Polaroid DVC-2000 User Manual

Safety Precautions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

RISQUE DE CHOC ELECTRIQUE NE

PAS OUVRIR

The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

AVIS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION: (VISIBLE) LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM.

WARNING: DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE, DUE TO THE HIGH RISK OF FIRE

OR ELECTRIC SHOCK, DO NOT OPEN THE CABINET; DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. ONLY QUALIFIED SERVICE PERSONNEL SHOULD ATTEMPT THIS.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, AND

FULLY INSERT.

ATTENTION: POUR EVITER LES CHOCS ELECTRIQUE, INTRODUIRE LA LAME LA PLUS LARGE DE LA

FICHE DANS LA BORNE CORRESPONDANTE DE LAPRISE ET POUSSER JUSQU' AU FOUD.

CAUTION: This VCR&DVD PLAYER employs a Laser System. To prevent direct exposure to the laser beam, do not try to open the enclosure.

Visible laser radiation when open and interlocks defeated.

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

DO NOT STARE INTO BEAM.

To ensure proper use of this product, please read this owner’s manual carefully and retain for future reference. Should the unit require maintenance, contact an authorized service location, or contact local dealer. Only qualified service personnel should remove the cover.

FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device. Pursuant to the part 15 of FCC Rules.

WARNING: Changes or modifications made to this equipment, not expressly approved by manufacturer or parties authorized by manufacturer

will void all the manufacture warranties.

CLASS 1

LASER PRODUCT

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates,uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions,may cause harmful interference to radio communication.However,there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:To assure continued compliance,(example-use only shielded interface cables when connecting to computer or

peripheral devices).Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

THE REGION CODE FOR THE UNIT IS 1.

Since it is very usual for DVD movies to be released at different times in different regions of the world, all players have region codes and discs can have an optional region code. If you load a disc of a different region code to your player, you will see

the region code notice on the screen. The disc will not play, and should be unloaded.

For Customer Use:

In spaces provided below, record the Model and Serial No. located on the rear panel of your combo player.

Model No. Serial No.

Retain this information for future reference.

DVC-2000

Important Safety Instructions

CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Please carefully study this manual and always keep it available. There are, however, some installation and operation precautions which you should be aware of.

1.Read Instructions - All the safety and operating instructions should be read before the product is operated.

2.Retain Instructions - The safety and operating instructions should be retained for future reference.

3.Heed Warnings - All warnings on the product and in the operating instructions should be adhered to.

4.Follow Instructions - All operating and use instructions should be followed.

5.Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dry

cloth for cleaning.

6.Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards.

7.Water and Moisture - Do not use this product near water - for example the apparatus shall not be exposed to dripping splashing

and that no objects fill with liquid such as vases, should be placed on the apparatus. “WARNING” To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture.

8.Accessories - Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

9.A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

10.Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11.Power Sources - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12.Grounding or Polarization - This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. Alternate Warnings - This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature, If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

13.Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

14.Protective Attachment Plug - The product is equipped with an attachment plug having overload protection. This is a safety feature. See Instruction Manual for replacement or resetting of protective device. If replacement of the plug is required, be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection as the original plug.

15.Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size or grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

16.Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

DVC-2000

Important Safety Instructions

17.Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or

power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

18.Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

19.Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

20.Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Warning: This unit should only be serviced by an authorized and properly trained technician. Opening the cover or other attempts by the user to service this unit may result in serious injury or death from electrical shock, and may increase the risk of fire.

21.Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under

the following conditions: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e. If the product has been dropped or damaged in any way, and f. When the product exhibits a distinct change in performance - this indicates a need for service.

22.Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

23.Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

24.Wall or Ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

25. Heat - The product should be situated away from heat sources such as radiators, heat registers, stoves or other products

(including amplifiers) that produce heat.

UNPACKING

First check and identify the contents of your Combo Player package, as listed below: VCR&DVD Player 1 AUDIO cable(red and white) 1 Video cable(yellow) 1 Batteries(AAA) 2 Remote control 1 RF(Radio Frenquency)Antenna Cable 1 User’s manual 1 If any item should be damaged or missing, please inform your dealer without delay. Keep the packaging materials, you may need them to transport your player in the future.

WHERE TO PALCE YOUR Combo Player

A. Place the unit on a firm, flat surface. B. When you place this combo player near a radio, or VCR, the playback picture may become poor and/or distorted. In this situation, move the Combo player away from the other units. C. If placed in a cabinet, please allow at least 2.5 cm (1 inch) of free space all around the player for proper ventilation.

TO OBTAIN A CLEAR PICTURE

The Combo Player is a precision device. If the optical pick-up lens, disc drive parts and head are dirty or worn down, picture quality can become poor. We recommend regular inspection and maintenance every 1,000 hours of use depending on the operating environment.

Note:

The OSD and illustration in this manual may be somewhat different from the actual situation. Please take the unit as the standard.

DVC-2000

Introduction

R E A D A B L E

Active

Your new VCR&DVD PLAYER is designed for you to enjoy all forms of disc media and VHS Tape. Your player will allow you to enjoy full-length motion pictures with “at-the-movies” picture and cinema quality sound. Your new player also supports CD, MP3, and WMA.Your player also has several unique features, including AFF (Active Full Screen Function that allows you to view wide screen movie presentations in full screen mode), SVideo and component video output (for greater picture clarity), Parental Control (to prevent children from viewing inappropriate content) and Kodak Picture CD compatibility (so you can view photos on your TV). This is a true multimedia machine designed for the multimedia world to enjoy.

Notes on Discs

HOW TO HANDLE, CLEAN, AND STORE DISCS.

HANDLING DISCS

• Do not touch the playback side of the disc.

• Do not attach paper or tape to discs.

CLEANING DISCS

• Fingerprints and dirt on the disc cause picture and sound deterioration. Wipe the disc from the center outward with a soft cloth. Always keep the disc clean.

• If you cannot wipe off the dirt off, wipe the disc lightly with a slightly moistened soft cloth and finish with a dry cloth.

• Do not use any type of solvent such as a thinner, benzine, commercially available cleaners or anti-static spray for vinyl LP’s.

PLAYABLE DISCS

This Combo Player can playback the following discs.

Disc Mark Contains Disc Size Maximum playback time

DVD video disc

Audio CD

MP3 CD

Audio

Video

(moving

pictures)

Audio

12 cm

8 cm

(CD single)

12 cm

Approx. 600+ minutes

Approx. 4 hours

(single sided disc)

Approx. 8 hours

(double sided disc)

Approx. 74 minutes

Approx. 20 minutes

STORING DISCS

• Do not store discs in places subject to direct sunlight or near heat sources.

• Do not store discs in places subject to moisture and dust.

• Store discs vertically in a case. Stacking or placing objects on discs outside of their case may cause warping.

NOTES ON REGIONAL NUMBERS

DVDs are divided into separate regions. The United States and Canada are designated as region 1 DVD. Your player plays region 1 DVDs only.

TYPE OF TV SYSTEM

Connect this Combo Player to a TV with the NTSC system.

Kodak Picture CD

WMA

Spec.

Audio

12 cm

Up to approx. 22 hours playback

DVC-2000

Table of Contents

Safety Precautions....................................................1

Important Safety Instructions.....................................2

Introduction...............................................................4

Notes On Discs..........................................................4

Identification of Controls............................................5

Remote Control.........................................................6

Connecting with TV....................................................8

Connecting Optional Equipment................................8

Connecting TV With S-VIDEO /Component Jack,

AMP With Digital Audio Out Jack...............................9

Progressive Scan......................................................9

VCR Playback.........................................................10

Recording................................................................10

Search Function......................................................11

VCR Setting.............................................................12

AFF Function...........................................................14

Playing Back a Disc.................................................14

Locating a Specific Title,

Identification of Controls

FRONT PANEL

Chapter or Track......................................................16

Using the On-screen Display...................................17

Playing Repeatedly..................................................18

Playing in Random Order........................................18

Zooming a Picture On DVD....................................18

Selecting The Camera Angle/

Language/Audio Settings........................................19

Selecting Subtitles ..................................................19

Playing in a Favorite order.......................................20

MP3 Operation........................................................20

WMA Operation.......................................................21

Playing Back Your Kodak Picture CD......................21

Playing Your JPEG Files..........................................22

Memo On Output Sounds........................................22

Setting the Parental Lock........................................23

Customizing the Function Settings..........................24

Troubleshooting Guide............................................25

Specifications..........................................................26

REAR PANEL

1 2 3 4 5 6 7 8 9 11 12 13

1 POWER 2 VIDEO INPUT JACK 3 AUDIO INPUT JACK 4 RECORD 5 TV/VCR 6 CHANNEL UP/DOWN BUTTON 7 VCR DECK 8 OPERATION DISPLAY WINDOW 9 EJECT 10 DVD TRAY 11 VCR INDICATOR 12 DVD INDICATOR 13 DVD/VCR 14 STOP 15 PLAY/PAUSE 16 SKIP REVERSE 17 SKIP FOIRWARD 18 OPEN/CLOSE

DVC-2000

141516

18 1 2 3 4 5 6 7 8

1 DIGITAL AUDIO-OPTICAL OUTPUT 2 S-VIDEO OUTPUT 3 DIGITAL AUDIO-COAXIAL OUTPUT 4 COMPONENT/PROGRESSIVE VIDEO

OUTPUT Y Pb Pr

5 ANALOG AUDIO OUTPUT L R 6 ANALOG AUDIO INPUT L R

7 ANALOG AUDIO OUTPUT L R 8 COMPOSITE VIDEO OUTPUT

9 COMPOSITE VIDEO INPUT 10 RF OUTPUT 11 ANTENNA INPUT

9 10 11

Remote Control

THE INSTRUCTIONS BELOW DESCRIBE THE FUNCTIONS ON THE REMOTE CONTROL.

18.

1. POWER

NUMBER BUTTONS

2. STEP

3. SUBTITLE

4. SHUFFLE

5. REPEAT

6. AUDIO

7. A-B REPEAT

8. DVD

9. VCR

10. SETUP

11. MENU

12. DIRECTION BUTTONS

19. OPEN/CLOSE

20. ANGLE

21. I/P (INTERLACE/PROGRESSIVE SCAN)

22. ZOOM

23. AFF

24. DISPLAY

25. REC

26. TITLE

27. ENTER

28. STOP

29. SKIP REVERSE

13. PLAY/PAUSE

14. FAST FORWARD

15. FAST REVERSE

16. PROGRAM

17. SEARCH

30. SKIP FORWARD

31. SPEED

32. TV/VCR

33. COUNTER/CLOCK

34. INPUT SEL.

35. CLEAR/RESET

• POWER button on the remote control is for standby power.

• When“ ” displayed on TV, function is not operational on the disc.

• Child Lock!!! Press the POWER button of the remote control for about 8 seconds. No buttons of front panel and remote control can be operated now and Lock indicator “ ” will be displayed on window display. To release child lock, press the POWER button of the remote control for about 8 seconds.

DVC-2000

Continued

Remote Control

PREPARING THE REMOTE CONTROL

To operate the Combo Player, you must first place the batteries in the remote control.

1 2 3

Open the cover.

Insert batteries (AAA size).

Make sure to match the + and - on the batteries to the marks inside the battery compartment.

OPERATING WITH THE REMOTE CONTROL

Operating player with the remote control.

The remote control must point at the remote sensor in order for the remote to function correctly.

Distance: Maximum of 7 m from the front of the remote sensor.

Angle: Approximately 30º from each direction.

*Do not place the remote control under intense light source such as direct sunlight.

Close the cover.

BATTERIES

INCORRECT USE OF BATTERIES MIGHT CAUSE THEM TO LEAK, CORRODE OR EXPLODE.

• Do not place the batteries in the wrong direction.

• It is dangerous to charge, heat, open, or short-circuit the batteries.

• Do not leave dead batteries or mix new with old batteries in the remote control.

• When not using the remote control for a long duration of time, remove the batteries.When operating range becomes reduced, replace batteries.

• If battery leakage occurs, wipe the battery liquid from the battery compartment, then replace batteries.

REMOTE CONTROL

• The remote control should be aimed directly towards the remote sensor of the Combo Player.

DVC-2000

Connecting With TV

• In connecting RF cable to TV, set TV channel to CH3.

How to Connect with RF cable or AV cable

1 Connect antenna cable to the “ANT.IN” jack on rear panel of player. 2 Connect TV to the Combo Player by connecting the “RF OUT” jack with “ANT.IN” jack of the TV with RF cable. 3 Connect AV OUT jack on VCR&DVD PLAYER to AV IN jack of the TV with RCA cables.

• Connect with Audio/Video terminal, you can enjoy more clean video and audio.

Connecting With Optional Equipment

How to Connect

1 Connect AV OUT jack on camcorder (or playback video) to AV IN jack on rear panel (or front panel) of VCR&DVD PLAYER with RCA cables.

DVC-2000

Connecting TV With S-VIDEO/Component Jack, AMP With Digital Audio Out jack

How to Connect(DVD only)

1 Connect S-VIDEO OUT or COMPONENT OUT to TV.

2.Connect analog AUDIO OUTPUT(L/R) jack to TV. 3 Connect COAXIAL or OPTICAL to AMP of Dolby Digital.

Progressive Scan

WHAT IS PROGRESSIVE SCAN?

With the introduction of Digital/High-Definition TV, televisions can scan viewable information at double the frequency of standard NTSC televisions. This provides for greater picture clarity and detail. This player provides the delivery of images to these newer televisions with greater detail and film like quality. Connect the player to your HDTV ready television using the component video inputs/outputs.

HOW TO SETUP THE VIDEO SCAN MODE?

Connect this Player with Y, Pr and Pb, if your TV has Progressive Scan and Component Video input. Press I/P button on remote control unit to switch between Interlace & Progressive Scan mode.

It is forbidden by law to copy, broadcast, show, play in public, and rent copyrighted material without permission.

DVD video discs are copy protected, and any recordings made from these discs will be distorted.

Manufactured under license from Dolby Labs.

“Dolby” and the double-D symbol are trademarks of Dolby Laboratories. Confidential unpublished works.

“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.

DVC-2000

VCR Playback

1 Press POWER button to power on.

Press VCR button to change into VCR mode.

2 Insert the desired tape.

3 If you want to playback it, press button.

When the playback picture is partially noisy, adjust with

TRACKING +/- button. 4 To stop it, press button.

• For pause, press button in playback mode.

Recording

To Record With VCR

1 Press POWER button to power on.

• Press VCR button to change into VCR mode.

• Power on TV and select Ch3, or select AV input. 2 Insert a tape for recording.

• Insert a tape with recording tab. 3 With CH+/- and NUMBER button, select the desired broadcasting channel or external input unit to record.

To Enjoy DVD during recording

If you want to playback DVD during recording with video, insert a DVD disc.

• Place the desired DVD disc on DVD tray, press DVD button

5 To playback forward fast or to reverse it, press o r button, respectively.

• Press EJECT button on the front panel or OPEN/CLOSE button on remote control to remove the tape.

4 Select the desired speed (SP or SLP) with SPEED button. 5 Press REC button.

6 press button to pause recording, press again to resume.

•If the pause status continues for five minutes, the recording will be cancelled automatically.

7 To stop recording, press button.

to switch into DVD mode and press button. Then, you can watch DVD.

To Copy From DVD To Videotape

Press DVD button to convert output into DVD mode. 1 Insert the desired DVD disc.

• you can’t copy a DVD disc with copy protect function. 2 Insert a tape for recording.

This product incorporates copyright protection technology that is protected by method claims of certain U.S patents and other intellectual property rights owned by Macrovision Corporation and other right owners Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

3 Press REC button. 4 To stop copy, press VCR button and then press button.

• If not, DVD plays again and video continues to copy.

DVC-2000

(continued)

Recording

One Touch timer Recording(OTR)

One-Touch Recording(OTR) allows you to record in 30-minute increments up to 4 hours at the touch of a button. 1 Start Recording

Follow the instructions on “Recording”. 2 Activate OTR While in Record mode, press the REC button again to activate One-Touch Recording(OTR). 3 Add Recording Time

Continue pressing REC to add recording time in 30 minute increments up to 4 hours.

•The VCR&DVD PLAYER stops recording automatically when the time has elapsed.

4 Press button to stop recording mode.

Search Function

Search Counter Zero

• Press VCR button to change into VCR mode. 1 Press the SETUP button on the remote control.

2. Press the button to select the “Search”, and press ENTER button.

3. Press ENTER button at “Go To Zero Search” to start.

Search Counter

•Press VCR button to change into VCR mode. 1 Press the SETUP button on the remote control.

2. Press the button to select the “Search”, and press ENTER button.

Search Index Forward/backward

• Press VCR button to change into VCR mode. 1 Press the SETUP button on the remote control.

2. Press the button to select the “Search”, and press ENTER button.

3. If your search is forward direction, highlight “Index Search(+)” Index searching motion, then press ENTER button.

• AS soon as the counter searches 0:00:00 , the tape will play automatically.

3. Press the button to select the “Counter Search”, and press ENTER button.

4. Enter the desired time and press ENTER button.

• The counter appears on screen and the LED.

4. If your search is backward direction, highlight “Index Search(-)” Index searching motion, then press ENTER button.

• The index signal is recorded on the tape automatically when the recording is started. You can view a recording at a specific start point.

Search Index Number

• Press VCR button to change into VCR mode 1 Press the SETUP button on the remote control.

2. Press the button to select the “Search”, and press ENTER button.

3. Press the button to select the “Index Number Search “, and press ENTER button.

DVC-2000

4. Index NUMBER setting method.

• If your search is forward direction, press up button to select desired Index Number.

• If your search is reverse direction, press down button to select desired Index Number.

5 After setting up , Please Press ENTER Button.

VCR Setting

Clock

• Press VCR button to change into VCR Mode and follow the procedures below.

1 Press the SETUP button on the remote control. 2 Press the ENTER button, while highlighting CLOCK SET.

3 Set the current date and time with button or

Program

1 In VCR mode press the SETUP button on the remote control . 2 Press the button to select the “Program Set” and press

ENTER button. 3 Select “Channel”

• move into desired channel signal with up /down button channel signal change like the orders below.

cable video 1 video 2 Antenna

4 Select “Start Date”

• Move into “Start Date “with button and then, select the

desired number to record with up/down button or number button 5 Select “REC cycle”.

• Move into “REC Cycle” with button and then, select the

desired one with up/down button

• REC cycle changes like the orders. One Time weekly weekdays Daily

NUMBER button. For DATE SET, follow the order of Month/Day/ Year ; for TIME SET, follow the order of Hour/Minute in CLOCK SET screen. 4 Press SETUP button after completed.

• Move into “Start Time” with button and then, select the desired number to record with up/down button or number button.

7 Select End time

• Move into "End Time" with button and then, select the desired number to record with Up/down button or number

button. 8 Select Tape Speed

• Move into "Tape Speed" with button and then, select the desired one with up/down button

• Recording speed changes like the orders below. SP SLP

• Press SETUP button to exit after completion.

• Press NEXT and PREV button to fisnish 8-event programming.

• Press the POWER button to activate timer recording.

6 Select Start Time

Channel

• Only operating in stop mode.

• Press VCR button to change into VCR mode and follow the procedure below.

1 Press the SETUP button on the remote control. 2 Press the button to highlight and select (Enter) the

“Channel Set”. 3 Selecting cable or antenna viewing

• You must set the viewing mode for your VCR, choosing either CABLE (cable system connection) or ANTENNA(antenna connection). To set the viewing mode:

• Press ENTER to toggle between CABLE and ANTENNA. 4 SELECT “Manual Set”

Move into “Manual set” with button to select one of add and erase with ENTER button. Memorize channel and select the desired channel when ENTER button is pressed, “Erase” converts into “Add”.

On-Screen Menu Language

1 Press the SETUP button on the remote control. The initial MENU is displayed.

2. Press the button to select the “Language Select” and

Press NUMBER button and / button of remote control to select the desired channel to memorize. To check the memorized channels, press CH+/- button on remote control. To delete Channels Manually, when ENTER button is pressed, “Add” converts into “Erase”. Press NUMBER

button and / button on the remote control to select the desired channel to delete. To check the deleted channels, press CH+/- button on remote control. 5 SELECT “Auto Preset”

• Press button in Channel Set to highlight “Auto Preset”

• Press ENTER button to detect the channel automatically.

press ENTER button 3 Select the language among English, Spainish and French.

DVC-2000

VCR Setting

Setting The OSD Display

• Press VCR button to change into VCR mode 1 Press the SETUP button on the remote control.

2. Press the button to highlight and select the “Option”, and press ENTER button.

Auto Power Off

3. Press ENTER button until the appropriate system is

selected.(“On” or “Off”)

4. Please press SETUP button to quit.

• Press VCR button to change into VCR mode 1 Press the SETUP button on the remote control.

2. Press the button to select the “Option”, and press ENTER button.

RF Out

• Press VCR button to change into VCR mode

1. Press the SETUP button on the remote control.

2. Press the button to select the “Option”, and press

ENTER button.

Tape Handling

1. Do not use any tape below. Damage of video head or cut/coiling of tape may cause failure.

-Tape with mold

-Tape stained with juice or attachments

-Tape having breakage connection

-Disassembled tape

2. Moisture condensation may occur in tape. Moisture condensation damages the tape. Please use the tape after the

3. Press the button to select the “Auto Power Off”.

4. Press ENTER button, until the appropriate system is

selected.(“Yes” or “No”)

5. Press SETUP button to quit.

3. Press the button to select the “Output Channel”.

4. Press ENTER button, until the appropriate system is

selected. ( “CH3” or “CH4” )

5. Press SETUP button to quit.

moisture condensation is disappeared.

3. After use, store tape vertically in a case to prevent loose.

4. Do not store in the following places.

-High temperature and humidity

-Subject generation of mold

-Subject to direct sunlight

-Much dirt or dust

-Near strong magnetic materials such as speaker

DVC-2000

AFF Function

WHAT IS AFF?

AFF stands for Active Full-screen Function. It allows you to fill the television screen viewing area when using a wide screen formatted DVD. Press the AFF button on your remote control,this will eliminate black bars on the top & bottom of the TV screen when viewing movies with an aspect ratio of 1.85:1 and minimize (but not eliminate) black bars on movies with a wider aspect ratio (2.35:1).

Before AFF

After AFF

Playing Back a Disc

HOW TO PLAYBACK A DISC.

Basic Playback

How to playback DVD video discs.

• Turn on the TV and select the video input source which is connected to the Combo Player.

1. Press the POWER button on the front panel. Press DVD button of remote control to change into DVD mode.

2. Press the OPEN/CLOSE button.

This will open the disc tray.

3. Place the disc on the disc tray.

Be sure the playback side is faced down.

4. Press the button.

After closing the disc tray, playback will start.

• A disc may be damaged if not correctly placed on the guides in the disc tray. This may also cause the Combo Player to malfunction.

• The menu screen will appear automatically or you may access the menu screen by pressing the TITLE button.

• Moving the Combo Player during playback may cause damage to the disc as well as the player.

• To open and close the disc tray, you should only use the OPEN/CLOSE button on the remote control or Combo Player.

DVC-2000

Continued

Playing Back a Disc

FOR A HIGHER QUALITY PICTURE

The DVD discs produce a high resolution picture with abundance of information. This may cause some picture noise on the TV during playback. The noise will vary depending on the TV used with the Combo Player. To control picture noise reduce the sharpness adjustment on your TV when viewing DVD discs.

ABOUT DVD, CD

DVD, CD icons will appear depending on the disc being played back.

DVD: DVD video discs CD: Audio CDs

HOW TO START PLAYBACK FROM THE MENU SCREEN

1. Press or the number buttons to select the title.

2. Press the ENTER button.

The Combo Player will start playback from the title selected.

Title 1

Title 3

Title 2

Title 4

HOW TO PAUSE PLAYBACK (STILL PLAYBACK)

Press the during playback. Press the button to resume normal

playback.

HOW TO REMOVE THE DISC

Press the OPEN/CLOSE button.

Wait until the disc tray is completely open before removing any discs. After removing the discs, press the OPEN/CLOSE button to close the disc tray.

HOW TO STOP PLAYBACK

Press the STOP button once.

The Combo Player is stopped.

Press the button to replay. Press the STOP button twice. The Combo Player is stopped completely.

At the completion of each movie a menu screen will appear. Be aware that the on-screen setup menu may damage your TV by

permanently burning that image onto the screen. To avoid this, press the STOP button at the completion of each movie. You may also decide to setup the SCREEN SAVER.

ADVANCED PLAYBACK

The Combo Player allows you to playback discs at various speeds.

TV SCREEN

2x 4x 8x 16x

8x4x

16x

PLAYING AT 2X, 4X, 8X, OR 16X THE NORMAL SPEED

You can play back a disc at 2x, 4x, 8x, or 16x the normal speed.

Press the REW or FF button during playback.

The playback speed becomes 2x the normal speed. The playback speed changes each time you press the REW or FF button. REW: Fast reverse FF: Fast forward

Press to resume normal playback.

THE DVD VIDEO DISCS ARE NORMALLY DIVIDED INTO TITLES. THE TITLES ARE SUB-DIVIDED INTO CHAPTERS. MOREOVER, AUDIO CD AND MP3 CD ARE DIVIDED INTO TRACKS. YOU CAN CONVENIENTLY LOCATE ANY SPECIFIC TITLE, CHAPTER, OR TRACK WITH THIS COMBO PLAYER.

• The Combo Player may not playback sound during scan reverse or forward playback of DVD video discs. The Combo Player will play sound during fast forward or fast reverse playback of audio CDs.

• The speeds may vary slightly from disc to disc and the 2x, 4x, 8x, and 16x speeds are only approximate speeds.

DVC-2000

Continued

Playing Back a Disc

PLAYING IN SLOW-MOTION

A disc can be played back in slow-motion.

Press the or button during pause.

Press button to resume normal playback.

NOTICE

• During the slow-motion playback, the sound may not be heard.

• Some discs do not utilize this feature.

RESUMING PLAYBACK FROM THE SAME LOCATION

This Combo Player allows you to stop playback and continue playback later from the same location on the disc.

1. Press the STOP button

This will interrupt the playback and the Combo Player will memorizes the location where you stopped playback.

2. Press the button

The Combo Player will resume the playback from the location where you stopped playback.

NOTICE

• The following action will cancel the RESUME function:

- Powering off the Combo Player after you stop playback.

- Ejecting the disc.

• Depending on the disc, you may experience a difference of location where playback resumes.

• Some discs do not utilize this feature.

Locating a Specific Title, Chapter or Track

Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3 Track 1 Track 2 Track 3 Track 4 Track 5

TITLE 1

DVD Video Disc

LOCATING A TITLE USING THE TITLE MENU

You can locate a specific title using the title menu function, if a DVD video disc contains a title menu.

1. Press the TITLE button

On the TV screen, the title menu will appear.

2. Press the button to select the title you want

You can also directly locate a specific title by pressing its assigned number

with the number buttons.

3. Press the ENTER button

This will cause the Combo Player to start playback from chapter 1 of the title selected.

TITLE 2

Audio CD

NOTICE

• You may find that some discs will not respond to this function.

• If different instructions appear on the TV screen, follow those instructions. The instructions above are describing the basic procedure. Procedures may vary depending on the contents of the DVD video disc.

DVC-2000

Continued

Locating a Specific Title, Chapter or Track

LOCATING A SPECIFIC CHAPTER OR TRACK

This Combo Player allows you to locate consecutive chapters or tracks.

Press the SKIP or button repeatedly to display the requested chapter or track

The Combo Player starts playback from the selected chapter or track.

How to locate preceding chapters or tracks

• When you press the SKIP button, the Combo Player starts playback from the beginning of the preceding chapter or

track.

How to locate succeeding chapters or tracks

• When you press the SKIP button, the Combo Player starts playback from the beginning of the succeeding chapter or track.

On some discs the titles may not display the sub-divided chapters.

LOCATING A TITLE

You also can locate a specific title by directly selecting a title number.

1. Press SEARCH button during playback.

The menu will appear.

2. Press direction buttons and numbers to select the title and chapter you want.

3. Move the cursor to select Audio, Subtitle, Angle, TT Time, CH Time, Repeat, Time Disp..

NOTICE

• The displays may vary depending on the discs.

• You may experience a difference in TITLE or MENU display.

Using the On-Screen Display

THE COMBO PLAYER ALLOWS YOU TO VIEW THE OPERATIONAL STATUS AND DISC INFORMATION ON YOUR TV SCREEN.

CHECKING THE OPERATIONAL STATUS

With this function you can view on your TV the following:

-Current title

-Track number

-Total playing time

TO TURN OFF THE ON-SCREEN

DISPLAY

Press DISPLAY repeatedly until

DISPLAY OFF appears on TV screen.

Press DISPLAY during playback

Current Title

Title Elapsed

TT 01/12 CH 06/39 0:02:20

Title Remain

TT 01/12 CH 06/39 0:18:50

Chapter Elapsed

TT 01/12 CH 06/39 0:03:50

Chapter Remain

TT 01/12 CH 06/39 0:10:40

Current Chapter

Total Chapter Total Title

DVC-2000

Display Off

Playing Repeatedly

THIS Combo Player ALLOWS YOU TO PLAYBACK A SPECIFIC TITLE, CHAPTER, TRACK, OR SEGMENT REPEATEDLY. (TITLE REPEAT, CHAPTER/TRACK REPEAT, A-B REPEAT).

HOW TO REPEAT A TITLE, CHAPTER, OR TRACK

1. Select the title, chapter, or track you want to repeat.

2. Press the REPEAT button.

The repeat mode changes each time you press the REPEAT button.

Chapter

Title

All

Repeats the same chapter.

Repeats the same title.

Repeats the disc.

HOW TO REPEAT A SPECIFIC SEGMENT

1. Press the A-B RPT button at the beginning of the segment in which you want to repeat playback. (point A)

2. Press the A-B RPT button again at the end of the segment (point B).

The Combo Player will automatically return to point A and start to repeat playback of the selected segment (A-B).

3. Press the A-B RPT button to cancel the A-B repeat function.

No repeats.

DVD video disc

• Depending on the disc, you may experience a difference between point A and the location where playback actually resumes.

• Be aware that some discs will not respond to the A-B repeat function.

The Combo Player will resume to normal playback.

Playing in Random Order

THIS COMBO PLAYER ALLOWS YOU TO PLAYBACK TITLES, CHAPTERS WITHIN A TITLE, OR TRACKS IN RANDOM ORDER. (RANDOM PLAYBACK)

PLAYING TITLES IN RANDOM ORDER

This Combo Player will automatically choose the titles in a DVD video disc and play them back randomly.

1. Press the SHUFFLE button .

The Combo Player will now start random playback.

2. TO RESUME NORMAL PLAYBACK.

Press the SHUFFLE button again during random playback.

• The Combo Player will go to another chapter or track and start playback if you press the SKIP button during random playback.

Zooming a Picture On DVD

ZOOMING A PICTURE

This Combo Player allows you to zoom into a picture as well as shift the zoom point.

2x 3x 4x

Press ZOOM during playback.

1/2

The Combo Player magnifiles in the center of the picture.

If you press during zoom playback, the zoom point shift.

1/3 1/4

TO RESUME NORMAL PLAYBACK.

Press ZOOM repeatedly during zoom playback,till the player resumes normal playback.

DVC-2000

Selecting The Camera Angles/ Language / Audio Settings

THIS COMBO PLAYER ALLOWS YOU TO SELECT FROM SEVERAL DIFFERENT ANGLES AND LANGUAGES.

HOW TO CHANGE THE CAMERA ANGLE

Press the ANGLE button while playing back a scene recorded with multiple angles.

Each time you press the ANGLE button, the angle will change.

NOTICE

• The angle function will not work on DVD video discs that do not contain recorded multiple angles.

• The angle icon indicator will illuminate while playing back a title that contains at least one scene recorded with multiple angles.

HOW TO SELECT A PLAYBACK AUDIO SETTING

This Combo Player allows you to select a preferred language and sound recording system from those included on the DVD video disc.

ANGLE 1 ANGLE 2

Selecting the camera angle

1/2

2/2

1. Press the AUDIO button during playback.

Audio 1/3 : AC3 5.1CH English

Language

Total Audio Channels

Current Audio Position

2. Press the AUDIO button again to cycle backwards.

Audio 2/3 : AC3 5.1CH French

Audio 3/3 : AC3 5.1CH Spanish

Audio 1/3 : AC3 5.1CH English

Good evening Bonsoir Buenas tardes

Selecting a language

NOTICE

• The player returns to the initial default settings, when you turn on the Combo Player or replace a disc.

Selecting Subtitles

THIS COMBO PLAYER ALLOWS YOU TO DISPLAY THE SUBTITLES FROM THOSE INCLUDED ON THE DISC, ON TO YOUR TV SCREEN.

HOW TO DISPLAY SUBTITLES

You have the option to select a preferred subtitle from those included on the DVD video disc.

Press the SUB-T button during playback.

Subtitle

Subtitle Off

01/02 : English

02/02 : French

To TURN OFF the subtitles.

Press the SUB-T during playback

until SUBTITLE OFF appears.

Subtitle Off

NOTICE

• With some DVDs, you may not be able to turn off the subtitles and they will appear on screen automatically.

• As you press the SUB-T button, the subtitles may not appear immediately during some scenes.

• If the subtitles continue to show on your TV even after the DVD has been turned off, please refer to the TV’s close caption settings.

DVC-2000

Playing in a Favorite Order

COMBINE YOUR FAVORITE TITLES, CHAPTERS, OR TRACKS AND PLAY THEM BACK IN ANY ORDER.(PROGRAM PLAYBACK)

HOW TO SET TITLES, CHAPTERS, OR TRACKS IN A FAVORITE ORDER

The program playback function will automatically playback titles, chapters or tracks in the order preprogrammed.

1. Insert a disc, then press the PROGRAM button.

At this time, the menu will appear.

Program: TT(XX) CH(XX) 01 TT: CH: 06 TT: CH: 02 TT: CH: 07 TT: CH: 03 TT: CH: 08 TT: CH: 04 TT: CH: 09 TT: CH: 05 TT: CH: 10 TT: CH:

Exit NEXT

2. Using the numbered button, select the items in the order you want them programmed in.

Program: TT(XX) CH(XX) 01 TT:05 CH:12 06 TT: CH: 02 TT:02 CH:07 07 TT: CH: 03 TT:04 CH:07 08 TT: CH: 04 TT: CH: 09 TT: CH: 05 TT: CH: 10 TT: CH:

Exit Start NEXT

3. Select the START from the menu, then press the ENTER button.

The Combo Player starts memory playback.

To CHANGE the programmed item:

Press the STOP button, then follow step 1.

To CANCEL the programmed item:

Press the STOP button, then press the

button.

• When the Combo Player is turned off, or if the disc is removed, the program item will be removed.

• Depending on the disc, the program playback may not function.

To clear the numbers that you have programmed in just now, press CLEAR button.

MP3 Operation

WHAT IS MP3?

MP3 refers to a format of music files available for playback over the internet because of the popularity to download music from MP3 websites on to ones computer.

PLAYING A MP3 FORMAT

1. To pIay you must view through your television. Insert a MP3 CD, the Combo Player will initialize the disc when the tray is closed and the directory (folder) will be shown in a MP3 MENU on screen.

2. Press then the key to select and highlight a MP3 file (song). Press ENTER to play.

DVC-2000

WMA Operation

WHAT IS WMA?

WMA refers to a new format of music files from Microsoft available for playback from WMA web sites. The compression used allows you to record from your computer up to 22 hours of music on CD-R and play back through your combo player.

PLAYING A WMA FORMAT

1.To pIay you must view through your television. Insert a WMA CD, the

Combo Player will initialize the disc when the tray is closed and the directory (folder) will be shown in a WMA MENU on screen.

2.Then press then the key to select and highlight a WMA file

(song).

Press ENTER to play.

Playing Back Your Kodak Picture CD

NORMAL

When a Kodak Picture CD is inserted, an automated slideshow is launched, each picture in the current directory will be displayed consecutively in a slideshow fashion and will be scaled to fit most of the TV screen. Fifteen slideshow transition modes are provided. Use “PROGRAM” key to select: Customers can set “transition” effects for every

picture at any time during the slideshow.

NONE:(by default) mode 1: WIPE TOP mode 2: WIPE BOTTOM mode 3: WIPE LEFT mode 4: WIPE RIGHT mode 5: DIAGONAL WIPE LEFT TOP mode 6: DIAGONAL WIPE RIGHT TOP mode 7: DIAGONAL WIPE LEFT BOTTOM mode 8: DIAGONAL WIPE RIGHT BOTTOM

To display an image indefinitely, press the key. To view the Next or Previous picture press the SKIP FORWARD or SKIP REVERSE key. To resume the slideshow press the key.

mode 9: EXTEND FROM CENTER H mode 10: EXTEND FROM CENTER V mode 11: COMPRESS TO CENTER H mode 12: COMPRESS TO CENTER V mode 13: WINDOW H mode 14: WINDOW V mode 15: WIPE FROM EDGE TO CENTER RANDOM

IMAGE ROTATION

There are four modes to rotate a picture: “Invert”, “Mirror”, “Left”, and “Right”. These operations are allowed only when a picture is being displayed normally, and will be cancelled automatically when a new picture is displayed. The direction buttons are used to select the different transformation modes: Up -Invert/Normal Left -Turn left Down -Mirror/Normal Right -Turn right

REPEATING THE SLIDESHOW

At the end of your picture slideshow, each image is reduced to a “thumbnail” sized display.

Important: Let the player complete it’s layout of twelve pictures before pressing SKIP FORWARD button again to

view the next twelve.

The MENU key is used to display thumbnail pictures from the stop position. After it is enabled, up to twelve scaleddown thumbnail pictures will be display on the screen. The SKIP FORWARD/REVERSE keys can be used to display the NEXT and PREVIOUS twelve pictures in the current directory.

DVC-2000

Playing With Your JPEG Files

R E A D A B L E

PLAYING YOUR JPEG FILES

Normal Slide Show Presentation

When a JPEG disc is loaded into the player, a menu will appear on screen. Each picture in the current directory will be displayed consecutively in a slideshow presentation and will be seated to the most of your TV screen. Fifteen slideshow “transition” modes are provided. Use PROGRAM key to select.

mode 9: EXTEND FROM CENTER H mode 10: EXTEND FROM CENTER V mode 11: COMPRESS TO CENTER H mode 12: COMPRESS TO CENTER V mode 13: WINDOW H mode 14: WINDOW V mode 15: WIPE FROM EDGE TO CENTER RANDOM

IMAGE ROTATION

There are four modes to rotate a picture: Invert, Mirror, Left, and Right. These operations are allowed only when a picture is being displayed normally, and will be cancelled automatically when a new picture is displayed. The direction buttons are used to select the different rotation modes: Up -Invert/Normal Left -Turn left Down -Mirror/Normal Right -Turn right

ZOOM

This features allows you to view a picture at 50%-200% in several increments. Press the ZOOM button. An on screen message (“Zoom 100%”) will verify your selection. Use and keys to control the zoom level. Press the direction

keys to move the picture in any direction. . Note: When in the ZOOM mode, the slideshow transition and image transformation features are disabled.

Memo On Output Sounds

DISCS AND OUTPUT SOUNDS

DVD Video Discs CD MP3 CD

Sound recording

system

Audio setting on

the setting screen

ANALOG

AUDIO OUT jacks

DIGITAL

AUDIO OUT jack

SPDIF

/RAW

___

Dolby Digital

bitstream

Dolby Digital

SPDIF

/PCM

___

PCM

(48kHz)

ANALOG

SPDIF

/RAW

___

MPEG 2

bitstream

MPEG 2

SPDIF

/PCM

___

PCM

(48kHz)

ANALOG

SPDIF

/RAW

SPDIF

/PCM

___

PCM

(48kHz)

Linear PCM

48kHz 96kHz

ANALOG

SPDIF

/RAW

PCM

(48kHz)

SPDIF

/PCM

___

ANALOG

___

PCM44.1kHz

SPDIF

/RAW

SPDIF

/PCM

___

PCM

(44.1kHz)

ANALOG

___

SPDIF

/RAW

SPDIF

/PCM

___

PCM

(44.1kHz)

MPEG 1 AUDIO LAYER 3 DISC (MP3)

MP3 Audio Disc Play Back Capable MP3 audio disc can be played back by operating the unit in the

same way as the audio CD.

DVC-2000

MP3

ANALOG

___

Setting the Parental Lock

YOU CAN USE THE PARENTAL LOCK FUNCTION ONLY WITH DVD VIDEO DISCS EQUIPPED WITH THE PARENTAL LOCK FEATURE.

SETTING THE PARENTAL LOCK

DVD video discs equipped with the parental lock function are rated according to their content. The contents allowed by a parental lock level and the way a DVD video disc can be controlled may vary from disc to disc. For example, if the disc allows, you can edit out violent scenes unsuitable for children and replace them with more suitable scenes, or lock out playback of the disc all together.

1. Press STOP twice during playback.

2. Press SETUP

The SETUP MENU appears on the TV screen.

TO CHANGE YOUR PASSWORD:

1. Follow step 3 to select password, select Change.

2. Enter old password.

3. Enter new password.

4. Re-enter to confirm your new password.

5. Press ENTER.

6. Press SETUP.

3. Select Preference Page, press ENTER.

4. Select PARENTAL, press direction buttons.Select Parental, press ENTER.

5. Enter your password then press ENTER.

The preset password is

3308

DVC-2000

Customizing the Function Settings

THIS COMBO PLAYER ALLOWS YOU TO CUSTOMIZE THE PERFORMANCE TO YOUR PERSONAL PREFERENCE.

DISPLAYING THE SETUP MENU SCREEN

The SETUP MENU screen asks you to select a setting category from General Setup, Speaker Setup, Dolby Digital Setup, Video Setup and Preferences. The selected category will provide you the setting details on-screen.

1. Press SETUP.

2. Press to select category (highlight), then press ENTER.

3. Press SETUP to normal playback.

--General Setup Page-TV Display PS Angle Mark On OSD Lang ENG SPDIF Output RAW Captions Off Screen Saver On

Normal /PS* Normal /LB Wide

On* Off

English*

French Spanish

SPDIF Off SPDIF/RAW* SPDIF/PCM

On Off*

On* Off

--Speaker Setup Page-Downmix

LT/RT Stereo*

--Dolby Digital Setup-Dual Mono Dynamic

Stereo* L-Mono R-Mono Mix-Mono

FULL

3 / 4

1 / 2

1 / 4

OFF

-20 0 +20

--Video Setup Page-Sharpness Low Brightness 00 Contrast 00

High Medium Low*

-16 0 +16

--Preference Page-Audio ENG Subtitle Off Disc Menu ENG Parental Password Default

English* French Spanish Chinese Japanese Korean Russian Thai

Old Password New Password Confirm PWD

English French Spanish Chinese Japanese Korean Russian Thai Off*

1 KID SAFE 2 G 3 PG 4 PG-13 5 PG R 6 R 7 NC-17 8 ADULT*

Off

Change

Reset

NOTICE

• Preset password is 3308 .

•The SETUP MENU screen disappears if you press the SETUP button while it is displayed.

•Any button can disable Screen Saver except the POWER button. After that,you can press some button to make the relative operation.

• Functions and menu are subject to change without notice.

• You must remove any/all disc from the player in order to access Preference Page.

* Factory defaults

DVC-2000

+ 58 hidden pages

Polaroid DVC-2000 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual