IATA instructions and labelling requirements and the relevant declarations must be
completed.
Make sure that the unit is properly secured when transporting it in a motor vehicle.
Failure to do so may result in damage to the unit, electric shock, overheating, re and other accidents.
Only charge, use and store the unit within an ambient temperature of 0 to 40 °C (32 - 104 °F).
Operating the unit above or below this temperature range may result in overheating or reduced performance.
Switch the unit off immediately if it has accidentally fallen, was dropped or was exposed to vibrations.
To prevent accidents, please contact the dealer or our customer service center to have the unit checked and
repaired.
Carefully read the instructions for the electric devices that you intend to connect to your power
supply unit.
Make sure that the device you are connecting is switched off before you connect it.
A device starting up suddenly may lead to accidents or injuries.
If the protective function is activated and the output of the device is switched off, disconnect the electric devices from the power output. Switch the unit off in case of non-use/storage in order to prevent electric shock
and the battery from discharging unnecessarily, etc.
9
4. Lifting and transportation
1. Carry the unit with both hands.
Instruction manual | PS300 Mobile Storage System
ATTENTION
Keep the unit away from
other objects when moving.
2. Placing the unit on a stable surface.
Place the unit on a stable surface.
By doing so, it is easier to read the indicators.
3. Transporting the device.
ATTENTION
Take extra care to ensure that the unit is never
allowed to fall to the ground.
ATTENTION
DANGER
The unit should not be subjected to any impact or vibrations.
Otherwise there is a risk of re.
Keep the unit‘s original packaging and use it when you need to transport the unit.
10
Instruction manual | PS300 Mobile Storage System
DC Input port
Type-C port
DC Output port
Auto cigarette lighter port
LCD display
ON/OFF button
USB ports (4x)
5. Get to know your PS300
11
Instruction manual | PS300 Mobile Storage System
6. Charging
Before use or storage, plug your PS300 into the wall until it is fully charged. If the display shows less than 20%
capacity, plug it into a power source, like an AC outlet or a solar panel as soon as possible.
ATTENTION
Only charge the unit when the ambient temperature is between 0 and +40 °C (32 - 104 °F).
6.1. What it can power
...and many more
6.2. LCD battery display
The LCD Display indicates the percentage of total charge remaining in your PS300.
LCD Display
12
NOTE
Charging time may vary depending on the ambient temperature involving the solar charger.
End the charging process by switching off the unit and pulling the plug out of the socket.
Instruction manual | PS300 Mobile Storage System
6.3. Charging via solar panel (not included)
The 8mm input port is compatible with Polaroid SP50 solar panels with an input voltage of 18V.
1. Place your solar panel where it will get as much direct sunlight as possible. See the graphic in the solar
section for help.
2. Solar charge times depend on weather conditions.
6.4. Charging via mains power supply
Use the AC wall charger provided and plug your PS300 into any outlet. When the digital indicator shows 100,
your device is fully charged. It will be fully charged after 7-8 hrs.
The AC wall charger consists of two pieces.
Connect the two pieces by plugging the cable into the box.
13
Instruction manual | PS300 Mobile Storage System
7. Using the PS300
What to power from PS300
• USB: Smartphones, Digital Cameras, E-Readers, Tablets, Consoles, etc.
• 12V: Lights, DC devices etc.
• AC: Laptops, Display Monitors, Appliances, etc.
How to use PS300
1. Press the power button underneath the LCD display.
2. You‘ll know your device is working when the LCD displays the percentage charge remaining.
3. Plug in your device for mobile power.
Best-use strategy
• When charging devices with PS300, take note of the LCD Display.
• If you plug in devices that have a high power requirement, the charge level of PS300 can drop quickly and
you may not get be able to extract the entire 289.5 Wh of energy.
• If you’re charging devices that draw power slowly (e.g., a tablet), you will be able to extract close to the
full 289.5 Wh out of PS300. If you’re experiencing shorter run times, you can check the device’s power
requirements.
Appropriate temperature usage
• Cold temperatures can impact both the PS300 battery capacity and the output power.
• The PS300 can power your devices at temperatures ranging from 0 - 40°C (32 - 104 °F). If your working
temperature is outside this range, the PS300 may stop working.
ATTENTION
Make sure that the electronic device you are powering works properly prior to use.
The max. power consumption for electronic devices is 100 W.
Due to the different types of electric devices, it is possible that they may not operate
even if their power consumption is less than 100 W.
14
Instruction manual | PS300 Mobile Storage System
8. Technical specications
Wall charger (12V 3.5A) 8.5 hrs
Solar panel (50 W) 6-7 hrs (Full Sun)
Cell type Lithium-ion
Pack capacity 289.5 Wh
Lifecycles >300
Charge times
Battery
Management system
Ports
1x DC (input) 12V, 3.5A
4x USB ports (output) 5V, 2.4A (Total 4.8A)
1x Type-C port (output) 3A max.
1x DC car outlet 12V, 10A
1x DC outlet 12V, 3A
General
Weight 2,11 kg (4.65 lbs)
Operating temperature 0 - 40 °C (32 - 104 °F)
Certicates FCC, ROHS, UN38.3
Warranty 24 months
Temperature control, Surge protection,
Short circuit protection
15
Instruction manual | PS300 Mobile Storage System
9. Solar panels
PS300 makes it easy to recharge your device using solar power – we didn’t invent solar power, we perfected it.
Some things to keep in mind when recharging your device using solar power:
1. Solar panels don’t store energy from the sun, they collect it.
Use your solar panel to charge your PS300 so that you can use it day or night to power your devices.
2. Not all solar charge times are created equal.
Most solar panel manufacturers calculate recharge times using the following equation:
Devices Watt Hours / Solar Panel Watts = Solar Recharge Times.
So theoretically, a 13 watt solar panel would charge a 50 watt-hour battery pack in 3.84 hours (50/13 = 3.84) –
and this is the number you could nd in marketing material for a solar panel. However, in order to standardize
results across all manufacturers, these tests are completed in laboratory settings. The truth is, on a good, sunny
day, you’ll received about 50-75% of your solar panel’s rated wattage.
3. Solar panels generate power even in overcast conditions.
Solar panels utilize IR, UV, and visible rays from the sun that can penetrate through clouds. Although the
efciency of the solar panel will decrease in cloudy conditions, you’ll still be collecting valuable energy from
the sun.
4. Don‘t place the solar panel in shaded areas or behind windows.
Although you should seek out the shade on sunny days, your solar panels will collect more energy when fully
exposed to the sunlight. Windows also have a habit of decreasing efciency. So keep those panels outside and
in the bright sunlight.
5. Proper alignment works wonders.
Keeping your solar panel angled toward the sun can dramatically increase solar efciency. Set it up and let
mother nature do the rest.
10. Troubleshooting
If your device is not being powered correctly or isn‘t charging when connected to your PS300, check
the remaining charge by pressing the ON/OFF button.
1. Ensure the device has been switched on and the LED is showing the percentage of remaining charge.
16
2. Check the battery display. If it is at 20% or below, recharge your PS300.
3. Verify your device is suitable for use with the PS300.
a. All PS300 output ports have their own max. power. Check the PS300’s technical specications to ensure
your device is compatible.
What should I do if the unit gets wet?
Immediately turn off the unit and wait until you are certain that it is completely dry before turning it back on.
If you are unsure about when it is safe to turn it back on, please contact after sales service.
Instruction manual | PS300 Mobile Storage System
11. Storage
1. Charging to maximum capacity
Fully charge the power supply unit prior to long-term storage. Charge the power supply unit at least once every
three months.
2. Turn off all switches
As soon as the PS300 power supply unit is charged fully, switch off the main switch and the other ON/OFF
buttons and disconnect the adaptor from the main unit.
3. Cleaning
Wipe away any dirt using a damp cloth.
ATTENTION
Gasoline, thinner, kerosene, petroleum, etc. have the characteristics of solvents.
Do not use.
4. Storage
Store the power supply unit only in a dry and dust-free environment which is out of reach of children. Suitable
storage temperature: 0 to 40°C (32 - 104 °F). Keep out of direct sunlight. Make sure that the unit rests on a
stable surface.
12. Service life of lithium ion batteries
Charge, supply current and store between 0 and 40°C (32 - 104 °F).
Using the battery at temperatures outside the lower and upper limits reduces the battery‘s running time.
Do not connect a continuous load of more than 100 W.
The unit‘s output stops automatically in case of overloading, since it reduces the running time of the battery.
Do not continue to charge the battery after it has charged completely.
Pay attention to the indicated capacity. Do not charge the battery once it has been fully charged or the charging
process has been concluded. Otherwise the service life of the lithium battery may be reduced.
Switch off the unit if it is not being used.
Unnecessary power consumption also reduces the running time of the lithium battery.
Fully charge the battery prior to placing it in storage.
Fully charge the power supply unit prior to lengthy periods of non-use for storage and recharge the unit. After
prolonged storage, it may be necessary to charge and discharge the battery several times in order to reach full
capacity.
17
Instruction manual | PS300 Mobile Storage System
13. Frequently Asked Questions (FAQs)
What type of battery is in a PS300?
PS300 contains a battery pack which consists of an array of cylindrical 18650 LG lithium battery cells with high
energy density.
How do I know if my PS300 is charged?
To check the charge level of the PS300, refer to the LCD Battery Display.
Can I charge the PS300 while supplying power at same time?
The PS300 power supply unit can be used to charge the devices during the charging process of the unit itself.
Can I take my PS300 on a plane?
No, you can’t. PS300 contains a large number of lithium-ion batteries with a capacity considered to be hazardous by airlines.
How do I know if my device will work with the PS300?
You will need to check the amount of power your device requires. This may require some research on your end.
An online search or examining the user guide for your device should sufce. To be compatible with the PS300,
you should use devices that require less than 100 W.
How do I connect my PS300 to the external inverter?
Insert your Polaroid 100W inverter into the cigarette lighter output of your PS300 in the same way you would
with your car‘s cigarette lighter.
18
Auto cigarette lighter port
Instruction manual | PS300 Mobile Storage System
How long will the PS300 run my device?
Here are some common devices and their power requirements.
Device Lithium Power from PS300-ion
LED Light (3 W) ~90 hrs
Smartphones (5 W) ~60 recharges
Laptop (60 W) ~4 recharges
Console (95 W) ~3 hrs
Mini Fridge (70 W) ~4 hrs
When you’re deciding on what to power using your PS300 recharge, do some research into your device’s power
consumption. For more quick tips and learning tools, please email our customer service for help.
NOTE
The above data are to be used only as reference points.
The approximate values were determined at an ambient temperature of 25°C (77°F) and with a fully char-
ged battery. These values may vary, depending on the manufacturer of the electric device, unit, etc.
Certain types of devices may not operate, even if the output of the power supply unit is below 100 W.
In case of overload, the unit switches off automatically and the output is interrupted.
Desktop computers, and other devices with high power consumption, as well as household devices
with uctuating power consumption or with power factor correction may not operate normally or at all,
even if the their specied operating power is below 100 W.
19
Instruction manual | PS300 Mobile Storage System
14. Disposal and recycling
Lithium ion battery
As soon as the end of the battery‘s service life is reached, the entire lithium ion battery can
be recycled. Do not open or disassemble the unit.
Electric device
Old electric devices may not be disposed together with normal household waste. According to the directive 2012/19/EU, the device must be disposed of in a controlled manner
at the end of its service life. The recyclable materials contained in the unit shall be sent to
recycling to reduce the burden on the environment.
This unit contains lithium ion batteries. These are hazardous materials and are subject to specic transport and
handling regulations. Lithium ion batteries may ignite or explode if handled incorrectly.
For the safe disposal of the unit, contact a collection point or your local municipality for more information and
indicate that the unit contains lithium batteries.
Package
The product package consists of recyclable materials. Dispose of these in an environmentally friendly manner
and sort the materials in the provided collection systems.
20
Instruction manual | PS300 Mobile Storage System
15. Warranty and customer service
Contact distributor for technical support /customer service
USA [Style Asia Inc.]
101 Moonachie Ave
Moonachie, NJ 07074
USA
An Gut Nazareth 18A
52353 Düren
Germany
Unit 94 & 96 Allandale Business Park
CNR Morkels & Le Roux
Halfway House
Midrand, Johannesburg
South Africa
Toll-Free:
888-765-5428
polaroidenergy@digitalsupportdesk.com
EUROPE [GBT GmbH]
Telephone:
+49 (0) 2421 / 20 85 60
AFRICA [GBLT South Africa]
Telephone:
+27 (0) 11 / 516 0001
E-Mail:
E-Mail:
info@gbt-international.com
E-Mail:
sales@gbt-international.co.za
AUSTRALIA [NISTU Energy Innovations]
1/29 Thorne St Widsor
Queensland 4030
Australia
Telephone:
+61 (0) 403 / 655 873
E-Mail:
stuart.holt@gbt-international.com
21
Instruction manual | PS300 Mobile Storage System
REPAIR TERMS AND CONDITIONS
1. In the case of device failure which can be attributed to poor workmanship, please take the original sales
receipt with purchase date (invoice, etc.) to the retail store. In case of normal use, the power supply unit
will be repaired or replaced free of charge within the two year warranty period. In addition to that, the
customer must bear any shipping charges that may occur.
2. The repair is not free of charge in the following cases, even within the warranty period.
• A warranty card or certicate or sales receipt with purchase date (invoice, etc.) is not presented.
• The equipment failure was caused by improper use (including use that does not comply with the inst-
ructions set forth in the manual).
• Defects were caused by improper repairs, modications, disassembly, etc.
• Equipment failure was caused by careless operation (dropping /falling /impact /contact with uids/
deposits - on the inside or outside of the machine) or improper maintenance (mildew, dust, etc.).
• Damage was caused by use of unit for purposes other than intended (charged and recharged more
than 300 times, etc.)
• Equipment failure occurred due to external inuences, such as power supply or other electric devices
and/or damage during inspection or repair.
• Faults that can be attributed to causes that are not cited above are beyond our scope of responsibility.
3. Note that we do not assume any liability for consequential damages (foreseeable damages, psychological damages, etc.).
22
This product is manufactured, distributed and sold by GBT GmbH.
Polaroid, Polaroid & Pixel, Polaroid Classic Border Logo, and
Polaroid Colour Spectrum are trademarks of PLR IP Holdings, LLC,
used under licence. GBT GmbH provides a manufacturers warranty and support for this product. PLR IP Holding, LLC does not
manufacture this product or provides a manufacturers warranty or
support. www.polaroid.com
Loading...