Polaroid PLA-4255BD User Manual

20041126
42” High-Definition Plasma Monitor
PLA-4255BD
Operation Manual
1
Table of Contents
Plasma Display
Set-Top Box
LED Indicators
Remote Control Unit
Installing the plasma Monitor
Basic Operation
Using the Remote Control
Basic Adjustments:
Video Source
PC Source
6
9
12
13
14
15
16
17
20
Audio Source
PIP Source
TV Source
Parental Menu
Settings Menu
Specifications
Troubleshooting
23
25
26
29
32
36
38
2
Safety Precautions
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USE-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Warning
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
Caution
To prevent electric shock, match wide blade of plug to wide slot, fully insert. Refer to the
identification/rating label located on the back panel of your product for its proper operating
voltage.
Caution
Using video games or any external accessory with fixed images for extended periods of time can
cause them to be permanently imprinted on the picture tube (or projection TV picture tubes).
ALSO, some network/program logos, phone numbers, etc. may cause similar damage. This
damage is not covered by your warranty.
The lightning flask with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Cable TV Installer
This reminder is provided to call your attention to Article 820-40 of the National Electrical Code
(Section 54 of the Canadian Electrical Code, Part 1) which provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be connected to the grounding
system of the building as close to the point of cable entry as practical.
Customer Record
You will find the model number and chassis number of your TV on the back of your TV set.
Record these numbers in the spaces provided below. Refer to them whenever you call customer
service or your dealer regarding this product.
Model Number:_______________________
Chassis Number:______________________
3
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or third prong
is provided for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long
periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
15. Warning - This product should only be serviced by an authorized and
properly trained technician. Opening the cover or other attempts by the user to
service this product may result in serious injury or death from electrical shock,
and may increase the risk of fire.
4
FCC Statement of Compliance
Class B Computing Device Information to User
This equipment has been tested and found to comply with the limits for a Class B
Digital Device pursuant to part 15 of FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment receives interference while off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) lncrease the separation between the equipment and TV.
3) Connect the equipment into an outlet on a circuit different from that to
which the TV is connected.
4) Consult the dealer or an experienced radio/TV technician for help and
for additional suggestions.
The user may find the following booklet prepared by the Federal
Communications Commission helpful: "How to Identify and Resolve Radio - TV
Interference Problems". This booklet is available from the US Government
Printing Office. Washington, D.C. 20402, Stock No. 004-000-00345-4.
FCC Warning
The user is cautioned that changes or modifications not expressly approved by
the manufacturer could void the user's authority to operate the equipment.
NOTE: In order for an installation of the product to maintain compliance with the
limits for a Class B Device, shielded cables must be used.
5
Plasma Display
Front view
1 2 3
1. Status LED indicator
2. IR Receiver for remote control
3. Standby/on LED indicator
6
Right view
1
2
1. STANDBY/ON button
2. VOLUME +/- buttons
3. CHANNEL +/- buttons
4. INPUT button
3
4
7
Rear view
5 6
7 8
5. SYSTEM CABLE terminal (BLACK)
6. SYSTEM CABLE terminal (WHITE)
7. AC INLET terminal
8. POWER switch
8
Set-Top Box
Front view
9
10 11 12 13 14 15
9. Push here to open the access panel door
10. COMPUTER (PC) INPUT terminal (ANALOG RGB)
11. COMPUTER (PC) INPUT terminal (AUDIO)
12. VIDEO 3 INPUT terminal (S-VIDEO)
13. VIDEO 3 INPUT terminal (VIDEO)
14. VIDEO 3 INPUT terminal (AUDIO L)
15. VIDEO 3 INPUT terminal (AUDIO R)
9
Back Panel Connections
17 18 19 20 21 22 23 24 25 26 16
27 28 29 30 31 32 33 34 35 36 37 38 39 40 41
16 AC INLET
17 30 INPUT terminals (VIDEO)
18 20 25 31 32 INPUT terminals (AUDIO L)
19 21 26 32 34 INPUT terminals (AUDIO R)
22 35 INPUT COMPONENT VIDEO terminals (Y)
23 36 INPUT COMPONENT VIDEO terminals (Cb/Pb)
24 37 INPUT COMPONENT VIDEO terminals (Cr/Pr)
27 Antenna Cable
28 29 INPUT terminals (S-VIDEO)
38 DVI cable terminal
39 SERVICE terminal
40 SYSTEM CABLE terminal (WHITE)
41 SYSTEM CABLE terminal (BLACK)
10
LED Indicators
Plasma Display
LED indicator
STATUS
Condition Description
Off Off AC power off The AC power is off
Off Flash Standby to on Only lights when power
Off Red Standby The power LED lights up in red
Off Blue On The indicator on the Plasma
Red Blue Sleep Sleep mode is going to go off.
Flash Blue DVI connector
error
Flash Flash DFP connector
error
switches from standby to on.
to indicate standby mode
Display lights up blue to
indicate power-on.
The DVI connector on the
system cable is disconnected
to Plasma Display.
The DFP connector on the
System cable is disconnected
to Plasma Display.
11
Set-Top Box
LED indicator Condition Description
Off AC power off The AC power of Set-Top Box is off
Flash Standby to on Only lights when power switches from
standby to on.
Blue On The indicator on the Set-Top Box lights up
blue to indicate power-on.
Red Standby The power LED lights up in red to indicate
standby mode
Flash Error 1. The DVI connector on the system cable
is disconnected to Set-Top Box.
2. The DFP connector on the system cable
is disconnected to Set-Top Box.
3. Both DVI and DFP connectors on the
system cable are disconnected to
Set-Top Box.
12
Loading...
+ 27 hidden pages