Polaris RZR Pro R (2022) Owner's Manual

Download

2022

For Maintenance and Safety

OWNER’S MANUAL

RZR Pro R

WARNING

Operating, servicing, and maintaining a passenger vehicle or off-road

vehicle can expose you to chemicals including engine exhaust, carbon

monoxide, phthalates, and lead, which are known to the State of California

to cause cancer and birth defects or other reproductive harm. To minimize

exposure, avoid breathing exhaust, do not idle the engine except as

necessary, service your vehicle in a well-ventilated area and wear gloves

or wash your hands frequently when servicing your vehicle.

For more information go to www.P65Warnings.ca.gov/passenger-vehicle.

For videos and more information

about a safe riding experience with

your Polaris vehicle, scan this QR

code® with your smartphone.

Owner’s Manual

RZR Pro R

Unless noted, trademarks are the property of Polaris Industries Inc.

Recreational Off-Highway Vehicle Association® and ROHVA® are registered trademarks of the Recreational Off-Highway Vehicle Association. Tread Lightly® is a registered trademark of the United States Department of Agriculture. BatteryMINDer® is a registered trademark of VDC Electronics Inc. Loctite® is a registered trademark of Henkel Corporation. NYOGEL® is a registered trademark of Nye Lubricants, Inc. WD-40® is registered to WD-40 Manufacturing Company. QR Code® is a registered trademark of DENSO WAVE INCORPORATED. Sandisk® is a registered trademark of SANDISK LLC. Google Play® is a registered trademark of Google, Inc. Apple® and App Store® are registered trademarks of Apple Inc. NGK® is a registered trademark of NGK Spark Plug Co., Ltd. FOX® is a registered trademark of Fox Factory Inc. Bluetooth® is a registered trademark of Bluetooth Sig, Inc. ANSI® is a registered trademark of American National Standards Institute. WALKER EVANS RACING® is a registered trademark of Walker Evans Enterprises Incorporated. exFAT® is a registered trademark of Microsoft Corporation. Sachs® is a registered trademark of ZF Friedrichshafen AG.

Copyright 2021 Polaris Industries Inc. All information contained within this publication is based on the latest product information at the time of publication. Due to constant improvements in the design and quality of production components, some minor discrepancies may result between the actual vehicle and the information presented in this publication. Depictions and/or procedures in this publication are intended for reference use only. No liability can be accepted for omissions or inaccuracies. Any reprinting or reuse of the depictions and/or procedures contained within, whether whole or in part, is expressly prohibited.

The original instructions for this vehicle are in English. Other languages are provided as translations of the original instructions.

Printed in U.S.A.

9931527 REV 01

WELCOME

Thank you for purchasing a POLARIS vehicle, and welcome to our world-wide family of POLARIS enthusiasts. Be sure to visit us online at www.polaris.com for the latest news, new product introductions, upcoming events, career opportunities and more.

Here at POLARIS we proudly produce an exciting line of utility and recreational products. We believe POLARIS sets a standard of excellence for all utility and recreational vehicles manufactured in the world today. Many years of experience have gone into the engineering, design, and development of your POLARIS vehicle.

For safe and enjoyable operation of your vehicle, be sure to follow the instructions and recommendations in this owner’s manual. Your manual contains instructions for minor maintenance, but information about major repairs is outlined in the POLARIS Service Manual and can be performed by a factory certified Master Service Dealer (MSD) technician.

Your POLARIS dealer knows your vehicle best and is interested in your total satisfaction. Your POLARIS dealership can perform all of your service needs during and after the warranty period.

For the most up-to-date owner’s manual visit https://www. polaris. com/en-us/

owners-manuals

SAFETY SYMBOLS AND SIGNAL WORDS

The following signal words and symbols appear throughout this manual and on your vehicle. Your safety is involved when these words and symbols are used. Become familiar with their meanings before reading the manual.

DANGER

DANGER indicates a hazardous situation which, if not avoided, WILL result in

death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, COULD result

in death or serious injury.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, COULD result

in minor to moderate injury.

NOTICE

NOTICE provides key information by clarifying instructions.

IMPORTANT

IMPORTANT provides key reminders during disassembly, assembly, and

inspection of components.

ICON DESCRIPTION

The Prohibition Safety Sign indicates an action NOT to take in order to avoid a hazard.

The Mandatory Action Sign indicates an action that NEEDS to be taken to avoid a hazard.

TABLE OF CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . 7

Safety . . . . . . . . . . . . . . . . . . . . . . . 9

Features and Controls . . . . . . . . . . . . . . 27

Ride Command Display (if equipped) . . . . . . . 65

Operation . . . . . . . . . . . . . . . . . . . . 77

Emission Control Systems . . . . . . . . . . . . . 81

Maintenance . . . . . . . . . . . . . . . . . . 83

Specifications . . . . . . . . . . . . . . . . . . 149

Polaris Products . . . . . . . . . . . . . . . . . 151

Troubleshooting . . . . . . . . . . . . . . . . . 153

Warranty . . . . . . . . . . . . . . . . . . . . 177

Maintenance Log . . . . . . . . . . . . . . . . 187

INTRODUCTION

TOOLS FOR SAFE RIDING

To safely operate this vehicle, it is important to become familiar with its features, controls, and characteristics. Review the Safety Briefings for this vehicle that apply to you:

• Operators

• Riders

• Owners

• Trailering the Vehicle

• Maintaining the Vehicle

Additionally, read the product safety labels on the vehicle and follow all rules and regulations concerning the operation of this vehicle in your area.

POLARIS recommends anyone who will be operating this vehicle to take a training course. ROHVA® (Recreational Off-Highway Vehicle Association®) provides both an online safety e-course and a hands-on safety course. To access this training, visit www.rohva.org.

Other sources of safety information include the POLARIS Safety Video. The POLARIS Help Center also has additional information: https://RZR.polaris.com/ en-us/self-help

VEHICLE TESTING

This Off-Road Vehicle was subjected to the following tests of the National Standard for Recreational Off-Highway Vehicles, ANSI/ROHVA 1-2016:

• Maximum Speed Capability

• Service Brake Performance

• Parking Brake/Mechanism Performance

• Lateral Stability

• Pitch Stability

• Vehicle Handling

• Roll Over Protective Structure (ROPS)

• Occupant Retention System (ORS)

• Sound Level Limits

INTRODUCTION

VEHICLE IDENTIFICATION NUMBERS

Record your vehicle’s identification number q and engine serial number w in the spaces provided. Remove the spare key and store it in a safe place. The ignition switch must be replaced if all keys are lost.

Vehicle Model Number:

Vehicle Identification Number:

Engine Serial Number:

Personal PIN Security Code:

SAFETY

OWNER REQUIREMENTS

Improper use, maintenance, or modification of this vehicle can lead to serious injury or death.

Require proper use of your vehicle. Do not allow

anyone to operate your vehicle or ride as a passenger unless they are properly instructed and you are sure they are willing to ride responsibly. To prevent unauthorized use, always remove the ignition key when the vehicle is not in use.

Any modifications or installation of non-POLARIS-approved accessories could increase the risk of injury. While you may find aftermarket products

similar in design and quality to POLARIS accessories, recognize that some aftermarket accessories or modifications are not suitable because of potential safety hazards to you or others. It is never appropriate to install any additional seating.

Check with the manufacturer to determine any potential effect of a modification or accessory on the safe use of your vehicle. You are responsible for injuries related to modifications to the vehicle. Modifications or accessories may:

• Damage machine components - especially modifications that increase speed or power.

• Make the vehicle less stable at higher speeds.

• Add weight, reducing the amount of cargo and total weight you can carry, and raise the vehicle’s center of gravity.

• Overload the vehicle’s electrical system capacity (see page 149). Blowing a fuse may cause a loss of lights or engine power.

• Reduce the effectiveness of occupant protection systems, including the seatbelts and the Rollover Protective Structure (ROPS).

• Make it illegal to own or operate your vehicle. POLARIS-authorized spark arresters, mufflers, and emissions control components are mandatory for ownership or operation in many areas.

• Void your warranty.

The vehicle ROPS, when used with the seat belts and doors, provides a structure to help protect occupants. The structure will not protect occupants

in all rollovers or accidents.

SAFETY

DRIVER AND PASSENGER QUALIFICATIONS

Make sure operators are 16 or older with a valid driver’s license. Just because a teenager has a

license does not mean that they will make good judgments about driving and avoid risk taking.

POLARIS recommends that you supervise younger drivers. Set rules and put limits on how, when, and where they are allowed to use this vehicle. For example, young drivers may need to have an adult in the vehicle with them and not be allowed to drive with their friends in the vehicle.

Make sure all riders fit the vehicle. Be sure that the driver and all passengers are able to:

• sit with their backs against their seat,

• adjust the seat belt to fit properly,

• have both feet flat on the floor, and

• have both hands on the steering wheel or on a passenger hand hold.

Do not allow children who need child safety seats or booster seats to ride in the vehicle. The vehicle is not designed to restrain automotive child safety

seats.

You are responsible for your passengers. Be sure passengers are seated properly, belted, holding the passenger hand hold, and ready to brace. Unrestrained riders can fall out or be thrown around and from a moving vehicle.

Every person must be properly seated and belted in their own seat. Two people should never be belted into a single seat belt. People belted together can crash into one another in a collision and be seriously injured. Never carry passengers in the cargo bed as they could be thrown against or out of the vehicle or come into contact with moving parts.

Do not let people drive or ride after using alcohol or drugs.

PREPARE VEHICLE FOR THE RIDE

Before starting off, always perform the Pre-Ride Inspection. Failure to inspect and verify that the vehicle is

in safe operating condition increases the risk of an accident, which can lead to serious injury or death.

ITEM REMARK REFERENCE

SAFETY

Brake Fluid Ensure proper level and

condition

Front and rear suspension

Steering Ensure free operation page 131

Tires Inspect condition and

Wheels/Lug Nuts Inspect, ensure

Fuel and oil Ensure proper levels

Coolant Ensure proper level and

Indicator lights/switches Ensure proper

Inspect, lubricate if necessary

pressure

fastener tightness

and condition

condition

operation

page 120

page 90

page 25 page 126

page 127

page 92

page 108

page 30 page 54

Air Filter Inspect, replace as

needed

Engine intake pre-filter Inspect, clean page 115

PVT intake pre-filter Inspect, clean page 111

Headlights Check operation

Brake lights/taillights Check operation

Seat Latches Push down on both seat

backs to ensure the latches are secure

page 116

page 38

–

SAFETY

ITEM REMARK REFERENCE

Seat Belts Check length of belt for

damage, check latches for proper operation

Exhaust Inspect spark arrester

and clean if needed.

Vehicle Debris Remove grass, leaves,

and other flammable material or debris, especially near the exhaust system.

Passenger Hand Hold Always adjust the hand

hold to a comfortable position for your passenger before operating. Make sure the clasps are fully locked after making adjustments.

page 42

page 118

–

Lock adjustable steering wheel

Alternator Belt Inspect for cracks,

Do not adjust the steering wheel while the vehicle is moving.

damage. Replace, if necessary.

–

SAFETY

Improper tire maintenance can lead to loss of control and an accident, which could result in serious injury or death. To reduce your risk of injury:

• Maintain POLARIS recommended tire pressure. Check pressure before operating. Even if your vehicle has only been driven a short distance, the tire pressure readings can become higher.

• Make sure tire pressures match the specifications listed in the table below.

• Only use the size and type of tires specified for this vehicle.

• Do not operate your vehicle with worn or damaged tires.

• Always follow your tire manufacturer’s instructions for maintenance.

MEASUREMENT SPECIFICATION

Maximum Cargo Box Load 300 lbs (136 kg)

Tire Pressure in PSI (kPa) Front: 15 (103)

Rear: 15 (103)

Maximum Weight Capacity Includes weight of operator, passenger, cargo, and accessories

740 lbs (336 kg)

SAFETY

PREPARE YOURSELF, PASSENGERS, AND CARGO FOR THE RIDE

Wear an approved helmet. Riding in this vehicle without wearing an approved

helmet increases the risk of serious injury. For example, a helmet reduces your risk of injury from head strikes with the vehicle or other objects even if there is no crash.

Approved helmets in the USA and Canada bear a U.S. Department of Transportation (DOT) label. Approved helmets in Europe, Asia, and Oceania bear the ECE

22.05 label. The ECE mark consists of a circle surrounding the letter E, followed by the distinguishing number of the country which has granted approval. The approval number and serial number will also be displayed on the label.

Use shatterproof goggles or a shatterproof helmet face shield. Such protective eyewear may reduce the risk of foreign material getting in your eyes and help prevent loss of vision.

POLARIS recommends wearing approved Personal Protective Equipment (PPE) that have markings indicating they are designed to standards such as:

• VESC 8

• V-8

• Z87.1

• CE

Additional protective clothing and gear that may be appropriate for your riding conditions includes:

• Always wear shoes when operating. Consider wearing sturdy over-the-ankle boots suitable for the terrain you will be riding in.

• Full-finger gloves can protect against wind, sun, cold, and objects. Choose gloves that fit snugly and allow fingers to move freely and grip on the steering wheel or hand holds.

• Consider long sleeves and long pants to help protect arms and legs.

• Long-term exposure to wind and engine noise can cause permanent hearing loss. Properly worn hearing protective devices such as earplugs can help prevent hearing loss. Check local laws or the rules of the riding area you are in before wearing hearing protection to make sure its use is permitted.

SAFETY

Always stay completely inside the vehicle and hold the steering wheel or hand holds. Body parts outside of the vehicle can be struck by passing objects

or crushed during a rollover. Do not put any part of your body outside of the vehicle for any reason. Do not hold onto the ROPS frame or put any part of your body on the door.

Riding in this vehicle without closed and latched cab doors increases the risk of serious injury or death in the event of an accident or rollover. Always make sure all cab doors are closed and latched while riding in this vehicle.

Be sure riders pay attention and plan ahead. If you think or feel the vehicle may tip or roll, reduce your risk of injury:

• Keep a firm grip on the steering wheel or hand holds and brace yourself.

• Do not put any part of your body outside of the vehicle for any reason.

This vehicle is not designed to carry unrestrained pets. An unrestrained pet can be thrown about and injure riders, even during normal operation. When transporting pets, use a pet crate suitable for off-road use that is secured to the vehicle.

Fuels such as gasoline can be extremely flammable. To reduce the risk of serious injury or death, never carry fuel or other flammable liquids on this vehicle. Rollovers, crashes, rough riding, or changes in elevation or temperature may lead to fuel spilling or vapor release from portable containers. Hot vehicle parts can cause fires, even after the engine has been turned off.

Never exceed vehicle weight capacities. The vehicle’s maximum weight capacity (including riders, cargo, and accessories) is 740 lbs. (336 kg) total. The cargo box can support up to 300 lbs. (136 kg) of that total. When more rider weight is added, cargo weight may need to be eliminated to stay under the 740 lb. (336 kg) limit. Overloading the vehicle or carrying cargo improperly will cause changes in stability and handling, which could cause loss of control or an accident.

Secure cargo in the cargo box as far forward, centered and as low as possible. When cargo cannot be positioned and secured in this way, operate

with extra caution. Unsecured cargo can strike and injure riders, affect vehicle handling, and result in loss of control.

The weight of riders and cargo changes vehicle braking, handling, and stability. To avoid loss of control, turn gradually, operate at slower speeds, and

avoid rougher or steeper terrain.

SAFETY

DRIVING GUIDELINES

Drive Responsibly. This vehicle has higher

ground clearance and other features to handle rugged terrain. It can be overturned in situations where some other vehicles may not. Abrupt maneuvers or aggressive driving, even on flat, open areas, can cause loss of control, rollovers, severe injury or death. To avoid loss of control and rollovers:

• Avoid abrupt maneuvers, sideways sliding, skidding, or fishtailing, and never do donuts.

• Slow down before entering turn.

• Avoid hard acceleration when turning, even from a stop.

High speed off-road operation

Driving off-road vehicles to test the limits of your skills or abilities can be very dangerous to you, passengers, and bystanders. Basic skills for driving a car, ATV, or other off-road vehicles do not equip drivers to safely attempt high speed off-road operation. Develop your skill gradually through training, practice, and experience with the various driving modes of this vehicle and the terrain in which you are operating. Always do a low speed reconnaissance run (prerun) to become aware of anything you may encounter.

High speed off-road operation can lead to loss of control, crashes, or hard landings that can seriously injure occupants (even without rolling the vehicle or damaging it).

If you plan on using the vehicle for high speed, off-road competition, additional safety equipment may be necessary. Check the rules that apply to your competition.

Do not go over jumps — going airborne can lead to serious injury or death.

Going airborne can cause loss of control, rollovers, or crashing into the ground and may damage the vehicle. Even without crashing, landings can be hard enough to cause any vehicle suspension to fully compress (e.g., bottom out). Serious injuries, including spinal injuries, can occur even if riders are properly harnessed, wearing helmets and the vehicle is not damaged and remains upright.

You may encounter slopes, "jumps", or other terrain features that could send the vehicle airborne, depending on your speed. These may be defectively designed, poorly maintained, or not suitable for this vehicle. Slow down, use extra care, and avoid going airborne. Never take this vehicle over jumps.

SAFETY

Watching someone else go over a jump or go airborne does not mean you can safely do so. Polaris cannot determine whether any jump you may encounter is appropriate for this vehicle. Any jump, even a small one, could be poorly maintained, designed, or not suitable for this vehicle and may cause serious injury or death.

Plan for hills, rough terrain, ruts, and other changes in traction and terrain.

Proceed slowly and with extra care on unfamiliar terrain. Avoid paved surfaces. Sudden changes in terrain such as holes, depressions, banks, softer or harder ground, or other irregularities may cause loss of control or rollover. Give yourself time to react to rocks, bumps, or holes that may be hard to see. Operating in deep snow or tall grass may make it harder to see obstacles.

If you cannot go around an obstacle, such as a fallen tree or a ditch, stop the vehicle in a safe place. Get out to inspect the area thoroughly. Look from both your approach side and exit side. If you are reasonably confident you can continue safely, choose the path that will allow you to go straight over the obstacle to minimize the vehicle tipping sideways. Go only fast enough to maintain your momentum, but still give yourself plenty of time to react to changes in conditions. If there is any question about your ability to maneuver safely over the obstacle, you should turn around if the ground is flat and you have the room, or back up until you find a less difficult path.

Abrupt application of the accelerator pedal can cause the tires to lose traction, reducing control of the vehicle and increasing the possibility of an accident, especially while on sloped terrain or while crossing obstacles such as rocks or logs.

Avoid Operating on Public Roads (Paved or Otherwise). This vehicle does not have highway safety features that on-road vehicles may have (air bags, antilock brakes, stability control, etc.). If another vehicle collides with you, the likelihood of a serious injury or death may be greater. Also, you may not be able to avoid a crash or rollover if you make sudden or abrupt maneuvers such as swerving or emergency braking.

While it may be legal locally to drive on some public roads in specific parts of the country, your vehicle was not designed or certified as an on-road motor vehicle. Polaris does not support public road use except as may be necessary to crossroads designated for connecting off highway vehicle trail segments. If you must drive on-road, drive slowly and defensively. Your vehicle may lack the features needed to comply with state or local laws that permit limited public road use. Modifications you make to your vehicle to meet these requirements may void the vehicle warranty. In addition, refer to tire manufacturer’s instructions or limitations for on-road operation, including speed limits and premature tire wear.

SAFETY

Improperly operating on hills can cause loss of control, rollover, or accident, which can lead to serious injury or death. Use extra care when

operating on hills. Plan for rough terrain, ruts, and other changes in traction and terrain.

Driving up hills

Check the terrain before ascending a hill and make sure it is not too slippery or loose. Engage all-wheel drive for hills. Drive straight uphill, keeping speed and throttle steady. Avoid steep hills which can cause the vehicle to overturn.

Recovering from stalling on a hill

If the vehicle loses forward speed, apply the brakes gradually and stop. Do not attempt to turn the vehicle around. Instead, shift to reverse and allow the vehicle to slowly roll straight downhill. Apply light brake pressure to control speed.

Overtopping a hill

Slow down when you reach the crest of a hill. Never blindly go over the crest of a hill or a drop off at high speed. An obstacle, a sharp drop, or another vehicle or person could be on the other side of the hill.

Driving down hills

Check the terrain before descending a hill and make sure it is not too slippery or loose. Engage all-wheel drive and proceed slowly, applying the brakes lightly. Never descend a hill with the transmission in neutral or if the engine is turned off.

Avoid side hilling (riding across slopes)

If unavoidable, proceed slowly and with extra caution. Avoid obstacles and changes in terrain that could cause the vehicle to tip or slide. If it feels like the vehicle begins to tip or slide, immediately turn downhill.

Riding near wooded areas or brush

Use extra caution when operating near trees, particularly when operating on narrow trails. Tree branches or brush can be driven into the cab striking or stabbing occupants.

SAFETY

Riding in snow

Always keep the brake and accelerator pedals free of snow and ice. Apply the brakes frequently to prevent ice or snow accumulation on the brake pads which can reduce brake performance.

Riding on ice

Never operate the vehicle on a frozen body of water unless you have verified that the ice can support the weight of the vehicle. Severe injury or death can result if the vehicle falls through the ice.

Riding in water / Falling into water

Operating through deep or fast-flowing water can cause loss of traction, loss of control, overturning, or being swept away in water. You can be seriously injured or killed from entrapment and drowning. Never operate the vehicle in fastflowing water or in water that exceeds the floor level of the vehicle. Avoid sharp drop-offs and large rocks. Choose a path that provides an entrance and exit point with gradual inclines. Wet brakes may have reduced stopping ability. After leaving water, test the brakes. Apply them lightly several times while driving slowly. The friction will help dry out the pads.

Riding on sand dunes

Use extra caution when operating on or near dunes. Be alert for changes in terrain. Never blindly go over the crest of a hill or a drop-off at high speed. An obstacle, a sharp drop, or another vehicle or a person could be on the other side of the hill.

Riding in low-visibility conditions

Use extra caution and drive slowly in conditions of reduced visibility such as fog, rain, and darkness.

Plan ahead to avoid the need for evasive maneuvers, such as swerving.

Hitting an obstacle — including wildlife — you are not ready for can be dangerous. Choosing to swerve instead can be even more dangerous because it can lead to loss of control, rollover, or collisions.

When operating in areas with possibility of wildlife appearing in your path, plan ahead to avoid swerving for animals if doing so could result in collisions or rollovers. Go slowly or avoid driving during seasons or times of day when animals such as deer are more likely to cross your path without warning.

SAFETY

Avoid Collisions With Other Vehicles

When following another vehicle or operating in the same area as others, keep a safe distance to avoid collisions. Allow extra space when sight distances are limited by dust, snow, curves, hills, or other conditions. Plan ahead to avoid having to swerve or leave the trail to avoid a collision.

On trails, be prepared to make space for other vehicles to pass. If you need to stop on a trail, move your vehicle to the edge of the path to allow others to pass safely.

Correct a skid by turning the steering wheel in the direction of the skid.

Never apply the brakes during a skid.

If the vehicle begins to slide downhill or you feel it may tip, turn downhill immediately and stop. Maneuver slowly and carefully until you can drive straight downhill.

Do not continue driving if your vehicle may be damaged or if you were in a crash or rollover.

Operating the vehicle while damaged or after a crash or rollover can cause loss of control, rollover, or accident, which can lead to serious injury or death. If you cannot safely transport the vehicle on your own, contact a recovery and towing service.

After any crash, rollover, or other accident, have a POLARIS dealer inspect the vehicle for possible damage, including seat belts, ROPS, brakes, suspension, and steering systems.

Be prepared in case your vehicle becomes damaged or disabled, especially in remote areas. Consider in advance how to get help and stay safe until it arrives whenever you ride.

The vehicle does not have a tow hitch and is not designed to tow another vehicle for any distance.

Towing can alter vehicle handling and may cause loss of control.

SAFETY

There is a recovery tow loop at the front and back of the vehicle to attach a winch or strap.

Use these loops to recover this vehicle if it is stuck, to pull it onto a tow truck, trailer, or to use this vehicle to recover another vehicle. These loops are for emergency recovery only and are not for towing vehicles to another location.

Improper recovery may lead to loss of control or vehicle damage. Only attach straps to specified locations. Do not attach to any other point on the vehicle. Only recover a vehicle of equal or lesser size and weight. When recovering a disabled vehicle, place the disabled vehicle’s transmission in neutral. Do not move a disabled RZR faster than 10 mph (16 km/h).

Operating, Idling, Or Parking Near Combustible Materials

Engine, exhaust, and other vehicle components can be very hot during and after use. Do not idle or park the vehicle over anything that could contact the exhaust system and catch on fire, such as tall grass, weeds, brush, leaves, debris, or other tall ground cover. Do not let mud, grass, or other debris accumulate on the engine or exhaust system. Inspect and remove as needed.

Vehicle rollaway can cause serious injury or death. This vehicle can roll whenever the gear selector is not in the PARK (P) position. Always shift to PARK (P) when stopping the engine or leaving the vehicle. When leaving the vehicle on an incline is unavoidable, use extra care. If leaving the vehicle unattended, block the rear wheels on the downhill side and keep children, pets, and others away from the gear selector.

Before shifting into reverse, use extra care to make sure the area is clear of people or obstacles. When it’s safe to proceed, back slowly.

SAFETY

After operation, inspect the vehicle for damage and debris to make sure the vehicle can be safely stored and operated again. Some things to inspect include:

• Debris that could catch fire, such as mud/grass near the engine or exhaust system

• Damage to the suspension, steering, or any other part of the vehicle

• Tire condition, such as tread and sidewall damage

• Shock absorber assembly condition

Be sure to have any issues checked and problems fixed before operating again.

All engine exhaust contains carbon monoxide, a deadly gas. Breathing carbon monoxide can cause headaches, dizziness, drowsiness, nausea, confusion, and eventually death. Carbon monoxide is a colorless, odorless, tasteless gas which may be present even if you do not see or smell any engine exhaust. Deadly levels of carbon monoxide can collect rapidly, and you can quickly be overcome and unable to save yourself. Also, deadly levels of carbon monoxide can linger for hours or days in enclosed or poorly ventilated areas. If you experience any symptoms of carbon monoxide poisoning, leave the area immediately, get fresh air, and SEEK MEDICAL TREATMENT.

• Do not run engine indoors. Even if you try to ventilate engine exhaust with fans or open windows and doors, carbon monoxide can rapidly reach dangerous levels.

• Do not run engine in poorly ventilated or partially enclosed areas such as barns, garages, or carports. If you start a vehicle in one of these, drive it out and close the door as soon as possible. If you drive it into one of these, turn it off as soon as possible.

• Do not run engine outdoors where engine exhaust can be drawn into a building through openings such as windows and doors.

SAFETY

SAFETY LABELS AND LOCATIONS

OVERVIEW

Warning labels have been placed on the vehicle for your protection. Read and follow the instructions of the labels on the vehicle carefully. If any of the labels depicted in this manual differ from the labels on your vehicle, always read and follow the instructions of the labels on the vehicle

Never remove any labels from your vehicle. If a label becomes illegible or comes off, contact your POLARIS dealer for a replacement. Replacement safety labels are provided at no charge.

Driver Information Warning

Load/Passenger/Tire Pressure Warning

Fuel Transport Warning

Air Box Caution (On Air Box)

Alternator Drive System Warning (On Alternator Cover)

SAFETY

DRIVER INFORMATION WARNING

WARNING

FOLLOW ALL INSTRUCTIONS AND WARNINGS.

Improper vehicle use can result in SEVERE INJURY or DEATH.

Be Prepared

• Fasten seat belts.

• Wear an approved helmet and protective gear.

• ALWAYS use cab nets and/or doors.

• Each rider must be able to sit with back against seat, feet flat on the floor, and hands on steering wheel or hand holds. Stay completely inside the vehicle.

Drive Responsibly

Rollovers have caused severe injuries and death, even on flat, open areas.

Avoid loss of control and rollovers:

• Avoid abrupt maneuvers, sideways sliding, skidding or fishtailing, and never do donuts.

• Slow down before entering a turn.

• Avoid hard acceleration when turning, even from a stop.

• Plan for hills, rough terrain, ruts and other changes in traction and terrain.

• Avoid paved surfaces.

• Avoid sidehilling (riding across slopes).

Require Proper Use of Your Vehicle

Do your part to prevent injuries:

• Do not allow careless or reckless driving.

• Make sure operators are 16 or older with a valid driver’s license.

• Do not let people drive or ride after using alcohol or drugs.

• Do not allow operation on public roads (unless designated for off-highway vehicle access) - collisions with cars and trucks can occur.

• Do not exceed seating capacity: 1 passenger.

Be Sure Riders Pay Attention and Plan Ahead

If you think or feel the vehicle may tip or roll, reduce your risk of injury:

• Keep a firm grip on the steering wheel or hand holds and brace yourself.

• Do not put any part of your body outside of the vehicle for any reason.

SAFETY

LOAD / PASSENGER / TIRE PRESSURE WARNING

WARNING

• Never carry passengers in cargo box.

• Passengers can be thrown off. This can cause serious injury or death.

IMPROPER TIRE PRESSURE OR OVERLOADING CAN CAUSE LOSS OF CONTROL RESULTING IN SERIOUS INJURY OR DEATH.

• Reduce speed and allow greater distance for braking when carrying cargo.

• Overloading or carrying tall, off-center, or unsecured loads will increase your risk of losing control. Loads should be centered and carried as low as possible in box.

• For stability on rough or hilly terrain, reduce speed and cargo.

PRO R

MAXIMUM CARGO BOX LOAD 300 lbs.

(136 kg)

TIRE PRESSURE IN PSI (KPa) FRONT 15 (103)

REAR 15 (103)

MAXIMUM WEIGHT CAPACITY

INCLUDES WEIGHT OF OPERATOR, PASSENGERS, CARGO AND ACCESSORIES

Read Operation and Maintenance Manual for more detailed loading information.

740 lbs. (336 kg)

FUEL TRANSPORT WARNING

WARNING

NEVER carry fuel or other flammable liquids on this vehicle.

Failure to follow this instruction could lead to serious burn injuries or death.

SAFETY

AIR BOX CAUTION

CAUTION

Use a Polaris approved air filter. The use of a non-Polaris approved air filter may cause engine damage. Before installing filter, ensure there is no dirt or debris in the clean side of the intake tube. The air filter must be properly seated before the lid is reinstalled. Please reference your owner’s manual for additional information regarding air filter service.

ALTERNATOR DRIVE SYSTEM WARNING

WARNING

AVOID SERIOUS INJURY

Do not operate with belt and/or alternator cover removed or belt exposed.

Replace covers before operating vehicle.

FEATURES AND CONTROLS

NEAR-FIELD COMMUNICATION (NFC)

Some Polaris vehicles come equipped with a near-field communication (NFC) chip. The NFC chip is embedded in the Polaris emblem located at the front of the vehicle and seamlessly connects you to a digital platform of vehicle information and tools. See your dealer for more information.

IMPORTANT

Not all devices are equipped with an NFC reader. Additionally, some devices

require third party applications to access NFC content. For questions regarding

the NFC reader on your device, refer to the device’s user manual.

On models equipped with NFC, place your smartphone directly over the Polaris emblem to do the following:

• View vehicle-specific information

• Access your Polaris Garage

• Download and view the owner’s manual

• View accessory instructions

• Watch how-to videos

• Access warranty information

• Check for service notifications

RIDE COMMAND WITH NFC

Additional NFC features are available when using the Ride Command mobile app. To access these features, do the following:

1. Download the Ride Command mobile app from the Apple App Store® or

Google Play® store.

2. Create or log in to an existing account.

3. From the Ride Command mobile app home screen, select Add Vehicle.

4. On the vehicle, tap the NFC-enabled badge with the phone to scan the

vehicle.

5. Confirm information, name your vehicle, and tap add to garage.

SYSTEM REQUIREMENTS

Refer to device manufacturer’s instructions to verify NFC read capability, and/or NFC-capable add-ons.

FEATURES AND CONTROLS

COMPONENT LOCATIONS

Roof

ROPS Frame

Steering Wheel

Front Lights

Radiator

Cargo Box

Tail Lights

Fuel Cap

Cab Door

FEATURES AND CONTROLS

STEERING WHEEL ADJUSTMENT

STANDARD STEERING WHEEL (IF EQUIPPED)

On models equipped with a standard steering wheel, the steering wheel can be tilted upward or downward for rider preference. Lift and hold the steering wheel adjustment lever while moving the steering wheel upward or downward. Release the lever when the steering wheel is at the desired position.

TELESCOPE STEERING WHEEL (IF EQUIPPED)

On models equipped with a telescope steering wheel, the steering wheel can be adjusted by pressing the release lever

Once released, the steering wheel can be tilted up/down and telescoped in/out freely.When desired position is found, hold the steering wheel in place with one hand and pull the release lever back up with the other. The release lever will catch into place when it is locked.

downward.

FEATURES AND CONTROLS

SWITCHES

IGNITION SWITCH

The ignition switch q is a four-position, key-operated switch. Use the ignition switch to start the engine. See the Starting the Engine section for starting procedures.

POSITION FUNCTION

OFF

ACCESSORY

START

The engine is off. Electrical circuits are off, except accessory 12V.

The engine is off. Powers the display, terminal block, and front/rear accent lights. Check engine and power steering warning indicators will appear on the display in this mode but will turn off when the vehicle is started if no issues are present.

Electrical circuits are on. Electrical equipment can be used.

The vehicle must be in PARK or NEUTRAL before the engine can start. To start the vehicle, press the brake pedal, turn the key to the start position, and then release. The engine will turn over for about 5 seconds or until started.

The key can be removed from the switch when it is in the OFF position.

FEATURES AND CONTROLS

HEADLIGHT SWITCH

The ignition switch key must be in the ON/RUN position to operate the headlights. The headlight switch is a toggle and has three positions:

High Beams

Low Beams

Headlights Off

DRIVELINE MODE (AWD) SWITCH

The ignition switch key must be in the ON/RUN position to operate the Driveline Mode system. The Driveline Mode switch is a toggle and has three positions:

All Wheel Drive (AWD)

Lock

All Wheel Drive (AWD)

Unlock

Two Wheel Drive (2WD)

FEATURES AND CONTROLS

DRIVE MODE SWITCH

The Drive Mode Switch is a toggle with three positions:

Race Mode

Rock Mode

Sport Mode

MODE DESCRIPTION

Race Mode

Rock Mode

Sport Mode

Allows MAX engine feedback when pressing the throttle pedal.

Allows minimized engine feedback when pressing the throttle pedal.

Allows slightly less than MAX engine feedback when pressing the throttle pedal.

FEATURES AND CONTROLS

AUXILIARY OUTLETS

WARNING

To avoid electric shock, do not touch power outlets with wet hands or insert any object that the power outlet is not designed to receive. Close the lid when not in

use.

NOTICE

The front console accessory outlet is always active. The accessory outlet in the

armrest storage bin is only active when the ignition switch is set to ON.

The vehicle is equipped with two 12-volt accessory outlets. One is in the front portion of the center console, in front of the gear selector. The other is in the armrest storage bin. Use the outlets to power an auxiliary light or other optional accessories.

VEHICLE BATTERY CHARGE PORT

This vehicle is equipped with a vehicle battery charge port located on the dash. This allows the operator to charge the vehicle battery without needing to access the battery under the driver’s seat. See the Battery Maintenance and Charging section for details.

FEATURES AND CONTROLS

ELECTRONIC POWER STEERING (EPS)

Electronic power steering engages when the ignition key is turned to the ON position. EPS remains engaged whether the vehicle is moving or idle.

The EPS warning indicator briefly illuminates when the key is turned to the ON position. See the Indicator Lamps section for details.

If the engine is off but the ignition switch remains in the ON position, the EPS will shut down after 5 minutes of engine inactivity. The EPS warning indicator will illuminate to indicate the EPS has shut down.

NOTE

The EPS shuts down automatically to conserve the battery power of your

vehicle.

If the EPS warning indicator remains on after turning the ignition switch to OFF and then starting the engine, the EPS system is inoperative. See your POLARIS dealer, or another qualified person, as soon as possible for repair. Continued operation could result in permanent damage to the EPS unit and increased steering effort.

FEATURES AND CONTROLS

STEERING WHEEL CONTROLS

RIDE MODE CONTROLS (IF EQUIPPED)

If equipped, Ride Mode controls can be found on the right-hand side of the steering wheel. There are 4 available modes to select from: Baja, Rock, Track, and Comfort. The UP and DOWN arrow buttons are used to cycle through the different modes.

The momentary MAX FIRM button is on the right. When this button is pressed, the suspension will immediately switch to maximum compression damping. The vehicle will maintain this setting if the button is continuously pressed. Once the button is released, maximum compression damping will persist temporarily, and then revert back to the previous setting.

NOTICE

The system will prevent mode transitions when a current vehicle state is

present (cornering, braking, or accelerating).

FEATURES AND CONTROLS

MODE SUSPENSION

DESCRIPTION

Baja Mode High compression and low

rebound damping for large and aggressive suspension events.

Rock Mode High compression and low

rebound with angle based damping adjustments for maneuvering through rockier terrain. At higher vehicle speeds, damping becomes similar to Comfort Mode.

Track Mode Medium compression and

high rebound damping for frequent cornering events.

Comfort Mode

Low compression and rebound damping to allow the shock to move and absorb smaller suspension events.

POWER STEERING

DESCRIPTION

Good feeling of the front wheels with excellent bump rejection.

High assist level and bump rejection for low steering effort when maneuvering in rocks.

Best feeling of the front wheels for frequent cornering events.

High assist level and bump rejection for low steering effort and maximum comfort.

“Demo” Mode “Demo” Mode allows the operator to experience the feel

associated with each Ride Mode before actual use. Activate “Demo” Mode by placing the vehicle in Park (P) and turning off the engine, then turn the ignition key switch to ON position. The operator can cycle through the different Ride Modes using the UP or DOWN arrow buttons, then use the throttle, brakes, and steering wheel to assess the feel of each Ride Mode.

FEATURES AND CONTROLS

AUDIO CONTROLS (IF EQUIPPED)

If equipped, audio controls can be found on the left-hand side of the steering wheel. Volume can be adjusted by pressing the bottom (lower volume) or the top (higher volume) of the button.

Audio can be paused or resumed by pressing the pause button.

Refer to the Ride Command manual for operating the third Polaris button.

FEATURES AND CONTROLS

SEATS

SEAT REMOVAL

To adjust the seat, do the following:

1. Pull up on the seat latch lever the front edge of the seat.

2. Tilt the seat forward.

3. Lift the seat upward to remove it from the vehicle.

located under

4. Reverse this procedure to reinstall the seat. Make sure the seat tabs at the front edge of the seat slide onto the seat retainer tubes.

5. Press down firmly at the rear of the seat to engage the rear latches.

SEAT ADJUSTMENTS

DRIVER’S SEAT ADJUSTMENT

On seats equipped with an adjustment lever q under the front edge of the seat, pull the lever to the left. Slide the seat forward or rearward to the desired position. Release the lever. The seat will lock into the new position.

To adjust seat tilt, adjustment bolts can be removed and reinstalled at a different tilt setting. The driver side has two adjustment bolts side, and has three tilt hole options. Re-install the bolts to specification when finished with adjustments.

, one on each

Seat Adjustment Bolts:

15 ft-lbs (20 N

FEATURES AND CONTROLS

TORQUE

⋅m)

PASSENGER SEAT ADJUSTMENT

To adjust the passenger seat position, remove the seat and remove the four bolts on the two seat frame members. The seat frame members can be moved forward (or backward) to the desired position.

The passenger seat can also be tilted up/down (similar to the driver seat) using the three tilt hole options. Choosing which set of tilt holes to use is dependent on whether the seat position has been moved forward or backward. Re-install the bolts to 15 ft-lbs (20 N⋅m) of torque when finished with adjustments.

located

TORQUE

Seat Adjustment Bolts:

15 ft-lbs (20 N

⋅m)

FEATURES AND CONTROLS

PASSENGER HAND HOLD

To adjust the passenger hand hold, do the following:

1. Unlock the two passenger hand hold clasps

2. Pull or Push the bar to desired position.

3. Lock both clasps back into place.

FUEL

WARNING

Gasoline and gasoline vapor is highly flammable and explosive. Refuel

outdoors or in a well ventilated area free of any source of flame or sparks,

including pilot lights from water heaters, furnaces, or clothes dryers. To avoid

fires and explosions, follow these precautions when refueling.

• Do not smoke.

• Wipe up any spilled fuel.

WARNING

Gasoline is poisonous. To avoid injury or death, avoid contact with gasoline

and follow these precautions:

• Never attempt to siphon gasoline by mouth.

• If gasoline is ingested, contacts eyes, or gasoline vapor is inhaled, immediately seek medical attention.

• If gasoline contacts skin, wash with soap and water.

• If gasoline contacts clothes, change out of them.

FEATURES AND CONTROLS

REFUELING

The fuel tank filler cap is located on the right side of the vehicle near the passenger seat.

The fuel symbol and the last fuel bar on the Instrument Cluster will blink when the fuel level reaches 1/8th tank. There will be approximately 2 gallons (8 L) of fuel remaining. Refuel as soon as possible. Do not allow the vehicle to run out of

fuel.

To refuel:

1. Place the transmission into Park on a level surface.

2. Turn off the engine.

3. Make sure no one is inside the vehicle.

4. Fill with fuel, leaving the tank neck empty.

5. Securely close fuel cap.

NOTE

Gasoline can expand while inside the tank. To avoid fires and explosions,

do not overfill the tank. Allow room for gasoline to expand inside the tank by

leaving the tank neck empty.

• Use only 91 octane (or higher) unleaded fuel (minimum pump octane number of 91 R+M/2)

• Do not use any fuel lower than 91 octane.

• Do not fuel containing more than 10% ethanol (including E85)

NOTICE

Damage to the fuel pump will occur if the vehicle is operated with an empty fuel

tank. Do not allow the vehicle to run out of fuel. Always refuel when the level is

low.

NOTICE

Operating with obstructed fuel systems will result in serious engine damage.

Perform maintenance as recommended.

NOTICE

Prolonged exposure to petroleum based products may damage paint. Always

protect painted surfaces when handling fuel.

FEATURES AND CONTROLS

SEAT BELTS

This POLARIS vehicle is equipped with seat belts for all riders. Always make sure the seat belts are secured for the operator and all passengers before riding. The driver’s seat belt is equipped with a seat belt interlock. Vehicle speed will be limited to 15 mph (24 km/h) if the seat belt is not secured.

MULTI-POINT SEAT BELT

This vehicle is equipped with an IMMI safety harness with built-in interlock. The safety harness requires proper adjustment for each rider and will need to be adjusted when riders change seats.

WARNING

Improper use or adjustment of the harness can cause serious injury or death.

For example, you can slide under the harness in an accident if the lap belt

portion of the harness is not pressed against the pelvic bones. Always adjust

the harness for each rider to make sure it fits them.

Shoulder Belt

Harness Pads

Tilt-locks

Chest Clip

Buckle Release Button

Harness Buckle

Thigh Belt

Lap Belt

FEATURES AND CONTROLS

INSPECTING THE HARNESS

WARNING

Failure to perform regular inspection can reduce the effectiveness of the seat

belt during a crash and could result in serious injury or death.

Before each ride, perform the following inspection:

1. Inspect belt fabric on entire system for cuts, fraying, extreme or unusual wear. Most common areas of belt wear include the buckle/ tongue area, the shoulder guide area and any place where the belt makes contact with vehicle or seat.

Corrective Action: Replace entire belt system

2. Inspect buckle for proper operation by inserting tongue and listening for an audible click. Verify buckle is not damaged, cracked or broken.

Corrective Action: Replace entire belt system

3. Inspect electrical wires (optional component). Internal cable wires must not be exposed, frayed or broken.

Corrective Action: Replace entire belt system

FEATURES AND CONTROLS

4. Inspect tongue for proper operation by inserting into buckle. Tongue must insert smoothly and you must hear an audible click. Verify proper latching by tugging on belt. Tongue must not be worn, deformed or corroded.

Corrective Action: Replace entire belt system

5. Inspect shoulder web guide. Seat belt must move freely through shoulder web guide. Shoulder web guides must be free of obstructions and must not snag or wear webbing fabric.

Corrective Action: Adjust shoulder web guide hardware and/or remove obstruction.

6. Inspect retractor operation (if equipped). When pulled and released slowly, seat belt must spool out and retract without locking.

Corrective Action: Replace entire belt system

7. Inspect mounting hardware on all belt system attachment points. Hardware should be tight. Hardware must not be missing, rusted, corroded or damaged.

Corrective Action: Replace defective or missing hardware with authorized parts and or tighten hardware.

8. If a harness is used to restrain a rider during an accident, that entire harness system must be replaced. Inspect non-retractable harness pads containing controlled deceleration technology for evidence of a blown fuse (e.g., exposed threading).

Corrective Action: Replace entire belt system

FEATURES AND CONTROLS

PUTTING ON THE HARNESS

To prepare the rider:

1. Do not wear heavy clothing that may interfere with proper fit of the harness. Make sure there are no rigid or breakable items (e.g., eye glasses, pens, jewelry, keys) under the harness.

2. Before entering the vehicle, your helmet should be off, but accessible from the seat.

3. Adjust the seat to the desired position.

4. Unbuckle the harness and loosen all manually adjustable belts:

• Lap belts

• Thigh belts (equipped on 6-pt harnesses)

• Shoulder belts (not adjustable on retractable 6-pt harness)

How to use the red straps and tilt-lock feature to tighten and loosen the belts:

When the tilt-lock is down red straps are provided so that you can lift the tilt-lock to the up position unlock it so that you can pull the seat belt through. To tighten or loosen a belt, grasp the red strap and pull up on the red strap in one hand and pull the belt with the other. Adjust the angle of the tilt-lock until the belt pulls more easily.

, the belt resists being tightened or loosened. The

and

Down, locked position

Up, unlocked position

FEATURES AND CONTROLS

To adjust the harness:

1. Put your arms through the shoulder belts. The belts should lay flat and not be twisted. The shoulder belt should not rub against your neck or fall off your shoulder.

2. Buckle the harness and check the fit of the lap belt. It should be as short as possible and pressed against your pelvic bones so that you cannot lift yourself from the seat bottom at all. Unbuckle and tighten the lap belts as needed until the seat belt is properly adjusted – it is easier to adjust the belts while unbuckled. Finally, buckle the harness and listen for a click. Check fit and make sure buckle is secure.

3. Tighten shoulder belts. If your harness is equipped with non-retracting, adjustable shoulder belts, tighten the shoulder belts until they are snug across your chest when your back is against the seat. When tightening the shoulder belts, be sure to keep the harness buckle centered and below your belly button. The lap belt must remain pressed against your pelvic bones.

4. Tighten thigh belts. If your harness is equipped with thigh belts, adjust them for comfort and be sure to keep the harness buckle centered and below your belly button. The lap belt must remain pressed against your pelvic bones.

5. Attach the chest clip between the shoulder belts.

6. Put on your helmet.

FEATURES AND CONTROLS

To take off the harness:

1. Unlatch the chest clip.

2. Push the red button to release the buckle.

3. Remove your arms from the shoulder belt.

4. After exiting the vehicle, buckle the harness to prevent damage which can occur if it is slammed in the door or hangs out of the vehicle.

SUB ZERO SEAT BELT HARNESS

CAUTION

If the red warning section of the safety label becomes visible at all times, this

harness must be replaced.

On models equipped with a Sub Zero seat belt harness, the harness is designed to extend in the event of accident to absorb the impact. The harness must be replaced if the red section on the label appears outside the shoulder pad.

FEATURES AND CONTROLS

SERVICE ACCESS PANELS

ENGINE ACCESS PANEL

The engine access panel is located behind the seats. Adjust or remove the seats, then remove the panel to reach serviceable engine components. Remove the panel by turning the close-off knobs

CARGO BOX ACCESS

The entire cargo box layer can be lifted to access the engine oil fill cap and spark plugs by removing the four rear-most screws

1/4 turn.

FEATURES AND CONTROLS

GEAR SELECTOR

The gear selector is located between the driver and passenger seat q To change gears, stop the vehicle and with the engine idling, move the lever to the desired gear. Do not attempt to shift gears with engine speed above idle or while the vehicle is moving.

P: Park R: Reverse N: Neutral L: Low Gear H: High Gear

NOTICE

Maintaining shift linkage adjustment is important to assure proper transmission

function. Your POLARIS dealer can assist in resolving any shifting problems.

NOTICE

Do not attempt to shift the transmission while the vehicle is moving or damage

to the transmission could result. Always shift when the vehicle is stationary and

the engine is at idle.

USING LOW RANGE

NOTICE

Using Low Gear during when conditions require it will prolong the life of your

vehicle’s drive belt.

Always shift into low gear for any of the following conditions:

• Operating in rough terrain or over obstacles

• Loading the vehicle onto a trailer

• When hauling or towing heavy cargo.

• When consistently operating at speeds less than 35 MPH (56 km/h) in hard-

pulling terrain, such as mud, rocks, or sand/dune environments.

FEATURES AND CONTROLS

BRAKE AND THROTTLE PEDALS

BRAKE PEDAL

Depress the brake pedal q to slow or stop the vehicle. The brakes must be applied in order to start the engine.

THROTTLE PEDAL

Push the throttle pedal w down to increase engine speed. Spring pressure returns the pedal to the rest position when released. Always check that the throttle pedal returns normally before starting the engine.

NOTICE

When traveling over 10 mph with the throttle pedal depressed, applying the

brake for more than two seconds will disable the throttle pedal until the brake is

released.

FEATURES AND CONTROLS

ALL WHEEL DRIVE (AWD) SYSTEM

The All Wheel Drive system is controlled by the AWD switch. Once the vehicle is in gear, the switch is set to one of three driveline modes.

ICON DRIVELINE

MODE

All Wheel Drive (AWD) Lock

All Wheel Drive (AWD) Unlock

DESCRIPTION

When in All-Wheel Drive Lock, the front drive is engaged with the front differential in the locked state. The locked state drives all wheels at the same speed which will increase steering effort and changes the handling characteristics from the AWD mode. If switched to AWD Lock when vehicle speed, accelerator pedal position, and engine RPM are above activation limits, AWD Lock will not engage until vehicle speed, accelerator pedal position, and engine RPM are decreased.

When in All-Wheel Drive, the front drive is engaged with the front differential in the open state. The open state allows the front wheels to spin at different speeds for improved turning ability. If switched to AWD Unlock when vehicle speed, accelerator pedal position, and engine RPM are above activation limits, AWD Unlock will not engage until vehicle speed, accelerator pedal position, and engine RPM are decreased.

Two-Wheel Drive (2WD)

Engage the AWD switch before getting into conditions where all-wheel drive may be needed. If the rear wheels are spinning, release the throttle before switching to AWD.

Switching to AWD while the rear wheels are spinning or slipping may cause

severe drive shaft, prop shaft, and gearcase damage. Always switch to AWD

while the rear wheels have traction or are at rest.

When the switch is set to 2WD the vehicle is in two-wheel drive at all times.

NOTICE

FEATURES AND CONTROLS

INSTRUMENT CLUSTER

NOTICE

High water pressure may damage components. Wash the vehicle by hand or

with a garden hose using mild soap. Certain products, including insect

repellents and chemicals, will damage the speedometer lens and other plastic

surfaces. Do not use alcohol or cleaning products containing alcohol to clean

the instrument cluster. Do not allow insect sprays to contact the lens.

Immediately clean off any gasoline that splashes on the instrument cluster.

Speedometer

Tachometer

Indicator Lamps

Mode Button

Toggle Buttons

Rider Information Center

SPEEDOMETER

The speedometer displays vehicle speed in either miles per hour (MPH) or kilometers per hour (km/h).

TACHOMETER

The tachometer displays engine speed in revolutions per minute (RPM).

FEATURES AND CONTROLS

MODE AND TOGGLE BUTTONS

Press and hold the MODE button r to enter or exit the settings menu. Press and release the MODE button to cycle through Area 1 modes and to select an item.

Press and release either toggle button Area 2 modes. Press and hold either toggle button to reset an item. See page

59.

With the ignition key off, pressing the MODE button or either toggle button will

power up the Rider Information Center for 10 seconds to allow viewing of the

odometer and the clock.

to cycle through the options menu or

TIP

OPERATING A DAMAGED VEHICLE

WARNING

Do not continue driving if you think or feel the vehicle may be damaged

or if you were in a crash or rollover. Operating the vehicle while damaged or

after a crash or rollover can cause loss of control, rollover, or accident, which

can lead to serious injury or death. If you cannot safely transport the vehicle

from its current position, contact a recovery and towing service.

After any crash, rollover, or other accident, have a POLARIS dealer inspect the vehicle for possible damage, including seat belts, ROPS, brakes, suspension, and steering systems.

Be prepared in case your vehicle becomes damaged or disabled, especially in remote areas. Consider how to get help and prepare for weather conditions whenever you ride.

FEATURES AND CONTROLS

VEHICLE CONDITION INDICATOR LIGHTS

INDICATOR ICON FUNCTION

Check Engine

Chassis Warning

EPS Warning (if equipped)

This indicator appears if a fault occurs. Do not operate the vehicle if this warning appears. Serious engine damage could result. Your authorized POLARIS dealer can assist.

If a fault condition is detected, the light will remain on as long as the condition exists. Retrieve the error codes for diagnosis. This lamp is also known as an Amber Warning Lamp (AWL).

This indicator illuminates briefly when the key is turned to the ON position. If the light remains on, the EPS system is inoperative. See your POLARIS dealer, or other qualified person, as soon as possible for repair. Continued operation could result in permanent damage to the EPS unit and increased steering effort. For more information, see the Electronic Power Steering (EPS) section.

Engine Hot

Check Battery

This lamp illuminates to indicate an overheated engine. If the indicator flashes, the overheating condition remains, and the system will automatically reduce engine power. If the vehicle continues to operate with this indicator on, the engine will eventually be turned off. If the engine is turned off, check for coolant. If no coolant is present, do not restart the engine. Have the vehicle inspected by your authorized POLARIS dealer.

This warning usually indicates an issue with the vehicle’s alternator. It may be that the alternator belt has failed, the alternator is no longer functional, or the wiring between the alternator and the battery is no longer connected or is damaged.

FEATURES AND CONTROLS

VEHICLE INFORMATION LIGHTS

INDICATOR ICON FUNCTION

Vehicle Speed

PASS (PIN Activated Security System, if equipped)

Low Fuel

When standard mode is selected, speed displays in miles per hour.

When metric mode is selected, speed displays in kilometers per hour.

The security indicator lamp illuminates when the security system is enabled.

The low fuel indicator lamp illuminates when fuel level in the fuel tank is low.

Neutral

Helmet/Seat Belt

The neutral indicator lamp illuminates when the transmission is in neutral and the ignition key is in the ON position.

WARNING

Seat Belt indicator lamp is a reminder to

wear a seat belt before operating. It

does not indicate whether seat belts are

properly secured. There is no indicator

light for the passenger seat(s). The

driver is responsible for ensuring that

everyone is ready to ride.

NOTE

The driver’s seat belt is equipped with a

seat belt interlock. Vehicle speed will be

limited to 15 MPH (24 km/h) if the seat

belt is not buckled.

FEATURES AND CONTROLS

INDICATOR ICON FUNCTION

High Beam

Park Brake (if equipped)

This lamp illuminates when the headlamp switch is set to high beam.

Lamp illuminates when the Park Brake is applied (if equipped).

FEATURES AND CONTROLS

RIDER INFORMATION CENTER

The rider information center is located in the instrument cluster. All segments will light up for one second at start-up.

If the instrument cluster fails to illuminate, a battery over-voltage may have occurred and the instrument cluster may have shut off to protect the electronic speedometer. If this occurs, your POLARIS dealer can provide proper diagnosis.

The information center is set to display standard units of measurement and a 12-hour clock at the factory. To change to metric and/or a 24-hour clock, see the Clock section.

Gear Indicator This indicator displays gear shifter position

H = High Gear L = Low Gear N = Neutral R = Reverse Gear P = Park – = Gear Signal Error (or shifter between gears)

AWD Indicator This indicator displays the active driveline mode when the

vehicle is in gear.

Service Indicator

Fuel Gauge The segments of the fuel gauge show the level of fuel in the

Speed Limitation (if equipped)

A flashing wrench symbol alerts the operator that the preset service interval has been reached. Your POLARIS dealer can provide scheduled maintenance. See page 62 for resetting instructions.

fuel tank. When the last segment clears, a low fuel warning is activated. The outline of the fuel display will flash. Refuel immediately.

This vehicle may be equipped with a maximum speed limitation function. This would be displayed on the screen as “LIM” followed by the speed. “LIM 30” for example.

FEATURES AND CONTROLS

MODE INFORMATION DISPLAYS

The rider information center contains three areas that display mode information.

Area 1 Modes

Engine Temperature Temperature of engine coolant

Vehicle Speed Speed of vehicle

Tachometer Engine speed (RPM)

Area 2 Modes

Odometer The odometer records and displays

Trip Meters (T1/T2) A trip meter records the distance

Engine Hours Total hours of engine operation since

Service Hours Time in hours remaining in the

Description

the distance traveled by the vehicle.

traveled by the vehicle if reset before each trip. To reset, see page 61.

manufacture

programmable service interval. To reset, see page 62.

Trip Time Time length of vehicle operation

since mode was last reset

Area 3 Modes

Clock The clock displays time in a 12-hour

Description

or 24-hour format. To reset, see page

60.

FEATURES AND CONTROLS

ACCESSING MENUS AND OPTIONS

GAUGE SETTINGS MENU

Press and release the MODE button to cycle through the Area 1 modes until the desired default mode displays. See the Mode Information Displays section for details.

Press and hold the MODE button to enter the settings menu.

The OPTIONS screen will display for a few seconds.

1. Press and release either toggle button to cycle to the desired option.

2. Press MODE to select the option.

3. Press either toggle button to cycle to the desired setting.

4. Press MODE to save and exit to the settings menu.

5. Press and hold the MODE button to exit the settings menu.

BACKLIGHT COLOR

The information center backlight can be set to either blue or red.

1. Press and hold the MODE button to enter the settings menu.

2. Press either toggle button to cycle to the “BL COLOR” option. Press MODE to select.

3. Press either toggle button to cycle to the desired setting.

4. Press MODE to save and exit to the settings menu,

FEATURES AND CONTROLS

BACKLIGHT BRIGHTNESS

The information center backlight can be set to either blue or red.

1. Press and hold the MODE button to enter the settings menu.

2. Press either toggle button to cycle to the “BL LEVEL” option. Press MODE to select.

3. Press “UP” button to increase brightness. Press “DOWN” button to decrease brightness.

4. Press MODE to select and exit to the settings menu.

CLOCK

The clock must be reset any time the battery has been disconnected or discharged.

1. Press and hold the MODE button to enter the settings menu.

2. Press either toggle button to cycle to the “CLOCK” option. Press MODE to select.

3. Press either toggle button to cycle to the desired setting (12H or 24H). Press MODE to select.

4. Press either toggle button to change each segment of the clock. Press MODE to accept a change and advance to the next segment.

FEATURES AND CONTROLS

DISPLAY UNITS (STANDARD/METRIC)

1. Press and hold the MODE button to enter the settings menu.

2. Press either toggle button to cycle to the desired “UNITS” option (distance, temperature or volume). Press MODE to select.

3. Press either toggle button to cycle to the desired setting.

4. Press MODE to save and exit to the settings menu.

TRIP METER

Use a trip meter to track the distance traveled during a specific trip or period of time. Reset the meter to zero before traveling.

1. Press either toggle button to cycle to the desired trip meter option (T1 or T2).

2. Press and hold either toggle button until the meter resets to zero.

TRIP TIME

Use a trip time meter to track the travel time during a specific trip. Reset the meter to zero before traveling.

1. Press either toggle button to cycle to the trip time option (TT).

2. Press and hold either toggle button until the meter resets to zero.

FEATURES AND CONTROLS

PROGRAMMABLE SERVICE INTERVAL

The service interval counter is programmed to 25 hours at the factory. As hours of engine operation increase, the counter decreases. The wrench icon will flash for about 10 seconds when the counter reaches zero (0), and each time the key is turned on thereafter, until the counter is reset.

When this feature is enabled, it provides a convenient reminder to perform routine maintenance. Refer to the Periodic Maintenance Chart for recommended service intervals.

Use the following procedure to reset or change the service interval.

1. Press and hold the MODE button to enter the settings menu.

2. Press either toggle button to cycle to the “Service Hours” option. Press MODE to select.

3. Press MODE to reset the existing value and exit, or press either toggle button to change the value. Press MODE to save and exit to the settings menu.

PIN ACTIVATED SECURITY SYSTEM (P.A.S.S.) (IF EQUIPPED) — INSTRUMENT CLUSTER

For vehicles with the Ride Command display, see page 70 for details.

The optional PIN Activated Security System (P.A.S.S.) is to prevent unauthorized use. When enabled, the vehicle cannot be operated until a valid passcode has been entered using the Instrument Cluster.

To enable/disable P.A.S.S. using the Instrument Cluster, follow the procedures below.

ENABLE P.A.S.S.

NOTICE

After activating P.A.S.S. for the first time you must power down the vehicle and

allow the electronic control module (ECM) to fully shutdown before restarting.

This may take up to three minutes.

Once a new passcode has been enabled, it cannot be changed unless you first

disable the system. Then you can re-follow the steps outlined in the ENABLE

P.A.S.S. section to enter a new passcode.

FEATURES AND CONTROLS

1. Press and hold the MODE button to enter the “OPTIONS” menu.

2. Use the UP/DOWN toggle buttons to cycle through options until “REQUIRE PIN TO START” appears. Press the MODE button to select.

3. If required, “ENTER NEW PIN” will appear. Use the UP/DOWN toggle buttons to cycle to your desired first digit. Press the MODE button to select the digit.

4. Continue until all four digits of your desired passcode have been selected. Once finished, “NEW PIN SET” will flash momentarily and then revert back to the “REQUIRE PIN TO START” screen.

Please record your passcode.

5. To enable your new passcode, use the UP/DOWN toggle buttons to change the flashing “OFF” at bottom of screen to “ON”. If this step is skipped, P.A.

S.S. will not be enabled.

6. Press the MODE button to re-enter the “OPTIONS” menu. The vehicle will now require passcode entry before next startup.

You can exit the “OPTIONS” menu three different ways.

• Toggle to “EXIT” and press the MODE button.

• Hold the MODE button for a few seconds.

• Do nothing, allowing the system to automatically revert back to the main

screen.

NOTICE

If the battery becomes low while the P.A.S.S. system is enabled, the gauge

may show “New Vehicle Detected” after the battery has been recharged/

replaced. Leave the key in the ON position to allow system reconfirmation.

DISABLE P.A.S.S.

1. Press and hold the MODE button to enter the “OPTIONS” menu.

2. Use the UP/DOWN toggle buttons to cycle through options until “REQUIRE PIN TO START” appears. Press the MODE button to select.

3. Enter current passcode.

4. Use the UP/DOWN toggle buttons to change the flashing “ON” at bottom of screen to “OFF”.

5. Press the MODE button to re-enter the “OPTIONS” menu. P.A.S.S. is now disabled.

You can exit the “OPTIONS” menu three different ways.

FEATURES AND CONTROLS

• Toggle to “EXIT” and press the MODE button.

• Hold the MODE button for a few seconds.

• Do nothing, allowing the system to automatically revert back to the main screen.

ENGINE ERROR CODES

The error screen displays only when the CHECK ENGINE indicator is on or when it goes on and off during one ignition cycle. Error codes are not stored. When the key is turned OFF, the code and message is lost, but will reappear if the fault reoccurs after restarting the engine.

If the CHECK ENGINE lamp or the EPS lamp illuminates, retrieve the active error codes from the display.

Failure Mode Indicator (FMI)

Suspect Parameter Number (SPN)

Code Count

1. Press and hold the MODE button to enter the settings menu.

2. Press either toggle button to cycle to the “DIAGCODE” option. Press MODE

to select.

3. More than one diagnostic code may be present. Press the toggle UP button

to see if more codes are present. Press MODE to select a code.

NOTICE

If the displayed code is an engine fault code, the CHECK ENGINE lamp will

blink. If the displayed code is an EPS fault code, the EPS lamp will blink.

4. Record the three (3) numbers displayed.

5. Press MODE to exit to the settings menu.

RIDE COMMAND DISPLAY (IF EQUIPPED)

BEFORE YOU RIDE

WARNING

Failure to pay attention to operating your vehicle could result in loss of control,

injury, or death. Always concentrate on riding. Do not enter information while

operating your vehicle. Some features are limited when vehicle is in motion.

Before riding with your new display, do the following:

• Download the Polaris RIDE COMMAND App from the Apple®/Google Play® store and create your personalized account.

• Check your display to ensure you have the appropriate maps and trails visible for your area. To change or update maps/trails see page 76.

• Trails change often, and the trail data file is only considered valid for 90 days after the release date. Please keep your trail data up to date. Download the latest trails at http://ridecommand.polaris.com.

NOTICE

Using the display for an extended period of time while the vehicle’s engine is

off can drain the battery.

VEHICLE-TO-VEHICLE COMMUNICATION (V2V)

IMPORTANT

For applications that use vehicle-to-vehicle (V2V) communication, radio

transmitter IC: 5966A-P001 has been approved by Innovation, Science and

Economic Development Canada (ISED) to operate with the Polaris antenna

(part number 4018713) with gain of 3 dBi. Any antenna that has a gain greater

than 3 dBi is prohibited for use with this device.

DEVICE OPERATING REQUIREMENTS

Phone functionality is dependent on the capabilities of your cell phone.

NOTICE

Some cell phones or operating systems will not work as shown in this manual.

RIDE COMMAND DISPLAY (IF EQUIPPED)

DEVICE COMPLIANCE STATEMENTS

USA RADIO COMPLIANCE

This vehicle contains the following radio equipment or components that contain radio equipment:

COMPONENT COMPONENT ID MANUFACTURER

9200 Series Display RC-7 Polaris Industries Inc.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

CANADA RADIO COMPLIANCE

This vehicle contains the following radio equipment or components that contain radio equipment:

COMPONENT COMPONENT ID MANUFACTURER

9200 Series Display RC-7 Polaris Industries Inc.

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS (s). Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause undesired operation of the device.

IMPORTANT

For applications that use vehicle-to-vehicle (V2V) communication, radio

transmitter IC 5966A-P001 has been approved by Innovation, Science and

Economic Development Canada (ISED) to operate with Polaris antenna (part

number 4018713) with gain of 3 dBi. Any antenna that has a gain greater than

3 dBi is prohibited for use with this device.

RIDE COMMAND DISPLAY (IF EQUIPPED)

EUROPEAN UNION (EU) RADIO COMPLIANCE

This vehicle contains the following radio equipment or components that contain radio equipment:

Component 9200 Series Display

Component ID

Manufacturer Polaris Industries Inc.

*Transmitting Frequency

Max RF Transmitting PWR

*Other transmitting radio frequencies may exist outside of EU markets.

Hereby, Polaris Industries Inc. declares that the above radio equipment is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address:

https://www.polaris.com/en-us/radio-conformity/

2402 - 2480 MHz

RC-7

0.2432 W

RIDE COMMAND DISPLAY (IF EQUIPPED)

OVERVIEW

Ride Command Buttons

Driveline Mode

Widgets

Settings

Icon Bar

Gauge View Mode

Speedometer/Tachometer

Gear Status

RIDE COMMAND BUTTONS

BUTTON DESCRIPTION FUNCTION

Menu Button Press the Menu button to access the

settings. To reboot the display, press and hold for 5 seconds.

Gauge Screen Button

Press the Gauge Screen button to select from available screens.

RIDE COMMAND DISPLAY (IF EQUIPPED)

BUTTON DESCRIPTION FUNCTION

Map Button Press the Map button to access the

map, manage your rides and waypoints, and to see your friends on the map with Group Ride.

Phone Button Press the Phone button to access your

Bluetooth® connected phone, including recent calls, contacts, dialer, and messages.

Audio Button Press the Audio button to access the

Radio, Weather, USB, and connected Bluetooth® music interface

Volume Decrease Button

Volume Increase Button

Press the Volume Decrease button to decrease the volume. Press and hold to mute volume.

Press the Volume Increase button to increase the volume.

RIDE COMMAND DISPLAY (IF EQUIPPED)

PIN ACTIVATED SECURITY SYSTEM (P.A.S.S.) (IF EQUIPPED) — RIDE COMMAND

ENABLE P.A.S.S.

NOTICE

After activating P.A.S.S. for the first time you must power down the vehicle and

allow the electronic control module (ECM) to fully shutdown before restarting.

This may take up to three minutes.

1. Go the settings menu by pressing the Menu button.

2. Select Vehicle Settings from the left toolbar.

3. Select Engine Start Lockout.

4. If this your first time activating P.A.S.S. you will be prompted to enter a new passcode. Enter and verify new passcode.

Please record your passcode.

5. Turn Engine Start Lockout from No to Yes.

6. Turn off the vehicle using the key ignition switch.

NOTICE

If the battery becomes low while the P.A.S.S. system is enabled, the gauge

may show “New Vehicle Detected” after the battery has been recharged/

replaced. Leave the key in the ON position to allow system reconfirmation.

DISABLE P.A.S.S.

1. Go the settings menu by pressing the Menu button.

2. Select Vehicle Settings from the left toolbar.

3. Select Engine Start Lockout.

4. Enter passcode to disable P.A.S.S.

5. Turn Engine Start Lockout from Yes to No.

RIDE COMMAND DISPLAY (IF EQUIPPED)

DRIVELINE MODE

ICON DRIVELINE

MODE

All Wheel Drive (AWD) Lock

All Wheel Drive (AWD) Unlock

DESCRIPTION

Two-Wheel Drive (2WD)

Severe damage to the drive train may occur if the AWD is engaged while the

wheels are spinning. Always allow the wheels to stop spinning before engaging

When the switch is set to 2WD the vehicle is in two-wheel drive at all times.

NOTICE

AWD.

RIDE COMMAND DISPLAY (IF EQUIPPED)

GAUGE SCREENS

Press the Gauge Screen button to toggle between gauge screens. The display comes loaded with two different gauge screens. Additional gauge screens can be added or deleted.

Each gauge screen is customizable and can be set up in the following configurations:

• Four round widgets

• Two round widgets and a list of three data values

• A list of five data values

To customize your gauge screens, press the gear icon located in the lower right corner of the display.

SETTINGS

From the setting menu you can view vehicle information, manage Bluetooth® devices, update display software, and more.

To access the Setting menu, press the Menu button

You can also navigate to the settings menu by pressing the POLARIS logo at the top of the display screen open the Control Panel. From the Control Panel, select the settings tab, then press the All Settings button located in the lower right corner of the display screen.

. This will

RIDE COMMAND DISPLAY (IF EQUIPPED)

GAUGE VIEW MODE

Press q to toggle between the two available gauge view modes, Analog and Digital.

While in the digital gauge view mode, press invert the MPH and RPM units.

DISPLAY MODE

From the Control tab e, select the display mode from the available options y.

The display mode can be set to Day, Night, or AUTO mode.

Day Mode

Night Mode

RIDE COMMAND DISPLAY (IF EQUIPPED)

ICON BAR

ICON DESCRIPTION FUNCTION

Headset Displays icon if headset is connected

Signal Strength Displays current cell signal strength

Wireless Internet Signal Strength

Fuel Level Displays current fuel capacity

Vehicle Direction Displays vehicle direction

Ambient Temperature

Clock Displays current time

Displays current wireless internet signal strength

percentage

Displays ambient temperature

RIDE COMMAND DISPLAY (IF EQUIPPED)

UPDATE SOFTWARE

NOTICE

Before updating the Display, always export your existing rides and waypoints

to a USB drive to avoid losing them.

To update the software, do the following:

ON YOUR PERSONAL COMPUTER

1. Go to ridecommand.polaris.com/update.

2. Log into your account, or create a new account.

3. Using the Vehicle Identification Number (VIN), add your new Polaris vehicle to your Garage.

4. Locate and download the latest software to a USB flash drive (8+ GB).

ON YOUR VEHICLE

1. Connect the USB flash drive to the USB cable and power up your vehicle.

2. On the RIDE COMMAND display, select the Settings menu on your display by pressing the POLARIS icon at the top of the screen.

3. Select General Settings, then Update Software.

4. Select the file you wish to load (use date listed in the file name to determine most recent file).

5. Select Yes to restart display (restart required).

ERROR MESSAGES

If an error occurs while updating your software, perform one or all of the following actions to resolve the issue:

1. Remove and reconnect the USB flash drive securely.

2. Make sure the display files are not inside a folder on the flash drive.

3. Make sure only display files are on the flash drive. Remove any other files if necessary.

4. Try using a different USB flash drive.

RIDE COMMAND DISPLAY (IF EQUIPPED)

UPDATE MAPS

To update the maps on your display, do the following:

1. Go to ridecommand.polaris.com/update and download the map update to a USB flash drive.

2. Insert USB flash drive into the USB port on your vehicle.

3. Press the Update maps in the General Settings.

4. Select the file you want to install by pressing the corresponding down arrow icon.

5. This will update the display’s map which will automatically restart the display once the update is complete. Do not remove the USB flash drive until the display has fully restarted.

USB HARDWARE

SOFTWARE UPDATES

For software update, POLARIS recommends using a SanDisk® or similar USB flash drive with a minimum of 4GB in available memory, formatted using the FAT32 or exFAT® file systems. For best results remove all files from the flash drive before starting the update process.

MAP UPDATES

For Map updates, a 32GB USB drive is required (USB 3.0 drive is highly recommended) USB drive must be formatted to exFAT® before copying the map file onto it.

TRAIL UPDATES

For Trail updates, a 4GB drive formatted to FAT32 can be used.

OPERATION

VEHICLE BREAK-IN

ENGINE AND DRIVETRAIN BREAK-IN

1. Fill the fuel tank with the recommended fuel. See the Refueling section for details. Always exercise extreme caution whenever handling gasoline.

2. Check the oil level. See the Oil Check section for details. Add the recommended oil as needed to maintain the oil level in the safe operating range.

3. Avoid aggressive use of the brakes.

4. Vary throttle positions. Do not operate at sustained idle.

5. Perform regular checks on fluid levels, controls and areas outlined on the daily pre-ride inspection checklist.

6. Carry only light loads.

7. During the break-in period, change both the oil and the filter at 25 hours, one month, or 500 miles, whichever comes first.

8. Check fluid levels of transmission and all gearcases after the first 25 hours of operation and every 50 hours thereafter.

BRAKE SYSTEM BREAK-IN

Apply only moderate braking force for the first 50 stops. Aggressive or overly forceful braking when the brake system is new could damage brake pads and rotors.

OPERATION

PVT BREAK-IN (CLUTCHES / BELT)

A proper break-in of the clutches and drive belt will ensure a longer life and better performance. If a belt fails, always clean any debris from the duct and from the engine compartment.

STANDARD BREAK-IN

Drive at slower speeds for the first 50 miles (80 km) of operation. Carry only light loads. Avoid aggressive acceleration, high-speed operation and prolonged operation at a specific RPM during this period.

SAND / DUNE BREAK-IN

Drive in low gear for the first 5 miles (8 km) of operation. Avoid prolonged low speed operation at high throttle. Avoid aggressive acceleration, high-speed operation and prolonged operation at a specific RPM during this period.

BELT LIFE

To extend belt life, use low gear in the following conditions:

• When hauling or towing heavy cargo

• When consistently operating at speeds less than 35 MPH (56 km/h) in hardpulling terrain, such as mud, rocks or sand/dune environments.

OPERATION

OPERATING GUIDELINES

STARTING THE ENGINE

NOTICE

Operating the vehicle immediately after starting could cause engine damage.

Allow the engine to warm up for several minutes before operating the vehicle.

1. Position the vehicle on a level surface outdoors or in a well- ventilated area.

2. Sit in the driver's seat and fasten the seat belt. Always make sure all cab doors are closed and latched when riding in this vehicle.

3. Place the transmission in PARK.

4. Apply the brakes. Do not press the throttle pedal while starting the engine.

5. Turn the ignition key past the ON/RUN position and release immediately to START. The engine will turn over for a maximum five seconds until the vehicle has started.

6. If the engine does not start within five seconds, return the ignition switch to the OFF position and wait five seconds. Repeat steps 5 and 6 until the engine starts.

7. After starting the engine, wait 10 seconds before applying throttle.

BRAKING

1. Release the throttle pedal completely.

TIP

When the throttle pedal is released completely and engine speed slows to near

idle, the vehicle has no engine braking.

2. Press on the brake pedal evenly and firmly.

3. Practice starting and stopping (using the brakes) until you're familiar with the controls.

OPERATION

DRIVING IN REVERSE

WARNING

Before shifting into reverse, use extra care to make sure the area is clear of

people or obstacles. When it’s safe to proceed, back slowly.

Follow these precautions when operating in reverse:

1. Always check for obstacles or people behind the vehicle.

2. Apply the throttle lightly. Never open the throttle suddenly.

3. Back slowly.

4. Apply the brakes lightly for stopping.

5. Avoid making sharp turns.

STOPPING THE ENGINE AND PARKING THE VEHICLE

WARNING

When leaving the vehicle on an incline is unavoidable, use extra care. Vehicle rollaway can cause serious injury or death. This vehicle can roll whenever the

gear selector is not in the PARK (P) position. Always shift to PARK (P) when

stopping the engine or leaving the vehicle. If leaving the vehicle unattended,

block the rear wheels on the downhill side and keep children, pets, and others

away from the gear selector.

To park the vehicle:

1. Stop the vehicle on a level surface.

2. Place the transmission in PARK (P). This vehicle can roll whenever the transmission is not in the PARK (P) position.

3. Stop the engine.

4. Engage the park brake (if equipped).

5. Remove the ignition key to prevent unauthorized use.

EMISSION CONTROL SYSTEMS

NOISE EMISSION CONTROL SYSTEM

Do not modify the engine, intake or exhaust components, as doing so may affect compliance with U.S.A. EPA noise control requirements (40 CFR 205) and local noise level requirements.

OPERATION ON PUBLIC LANDS IN THE U.S.A.

Your POLARIS vehicle has a spark arrester that was tested and qualified to be in accordance with the USFS standard 5100-1C. Federal law requires that this spark arrester be installed and functional when the vehicle is operated on public lands.

Operation of off-road vehicles on public lands in the U.S.A. is regulated by 43 CFR 420. Violations are subject to monetary penalties. Federal regulations can be viewed online at www.ecfr.gov..

CRANKCASE EMISSION CONTROL SYSTEM

This engine is equipped with a closed crankcase system. Blow-by gases are forced back to the combustion chamber by the intake system. All exhaust gases exit through the exhaust system.

EXHAUST EMISSION CONTROL SYSTEM

Exhaust emissions are controlled by engine design. An electronic fuel injection (EFI) system controls fuel delivery. The engine and EFI components are set at the factory for optimal performance and are not adjustable.

The emissions label is located on the left front frame of the vehicle.

ELECTROMAGNETIC INTERFERENCE

This spark ignition system complies with Canadian ICES-002.

This vehicle complies with EMC requirements of UN ECE Regulation 10 and European directives 97/24/EC and 2004/108/EC.

Non-ionizing Radiation: This vehicle emits some electromagnetic energy. People with active or non-active implantable medical devices (such as heart monitoring or controlling devices) should review the limitations of their device and the applicable electromagnetic standards and directives that apply to this vehicle.

MAINTENANCE

PERIODIC MAINTENANCE

WARNING

Do not attempt any maintenance procedures that are not described in this

manual or that you are not comfortable performing. Some maintenance

procedures are more extensive and may require special training, tools, and

equipment. An authorized POLARIS dealer can perform any service that may

be necessary for your vehicle.

WARNING

Be sure to properly reinstall all components that were removed during any

maintenance. For example, some parts are made and positioned to deflect

heat, and failing to reinstall heat shields properly can lead to a fire.

WARNING

Hot parts can cause burns. To avoid burns, do not touch hot components or

attempt maintenance before allowing to cool. Surfaces that could be hot during

and after operation can include components of the:

• Engine and exhaust

• Brakes

• Shock absorbers

WARNING

Before service or maintenance, make sure the transmission is in Park and the

engine is off with the key removed. Moving parts can contact body parts or

clothing. Running the engine while servicing can lead to serious injury, electric

shock, burns, fire, carbon monoxide poisoning, and death.

WARNING

Do not run engine with any covers removed. Contact with exposed belt or

moving parts can cause serious injury.

MAINTENANCE

WARNING

Vehicle fluids such as oil or brake fluid can be hazardous. Wear gloves and

avoid skin contact. Always follow the handling and disposal instructions

provided by the fluid manufacturer.

SEVERE USE DEFINITION

Vehicles subjected to heavy or severe use patterns must be inspected and serviced more frequently. Vehicles subjected to severe use must be serviced at 50% of the stated interval. Examples of severe use include:

• Frequent immersion in mud, water, or sand

• Prolonged low speed, heavy load operation

• Extended idle

• Sustained high-RPM use

• Frequent short trip operation in cold weather (engine frequently does not

operate long enough to reach full operating temperature)

IMPORTANT

Pay special attention to the oil level. A rise in oil level during cold weather can

indicate contaminants collecting in the oil sump or crankcase. Change oil

immediately if the oil level begins to rise. Monitor the oil level, and if it

continues to rise, discontinue use and determine the cause. Your POLARIS

dealer or other authorized person can assist.

POLARIS MAINTENANCE SCHEDULE

The intervals shown are based on vehicles operated under normal conditions.

Each interval is given in hours and miles (kilometers). Items should be serviced at whichever interval comes first following the Initial Break-In Service.

Continue to reference the following maintenance schedules at the given intervals as hours and miles (kilometers) increase on the vehicle.

MAINTENANCE

Vehicles subjected to severe use must be serviced at 50% of the stated interval. Examples of Severe Use: Frequent immersion in mud, water, or sand, constant high RPM use, prolonged low-speed heavy load operation, extended idle, and short trip cold weather operation.

INITIAL BREAK-IN SERVICE

FIRST 25 HOURS / 1 MONTH

Inspect air filter; replace as necessary. Ensure

Engine Air Filter

Cooling System

proper installation of filter and airbox cover. Inspect ducts and screens; clean as necessary.

Fluid level inspection; inspect for fluid leaks; add coolant if needed. Inspect coolant strength seasonally; pressure test system yearly.

General Lubrication

Shift Cable / Linkage Inspect; adjust as needed.

Parking Brake (if applicable)*

Battery

Engine Oil and Filter Change the engine oil and filter.

Front Gearcase Fluid

Rear Gearcase Fluid

Transmission Fluid

Locate all applicable fittings and grease.

Inspect; adjust as needed.

Check terminals; terminals should be tight and free of corrosion. Clean, test, and replace as necessary.

Initial fluid level inspection; add lubricant if needed.

Initial fluid level inspection; inspect for fluid leaks; add lubricant if needed.

Spark Arrestor Inspect; clean as needed.

The break-in period consists of the first 25 hours of operation. Careful treatment of a new engine and drive components will result in more efficient performance and longer life for these components. The items outlined in this service interval only need to be performed at the first 25 hours of operation. They do not need to be performed every 25 hours.

* It is recommended to have an authorized Polaris dealer perform these services.

MAINTENANCE

EVERY 25 HOURS / 500 MILES (1600 KM) OR YEARLY FOLLOWING

INITIAL BREAK-IN SERVICE

Inspect air filter; replace as necessary. Ensure

Engine Air Filter

Battery

Brake System

proper installation of filter and airbox cover. Inspect ducts and screens; clean as necessary.

Check terminals; terminals should be tight and free of corrosion. Clean, test, and replace as necessary.

Fluid level inspection; inspect for fluid leaks; add lubricant if needed. Inspect brake pad wear. Inspect hoses for damage.

General Lubrication

Radiator

Tires

Shift Cable/Linkage Inspect; adjust as needed.

* Have an authorized Polaris dealer or other qualified person perform these services.

Locate all applicable fittings and grease.

Inspect; Clean external surfaces.

Inspect; Adjust pressure level as needed; Inspect wear and replace as needed.

MAINTENANCE

EVERY 50 HOURS / 1000 MILES (3200 KM) OR YEARLY FOLLOWING

INITIAL BREAK-IN SERVICE

Inspect air filter; replace as necessary. Ensure

Engine Air Filter

Battery

Brake System

proper installation of filter and airbox cover. Inspect ducts and screens; clean as necessary.

Check terminals; terminals should be tight and free of corrosion. Clean, test, and replace as necessary.

Fluid level inspection; inspect for fluid leaks; add lubricant if needed. Inspect brake pad wear. Inspect hoses for damage.

General Lubrication

Radiator

Tires

Engine Oil and Filter Change the engine oil and filter.

Spark Plug Inspect; replace as needed.

Wiring Inspect for wear, routing, and retention.

Front Gearcase Fluid

Rear Gearcase Fluid

Transmission Fluid

Drive Belt

Locate all applicable fittings and grease.

Inspect; Clean external surfaces.

Inspect; Adjust pressure level as needed; Inspect wear and replace as needed.

Change fluid.

Initial fluid level inspection; inspect for fluid leaks; add lubricant if needed.

Inspect; replace as needed.

Clutches

Spark Arrestor Inspect; clean as needed.

Suspension Components / Alignment*

Inspect weights, bushings, rollers, wearable parts; clean; replace worn parts as needed.

Inspect front and rear suspension bushings, and ball joints for loose or worn components; replace as needed. Inspect shock absorbers for leaks or damage.

MAINTENANCE

EVERY 50 HOURS / 1000 MILES (3200 KM) OR YEARLY FOLLOWING

INITIAL BREAK-IN SERVICE

Fluid level inspection; inspect for fluid leaks;

Cooling System

Wheel Bearings Inspect; replace as needed.

add coolant if needed. Inspect coolant strength seasonally; pressure test system yearly.

Parking Brake (if applicable)*

Fuel System*

Intake Ducts

Shift Cable/Linkage Inspect; adjust as needed.

Wrap Under Suspension and Steering Components/ Alignment

* Have an authorized Polaris dealer or other qualified person perform these services.

Inspect; adjust as needed.

Cycle key to pressurize fuel pump; check for leaks at fuel system connections, check for leaks at fill cap.

Inspect ducts for proper sealing / air leaks.

Inspect; replace as needed.

MAINTENANCE

ADDITIONAL MAINTENANCE INTERVALS

Every 2000 miles (3200KM) / 24 months / 2 years / 100 hours

Brake Fluid

Change fluid.

Every 2500 miles (4000KM)

Every 5000 miles (8900KM) / 60 months / 5 years

Every 10,000 miles (16,000KM) / 500 hours

* Have an authorized Polaris dealer or other qualified person perform these services.

Shock Absorbers*

Coolant

Alternator Belt

Spark Plugs Replace.

Valve Clearance*

Replace or rebuild (if applicable).

Change fluid.

Replace.

Inspect; adjust as needed.

MAINTENANCE

LUBRICATION RECOMMENDATIONS

Check and lubricate all components at the intervals outlined in the Periodic Maintenance Chart section, or more often under severe use, such as wet or dusty conditions. Items not listed in the chart should be lubricated at the general lubrication interval.

ITEM LUBE METHOD

Engine Oil PS-4 5W-50 4-Cycle

Oil and PS-4 Extreme 0W-50 4-Cycle Oil

Brake Fluid DOT 4 Brake Fluid Maintain level between fill

Transmission Oil (Main Gearcase)

Front Gearcase Fluid 80W-140 Angle Drive

Prop Shaft Spline Grease Grease the fitting until fresh

Rear Drive Gearcase 80W-140 Angle Drive

AGL Gearcase Lubricant & Transmission Fluid

Fluid

See page 93.

lines. See page 120.

See page 96.

See page 97.

grease is seen coming from the joint. Wipe away excess to prevent dirt/debris contamination.

See page 98.

Rear Propshaft Grease Fitting

MAINTENANCE

ENGINE OIL

OIL RECOMMENDATIONS

NOTICE

Vehicle operation with insufficient, deteriorated, or contaminated engine oil will

cause accelerated wear.

AMBIENT TEMPERATURE RANGE RECOMMENDED OIL

-35 °F to +100 °F

(-37 °C) to (+38 °C)

-45 °F to +130 °F

(-43 °C) to (+54 °C)

Oil may need to be changed more frequently if POLARIS oil is not used. Do not use automotive oil. Follow the manufacturer's recommendations for ambient temperature operation. Part numbers can be found in the POLARIS Products chapter.

NOTICE

Mixing brands or using a non-recommended oil may cause serious engine

damage. Always use the recommended oil. Never substitute or mix oil brands.

Always check and change the oil at the intervals outlined in the Periodic Maintenance Chart. Always use the recommended engine oil.

PS-4 5W-50 4-Cycle Oil

PS-4 Extreme

0W-50 4-Cycle Oil

MAINTENANCE

OIL CHECK

Always check the oil when the engine is cold and on a level surface. If the engine is hot when the oil is checked, the level will appear to be overfull.

Access the oil check dipstick fill cap w by removing the cargo box. See the Service Access Panels section for details.

1. Position the vehicle on a level surface.

2. Place the transmission in PARK.

3. Start the engine. Allow the engine to idle for two-to-three (2-3) minutes.

through the right rear wheel well. Access the oil

4. Stop the engine. Wait three (3) minutes before checking the oil level. This allows the oil to settle to the bottom of the crankcase. Do not check the oil

level immediately after stopping the engine.

5. Remove the dipstick. Wipe it dry with a clean cloth.

6. Reinstall the dipstick completely. Remove the dipstick and check the oil level.

7. Remove the oil fill cap to add the recommended oil as needed. Maintain the oil level between the minimum and maximum marks on the dipstick. Do not overfill.

8. Reinstall the fill cap. Reinstall the dipstick.

MAINTENANCE

OIL AND FILTER CHANGE

WARNING

Spilled oil left on engine components or in the engine area may pose a fire

hazard. Use shop rags to clean any spilled oil. If needed, use a non-flammable

solvent on the rag to aid the cleaning process. Do not use any device such as

pressurized water or air as this may disperse the oil onto engine components

and could pose a fire hazard.

CAUTION

Engine oil is hot after use and can cause burns to skin.

Always change the oil and filter at the intervals outlined in the Periodic Maintenance Interval Chart.

1. Position the vehicle on a level surface. Place the transmission in PARK.

2. Allow engine to cool down before draining oil.

Place a drain pan under the engine crankcase and remove the drain plug using a 6 mm Allen wrench..

4. Access the oil filter through the driver’s side rear wheel well.

NOTICE

Wait two (2) minutes to allow oil to drain back to the sump.

MAINTENANCE

5. Place shop rags under the filter to catch any spilled oil during removal. Using the your hand, or an Oil Filter Wrench, turn the oil filter counter-clockwise until oil starts to drain through the slot in the skid plate. Allow the oil to stop draining before removing the filter completely. Tip the open end of the oil filter up to minimize oil spill. Ensure all shop rags are removed after cleaning up any spilled oil.

6. Clean the filter sealing surface on the engine crankcase with a clean rag and ensure the original oil filter o-ring is not stuck to the crankcase.

7. Lubricate the o-ring on the new oil filter with a film of clean engine oil. Check to make sure the o-ring is in good condition. Tighten to specification.

TORQUE

Oil Filter:

Turn by hand until filter O-ring contacts sealing surface, then turn an

additional 3/4 turn.

8. Inspect the sealing washer on the drain plug for burrs or nicks. Replace the washer if it is damaged.

9. Reinstall the engine crankcase drain plug. Torque drain plug to specification.

TORQUE

Engine Oil Drain Plug:

12 ft-lbs (16 Nm)

10. Remove the cargo box. Add engine oil through the oil fill cap engine valve cover.

11. Fill the engine to the recommended specification. See the Specifications chapter.

located on top of the

12. Start engine and allow it to idle for two-to-three (2-3) minutes.

13. Stop the engine and inspect for leaks. Wait at least three (3) minutes before removing the oil dipstick.

MAINTENANCE

14. Remove the dipstick e and wipe it dry with a clean rag.

15. Reinstall the dipstick to fully seat it. Make certain the dipstick is inserted all the way down to ensure an accurate reading.

16. Remove the dipstick and check the oil level.

17. Add the recommended oil as necessary to bring the oil level within the SAFE range (between the holes) on the dipstick. Do NOT overfill.

IMPORTANT

A rising oil level between checks during cold weather operation can indicate

contaminants such as gas or moisture collecting in the crankcase. If the oil

level is over the upper mark, change the oil immediately.

18. When finished, reinstall dipstick.

19. Reinstall the cargo box.

20. Dispose of used oil, filter, and rags properly.

MAINTENANCE

TRANSMISSION

TRANSMISSION (MAIN GEARCASE)

Always check and change the fluid at the intervals outlined in the Periodic Maintenance Chart section. Refer to the Gearcase Specifications Chart for recommended lubricants, capacities and torque specifications.

FLUID CHECK

The fill plug q is located on the right side of the gearcase. Maintain the fluid level at the bottom of the fill plug hole.

1. Position the vehicle on a level surface.

2. Remove the fill plug using a 8 mm Allen wrench..

3. Check the fluid level.

4. If necessary, add the recommended fluid to the bottom of the fill plug hole. Do not overfill.

5. Reinstall the fill plug. Torque to specification.

FLUID CHANGE

The drain plug w is located on the bottom of the gearcase. Access the drain plug through the drain hole in the skid plate.

1. Remove the fill plug.

2. Place a drain pan under the drain plug using a 8 mm Allen wrench.

3. Remove the drain plug. Allow the fluid to drain completely.

4. Clean the drain plug.

5. Reinstall the drain plug. Torque to specification (listed in the Gearcase Specification Chart of this manual).

MAINTENANCE

6. Add the recommended fluid (listed in the Gearcase Specification Chart) to the bottom of the fill plug hole. Do not overfill.

7. Reinstall the fill plug. Torque to specification (listed in the Gearcase Specification Chart).

8. Check for leaks. Discard used fluid properly.

FRONT GEARCASE

FLUID CHECK

The fill plug q is located on the bottom right side of the front drive unit. Maintain recommended fluid volume (listed in the Gearcase Specification Chart).

1. Position the vehicle on a level surface.

2. Remove the fill plug using an 8 mm Allen wrench.

3. Check the fluid level.

4. Add the recommended fluid (listed in the Gearcase Specification Chart). Do not overfill.

5. Reinstall the fill plug. Torque to specification (listed in the Gearcase Specification Chart).

MAINTENANCE

FLUID CHANGE

The front drive drain plug w is located on the bottom of the gearcase.

1. Remove the fill plug using an 8 mm Allen wrench.

2. Place a drain pan under the drain plug.

3. Remove the drain plug. Allow the fluid to drain completely.

4. Clean the drain plug.

5. Reinstall the drain plug. Torque to specification (listed in the Gearcase Specification Chart).

6. Add the recommended fluid (listed in the Gearcase Specification Chart). Do not overfill.

7. Reinstall the fill plug. Torque to specification (listed in the Gearcase Specification Chart).

8. Check for leaks. Discard used fluid properly and clean any excess oil residue.

REAR GEARCASE

FLUID CHECK

The fill plug q is located on the bottom right side of the rear gearcase. Maintain recommended fluid volume.

Polaris RZR Pro R (2022) Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual