Please take a few moments to carefully read through this
manual. Correct maintenance and operation of this machine will
provide the best possible performance from your POLAR product.
• Position on a flat, stable surface.
• A service agent/qualified technician should carry out
installation and any repairs if required. Do not remove any
components or service panels on this product.
• Consult Local and National Standards to comply with the
following:
- Health and Safety at Work Legislation
- BS EN Codes of Practice
- Fire Precautions
- IEE Wiring Regulations
- Building Regulations
• DO NOT use jet/pressure washers to clean the appliance.
• DO NOT use the appliance outside.
• DO NOT use this appliance to store medical supplies.
• DO NOT allow oil or fat to come into contact with the plastic
components or door seal. Clean immediately if contact occurs.
• DO NOT store products on top of the appliance.
• Bottles that contain a high percentage of alcohol must be
sealed and placed vertically in the refrigerator.
• Always carry, store and handle the appliance in a vertical
position and move by holding the base of the appliance.
• Always switch off and disconnect the power supply to the unit
before cleaning.
• Keep all packaging away from children. Dispose of the packaging
in accordance with the regulations of local authorities.
• Children should be supervised to ensure that they do not play
with the appliance.
• POLAR recommend that this product is connected to a circuit
protected by an appropriate RCD (Residual Current Device).
2
Page 3
EN
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience or knowledge, unless they have been
given supervision or instruction concerning the use of the
appliance by a person responsible for their safety.
• POLAR recommend that this appliance should be periodically
tested (at least annually) by a Competent Person. Testing
should include, but not be limited to: Visual Inspection,
Polarity Test, Earth Continuity, Insulation Continuity and
Functional Testing.
Caution: Risk of Fire
• Do not store explosive substances such as aerosol cans with a
flammable propellant in this appliance.
Warning: Keep all ventilation openings clear of
obstruction. Unit should not be boxed in without
adequate ventilation.
• Warning: Do not use mechanical devices or other means
to accelerate the defrosting process, other than those
recommended by the manufacturer.
• Warning: Do not damage the refrigerant circuit.
• Warning: Do not use electrical appliances inside the food
storage compartments of the appliance.
POLAR prides itself on quality and service, ensuring that at the time of unpacking the contents are
supplied fully functional and free of damage.
Should you find any damage as a result of transit, please contact your POLAR dealer immediately.
• Instruction manual
3
Page 4
EN
Installation
Not for use in vans or trailers, food trucks
or similar vehicles.
If the unit has not been stored or moved in
an upright position, let it stand upright for
approximately 12 hours before operation.
If in doubt allow to stand.
1. Remove the appliance from the packaging.
Make sure that all protective plastic film and
coatings are thoroughly removed from all
surfaces.
2. To optimize performance and longevity, ensure
a minimum clearance of 2.5cm is maintained
between the unit and walls and other objects,
with a minimum 20cm clearance on the top.
NEVER LOCATE NEXT TO A HEAT SOURCE.
Note: Before using the appliance
for the first time, clean the
shelves and interior with soapy
water then dry well.
Operation
Control Panel
The controlpanel is located below the doors on the
rear of the appliance.
Manual Defrost
Press and hold the button for 6 seconds to begin
automatic defrost. The defrost light illuminates.
The defrost cycle will end automatically.
Cleaning, Care &
Maintenance
1. Switch off and disconnect from the power
supply before cleaning.
2. The doors can be removed for ease of
cleaning.
3. Clean the interior of the appliance as often as
possible.
4. Do not use abrasive cleaning agents. These
can leave harmful residues.
5. Clean the door seal with warm soapy water.
6. Always wipe dry after cleaning.
Refrigerating tips:
• Condensation and ice will form with frequent
and prolonged opening of the doors.
• Operating outside of the recommend
temperature range and placing next to a heat
source will also increase the amount of ice
and internal/external condensation. If external
condensation occurs wipe the surface down
with a cloth.
• Excessive ice will result in longer running times
that will increase energy consumption and
increase the deterioration of components.
• If the gasket or seal is damaged or deformed,
energy consumption will increase. To restore
efficiency, replace gasket.
Turn On
1. Close the doors of the appliance
2. Connect the appliance to a mains power
supply.
3. Press the button to turn the light On or Off
as required.
.
Setting the Operating Temperature
1. Press the SET button. The display will flash.
2. Press the or buttons to display the
required temperature.
3. Press the SET button to store the temperature.
4
Replacing the Interior Lamp
Call your POLAR dealer or a qualified electrician,
the Lamp Assembly is available to purchase as a
spare part.
Cleaning the Condenser
Periodically cleaning the condenser can extend the
life of the appliance. POLAR recommend that a
POLAR agent or qualified technician should clean
the condenser.
Failure to clean the condenser will increase energy
consumption, reduce the performance and life
of your Polar unit, and thus may invalidate your
warranty.
Page 5
EN
Troubleshooting
A qualified technician must carry out repairs if required.
FaultProbable CauseSolution
The appliance is not
working
The appliance
turns on, but the
temperature is too
high/ low
The appliance is
leaking water
The appliance is
unusually loud
The display lamp
does not illuminate
Door does not shutDirt/obstacle in runnersClean runners
Error code EE4
The unit is not switched onCheck the unit is plugged in correctly and
Plug or lead are damagedReplace plug or lead
Fuse in the plug has blownReplace the fuse
Mains power supply faultCheck mains power supply
Too much ice on the condenserDefrost the appliance
Condenser blocked with dustClean the condenser
Doors are not shut properlyCheck doors are shut and seals are not
Appliance is located near a heat
source, in the direct sunlight or
air flow to the condenser is being
interrupted
Ambient temperature is too highIncrease ventilation or move appliance to a
Unsuitable foodstuffs are being
stored in the appliance
Appliance is overloadedReduce the amount of food stored in the
The appliance is not properly
levelled
Loose screw/nutCheck and tighten all nuts and screws
The appliance has not been installed
in a level or stable position
Lamp needs replacingReplace the lamp
Light not turned onEnsure Light button has been pressed
• Restricted Airflow
• Blocked Condenser
switched on
damaged
Move the refrigerator to a more suitable
location
cooler position
Remove any excessive hot foodstuffs or
blockages to fan
appliance
Adjust the screw feet to level the appliance
(if applicable)
Check installation position and change if
necessary
properly
• Increase airflow
• Clean the condenser
5
Page 6
EN
Technical Specifications
Note: Due to our continuous improvement process, the product specifications are subject to change
without notice.
Power
Model Voltage
GP292220-
GP2912001.42°C ~ 12°C108160R600a
PG0031601.42°C ~ 12°C83120R600a
PG0042001.42°C ~ 12°C106160R600a
240V~
50Hz
Current
(W)
1601.42°C ~ 12°C83120R600a
(A)
Temperature
Range
Net
usable
capacity
(Ltr)
Gross
Volume
(litres)
Refrigerant
type /
weight (kg)
(0.050kg)
(0.065kg)
(0.050kg)
(0.065kg)
Dimensions
H x W x D
mm
686 x 696 x
568
686 x 874 x
568
686 x 702 x
568
686 x 880 x
568
Weight
(kg)
57
66
55
63.5
Note: For optimal product performance and efficiency, please ensure to mind the net usable capacity (load
limit) when filling.
Impact of temperature settings on food waste:
In order to reduce food waste from decomposition or dehydration, this appliance should be operated in
its designated operating range.
Optimum temperature for food storage: 6°C
To order spare parts please contact your Polar Stockist:
https://www.polar-refrigerator.com/stockist
Minimum period of spares parts to be available:
Door handles, door hinges, knobs, dials and buttons, door gaskets, peripheral trays, baskets and racks
for storage, as appropriate to the appliance, will be made available to both end users and professional
users for a minimum of eight years after the last unit of the model is placed on the market. A broader
selection of parts will also be made available to Professional users for this period.
Model information can be found on the product database:
Model information can be found on the product:
The Model Identifier can usually be found on the inside wall and on the reverse of the unit.
Note: Polar offers a 2 year minimum warranty, please contact the authorised representative for more
details.
6
Page 7
EN
Electrical Wiring
POLAR appliances are supplied with a 3 pin BS1363 plug and lead.
The plug is to be connected to a suitable mains socket.
POLAR appliances are wired as follows:
• Live wire (coloured brown) to terminal marked L
• Neutral wire (coloured blue) to terminal marked N
• Earth wire (coloured green/yellow) to terminal marked E
This appliance must be earthed.
If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency
disconnection being required they must be readily accessible.
Disposal
EU regulations require refrigeration product to be disposed of by specialist companies who remove or
recycle all gasses, metal and plastic components.
Consult your local waste collection authority regarding disposal of your appliance. Local authorities are
not obliged to dispose of commercial refrigeration equipment but may be able to offer advice on how to
dispose of the equipment locally.
Alternatively call thePOLAR helpline for details of national disposal companies within the EU.
Compliance
Dispose of depleted batteries in accordance with local regulations, within the EC there are nominated
disposal points for batteries.
The WEEE logoon this product or its documentation indicates that the product must
not be disposed of as household waste. To help prevent possible harm to human
health and/or the environment, the product must be disposed of in an approved and
environmentally safe recycling process. For further information on how to dispose of
thisproduct correctly, contact the product supplier, or the local authority responsible for
waste disposal in your area.
POLAR parts have undergone strict product testing in order to comply with
regulatory standards and specifications set by international, independent,
and federal authorities.
POLAR products have been approved to carry the following symbol:
All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording or otherwise, without the prior written permission of POLAR.
Every effort is made to ensure all details are correct at the time of going to press, however, POLAR reserve the right to
change specifications without notice.
7
Page 8
NL
Veiligheidstips
Neem de tijd en lees deze handleiding aandachtig door. Een
correct gebruik en onderhoud van deze machine waarborgt de
beste prestatie van uw POLAR product.
• Plaatsen op een vlakke en stabiele ondergrond.
• De installatie en eventuele reparaties dienen door een
servicemonteur/vakman uitgevoerd te worden. Verwijder geen
onderdelen of servicepanelen van dit product.
• Raadpleeg en volg de plaatselijke en nationale regelgeving op
m.b.t. tot het volgende:
- Wetgeving inzake gezondheid en veiligheid op het werk
- NEN-praktijkrichtlijnen
- Brandpreventie
- IEE-bedradingsvoorschriften
- Bouwvoorschriften
• Dit apparaat NIET buitenshuis gebruiken.
• Gebruik het product NIET voor het opbergen van medische
producten.
• Laat NIET toe dat olie of vet in contact komt met plastic
componenten of deurafdichtingen. Onmiddellijk reinigen indien
dit wel gebeurt.
• GÉÉN producten bovenop het apparaat neerzetten.
• Flessen met en hoog alcoholpercentage moet goed worden
gesloten en verticaal in de koelkast worden bewaard.
• Dit product altijd in een verticale positie vervoeren, opbergen
en gebruiken. Het product verplaatsen door aan de onderkant
op te tillen.
• Alvorens dit apparaat te reinigen dient men altijd de
stroomvoorziening uit te schakelen.
• Laat verpakkingsmateriaal niet binnen handbereik van kinderen.
Verpakkingsmateriaal in overeenstemming met de regelgeving
van de plaatselijke overheden als afval laten verwerken.
• Men dient er toezicht op te houden dat kinderen niet met het
apparaat spelen.
8
Page 9
NL
• Dit product NIET reinigen met spuit-/drukreinigers.
• Dit apparaat is niet bedoeld voor gebruik door personen met
lichamelijke, zintuigijike of mentale beperkingen (inclusief
kinderen) of met gebrek aan ervaring of kennis tenzij zij hierin
worden begeleid of zijn opgeleid in het gebruik van het apparaat
door een persoon, die verantwoodelijk is voor hun veiligheid.
• POLAR beveelt aan dat dit apparaat periodiek (minstens
jaarlijks) door een bevoegde persoon wordt getest. Tests
moeten omvatten, maar zijn niet beperkt tot: visuele inspectie,
polariteit, aardings continuïteit, isolatie continuïteit en
functionele test.
Voorzichtig: brandgevaar
• Zet geen explosieve stoffen niet opslaan: zoals spuitbussen
met een ontvlambare drijfgas in dit apparaat.
Waarschuwing: Hou alle ventilatieopeningen vrij
van obstakels. Het apparaat mag niet ingesloten
worden zonder adequate ventilatie.
• Waarschuwing: mechanische apparaten of andere
middelen niet gebruiken om het ontdooien te versnellen, met
uitzondering van de fabrikant aanbevolen die door.
• Waarschuwing: het koelcircuit niet beschadigen.
• Waarschuwing: Gebruik geen elektrische apparaten binnen
het voedsel opbergvakken van het apparaat.
POLAR is trots op de haar productkwaliteit en dienstverlening en controleert de inhoud van de
verpakkingen, tijdens de verpakkingsfase, op functioneren en schade.
Mocht uw product door transport zijn beschadigd, neem dan onmiddellijk contact op met uw POLAR dealer.
• Handleiding
9
Page 10
NL
Installatie
Opmerking: Niet voor gebruik in
bestelwagens of aanhangwagens,
foodtrucks of soortgelijke voertuigen.
Opmerking: indien het apparaat niet in
een rechtopstaande positie is opgeslagen
of vervoerd, dient men het product 12 uur
vóór gebruik in de rechtopstaande positie te
plaatsen. Bij twijfel dient men het product
in een rechtopstaande positie te plaatsen.
Werktemperatuur instellen
1. Druk op de SET knop. Het display knippert.
2. Druk op de of knoppen om de vereiste
temperatuur weer te geven.
3. Druk op de SET knop om de temperatuurwaarde
op te slaan.
Handmatig ontdooien
De knop indrukken en gedurende 6 seconden
ingedrukt houden om automatische ontdooiing te
starten. Het ontdooiingslampje gaat aan.
De ontdooicyclus eindigt automatisch.
1. Haal het product uit de verpakking. Zorg ervoor
dat u de beschermingsfolie en -lagen van alle
oppervlakken heeft verwijderd.
2. Om de prestaties en levensduur te
optimaliseren, dient u ervoor te zorgen dat
er minimaal 2,5 cm afstand wordt gehouden
tussen de unit en muren en andere objecten,
met een minimale vrije ruimte van 20 cm aan
de bovenkant. PLAATS NOOIT NAAST EEN
WARMTEBRON.
Opmerking: Voor het eerste
gebruik van dit product dient
u de lades en de binnenzijde
met zeepwater te reinigen, en
daarna goed droogmaken met
een droogdoek.
Werking
Bedieningspaneel
Het bedieningspaneel bevindt zich onder de deuren
aan de achterzijde van het apparaat.
Reiniging, zorg &
onderhoud
1. Alvorens het apparaat te reinigen dient
men stroomstekker uit het stopcontact te
halen.
2. Voor extra reinigingsgemak is het mogelijk de
deuren te verwijderen.
3. Reinig zo vaak mogelijk de binnenkant van het
apparaat.
4. Gebruik géén bijtende reinigingsmiddelen.
Dergelijke middelen kunnen schadelijke resten
achterlaten.
5. Reinig de deurdichting met warm zeepwater.
6. Na reiniging altijd droogmaken.
Koeltips:
• Bij veelvuldig en langdurig openen van de
deuren zal zich condens en ijs vormen.
• Gebruik buiten het aanbevolen
temperatuurbereik en plaatsing naast een
warmtebron zal ook de hoeveelheid ijs en
interne/externe condensatie doen toenemen.
In geval van externe condensatie kunt u het
oppervlak afvegen met een doek.
• Te veel ijs leidt tot langere bedrijfstijden,
waardoor het energieverbruik toeneemt en de
onderdelen slechter worden.
• Als de pakking of afdichting beschadigd of
vervormd is, zal het energieverbruik toenemen.
Vervang de pakking om de efficiëntie te herstellen.
Inschakelen
1. Sluit de deuren van het apparaat.
2. Sluit het apparaat aan op de stroomvoorziening.
3. Druk op de knop om de verlichting naar
wens aan of uit te schakelen.
10
Verlichtingslamp vervangen
Neem contact op met uw POLAR dealer of een
vakkundige elektricien. De lampeenheid is als een
reserveonderdeel aan te schaffen.
Page 11
NL
Reiniging van de condensor
Periodieke reiniging van de condensor kan de technische levensduur van het apparaat verlengen. POLAR
raadt u aan om de reiniging van de condensor door een POLAR technicus of een bevoegde vaktechnicus
te laten uitvoeren.
Het niet reinigen van de condensator zal het energieverbruik verhogen, de prestaties en de levensduur
van uw Polar-eenheid, beperken en hierdoor uw garantie ongeldig zal maken.
Oplossen van problemen
Indien nodig moet een gekwalificeerde technicus reparaties uitvoeren.
ProbleemMogelijke oorzaakHandeling
Het apparaat werkt
niet
Het apparaat
staat aan maar de
temperatuur is te
hoog/laag
Het product lekt
water
Het product maakt
ongebruikelijk veel
lawaai
De displaylamp gaat
niet aan
Deur sluit nietVuil/obstakel in de geleidersReinig de geleiders
Fout code EE4
Het apparaat staat uitControleer of de stroomkabel van het
Steker en kabel zijn beschadigdVervang stekker of kabel
Storing netvoedingControleer netvoeding
Teveel ijs in de Condensor wordt
geblokkeerd door stof
Condensor wordt geblokkeerd door
stof
Deuren niet goed geslotenControleer of de deuren goed dicht zijn en
Hetapparaat bevindt zich in de
nabijheid van een warmtebron,
in het directe zonlicht of de
luchtstroom naar de condensator is
onderbroken
Omgevingstemperatuur is te hoogVerbeter de ventilatie of verplaats het
Ongeschikte levensmiddelen worden
in het apparaat bewaard
Het product wordt overbelast.Verminder de hoeveelheid opgeslagen
Het product staat niet waterpasPas de verstelbare poten aan om het
Schroef/moer losAlle moeren en schroeven controleren en
Het apparaat is niet op een effen of
stabiele ondergrond geplaatst
Lamp vervangenVervang de lamp
Zet het licht aanControleer of de verlichtingsknop goed is
• Beperkte luchtstroom
• Geblokkeerde condensor
apparaat is aangesloten en of het apparaat
is ingeschakeld
Ontdooi het apparaat
Reinig de condensor
of afdichtingen niet beschadigd zijn
Verplaats de koelkast naar een geschiktere
locatie
product naar een koelere locatie
Verwijder alle overbodige warme
levensmiddelen of deblokkeer de ventilator
voedsel in het product
product te nivelleren (indien nodig)
goed vast zetten
Installatielocatie controleren en indien
nodig veranderen
ingedrukty
• Verhoog de luchtstroom
• Reinig de condensor
11
Page 12
NL
Technische specificaties
Opmerking: Vanwege ons voortdurende verbeteringsproces, kunnen de productspecificaties zonder
voorafgaande kennisgeving worden gewijzigd.
ModelVoltage
GP292220-
GP2912001,42°C ~ 12°C108160R600a
PG0031601,42°C ~ 12°C83120R600a
PG0042001,42°C ~ 12°C106160R600a
240V~
50Hz
Vermo-
Stroom
gen
(W)
1601,42°C ~ 12°C83120R600a
(A)
Temperatuur-
bereik
Net
bruikbare
capaciteit
(Ltr)
Bruto
volume
(Ltr)
Type de
réfrigérant
/ poids
(kg)
(0,050kg)
(0,065kg)
(0,050kg)
(0,065kg)
Afmetingen
h x b x d mm
686 x 696 x
568
686 x 874 x
568
686 x 702 x
568
686 x 880 x
568
Opmerking: Voor optimale prestaties en efficiëntie van het product dient u bij het vullen rekening te
houden met de netto bruikbare capaciteit (laadlimiet).
Effect van temperatuurinstellingen op voedselverspilling:
Om voedselverspilling door ontbinding of uitdroging te beperken, moet dit apparaat binnen het
aangewezen werkingsbereikworden gebruikt.
Optimale temperatuur voor het bewaren van voedsel: 6°C
Neem contact op met uw Polar-dealer om reserveonderdelen te bestellen:
https://www.polar-refrigerator.com/stockist
Gewicht
(kg)
57
66
55
63,5
Minimumperiode voor de beschikbaarheid van reserveonderdelen:
Deurkrukken, deurscharnieren, knoppen, draaiknoppen en toetsen, deurpakkingen, toetsenborden,
manden en rekken voor opslag, naar gelang van het apparaat, zullen ter beschikking worden gesteld
aan zowel eindgebruikers als professionele gebruikers gedurende minimaal acht jaar nadat het laatste
apparaat van het model in de handel is gebracht. Een ruimere selectie van onderdelen zal voor deze
periode ook beschikbaar worden gemaakt voor professionele gebruikers.
Modelinformatie vindt u in de productdatabase:
Modelinformatie vindt u op het product:
De modelaanduiding staat meestal op de binnenwand en op de achterkant van het toestel.
Toelichting: Polar biedt een garantie van minimaal 2 jaar. Neem voor meer informatie contact op met de
bevoegde vertegenwoordiger.
12
Page 13
NL
Elektrische bedrading
Men dient de stekker op een geschikt stopcontact aan te sluiten.
De bedrading van dit apparaat is als volgt:
• Stroomkabel (bruin) naar de aansluitklem gemarkeerd met L
• Neutraalkabel (blauw) naar de aansluitklem gemarkeerd met N
• Aardekabel (groen/geel) naar de aansluitklem gemarkeerd met E
Dit apparaat moet worden geaard.
Bij twijfels raadpleeg een vakkundige elektricien.
De elektrische isolatiepunten mogen niet worden geblokkeerd. In geval van een nooduitschakeling
moeten de isolatiepunten direct toegankelijk zijn.
Afvalverwerking
De EU-richtlijnen vereisen dat koelproducten door gespecialiseerde bedrijven wordt verwerkt die gassen,
metalen en plastic componenten verwijderen of recyclen.
Raadpleeg uw plaatselijke afvalverwerkingsbedrijf voor informatie over de afvalverwerking van uw
apparaat. De plaatselijke overheden zijn niet verplicht om koelingsproducten van bedrijven als afval te
verwerken maar kunnen uw informeren waar u het apparaat kunt afgeven.
U kunt ook de Polar helplijn bellen voor informatie over landelijke afvalverwerkingsbedrijven in de EU.
Productconformiteit
Het WEEE-logo op dit product of bijbehorende documentatie geeft aan dat het product
niet onder huisvuil valt en als zodanig ook niet mag worden verwerkt. Ter preventie
van mogelijke gevaren voor de gezondheid van personen en/of voor het milieu,
dient men dit product in overeenstemming met het voorgeschreven en milieuveilige
recyclingproces als afval te verwerken. Raadpleeg uw productleverancier of uw plaatselijk
afvalverwerkingsbedrijf voor meer informatie over de juiste afvalverwerking van dit
product.
De onderdelen van Polar producten hebben strenge producttesten ondergaan om te
voldoen aan wettelijke regels en specificaties die door internationale, onafhankelijke en
landelijke overheden worden voorgeschreven.
Polar producten zijn goedgekeurd en voorzien van het volgende symbool:
Alle rechten voorbehouden. Het is verboden om deze handleiding, hetzij volledig of gedeeltelijk, elektronisch of mechanisch
te reproduceren, kopiëren, op opslagmedia op te slaan of op enigerlei wijze over te dragen, zonder voorafgaande
Wij hebben er alles aan gedaan om er zeker van te zijn dat op publicatiedatum van de handleiding alle details correct zijn,
desondanks, behoudt Polar het recht voor om specificaties zonder aankondiging te wijzigen.
goedkeuring van Polar.
13
Page 14
FR
Conseils de sécurité
Nous vous invitons à consacrer quelques instants à la lecture
attentive de ce mode d’emploi. L’entretien et l’utilisation
appropriés de cette machine vous permettront de tirer le meilleur
de votre produit POLAR.
• Placez l’appareil sur une surface plane, stable.
• L’installation et les éventuelles réparations doivent être
confiées à un dépanneur / technicien qualifié. Ne retirez aucun
composant ou cache de ce produit.
• Consultez les normes locales et nationales pour vous
conformer aux :
- lois sur l’hygiène et la sécurité au travail ;
- codes de bonnes pratiques BS EN ;
- précautions contre le risque d’incendie ;
- réglementations sur les branchements électriques IEE ;
- règlements sur la construction.
• NE PAS utiliser l’appareil en extérieur.
• NE PAS utiliser l’appareil pour entreposer des fournitures
médicales.
• NE PAS laisser de l’huile ou des graisses entrer en contact avec
les composants en plastique ou le joint de la porte. Nettoyer
immédiatement en cas de contact.
• NEPAS entreposer de produits sur le dessus de l’appareil.
• Les bouteilles contenant un fort pourcentage d’alcool doivent
être scellées et placées à la verticale dans le réfrigérateur.
• Toujours transporter, entreposer et manipuler l’appareil en
position verticale et le déplacer en le tenant par la base.
• Toujours éteindre et débrancher la source d’alimentation de
l’appareil avant de le nettoyer.
• Conserver tous les emballages hors de la portée des enfants.
Jeter les emballages conformément aux réglementations
émises par les autorités locales.
• Les enfants doivent être surveillés afin de s’assurer qu’ils ne
jouent pas avec l’appareil.
14
Page 15
FR
• NE PAS utiliser de laveurs à jet / pression pour nettoyer l’appareil.
• Cet appareil n’a pas été concu pour être utilisé par des
personnes (enfants inclus) à capacités physiques, sensorielles
ou mentales réduites ou ne disposant pas d/una expérience ou
de connaissances suffisantes, à moins que lesdites personnes
n’aient été formées ou instruites quant à son utilisation, par
une personne responsable de leur sécurité.
• POLAR recommande de faire tester régulièrement cet appareil
(une fois par an au minimum) par une personne compétente.
Le test devrait inclure, entre autres : inspection visuelle, test
de polarité, la continuité de masse, test d’isolation et test de
fonctionnement.
Attention : Risque d’ incendie
• Ne stockez pas de substances explosives telles que les
aérosols avec un propulseur inflammable dans cet appareil.
Attention : Ne bouchez pas les grilles d’aération. Le
meuble ne doit pas être encastré sans l’aération adéquate.
• Attention : Ne pas utiliser de dispositifs mécaniques ou
autresmoyens pour accélérer le processus de dégivrage,
autres que ceux recommandés par le fabricant.
• Attention : Ne pas endommager le circuit frigorifique.
• Attention : Ne pas utiliser d’appareils électriques à l’intérieur
des compartiments de stockage alimentaire de l’appareil.
Description du produit
GP292 Vitrine réfrigérée POLAR 120 l
GP291 Vitrine réfrigérée POLAR 160 l
PG003 Présentoir de comptoir verre carré POLAR 120 l
PG004 Présentoir de comptoir verre carré POLAR 160 l
Contenu
• Vitrine réfrigérée POLAR
• 2 étagères
POLAR attache une grande importance à la qualité et au service et veille à fournir des produits en parfait
état opérationnel, parfaitement intacts au moment de l’emballage.
Nous vous prions de contacter votre revendeur POLAR immédiatement si vous constatez un dommage
quelconque survenu pendant le transport du produit.
• Mode d’emploi
15
Page 16
FR
Installation
Remarque : Ne pas utiliser dans des
camionnettes ou des semi-remorques,
dans des camions-restaurants ou véhicules
similaires.
Remarque : dans les cas où l’appareil a été
stocké ou déplacé autrement qu’à la verticale,
placez-le en position debout pendant environ
12 heures avant de vous en servir. En cas de
doute, laissez l’appareil se reposer.
1. Sortez l’appareil de l’emballage. Veillez à bien
retirer toute la pellicule et les revêtements de
protection de toutes les surfaces.
2. Pour optimiser les performances et la longévité,
assurez-vous qu’un dégagement minimum
de 2,5 cm est maintenu entre l’unité et les
murs et autres objets, avec un dégagement
minimum de 20 cm sur le dessus. NE JAMAIS
PLACER À PROXIMITÉ D’UNE SOURCE DE
CHALEUR.
Remarque : Avant d’utiliser
l’appareil pour la première
fois, nettoyez les tablettes et
l’intérieurà l’eau savonneuse
puis séchez bien.
Fonctionnement
Panneau de commande
Le panneau de commande se trouve en dessous
des portes, à l’arrière de l’unité.
Mise sous tension
1. Fermez les portes de l’unité.
2. Branchez l’unité à l’alimentation secteur.
3. Appuyez sur le bouton pour allumer ou
éteindre l’éclairage, le cas échéant.
Réglage de la température de
fonctionnement
1. Appuyez sur le bouton SET. L’écran clignote.
2. Appuyez sur les boutons ou pour
afficher la température requise.
3. Appuyez sur le bouton SET pour enregistrer la
température.
Dégivrage manuel
Appuyez sur le bouton et maintenez-le enfoncé
pendant 6 secondes pour démarrer le dégivrage
automatique. Le voyant de dégivrage s’allume.
Le cycle de dégivrage se termine automatiquement.
Nettoyage, entretien et
maintenance
1. Veiller à éteindre et débrancher l’appareil
de l’alimentation avant de le nettoyer.
2. Les portes sont amovibles pour un nettoyage
plus aisé.
3. Nettoyer l’intérieur de l’unité aussi souvent que
possible.
4. Ne pas utiliser d’agents de nettoyage abrasifs,
car ils peuvent laisser des résidus dangereux.
5. Nettoyez le joint de la porte avec de l’eau
savonneuse chaude.
6. Veiller à toujours essuyer toutes les surfaces
après le nettoyage.
Conseils pour la réfrigération:
• L’ouverture fréquente et prolongée des portes
entraîne la formation de condensation et de
glace.
• Le fait de faire fonctionner l’appareil en dehors
de la plage de température recommandée et
de le placer à côté d’une source de chaleur
augmente également la quantité de glace et
de condensation interne/externe. En cas de
condensation externe, essuyez la surface avec
un chiffon.
• Une quantité excessive de glace entraînera
des temps de fonctionnement plus longs qui
augmenteront la consommation d’énergie et la
détérioration des composants.
• Si le joint ou la garniture est endommagé
ou déformé, la consommation d’énergie
augmentera. Pour rétablir l’efficacité, remplacez
le joint d’étanchéité.
Remplacement de l’ampoule intérieure
Appelez votre revendeur POLAR ou un électricien
qualifié. L’ampoule est disponible à la vente comme
pièce détachée.
16
Page 17
FR
Nettoyage du condensateur
Un nettoyage régulier du condensateur peut permettre de prolonger la vie de l’appareil. POLAR
recommande que le nettoyage du condensateur soit effectué par un agent POLAR ou un technicien
qualifié.
Si vous ne nettoyez pas le condenseur, la consommation d’énergie augmentera, les performances et la
durée de vie de votre unité Polar seront réduites et votre garantie pourrait être annulée.
Dépannage
Un technicien qualifié doit effectuer les réparations si nécessaire.
DysfonctionnementCause probableIntervention
L’appareil ne fonctionne
pas
L’appareil se met
sous tension, mais la
température est trop
élevée/basse.
L’appareil a une fuite
d’eau
L’appareil fait un
bruit plus fort que la
normale
L’ampoule d’éclairage
ne s’allume pas
La porte ne ferme pasSaleté / obstacle dans les glissières. Nettoyez les glissières.
Code d’erreur EE4
L’appareil n’est pas alluméVérifier que l’appareil est bien branché
La fiche ou le câble est endommagé Remplacez la fiche ou le câble
Défaut d’alimentation secteurVérifier l’alimentation secteur
Il y a trop de glace dans le
condensateur.
Le condensateur est obstrué par la
poussière.
Les portes ne ferment pas
correctement.
L’appareil se trouve à proximité
d’une source de chaleur, à la lumière
directe du soleil ou le flux d’air du
condensateur est obstrué.
La température ambiante est trop
élevée.
Des aliments inappropriés sont
entreposés dans l’appareil.
L’appareil est en surcharge.Réduisez la quantité d’aliments
L’appareil n’est pas à niveauAjustez les pieds à vis pour le mettre de
Vis / écrou desserrésVérifiez et resserrez toutes les vis et les
L’appareil n’a pas été installé dans
une position de niveau ou stable.
L’ampoule doit être remplacéeRemplacer la lampe
L’éclairage n’est pas allumé.Vérifiez que vous avez bien appuyé sur
• Flux d’air restreint
• Condenseur bloqué
et allumé
Dégivrez l’appareil
Nettoyer le condenseur
Vérifiez que les portes sont fermées et
que les joints ne sont pas endommagés.
Déplacez le réfrigérateur dans un endroit
plus approprié.
Augmentez la ventilation ou déplacez
l’appareil dans un endroit plus frais
Retirez tout aliment trop chaud ou toute
obstruction du ventilateur
entreposés dans l’appareil
niveau (le cas échéant).
écrous.
Vérifiez la position d’installation et
modifiez-la si nécessaire.
le bouton de l’éclairage.
• Augmenter le débit d’air
• Nettoyer le condenseur
17
Page 18
FR
Caractéristiques techniques
Remarque : raison de notre processus d’amélioration continue, les spécifications des produits sont
susceptibles d’être modifiées sans préavis.
Puiss-
Modèle Tension
GP292220-
GP2912001,42°C ~ 12°C108160R600a
PG0031601,42°C ~ 12°C83120R600a
PG0042001,42°C ~ 12°C106160R600a
240V~
50Hz
Courant
ance
(W)
1601,42°C ~ 12°C83120R600a
(A)
Plage de
tempéra-
ture
Capacité
Nette
(litres)
Volume
brut
(litres)
Type de
réfrigérant
/ poids (kg)
(0,050kg)
(0,065kg)
(0,050kg)
(0,065kg)
Dimensions
h x l x p
mm
686 x 696 x
568
686 x 874 x
568
686 x 702 x
568
686 x 880 x
568
Remarque : pour une performance et une efficacité optimales du produit, veillez à respecter la capacité
nette utilisable (limite de charge) lors du remplissage.
Impact des réglages de la température sur les déchets alimentaires :
Afin de réduire la décomposition ou la déshydratation des déchets alimentaires, cet apparaeil doit être
utilisé dans la plage de fonctionnement prévue.
La température maximale pour conserver la nourriture est de 6°C
Pour commander les pièces de rechange, veuillez contacter le Stockist
Polar:
https://www.polar-refrigerator.com/stockist
Poids
(kg)
57
66
55
63,5
Duréeminimale pour la réception des pièces de rechange:
Les poignées de porte, les charnières de porte, les boutons, les cadrans et les boutons, les joints de
porte, les plateaux périphériques, les paniers et les étagères de rangement, en fonction de l’appareil,
seront mis à la disposition des utilisateurs finaux et des utilisateurs professionnels pendant un minimum
de huit ans après la mise sur le marché de la dernière unité du modèle. Une sélection plus large de
pièces sera également mise à la disposition des utilisateurs professionnels pendant cette période.
L’information sur le modèle est disponible dans la base de données du
produit:
L’information sur le modèle est disponible sur le produit.
L’identifiant du modèle se trouve généralement sur la paroi intérieure et au dos de l’appareil.
Remarque : Polar offre une garantie minimale de 2 ans, veuillez contacter le représentant agréé pour plus
de détails.
18
Page 19
FR
Raccordement électrique
La prise doit être reliée à la prise secteur qui convient.
Cet appareil est câblé comme suit :
• Fil conducteur (brun) à la borne marquée L
• Fil neutre (bleu) à la borne marquée N
• Fil de terre (vert / jaune) à la borne marquée E
Cet appareil doit être mis à la terre.
En cas de doute, consultez un électricien qualifié.
Les points d’isolation électrique doivent être libres de toute obstruction. En cas de débranchement requis
en urgence, ils doivent être facilement accessibles.
Mise au rebut
Les règlements de l’UE exigent que les produits munis de réfrigérants soient mis au rebut par des
entreprises spécialisées, équipées pour extraire et recycler les composants à gaz, métalliques et en
plastique.
Adressez-vous à votre autorité chargée de la collecte des déchets pour ce qui concerne la mise au
rebut de votre appareil. Même si rien n’oblige les autorités locales à se charger de la mise au rebut du
matériel de réfrigération commerciale, elles pourraient être en mesure de vous conseiller sur les moyens
disponibles localement pour s’en débarrasser.
Vous pouvez aussi appeler le standard d’assistance Polar, qui saura vous renseigner sur les entreprises de
prise en charge nationalesau sein de l’UE.
Conformité
Le logoWEEE qui figure sur ce produit ou sa documentation indique qu'il ne doit pas
être mis au rebut avec les ordures ménagères. Pour éviter qu'il ne présente un risque
pour la santé humaine et / ou écologique, confiez la mise au rebut de ce produit à un
site de recyclage agréé respectueux de l'environnement. Pour de plus amples détails sur
la mise au rebut appropriée de ce produit, contactez le fournisseur du produit ou l'autorité
responsable de l'enlèvement des ordures dans votre région.
Les pièces Polar ont été soumises à des tests rigoureux pour pouvoir être déclarées
conformes aux normes et spécifications réglementaires définies par les autorités
internationales, indépendantes et fédérales.
Les produits Polar ont été déclarés aptes à porter le symbole suivant :
Tous droits réservés. La production ou transmission, partielles ou intégrales, sous quelque forme que ce soit ou par n’importe
quel moyen, tant électronique que mécanique, sous forme de photocopie, d’enregistrement ou autre de ce mode d’emploi
Nous nous efforçons, par tous les moyens dont nous disposons, de faire en sorte que les détails contenus dans le présent
mode d’emploi soient corrects en date d’impression. Toutefois, POLAR se réserve le droit de changer les spécifications de
sont interdites sans l’autorisation préalablement accordée par POLAR.
ses produits sans préavis.
19
Page 20
DE
Sicherheitshinweise
Bitte nehmen Sie sich einige Minuten Zeit und lesen Sie dieses
Handbuch sorgfältig durch. Nur bei korrekter Wartung und
vorschriftsgemäßem Betrieb kann Ihr POLAR-Produkt optimale
Leistung erzielen.
• Auf eine flache, stabile Fläche stellen.
• Alle erforderlichen Montage- und Reparaturarbeiten sollten
von Wartungspersonal oder einem qualifizierten Techniker
durchgeführt werden. Keine Bauteile oder Bedienflächen von
diesem Produkt entfernen.
• Für folgende Normen und Vorschriften sind die lokalen und
nationalen Normen heranzuziehen:
- Arbeitsschutzvorschriften
- BS-EN-Verhaltenspraktiken
- Brandschutzvorschriften
- IEE-Anschlussvorschriften
- Bauvorschriften
• Das Gerät NICHT mit einem Strahl-/Hochdruckreiniger reinigen
• Das Gerät NICHT im Freien einsetzen.
• Das Gerät NICHT zum Aufbewahren von medizinischen
Produkten verwenden.
• KEIN Öl oder Fett mit den Kunststoffteilen oder der Türdichtung
in Kontakt kommen lassen. Bei Kontakt sofort reinigen.
• KEINE Produkte auf dem Gerät lagern.
• Flaschen mit Alkohol in hoher Konzentration müssen dicht
verschlossen und aufrecht stehend im Kühlschrank aufbewahrt
werden.
• Das Gerät stets aufrecht tragen, lagern und transportieren.
Zum Transport das Gerät an der Unterseite anfassen.
• Vor Reinigungsarbeiten stets zunächst das Gerät abschalten
und den Netzstecker aus der Steckdose ziehen.
• Verpackungsmaterial außerhalb der Reichweite von Kindern
aufbewahren. Verpackungsmaterial gemäß den lokalen
Vorschriften entsorgen.
• Kinder sollten beaufsichtigt werden um sicherzustellen, dass
sie nicht mit dem Gerät spielen.
.
20
Page 21
DE
• Dieses Gerät solte nur dann von Personen (einschlißlich
Kindern) mit reduzierten körperlichen, sensorischen oder
geistigen Fähigkeiten, mangelnder Erfahrung oder Kenntnissen
verwendet werden, wenn sie von einer für ihre Sicherheit
verantwortlichen Person im Gebrauch des Geräts geschult
wurden bzw. ständig beautsichtigt werden.
• POLAR empfiehlt, dass dieses Gerät regelmäßig (wenigstens
jährlich) von einem Fachmann überprüft wird. Die
Überprüfung sollte beinhalten, ohne darauf beschränkt zu
sein: Visuelle Überprüfung, Polaritätstest, Erdungskontinuität,
Isolationskontinuität und Funktionalitätsprüfung.
Vorsicht: Brandgefahr
• Keine explosiven Stoffe wie Sprühdosen mit brennbarem
Treibmittel in diesem Gerät nicht speichern aufbewahren.
Warnung: Halten Sie alle Lüftungsöffnungen frei.
Das Gerät sollte nicht ohne geeignete Ventilation
eingebaut werden.
• Warnung: Verwenden Sie keine mechanischen Vorrichtungen
oder andere Mittel, um den Abtauvorgang zu beschleunigen,
außer denen, die vom Hersteller empfohlen wurden.
• Warnung: Beschädigen Sie den Kältemittelkreislauf nicht.
• Warnung: Verwenden Sie keine elektrischen Geräte innerhalb
der Ablagefächer des Geräts.
POLAR ist stolz auf die hochwertige Qualität seiner Produkte und seinen erstklassigen Service. Wir stellen
sicher, dass alle gelieferten Produkte zum Zeitpunkt der Verpackung voll funktionsfähig sind und sich in
einwandfreiem Zustand befinden.
Sollten Sie Transportschäden feststellen, wenden Sie sich bitte unverzüglich an Ihren POLAR-Händler.
• Bedienungsanleitung
21
Page 22
DE
Montage
Hinweis: Nicht zur Verwendung in
Lieferwagen oder Anhängern, Transportern
oder ähnlichen Fahrzeugen.
Hinweis: Wenn das Gerät nicht aufrecht
transportiert oder gelagert wurde, muss
es vor Inbetriebnahme rund 12 Stunden
aufrecht aufgestellt werden. Im Zweifelsfall
lassen Sie es aufrecht stehen.
1. Das Gerät aus der Verpackung nehmen. Darauf
achten, dass die gesamte Plastikfolie und
alle Beschichtungen von sämtlichen Flächen
entfernt wurden.
2. Um die Leistung und Langlebigkeit zu
optimieren, stellen Sie sicher, dass zwischen
dem Gerät und den Wänden und anderen
Objekten ein Mindestabstand von 2,5
cm eingehalten wird, wobei oben ein
Mindestabstand von 20 cm eingehalten
wird. NIEMALS IN DER NÄHE EINER
WÄRMEQUELLE.
Hinweis: Reinigen Sie die
Einlegeböden und das
Innere des Geräts vor der
ersten Inbetriebnahme mit
Seifenwasser und trocknen Sie
es gut ab.
Betrieb
Bedienfeld
Das Bedienfeld befindet sich unter den Türen auf
der Rückseite des Geräts.
Einschalten
1. Die Türen des Geräts schließen.
2. Das Gerät an den Netzstrom anschließen.
3. Die -Taste drücken, um das Licht nach Bedarf
ein- oder auszuschalten.
Betriebstemperatur einstellen
1. Die SET-Taste drücken. Die Anzeige blinkt auf.
2. Drücken Sie die Taste oder , um die
benötigte Temperatur aufzurufen.
3. Zum Speichern der Temperatur drücken Sie die
Taste SET.
Manuelles Abtauen:
Um den automatischen Abtauvorgang zu starten,
die Taste
Abtaulampe leuchtet auf.
Der Abtauzyklus wird automatisch beendet.
6 Sekunden lang gedrückt halten. Die
Reinigung, Pflege und
Wartung
1. Vor Reinigungsarbeiten zunächst das
Gerät abschalten und den Netzstecker
ziehen.
2. Zur problemlosen Lagerung lassen sich die
Türen ausbauen.
3. Das Gerät möglichst häufig innen reinigen.
4. Keine Scheuermittel verwenden, da diese
schädliche Rückstände hinterlassen können.
5. Die Türdichtung mit warmem Seifenwasser
reinigen.
6. Nach dem Reinigen stets mit einem Tuch
trocknen.
Tipps zum Kühlen:
• Bei häufigem und längerem Öffnen der Türen
bilden sich Kondenswasser und Eis.
• Wenn Sie das Gerät außerhalb des
empfohlenen Temperaturbereichs betreiben
und es in der Nähe einer Wärmequelle
aufstellen, erhöht sich ebenfalls die Menge
an Eis und interner/externer Kondensation.
Bei äußerer Kondensation wischen Sie die
Oberfläche mit einem Tuch ab.
• Übermäßige Vereisung führt zu längeren
Laufzeiten, die den Energieverbrauch erhöhen
und den Verschleiß der Komponenten
beschleunigen.
• Wenn die Dichtung beschädigt oder verformt
ist, erhöht sich der Energieverbrauch. Um
die Effizienz wiederherzustellen, die Dichtung
ersetzen.
Lampe innen auswechseln
Bitte wenden Sie sich an Ihren POLAR-Händler oder
einen qualifizierten Elektriker. Die Lampenbaugruppe
ist als separates Ersatzteil erhältlich.
22
Page 23
DE
Reinigen des Kondensator
Regelmäßiges Reinigen des Kondensator kann die Lebensdauer des Geräts verlängern. POLAR empfiehlt,
diese Reinigung von einem qualifizierten Techniker vornehmen zu lassen.
Wird der Kondensator nicht gereinigt, führt dies zu einer Erhöhung des Energieverbrauchs, einer Reduzierung
der Leistung und Lebensdauer Ihres Polar-Gerätes und möglicherweise zum Erlöschen Ihrer Garantie.
Störungssuche
Falls erforderlich, muss ein qualifizierter Techniker Reparaturen durchführen.
StörungVermutliche UrsacheLösung
Das Gerät
funktioniert nicht
Das Gerät lässt sich
einschalten, aber
die Temperatur ist
zu hoch/niedrig
Aus dem Gerät läuft
Wasseraus
Das Gerät ist
ungewöhnlich laut
Die Display-Lampe
leuchtet nicht
Tür schließt nichtSchmutz/Behinderung in den
Fehlercode EE4
Das Gerät ist nicht eingeschaltetPrüfen, ob der Netzstecker in die
Stecker und Kabel sind beschädigtStecker oder Leitung ersetzen
Fehler NetzstromversorgungNetzstromversorgung prüfen
Zu viel Eis auf dem KondensatorDas Gerät abtauen
Kondensator verstaubtKondensator reinigen
Türen sind nicht richtig geschlossenPrüfen, ob die Türen geschlossen und die
Gerät befindet sich in der Nähe
einerWärmequelle, in direkter
Sonneneinstrahlung oder der
Luftstrom zum Kondensator ist
unterbrochen
Umgebungstemperatur ist zu hochBelüftung intensivieren oder Gerät an
Ungeeignete Nahrungsmittel werden
im Gerät gelagert
Gerät ist überlastetWeniger Nahrungsmittel im Gerät lagern
Das Gerät steht nicht geradeDie Schraubfüße so regulieren, dass das
Muttern und/oder Schrauben sind
lose
Das Gerät steht nicht eben oder stabil Position überprüfen und bei Bedarf ändern
Die Lampe muss ausgewechselt
werden
Licht nicht eingeschaltetDarauf achten, dass der Lichtschalter
Führungsschienen
• Eingeschränkter Luftstrom
• Blockierter Kondensator
Steckdose gesteckt wurde und das Gerät
eingeschaltet ist
Dichtungen intakt sind
Das Gerät an einem geeigneteren Ort
aufstellen
einem kühleren Ort aufstellen
Zu heiße Nahrungsmittel oder Produkte,
die den Lüfter blockieren, herausnehmen
Gerät eben steht (sofern zutreffend)
Alle Muttern und Schrauben überprüfen
und anziehen
Ersetzen Sie die Lampe
korrekt gedrückt wird
Führungsschienen reinigen
• Luftstrom erhöhen
• Kondensator reinigen
23
Page 24
DE
Technische Spezifikationen
Hinweis: Aufgrund unseres kontinuierlichen Verbesserungsprozesses können sich die Produktspezifikationen
ohne Ankündigung.
Modell
GP292220-
GP2912001,42°C ~ 12°C108160R600a
PG0031601,42°C ~ 12°C83120R600a
PG0042001,42°C ~ 12°C106160R600a
Spann-
240V~
ung
50Hz
Leistung
Strom-
stärke
(W)
1601,42°C ~ 12°C83120R600a
(A)
Temperatur-
bereich
Nutzinhalt
(Liter)
Gesam-
tvo
lumen
(Liter)
Kältemittelart
/ Gewicht
(kg)
(0,050kg)
(0,065kg)
(0,050kg)
(0,065kg)
Abmess-
ungen
h x b x t
mm
686 x 696
x 568
686 x 874
x 568
686 x 702
x 568
686 x 880
x 568
Hinweis: Um eine optimale Leistung und Effizienz des Geräts zu gewährleisten, achten Sie bitte beim
Befüllen auf die Nettonutzkapazität (Belastungsgrenze).
Einfluss der Temperatureinstellungen auf die Lebensmittelverschwendung:
Um die Verschwendung von Lebensmitteln durch Zersetzung oder Austrocknung zu reduzieren, sollte
dieses Gerät in seinem vorgesehenen Betriebsbereich betrieben werden.
Optimale Temperatur für die Lagerung von Lebensmitteln: 6°C
Für Ersatzteilbestellungen bitte Ihren Polar Fachhändler kontaktieren:
https://www.polar-refrigerator.com/stockist
Gewicht
(kg)
57
66
55
63,5
Mindestzeitraum der Verfügbarkeit von Ersatzteilen:
Türgriffe, Türscharniere, Knöpfe, Drehregler und Knöpfe, Türdichtungen, periphere Ablagen, Körbe
und Lagerregale, soweit sie für das Gerät geeignet sind, sind sowohl für Endverbraucher als auch für
gewerbliche Nutzer mindestens acht Jahre lang nach Inverkehrbringen des letzten Geräts des Modells
verfügbar. Eine breitere Ersatzteil-Auswahl steht während dieses Zeitraums auch den gewerblichen
Anwendern zur Verfügung.
Modell-Informationen finden Sie in der Produktdatenbank:
Informationen zum Modell finden Sie auf dem Produkt:
Die Modellbezeichnung befindet sich in der Regel an der Innenwand und auf der Rückseite des Geräts.
Hinweis: Polar bietet eine Mindestgarantie von 2 Jahren. Bitte kontaktieren Sie Ihren autorisierten
Fachhändler für weitere Informationen.
24
Page 25
DE
Elektroanschlüsse
Der Stecker muss in eine geeignete Steckdose gesteckt werden.
Das Gerät ist wie folgt verdrahtet:
• Stromführender Leiter (braun) an Klemme L
• Neutralleiter (blau) an Klemme N
• Erdleiter (grün/gelb) an Klemme E
Dieses Gerät muss geerdet sein.
Bei Fragen wenden Sie sich bitte an einen qualifizierten Elektriker.
Elektroisolierpunkte dürfen nicht blockiert werden. Bei einem Notstopp müssen diese Punkte jederzeit
sofort zugänglich sein.
Entsorgung
Gemäß EU-Vorschriften müssen Kühlprodukte von Fachunternehmen entsorgt werden, die alle Gase,
Metall- und Kunststoffbauteile entfernen oder recyceln.
Ihre Kommunalverwaltung kann Sie über die Entsorgung Ihres Geräts informieren. Kommunalbehörden
sind nicht verpflichtet, gewerbliche Kühlgeräte zu entsorgen. Sie können Sie jedoch über lokale
Annahmestellen informieren, die diese Geräte entsorgen.
Oder rufen Sie die POLAR-Helpline an. Wir
verfügen über eine Liste nationaler Entsorger in den EU-Staaten.
Konformität
Das WEEE-Logo an diesem Produkt oder in der Dokumentation weist darauf hin, dass
das Produkt nicht mit dem normalen Hausmüll entsorgt werden darf. Um potenziellen
Gesundheits- bzw. Umweltschäden vorzubeugen, muss das Produkt durch einen
zugelassenen und umweltverträglichen Recyclingprozess entsorgt werden. Ausführliche
Informationen zur korrekten Entsorgung dieses Produkts erhalten Sie von Ihrem
Produktlieferanten oder der für die Müllentsorgung in Ihrer Region zuständige Behörde.
Alle POLAR-Produkte werden strengen Tests unterzogen, um die Einhaltung von
Normen und Spezifikationen internationaler und nationaler Behörden und unabhängiger
Organisationen zu gewährleisten.
POLAR-Produkte dürfen durch folgendes Symbol gekennzeichnet werden:
Alle Rechte vorbehalten. Diese Anleitung darf ohne vorherige schriftliche Genehmigung von POLAR weder ganz noch
teilweise in irgendeiner Form oder auf irgendeinem Wege - einschließlich elektronischer, mechanischer Verfahren, durch
Es werden alle Anstrengungen unternommen um sicherzustellen, dass alle Angaben bei der Drucklegung korrekt sind.
Fotokopieren, Aufnahme oder andere Verfahren - vervielfältigt oder übertragen werden.
POLAR behält sich jedoch das Recht vor, Spezifikationen ohne Vorankündigung zu ändern.
25
Page 26
IT
Suggerimenti per la sicurezza
Leggere con attenzione il presente manuale. La manutenzione e
l’utilizzo corretti di questo apparecchio consentiranno di ottenere
le massime prestazioni da questo prodotto POLAR.
• Posizionare su una superficie piana e stabile.
• L’installazione e le eventuali riparazioni devono venire eseguite
da un agente/tecnico qualificato. Non rimuovere i componenti
o i pannelli di accesso dell’apparecchio.
• Verificare la conformità alle normative locali e nazionali di
quanto segue:
- Normativa antinfortunistica sul lavoro
- Linee guida BS EN
- Precauzioni antincendio
- Normativa IEE sui circuiti elettrici
- Norme di installazione
• NON utilizzare sistemi di lavaggio a getto o a pressione per
pulire l’apparecchio.
• NON utilizzare l’apparecchio all’aperto.
• NON utilizzare l’apparecchio per conservare presidi medicosanitari.
• NON mettere a contatto olio o grassi con i componenti in
plastica o con la guarnizione dello sportello.
• Pulire immediatamente in caso di contatto.
• Non conservare prodotti collocandoli sopra l’apparecchio.
• Le bottiglie contenenti una elevata percentuale di alcool devono
venire sigillate e posizionate verticalmente nel frigorifero.
• Trasportare, immagazzinare e movimentare l’apparecchio sempre
in posizione verticale e spostarlo mantenendone la base.
• Spegnere e disconnettere l’alimentazione dell’unità prima di
pulirla.
• Tenere lontano l’imballaggio dalla portata dei bambini. Smaltire
l’imballaggio in conformità alle normative locali.
• Sorvegliare i bambini per assicurarsi che non giochino con
l’apparecchio.
26
Page 27
IT
• L’apparecchio non è destinato a essere utilizzato da persone
(inclusi i bambini) con ridotte capacita fisiche, sensoriali o
mentali, o prive della necessaria esperienza e conoscenza
dell’apparecchio, che non abbiano ricevuto supervisione o
istruzioni relative all’utilizzo dell’apparecchio dalle persone
responsabili dello loro sicurezza.
• POLAR raccomanda che questo apparecchio venga
periodicamente testato (almeno una volta all’anno) da una
persona competente. I test dovrebbero includere, ma non solo:
ispezione visiva, test di polarità, continuità di terra, continuità di
isolamento e test funzionale.
Attenzione: Rischio di incendio
• Non conservare sostanze esplosive, come bombolette
spray con propellente infiammabile in questo apparecchio.
Attenzione: Tenere libere tutte le aperture di
ventilazione. L’unità non deve essere installata
senzauna ventilazione adeguata.
• Attenzione: non utilizzare dispositivi meccanici o altri
mezzi per accelerare il processo di sbrinamento, diversa dal
fabbricante raccomandato Quelli da.
• Attenzione: Non danneggiare il circuito refrigerante.
• Attenzione: Non usare apparecchi elettrici all’interno degli
scomparti per la conservazione degli alimenti.
Descrizione del prodotto
Espositore refrigerato GP292 POLAR 120 litri
Espositore refrigerato GP291 POLAR 160 litri
Espositore da banco in vetro quadrato PG003 POLAR 120 litri
Espositore da banco in vetro quadrato PG004 POLAR 160 litri
Contenuto della confezione
• Espositore refrigerato POLAR
• Ripiani x 2
POLAR garantisce una qualità e un servizio impeccabili e assicura che al momento dell’imballaggio tutti i
componenti forniti sono integralmente funzionanti e privi di difetti. Nel caso siano rilevati danni risultanti
dal trasporto del prodotto, rivolgersi immediatamente al rivenditore POLAR locale.
• Manuale di istruzioni
27
Page 28
IT
Installazione
Nota: Non per l’uso in furgoni o rimorchi,
camion per il trasporto del cibo o veicoli
simili.
Nota: se l'apparecchio è stato immagazzinato
o spostato in posizione non verticale,
lasciarlo in posizione verticale per circa 12
ore prima di metterlo in funzione. In caso
di dubbio, osservare comunque questa
precauzione.
1. Rimuovere l’apparecchio dall’imballaggio.
Assicurarsi che la pellicola protettiva e
rivestimenti in plastica siano interamente
rimossi da tutte le superfici.
2. Per ottimizzare le prestazioni e la longevità,
assicurarsi che sia mantenuta una distanza
minima di 2,5 cm tra l’unità e le pareti e altri
oggetti, con una distanza minima di 20 cm
nella parte superiore. NON POSIZIONARE
MAI VICINO A UNA FONTE DI CALORE
Nota: prima di utilizzare
l’apparecchioper la prima volta,
pulire i ripiani e l’interno con
acqua saponata e asciugare
bene.
Funzionamento
Pannello di controllo
Il pannello di controllo è posizionato sotto le ante,
sulla parte posteriore dell’apparecchio.
Impostazione della temperatura di
funzionamento
1. Premere il pulsante SET. Il display lampeggia.
2. Premere il pulsante o per visualizzare la
temperatura richiesta.
3. Premere il pulsante SET per memorizzare la
temperatura.
Sbrinamento manuale
Premere senza rilasciare il pulsante per 6
secondi per avviare lo sbrinamento automatico. La
spia di sbrinamento si accende.
Il ciclo di sbrinamento si conclude automaticamente.
Pulizia e manutenzione
1. Prima di eseguire la pulizia, spegnere e
scollegare l’alimentazione.
2. Le ante possono essere rimosse per facilitare la
pulizia.
3. Pulire l’interno dell’apparecchio quanto più
spesso possibile.
4. Non utilizzare detergenti abrasivi in quanto
possono lasciare residui nocivi.
5. Pulire la tenuta della porta con acqua tiepida
calda.
6. Asciugare sempre dopo la pulizia.
Consigli per la refrigerazione:
• Con l’apertura frequente e prolungata delle
porte si formano condensa e ghiaccio.
• Anche il funzionamento al di fuori dell’intervallo
di temperatura consigliato e la collocazione
vicino a una fonte di calore aumentano la
formazione di ghiaccio e di condensa interna/
esterna. In caso di condensa esterna, pulire la
superficie con un panno.
• L’eccesso di ghiaccio provoca tempi di
funzionamento più lunghi che aumentano il
consumo energetico e il deterioramento dei
componenti.
• Se la guarnizione o la tenuta sono danneggiate
o deformate, il consumo energetico aumenta.
Per ripristinare l’efficienza, sostituire la
guarnizione.
Accensione
1. Chiudere le ante dell’apparecchio.
2. Collegare l’apparecchio all’alimentazione di
rete.
3. Premere il pulsante per accendere o
spegnere le luci.
28
Sostituzione della lampadina interna
Il gruppo lampadina interna è disponibile come
parte di ricambio, rivolgersi al rivenditore POLAR o
a un elettricista qualificato.
Page 29
IT
Pulizia del condensatore
La pulizia periodica del condensatore consente di prolungare il ciclo di vita dell’apparecchio. La pulizia del
condensatore deve venire eseguita da un tecnico qualificato o da un agente POLAR.
Non pulire il condensatore comporta un aumento del consumo energetico, una riduzione delle prestazioni
e della vita utile dell’unità Polar e può quindi invalidare la garanzia.
Risoluzione dei problemi
Se necessario, un tecnico qualificato deve eseguire le riparazioni.
GuastoProbabile causaAzione
L’apparecchio non
funziona
L’apparecchi si
accende ma la
temperatura è
troppo alta o troppo
bassa
L’apparecchio perde
acqua
L’apparecchio
presenta una
rumorosità eccessiva
La lampadina della
vetrina non si
accende
L’anta non si chiude Sporco/ostruzione nelle guidePulire le guide
Codice errore EE4
L’apparecchio non è accesoControllare che l’apparecchio sia
La presa e il cavo sono danneggiatiSostituire la spina o il cavo
Guasto alimentazione di reteControllare l’alimentazione di rete
Quantità eccessiva di ghiaccio nel
condensatore
Il condensatore è ostruito dalla
polvere
Le ante non sono chiuse in maniera
appropriata
L’apparecchio è posizionato in
prossimità di una sorgente di calore,
sotto la luce diretta del sole oppure
il flusso di aria al condensatore è
interrotto
La temperatura ambientale è troppo
alta
Sono stati conservati
nell’apparecchio cibi non appropriati
L’apparecchio è sovraccaricoRidurre la quantità dei cibi presenti
L’apparecchio non è in posizione
piana
Dadi o viti allentatiControllare e serrare tutti i dadi e le viti
L’apparecchio non è stato installato
in una posizione in piano o stabile
Sostituire la lampadinaSostituire la lampada
La luce non si accendeAssicurarsi che il pulsante della luce sia
• Flusso d’aria limitato
• Condensatore bloccato
correttamente collegato e acceso
Sbrinare l’apparecchio
Pulisci il condensatore
Controllare che le ante siano chiuse e
che le guarnizioni di tenuta non siano
danneggiate
Spostare l’apparecchio in una posizione più
appropria
Aumentare la ventilazione oppure spostare
l’apparecchio in una posizione più fresca
Rimuovere i cibi eccessivamente caldi o le
ostruzioni della ventola
nell’apparecchio
Regolare i piedi al fine di mantenere in
piano l’apparecchio (se pertinente)
Controllare la posizione di installazione e
cambiarla se necessario
stato premuto in maniera appropriata
• Aumentare il flusso d’aria
• Pulisci il condensatore
29
Page 30
IT
Specifiche tecniche
Nota: a causa del nostro continuo processo di miglioramento, le specifiche del prodotto sono soggette a
modifiche senza preavviso.
Modello Tensione
GP292220-
240V~
GP2912001,42°C ~ 12°C108160R600a
PG0031601,42°C ~ 12°C83120R600a
PG0042001,42°C ~ 12°C106160R600a
Alimen-
50Hz
Corrente
tazio
(W)
1601,42°C ~ 12°C83120R600a
(A)
Intervallo di
temperatura
Capacità
netta
(litri)
Volume
lorda
(litri)
Tipo di
refrigerante
/ peso (kg)
(0,050kg)
(0,065kg)
(0,050kg)
(0,065kg)
Dimensioni
h x l x p
mm
686 x 696 x
568
686 x 874 x
568
686 x 702 x
568
686 x 880 x
568
Nota: per ottenere prestazioni ed efficienza ottimali del prodotto, durante il rifornimento tenere presente
la capacità utile netta (limite di carico).
Impatto delle impostazioni di temperatura sulla generazione di rifiuti alimentari:
Al fine di ridurre lo spreco di cibo dovuto alla decomposizione o alla disidratazione, questo apparecchio
deve essere utilizzato nell’intervallo di funzionamento designato.
Temperatura ottimale per la conservazione degli alimenti: 6°C
Per ordinare le parti di ricambio, contattare il proprio Rivenditore Polar:
https://www.polar-refrigerator.com/stockist
Peso
(kg)
57
66
55
63,5
Periodo minimo di disponibilità delle parti di ricambio:
Le maniglie delle porte, le cerniere delle porte, i pomelli, i quadranti e i pulsanti, le guarnizioni delle
porte, i vassoi periferici, i cestelli e i ripiani per la conservazione, a seconda dell’apparecchio, saranno
messi a disposizione sia dei privati che dei professionisti per un minimo di otto anni dopo che l’ultima
unità del modello di riferimento è stata immessa sul mercato. Per questo periodo sarà inoltre messa a
disposizione dei Professionisti una selezione più ampia di parti.
Le informazioni sul modello possono essere trovate nel database del
prodotto:
Le informazioni sul modello possono essere trovate sul prodotto:
L’identificativo del modello si trova solitamente sulla parete interna e sul retro dell’unità.
Nota: Polar offre una garanzia minima di 2 anni, contattare un rappresentante autorizzato per maggiori
dettagli.
30
Page 31
IT
Cablaggi elettrici
La spina deve venire collegata a una presa di rete appropriata.
L’apparecchio ha i seguenti cablaggi:
• Filo sotto tensione (colore marrone) a terminale L
• Filo del neutro (colore blu) a terminale N
• Filo di terra (colore verde/giallo) a terminale E
Questa apparecchiatura deve essere collegata a terra.
In caso di dubbi, consultare un elettricista qualificato.
I punti di isolamento elettrico devono essere liberi da ostruzioni. In caso di emergenza, i punti devono
essere facilmente raggiungibili qualora sia necessario scollegarli.
Smaltimento
Le normative UE prevedono che lo smaltimento dei prodotti di refrigerazione sia eseguito da aziende
specializzate nella rimozione o nel riciclaggio di tutti i gas e dei componenti in metallo e plastica.
Rivolgersi all’ente locale incaricato per informazioni sullo smaltimento di questo apparecchio. Gli enti locali
non hanno l’obbligo di procedere allo smaltimento di apparecchi di refrigerazione commerciali ma sono in
grado di fornire suggerimenti sulla modalità di smaltimento di tali apparecchi.
In alternativa, chiamare la helpline telefonica di POLAR per ricevere informazioni dettagliate sulle aziende
di smaltimento nella UE.
Conformità
Il logoWEEE riportato su questo prodotto o sulla relativa documentazione indica che il
prodotto non può essere smaltito come normale rifiuto domestico. Per evitare possibili
danni alla salute e/o all'ambiente, il prodotto deve venire smaltito utilizzando una
procedura di riciclaggio approvata e sicura per l'ambiente. Per ulteriori informazioni su
come smaltire in maniera corretta questo prodotto, contattare il fornitore del prodotto o
l'ente locale responsabile per lo smaltimento dei rifiuti.
I componenti POLAR sono stati sottoposti a un rigoroso collaudo ai fini della conformità
agli standard e alle specifiche normative previste dalle autorità internazionali,
indipendenti e federali.
I prodotti POLAR sono autorizzati a esporre il seguente simbolo:
Tutti i diritti riservati. È vietata la riproduzione o la trasmissione in alcuna forma, elettronica, meccanica, mediante
fotocopiatura o altro sistema di riproduzione, di qualsiasi parte delle presenti istruzioni senza la previa autorizzazione
Le informazioni contenute sono corrette e accurate al momento della stampa, tuttavia POLAR si riserva il diritto di
modificare le specifiche senza preavviso.
scritta di POLAR.
31
Page 32
ES
Consejos de Seguridad
Tómese unos minutos para leer este manual. El correcto
mantenimiento y manejo de esta máquina proporcionará el
mejor funcionamiento posible de su producto POLAR.
• Colóquelo sobre una superficie plana, estable.
• Un agente del servicio técnico cualificado debería llevar a cabo
la instalación y cualquier reparación que se precise. No retire
ningún componente ni panel de servicio de este producto.
• Consulte las Normas Locales y Nacionales correspondientes a
lo siguiente:
- Legislación de Seguridad e Higiene en el Trabajo
- Códigos de Práctica BS EN
- Precauciones contra Incendios
- Normativas de Cableado de la IEE
- Normativas de Construcción
• No utilice dispositivos de lavado de chorro a presión para
limpiar el aparato.
• NO utilice el aparato en exteriores.
• NO utilice este aparato para almacenar existencias médicas.
• NO permita que el aceite o la grasa entren en contacto con los
componentes de plástico o con el cierre de la puerta. En caso
de contacto, límpielos inmediatamente.
• NO ponga ningún producto sobre el aparato.
• Las botellas que contengan un alto porcentaje de alcohol
deben estar bien cerradas y colocarse en posición vertical en
la unidad refrigerada.
• Mueva, guarde y maneje siempre el aparato en posición
vertical y agarrándolo por la base.
• Apague y desenchufe siempre el aparato antes de limpiarlo.
• Mantenga todo el embalaje fuera del alcance de los niños.
Elimine el embalaje de acuerdo con las normativas de las
autoridades locales.
• Los niños deben estar bajo supervisión para evitar que no
jueguen con el aparato.
32
Page 33
ES
• Este aparato ne debe ser utilizado por personas (niños
incluidos) que tengan limitadas sus capacidades fisicas,
senoriales o mentales que no tengan experiencia y
conocimientos, a menos que estén bajo la supervision o hayan
recibido instrucciones relatives al uso del aparato a cargo de
una resona responsable de su seguridad.
• POLAR recomienda que este aparato debe ser periódicamente
probado (al menos anualmente) por una Persona Competente.
La prueba debe incluir, pero no debe estar limitado a:
Inspección visual, Prueba de polaridad, Toma a tierra,
continuidad de aislamiento y prueba Funcional.
Precaución: Riesgo de Incendio
• No guarde sustancias explosivas, tales como latas de aerosol
con un propulsor inflamable, en este aparato.
Advertencia: Mantenga los orificios de ventilación
libres deobstrucciones. Asegúrese de que la
unidad disponga de una ventilación adecuada.
• Advertencia: No utilice dispositivos mecánicos u otros
medios para acelerar el proceso de descongelación, que no
sean aquellos recomendados por el fabricante.
• Advertencia: No dañe el circuito refrigerante.
• Advertencia: No utilice aparatos eléctricos dentro de los
compartimentos de almacenamiento de alimentos del aparato.
POLAR se enorgullece de su calidad y servicio y asegura que en el momento del embalaje, el contenido
se suministró con plena funcionalidad y sin ningún defecto.
Si encontrara algún daño resultante del transporte, póngase en contacto inmediatamente con su
distribuidor POLAR.
• Manual de instrucciones
33
Page 34
ES
Instalación
Nota: No debe utilizarse en furgonetas
o remolques, camiones de alimentos o
vehículos similares.
Nota: Si el aparato no se ha almacenado o
transportado en posición vertical, déjelo en
posición vertical durante aproximadamente
12 horas antes del funcionamiento. Si tiene
alguna duda, deje el aparato en posición
vertical.
1. Desembale el aparato. Asegúrese de que todos
los revestimientos y las láminas de plástico
de protección se hayan quitado totalmente de
todas las superficies.
2. Para optimizar el rendimiento y la longevidad,
asegúrese de que se mantenga un espacio libre
mínimo de 2,5 cm entre la unidad y las paredes
y otros objetos, con un espacio mínimo de 20
cm en la parte superior. NUNCA UBICAR AL
LADO DE UNA FUENTE DE CALOR.
Nota: antes de utilizar el aparato
por primera vez, limpie los
estantes y el interior con agua
con jabón.
Funcionamiento
Panelde control
El panel de control se encuentra ubicado debajo de
las puertas traseras del aparato.
Encendido
1. Cierre las puertas del aparato.
2. Conecte el aparato a una toma de alimentación
de corriente.
3. Pulse el botón para encender o apagar la luz.
Ajuste de la temperatura de
funcionamiento
1. Pulse el botón SET. La pantalla empezará a
parpadear.
2. Pulse los botones o hasta que aparezca
la temperatura deseada.
3. Pulse el botón SET para guardar la
temperatura.
Descongelación manual
Pulse y mantenga pulsado el botón durante 6
segundos para que empiece la descongelación
automática. La luz de descongelación se iluminará.
El ciclo de descongelación finalizará automáticamente.
Limpieza, cuidados y
mantenimiento
1. Apague el aparato y desenchufe el cable de la
toma de corriente antes de limpiarlo.
2. Puede quitar las puertas para que la limpieza le
resulte más fácil.
3. Limpie el interior del aparato con la mayor
frecuencia posible.
4. No utilice productos de limpieza abrasivos.
Estos pueden dejar residuos nocivos.
5. Limpie el sello de la puerta con agua tibia y
jabonosa.
6. Seque bien el aparato después de limpiarlo.
Consejos de refrigeración:
• La condensación y el hielo se formarán con
la apertura frecuente y prolongada de las
puertas.
• El funcionamiento fuera del rango de
temperatura recomendado y la colocación junto
a una fuente de calor también aumentarán la
cantidad de hielo y la condensación interna/
externa. Si se produce condensación externa,
limpie la superficie con un paño.
• El exceso de hielo provocará tiempos de
funcionamiento más largos que aumentarán
el consumo de energía y el deterioro de los
componentes.
• Si la junta o el sello están dañados o
deformados, aumentará el consumo de energía.
Para restablecer la eficiencia, sustituya la junta.
Cambio de la bombilla interior
Llame a su distribuidor de POLAR o a un electricista
cualificado. El Conjunto de la bombilla se vende
como pieza de repuesto.
34
Page 35
ES
Limpieza del condensador
Una limpieza periódica del condensador puede prolongar la vida del aparato. POLAR le recomienda que
contacte con un agente de POLAR o con un técnico cualificado para limpiar el condensador.
No limpiar el condensador aumentará el consumo energético, reducirá el rendimiento y la vida útil de su
unidad Polar y, por lo tanto, invalidará la garantía.
Resolución de problemas
Un técnico calificado debe realizar las reparaciones si es necesario.
FalloCausa probableAcción
El aparato no
funciona
El aparato se
enciende pero la
temperatura es
demasiado alta/baja
Hay fugas de agua
en el aparato
El aparato hace más
ruido del normal
La bombilla de
la pantalla no se
ilumina
La puerta no cierraSuciedad/obstáculos en los
Código de error EE4
El aparato no está conectadoCompruebe que el aparato esté enchufado
El enchufe y el cable están dañados Reemplace el enchufe o el cable
Fallo de la fuente de alimentación de
red
Demasiado hielo en el condensadorDescongele el aparato
El condensador se ha bloqueado con
polvo
Las puertas no están bien cerradasCompruebe que las puertas estén cerradas
El aparato está colocado cerca de
una fuente de calor, bajo la luz
directa delsol o el flujo de aire hacia
el condensador está interrumpido
La temperatura ambiente es
demasiado alta
Los alimentos guardados en el
aparato no son los adecuados
El aparato está sobrecargadoReduzca la cantidad de alimentos
El aparato no está bien niveladoAjuste las patas de rosca para nivelar el
Tornillo/tuerca flojosCompruebe y apriete todas las tuercas y
El aparato no se ha instalado en una
posición estable o nivelada
Hay que cambiar la bombillaReemplazar la lámpara
No se ha encendido la luzAsegúrese de haber pulsado bien el botón
conductos
• Flujo de aire restringido
• Condensador bloqueado
correctamente y conectado
Compruebe la fuente de alimentación de
red
Limpiar el condensador
y las juntas no estén dañadas
Traslade el refrigerador a un lugar más
adecuado
Aumente la ventilación o traslade el
aparato a un lugar más fresco
Retire cualquier exceso de alimentos
calientes u objetos que estén bloqueando
el ventilador
guardados en el aparato
aparato (si están incluidas)
tornillos
Compruebe la posición de instalación y
cámbiela en caso necesario
de la luz
Limpie los conductos
• Aumentar el flujo de aire
• Limpiar el condensador
35
Page 36
ES
Especificaciones Técnicas
Nota: Debido a nuestro proceso de mejora continua, las especificaciones del producto están sujetas a
cambios sin previo aviso.
Modelo Tensión
GP292220-
240V~
GP2912001,42°C ~ 12°C108160R600a
PG0031601,42°C ~ 12°C83120R600a
PG0042001,42°C ~ 12°C106160R600a
Potencia
50Hz
Corriente
(W)
1601,42°C ~ 12°C83120R600a
(A)
Margen de
Tempera-
turas
Capacidad
Neta
(litros)
Volúmen
Bruto
(litros)
Tipo de
refrigerante
/ peso (kg)
(0,050kg)
(0,065kg)
(0,050kg)
(0,065kg)
Dimensiones
a x a x p mm
686 x 696 x
686 x 874 x
686 x 702 x
686 x 880 x
Nota: Para un rendimiento y una eficiencia óptimos del producto, asegúrese de tener en cuenta la
capacidad neta utilizable (límite de carga) al llenarlo.
Impacto de los ajustes de temperatura en el desperdicio de alimentos:
Para reducir el desperdicio de alimentos por descomposición o deshidratación, este aparato debe
funcionar en su rango de funcionamiento designado.
Temperatura óptima para el almacenamiento de alimentos: 6°C
Para pedir piezasde repuesto, contáctese con su distribuidor Polar:
https://www.polar-refrigerator.com/stockist
568
568
568
568
Peso
(kg)
57
66
55
63,5
Período mínimo de piezas de repuesto que deben estar disponibles:
Los tiradores, bisagras, pomos, diales y botones de las puertas, las juntas de las puertas, las bandejas
periféricas, las cestas y los estantes para el almacenamiento, según corresponda al aparato, se pondrán
a disposición tanto de los usuarios finales como de los usuarios profesionales durante un mínimo
de ocho años después de la comercialización de la última unidad del modelo. También se pondrá a
disposición de los usuarios profesionales una selección más amplia de piezas durante este periodo.
La información sobre el modelo se puede encontrar en la base de datos de
productos:
La información sobre el modelo se puede encontrar en el producto:
El identificador del modelo suele encontrarse en la pared interior y en el reverso de la unidad.
Nota: Polar ofrece una garantía mínima de 2 años, contáctese con el representante autorizado para
obtener más detalles.
36
Page 37
ES
Cableado Eléctrico
El enchufe tiene que conectarse a una toma eléctrica adecuada.
Este aparato está conectado de la forma siguiente:
• Cable cargado (de color marrón) al terminal marcado como L
• Cable neutro (de color azul) al terminal marcado como N
• Cable de tierra (de color verde / amarillo) al terminal marcado como E
Este aparato debe conectarse a una toma de tierra.
Si tiene alguna duda, consulte a un electricista cualificado.
Los puntos de aislamiento eléctrico deben mantenerse libres de cualquier obstrucción. En caso de
precisarse una desconexión de emergencia, deben estar disponibles de forma inmediata.
Desecho
Las normativas de la UE requieren que los productos de refrigeración sean desechados por compañías
especializadas que extraigan o reciclen todos los gases, componentes metálicos y de plástico.
Consulte a su autoridad local de recogida de residuos a la hora de desechar su aparato. Las autoridades
locales no están obligadas a eliminar los equipos de refrigeración comerciales pero pueden ofrecer
consejo sobre cómo desechar los equipos localmente.
Otra opción es llamar a la línea de asistencia de POLAR para pedir información sobre las compañías
nacionales de desechos de la UE.
Cumplimiento
El logotipo WEEE en este producto o su documentación indica que no debe eliminarse
como un residuo doméstico. Para ayudar a prevenir posibles daños a la salud humana y/
o el medio ambiente, el producto debe eliminarse en un proceso de reciclaje aprobado y
medioambientalmente seguro. Para obtener más información sobre cómo eliminar
correctamente este producto, póngase en contacto con el proveedor del mismo o la
autoridad local responsable de la eliminación de residuos en su zona.
Las piezas POLAR han pasado estrictas pruebas de productos para cumplir las
especificaciones y normas reguladoras establecidas por las autoridades internacionales,
independientes y federales.
Los productos POLAR han sido autorizados para llevar el símbolo siguiente:
Reservados todos los derechos. Puede estar prohibida la reproducción o transmisión en cualquier forma o por cualquier
medio electrónico, mecánico, de fotocopiado, registro o de otro tipo, de cualquier parte de estas instrucciones sin la
Se ha hecho todo lo posible para garantizar que todos los datos son correctos en el momento de su publicación; sin
embargo,POLAR se reserva el derecho a modificar las especificaciones sin que medie notificación previa.