Polar DA680, FA854, FA856, FA855, FA857 User Manual [en, fr, it, es, nl +1]

Page 1
G-Series Countertop Prep Fridge
Instruction manual
EN
G-Series Countertop Prep Fridge
Handleiding
NL
G-serie voorzetkoelkast
Handleiding
FR
Série G Réfrigérateur de comptoir
Mode d'emploi
2
8
14
DE
Bedienungsanleitung
IT
Frigorifero da banco serie G
Manuale di istruzioni
ES
Frigorífico de sobremesa Serie G
Manual de instrucciones
Model • Modèle • Modell • Modello • Modelo • Malli:
FA854/FA855/FA856/FA857/DA680
20
26
32
Page 2
EN
Safety Instructions
• Position on a flat, stable surface.
• A service agent/qualified technician should carry out installation and any repairs if required. Do not remove any components or service panels on this product.
• Consult Local and National Standards to comply with the following:
- Health and Safety at Work Legislation
- BS EN Codes of Practice
- Fire Precautions
- IEE Wiring Regulations
- Building Regulations
• DO NOT use jet/pressure washers to clean the appliance.
• DO NOT use the appliance outside.
• DO NOT use this appliance to store medical supplies.
• Always carry, store and handle the appliance in a vertical position and move by holding the base of the appliance.
• Always switch off and disconnect the power supply to the unit before cleaning.
• Keep all packaging away from children. Dispose of the packaging in accordance with the regulations of local authorities.
• If the power cord is damaged, it must be replaced by a POLAR agent or a recommended qualified technician in order to avoid a hazard.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
2
Page 3
EN
• Polar recommends that this appliance should be periodically tested (at least annually) by a Competent Person. Testing should include, but not be limited to: Visual Inspection, Polarity Test, Earth Continuity, Insulation Continuity and Functional Testing.
• Polar recommend that this product is connected to a circuit protected by an appropriate RCD (Residual Current Device).
Caution: Risk of Fire
• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
Warning: Keep all ventilation openings clear of obstruction. Unit should not be boxed in without adequate ventilation.
• Warning: Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
• Warning: Do not damage the refrigerant circuit.
• Warning: Do not use electrical appliances inside the food storage compartments of the appliance.
Introduction
Please take a few moments to carefully read through this manual. Correct maintenance and operation of this machine will provide the best possible performance from your POLAR product.
Pack Contents
The following is included:
• POLAR Refrigerator
• Instruction manual
POLAR prides itself on quality and service, ensuring that at the time of unpacking the contents are supplied fully functional and free of damage.
Should you find any damage as a result of transit, please contact your POLAR dealer immediately.
• Gastranorm spacer bar
• Adjustable feet x 4
3
Page 4
EN
Installation
Not for use in vans or trailers, food trucks or similar vehicles.
If the unit has not been stored or moved in an upright position, let it stand upright for approximately 12 hours before operation. If in doubt allow to stand.
1. Remove the appliance from the packaging. Make sure that all protective plastic film and coatings are thoroughly removed from all surfaces.
2. To optimize performance and longevity, ensure a minimum clearance of 2.5cm is maintained between the unit and walls and other objects, with a minimum 20cm clearance on the top.
NEVER LOCATE NEXT TO A HEAT SOURCE.
Note: Before using the appliance for the first time, clean the interior with soapy water then dry well.
• Level the appliance by adjusting the screw feet.
Operation
Turn On
1. Ensure the power switch is set to [O] and turn on at the socket.
2. Switch on the power switch [I]. The current temperature within the appliance is displayed.
Set the Operating Temperature
1. Press the SET button 3 seconds. The display will flash.
2. Press the required temperature.
3. Press the SET button to store the temperature.
or buttons to display the
Manual Defrost
Press and hold the defrost button “aux” for 2 seconds to begin a manual defrost. The defrost light illuminates.
The defrost cycle will end automatically.
Storing Food
To get the best results from your POLAR appliance, follow these instructions:
• Only store foodstuffs in the appliance when it has reached the correct operating temperature.
• Ensure gastronorm bays are full at all times, even if the gastronorms are unused or empty. Empty bays will greatly reduce efficiency of the appliance.
• Use the spacer bars provided to fill any gaps (they are not required to support each GN pans).
• Do not obstruct the fans inside the appliance.
Note: The appliance is not intended for the long term storage of food.
4
Page 5
EN
Cleaning, Care & Maintenance
• Switch off and disconnect from the power supply before cleaning.
• Clean the interior of the appliance as often as possible.
• Do not use abrasive cleaning agents. These can leave harmful residues.
• Clean the door seal with warm soapy water.
• Always wipe dry after cleaning.
• Do not allow water used in cleaning to run through the drain hole into the evaporation pan.
• Take care when cleaning the rear of the appliance. Sharp edges can cut.
Condensation and ice will form with frequent and prolonged opening of the lid. Operating outside of the recommend temperature range and placing next to a heat source will also increase the amount of ice and internal/external condensation. If external condensation occurs wipe the surface down with a cloth. Excessive ice will result in longer running times that will increase energy consumption and increase the deterioration of components.
Cleaning the Condenser Filter
• The condenser is part of the refrigeration system. The condenser filter requires monthly cleaning.
• Always disconnect power supply before carrying out Routine Maintenance.
• Failure to clean the condenser filter will reduce the performance and life of your Polar unit and may invalidate your warranty.
• These models have a removable filter which can be cleaned with a vacuum cleaner.
Troubleshooting
A qualified technician must carry out repairs if required.
Fault Probable Cause Solution
The appliance is not working
The unit is not switched on Check unit plugged in correctly and
switched on Plug or lead is damaged Replace Plug or lead Fuse in the plug has blown Replace the fuse Mains power supply fault Check mains power supply
5
Page 6
EN
The appliance turns on, but the temperature is too high/low
The appliance is leaking water
The appliance is unusually loud
Fault Probable Cause Solution
Too much ice on the evaporator Defrost the appliance Condenser blocked with dust Clean the Condenser Doors are not shut properly Check lid is shut and seals are not
damaged
Appliance is located near a heat source or air flow to the condenser
Move the appliance to a more suitable
location
is being interrupted Ambient temperature is too high Increase ventilation or move appliance to a
cooler position
Unsuitable foodstuffs are being stored in the appliance
Remove any excessive hot foodstuffs or
blockages to the fan
Appliance is overloaded Reduce the amount of food stored in the
appliance
The appliance is not properly levelled
Adjust the screw feet to level the appliance
(if applicable)
The discharge outlet is blocked Clear the discharge outlet Movement of water to the drain is
obstructed The water container is damaged
Clear the floor of the appliance (if
applicable)
Consult a qualified Technician
The drip tray is overflowing Empty the drip tray (if applicable) Loose nut/screw Check and tighten all nuts and screws The appliance has not been installed
in a level or stable position
Check installation position and change if
necessary
Technical Specifications
Note: Due to our continuing program of research and development, the specifications herein may be subject to change without notice.
Model Voltage Power Current
FA854 220-240V~
FA855 110W 0.8A 2°C - 8°C 7 x gastronorm 1/4
FA856 122W 0.8A 2°C - 8°C 8 x gastronorm 1/4
FA857 122W 0.8A 2°C - 8°C 10 x gastronorm 1/4
DA680 110W 0.8A 2°C - 8°C 6 x gastronorm 1/4
6
110W 0.8A 2°C - 8°C 5 x gastronorm 1/4
50Hz
Temperature
Range
Capacity Refrigerant
Container
Container
Container
Container
Container
R600a 274 x 1200 x 335 25
R600a 274 x 1500 x 335 29
R600a 274 x 1800 x 335 32
R600a 274 x 2000 x 335 34
R600a 274 x 1400 x 335 27
Dimensions
H x W x D mm
Weight
(kg)
Page 7
EN
Electrical Wiring
POLAR appliances are supplied with a 3 pin BS1363 plug and lead.
The plug is to be connected to a suitable mains socket.
POLAR appliances are wired as follows:
• Live wire (coloured brown) to terminal marked L
• Neutral wire (coloured blue) to terminal marked N
• Earth wire (coloured green/yellow) to terminal marked E
This appliance must be earthed.
If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required they must be readily accessible.
Disposal
EU regulations require refrigeration product to be disposed of by specialist companies who remove or recycle all gasses, metal and plastic components.
Consult your local waste collection authority regarding disposal of your appliance. Local authorities are not obliged to dispose of commercial refrigeration equipment but may be able to offer advice on how to dispose of the equipment locally.
Alternatively call the POLAR helpline for details of national disposal companies within the EU.
Compliance
The WEEE logo on this product or its documentation indicates that the product must not be disposed of as household waste. To help prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area.
POLAR parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and federal authorities.
POLAR products have been approved to carry the following symbol:
All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic,
Every effort is made to ensure all details are correct at the time of going to press, however, POLAR reserve the right to
mechanical, photocopying, recording or otherwise, without the prior written permission of POLAR.
change specifications without notice.
7
Page 8
NL
Veiligheidstips
• Plaatsen op een vlakke en stabiele ondergrond.
• De installatie en eventuele reparaties zijn door een servicetechnicus/vaktechnicus uit te voeren. Verwijder geen componenten of servicepanelen van dit product.
• Raadpleeg en volg de plaatselijke en nationale regelgeving op m.b.t. tot het volgende:
- Wetgeving van gezondheid en veiligheid op de werkplaats
- Werkregels
- Brandpreventie
- IEE bekabelingsnormen
- Bouwverordeningen
• Dit product NIET reinigen met spuit-/drukreinigers.
• Uitsluitend geschikt voor gebruik binnenshuis.
• Dit product NIET gebruiken voor de berging van medische producten.
• Dit product altijd in een verticale positie vervoeren, opbergen en gebruiken. Het product aan de kastbasis vervoeren.
• Alvorens dit product te reinigen dient men altijd de stroomvoorziening uit te schakelen.
• Laat verpakkingsmateriaal niet binnen handbereik van kinderen. Verpakkingsmateriaal in overeenstemming met de regelgeving van de plaatselijke overheden als afval laten verwerken.
• Indien de stroomkabel beschadigd raakt, dient men deze door een POLAR technicus of een aanbevolen vaktechnicus te laten vervangen om gevaarlijke situaties te verhinderen.
• Dit apparaat is niet bedoeld voor gebruik door personen met lichamelijke, zintuigijike of mentale beperkingen (inclusief kinderen) of met gebrek aan ervaring of kennis tenzij zij hierin worden begeleid of zijn opgeleid in het gebruik van het apparaat door een persoon, die verantwoodelijk is voor hun veiligheid.
8
Page 9
NL
• POLAR beveelt aan dat dit apparaat periodiek (minstens jaarlijks) door een bevoegde persoon wordt getest. Tests moeten omvatten, maar zijn niet beperkt tot: visuele inspectie, polariteit, aardings continuïteit, isolatie continuïteit en functionele test.
Voorzichtig: Risico bij open Vuur
• Heeft explosieve stoffen zoals spuitbussen niet slaan met een brandbaar drijfgas in dit apparaat.
Waarschuwing:
Hou alle ventilatieopeningen vrij van obstakels. De eenheid mag niet ingesloten worden zonder geschikte ventilatie.
• Waarschuwing: mechanische apparaten of andere middelen niet gebruiken om het ontdooien te versnellen, met uitzondering van de fabrikant aanbevolen die door.
• Waarschuwing: het koelcircuit niet beschadigen.
• Waarschuwing: Gebruik geen elektrische apparaten binnen het voedsel opbergvakken van het apparaat.
Inleiding
Neem de tijd en lees deze handleiding aandachtig door. Een correct gebruik en onderhoud van deze machine waarborgt de beste prestatie van uw POLAR product.
Verpakkingsinhoud
De verpakking bevat het volgende:
• POLAR Koelkast of vrieskast
• Handleiding
POLAR is trots op de haar productkwaliteit en dienstverlening en controleer de inhoud van de verpakkingen, tijdens de verpakkingsfase, op functionaliteit en schade.
• Gastronorm aanpasbare stang
• Verstelbare poten x 4
Mocht u product door transport zijn beschadigd, neem dan onmiddellijk contact op met uw POLAR dealer.
9
Page 10
NL
Installatie
Opmerking: Niet voor gebruik in bestelwagens of aanhangwagens, foodtrucks of soortgelijke voertuigen.
Opmerking: indien het apparaat niet in een rechtopstaande positie is opgeslagen of vervoerd, dient men het product 12 uur vóór gebruik in de rechtopstaande positie te plaatsen. Bij twijfel dient men het product in een rechtopstaande positie te plaatsen.
1. Haal het product uit de verpakking. Zorg ervoor dat u de beschermingsfolie en -lagen van alle oppervlakken heeft verwijderd.
2. Om de prestaties en levensduur te optimaliseren, dient u ervoor te zorgen dat er minimaal 2,5 cm afstand wordt gehouden tussen de unit en muren en andere objecten, met een minimale vrije ruimte van 20 cm aan de bovenkant. PLAATS NOOIT NAAST EEN
WARMTEBRON.
Opmerking: Voordat u het apparaat voor het eerst gebruikt, moet u de binnenkant schoonmaken met zeepwater en vervolgens goed afdrogen.
• Nivelleer het product door de verstelbare poten aan te passen.
Inschakelen
1. Controleer of stroomschakelaar in de positie [O] staat en de steker in het stopcontact zit.
2. Zet de Power (Stroom) [I] aan. De actuele interne temperatuur van het product wordt weergegeven.
Werktemperatuur instellen
1. Houd de SET toets gedurende 3 seconden ingedrukt. Het display knippert.
2. Druk op de vereiste temperatuur weer te geven.
3. Druk op de SET knop om de temperatuurwaarde op te slaan.
of knoppen om de
Handmatig ontdooien
De knop aux indrukken en gedurende 2 seconden ingedrukt houden om ontdooiing te starten. Het ontdooiingslampje gaat aan.
De ontdooicyclus eindigt automatisch.
Bediening
Opslag van levensmiddelen
Volg de volgende aanwijzingen voor de beste resultaten met uw POLAR product:
• Bewaar uitsluitend levensmiddelen in het product wanneer het product de juiste gebruikstemperatuur heeft gereikt.
• Zorg dat alle gastronorm bakken altijd vol zijn, zelfs wanneer de gastronorms niet gebruikt of leeg zijn. Lege bakken zullen de efficiëntie van het product aanzienlijk verminderen.
• Gebruik de afstandhouders geleverd om eventuele lacunes op te vullen (ze zijn niet verplicht om elke GN pan ondersteunen).
• Niet de interne ventilatoren in het product blokkeren.
Opmerking: het apparaat is niet bedoeld voor het langdurig bewaren van voedsel.
10
Page 11
NL
Reiniging, zorg & onderhoud
• Alvorens het apparaat te reinigen dient men de stroomvoorziening uit te schakelen.
• Reinig zo vaak mogelijk de binnenkant van het product.
• Gebruik géén schurende reinigingsmiddelen. Dergelijke middelen kunnen schadelijke resten achterlaten.
• Reinig de deurdichting met warm zeepwater.
• Na reiniging altijd droogmaken.
• Het voor reiniging gebruikte water mag niet door het afvoergat naar de verdampingspan stromen.
• Ga voorzichtig te werk bij het reinigen van de achterzijde van het product. Scherpe randen kunnen snijwonden veroorzaken.
Bij veelvuldig en langdurig openen van de deuren zal zich condens en ijs vormen. Gebruik buiten het aanbevolen temperatuurbereik en plaatsing naast een warmtebron zal ook de hoeveelheid ijs en interne/externe condensatie doen toenemen. In geval van externe condensatie kunt u het oppervlak afvegen met een doek. Te veel ijs leidt tot langere bedrijfstijden, waardoor het energieverbruik toeneemt en de onderdelen slechter worden. Als de pakking of afdichting beschadigd of vervormd is, zal het energieverbruik toenemen. Vervang de pakking om de efficiëntie te herstellen.
Het schoonmaken van de condensor Filter
• De condensor is onderdeel van het koelsysteem. De condensor filter vereist maandelijkse reiniging.
• Ontkoppel voeding altijd alvorens oktober routineonderhoud.
• Als de condensor filter te reinigen zullen de prestaties en de levensduur van uw Polareenheid te verminderen en kan uw garantie ongeldig.
• Deze modellen hebben een uitneembare filter kan worden gereinigd met een stofzuiger.
Oplossen van problemen
Indien nodig moet een gekwalificeerde technicus reparaties uitvoeren.
Probleem Mogelijke oorzaak Handeling
Het apparaat werkt niet
Het apparaat staat uit Controleer of de stroomkabel van het apparaat is
Stekker en kabel zijn beschadigd
Storing netvoeding Controleer netvoeding
aangesloten en of het apparaat is ingeschakeld Vervang stekker of kabel
11
Page 12
NL
Probleem Mogelijke oorzaak Handeling
Het product staat aan maar de temperatuur is te hoog/laag
Het product lekt water
Het product maakt ongebruikelijk veel lawaai
Teveel ijs in de verdamper Ontdooi het product Condensor wordt geblokkeerd door stof Reinig de condensor Deuren niet goed gesloten Controleren of de deuren goed dicht en of
afdichtingen niet beschadigd zijn
Het product bevindt zich in de nabijheid van een warmtebron of de luchtstroom
Verplaats de koelkast naar een geschiktere locatie
naar de condensor wordt onderbroken Omgevingstemperatuur is te hoog Verbeter de ventilatie of verplaats het
product naar een koelere locatie
Ongeschikte levensmiddelen worden in het product bewaard
Verwijder alle overbodige warme levensmiddelen of deblokkeer de ventilator
Het product wordt overbelast Verminder de hoeveelheid opgeslagen
voedsel in het product
Het product staat niet recht Pas de verstelbare poten aan om het
product te nivelleren (indien nodig) De afvoeropening wordt geblokkeerd Maak de afvoeropening vrij van obstakels De waterstroom naar de afvoer wordt
geblokkeerd De waterbak is beschadigd
Maak de vloer vrij van obstakels (indien
nodig)
Raadpleeg een gekwalificeerde technicus
De druppellade stroomt over Leeg de druppellade (indien nodig) Moer/schroef los Alle moeren en schroeven controleren en
aantrekken Het product is niet op een effen of
stabiele ondergrond geplaatst
Installatielocatie controleren en indien
nodig veranderen
Technische specificaties
Opmerking: Als gevolg van ons voortdurende programma van onderzoek en ontwikkeling, kunnen de specificaties hierin zonder voorafgaande kennisgeving worden gewijzigd.
Model Voltage Vermogen Stroom Temperatuurbereik Inhoud (liters) Koelmiddel
FA854 220-240V~
FA855 110W 0,8A 2°C - 8°C 7 x gastronorm 1/4
FA856 122W 0,8A 2°C - 8°C 8 x gastronorm 1/4
FA857 122W 0,8A 2°C - 8°C 10 x gastronorm 1/4
DA680 110W 0,8A 2°C - 8°C 6 x gastronorm 1/4
12
50Hz
110W 0,8A 2°C - 8°C 5 x gastronorm 1/4
Container
Container
Container
Container
Container
R600a 274 x 1200 x 335 25
R600a 274 x 1500 x 335 29
R600a 274 x 1800 x 335 32
R600a 274 x 2000 x 335 34
R600a 274 x 1400 x 335 27
Afmetingen
h x b x d mm
Gewicht
(kg)
Page 13
NL
Elektrische bedrading
Men dient de stekker op een geschikt stopcontact aan te sluiten.
De bedrading van dit apparaat is als volgt:
• Stroomkabel (bruin) naar de aansluitklem gemarkeerd met L
• Neutraalkabel (blauw) naar de aansluitklem gemarkeerd met N
• Aardekabel (groen/geel) naar de aansluitklem gemarkeerd met E
Dit apparaat moet worden geaard.
Raadpleeg bij twijfel een vakkundige elektricien.
De elektrische isolatiepunten mogen niet worden geblokkeerd. In geval van een nooduitschakeling moeten de isolatiepunten direct toegankelijk zijn.
Afvalverwerking
De EU-richtlijnen vereisen dat koelproducten door gespecialiseerde bedrijven wordt verwerkt die gassen, metalen en plastic componenten verwijderen of recyclen.
Raadpleeg uw plaatselijke afvalverwerkingsbedrijf voor informatie over de verwerking van uw apparaat. Plaatselijke overheden zijn niet verplicht om commerciële koelapparatuur als afval te verwerken maar kunnen u wellicht informeren waar u het apparaat kunt afgeven.
U kunt ook de POLAR-helpdesk bellen voor informatie over landelijke afvalverwerkingsbedrijven in de EU.
Productconformiteit
Het WEEE-logo op dit product of bijbehorende documentatie geeft aan dat het product niet onder huisvuil valt en als zodanig ook niet mag worden verwerkt. Ter preventie van mogelijke gevaren voor de gezondheid van personen en/of voor het milieu, dient men dit product in overeenstemming met het voorgeschreven en milieuveilige recyclingproces als afval te verwerken. Raadpleeg uw productleverancier of uw plaatselijk afvalverwerkingsbedrijf voor meer informatie over de juiste afvalverwerking van dit product.
De onderdelen van POLAR producten hebben strenge producttesten ondergaan om te voldoen aan wettelijke regels en specificaties die door internationale, onafhankelijke en landelijke overheden worden voorgeschreven.
POLAR producten zijn goedgekeurd en voorzien van het volgende symbool:
Alle rechten voorbehouden. Het is verboden om deze handleiding, hetzij volledig of gedeeltelijk, elektronisch of mechanisch
te reproduceren, kopiëren, op opslagmedia op te slaan of op enigerlei wijze over te dragen, zonder voorafgaande
Wij hebben er alles aan gedaan om er zeker van te zijn dat op publicatiedatum van de handleiding alle details correct zijn.
Polar behoudt zich echter het recht om zonder voorafgaande kennisgeving de specificaties te wijzigen.
goedkeuring van POLAR.
13
Page 14
FR
Conseils de sécurité
• Placez l’appareil sur une surface plane, stable.
• L’installation et les éventuelles réparations doivent être confiées à un dépanneur / technicien qualifié. Ne retirez aucun composant ou cache de ce produit.
• Consultez les normes locales et nationales pour vous conformer aux :
- lois sur l’hygiène et la sécurité au travail ;
- codes de bonnes pratiques BS EN ;
- précautions contre le risque d’incendie ;
- réglementations sur les branchements électriques IEE ;
- règlements sur la construction.
• NE PAS nettoyer cet appareil avec un nettoyeur à jet / à pression.
• NE PAS se servir de cet appareil pour stocker des médicaments.
• NE PAS utiliser d’appareils électriques à l’intérieur de l’appareil (ex. chauffages, sorbetières, etc.).
• Cet appareil est réservé exclusivement à une utilisation à l’intérieur.
• Veillez à toujours transporter, stocker et manipuler l’appareil à la verticale et à le déplacer en tenant la base du châssis.
• N’oubliez jamais d’éteindre et de débrancher l’appareil avant de procéder à son nettoyage.
• Gardez les emballages hors de portée des enfants. Débarrassez-vous des emballages conformément aux règlements des autorités locales.
• Un cordon d’alimentation endommagé doit être remplacé par un agent POLAR ou un technicien qualifié recommandé, pour éviter tout danger.
14
Page 15
FR
• Cet appareil n’a pas été concu pour être utilisé par des personnes (enfants inclus) à capacités physiques, sensorielles ou mentales réduites ou ne disposant pas d/una expérience ou de connaissances suffisantes, à moins que lesdites personnes n’aient été formées ou instruites quant à son utilisation, par une personne responsable de leur sécurité.
• POLAR recommande de faire tester régulièrement cet appareil (une fois par an au minimum) par une personne compétente. Le test devrait inclure, entre autres : inspection visuelle, test de polarité, la continuité de masse, test d’isolation et test de fonctionnement.
Attention : Risque d’ incendie
• Ne stockez pas de substances explosives telles que les aérosols avec un propulseur inflammable dans cet appareil.
Attention : Évitez de bloquer toutes les ouvertires d’aération. L’unité ne doit pas être mise dans un box dans aération adéquate.
• Attention : Ne pas utiliser de dispositifs mécaniques ou autres moyens pour accélérer le processus de dégivrage, autre que le fabricant recommandé Ceux par.
• Attention : Ne pas endommager le circuit frigorifique.
• Attention : Ne pas utiliser d’appareils électriques à l’intérieur des compartiments de stockage des aliments de l’appareil.
Introduction
Nous vous invitons à consacrer quelques instants à la lecture attentive de ce mode d’emploi. L’entretien et l’utilisation appropriés de cette machine vous permettront de tirer le meilleur de votre produit POLAR.
Contenu de l’emballage
Les éléments suivants vous sont fournis de série :
• Réfrigérateur ou congélateur POLAR
• Mode d’emploi
POLAR attache une grande importance à la qualité et au service et veille à fournir des produits en parfait état opérationnel, parfaitement intacts au moment de l’emballage. Nous vous prions de contacter votre revendeur POLAR immédiatement si vous constatez un dommage quelconque survenu pendant le transport du produit.
• Barre de séparation Gastronormes
• 4 pieds réglables
15
Page 16
FR
Installation
Remarque : Ne pas utiliser dans des camionnettes ou des semi-remorques, dans des camions-restaurants ou véhicules similaires. Remarque : dans les cas où l’appareil a été stocké ou déplacé autrement qu’à la verticale, placez-le en position debout pendant environ 12 heures avant de vous en servir. En cas de doute, laissez l’appareil se reposer.
1. Sortez l’appareil de l’emballage. Veillez à bien retirer toute la pellicule et les revêtements de protection de toutes les surfaces.
2. Pour optimiser les performances et la longévité, assurez-vous qu’un dégagement minimum de 2,5 cm est maintenu entre l’unité et les murs et autres objets, avec un dégagement minimum de 20 cm sur le dessus. NE JAMAIS
PLACER À PROXIMITÉ D’UNE SOURCE DE CHALEUR.
Remarque : Avant d’utiliser l’appareil pour la première fois, nettoyez l’intérieur avec de l’eau savonneuse et séchez-le bien.
• Mettez l’appareil de niveau en réglant les pieds à vis.
Fonctionnement
Mise en service
1. Vérifiez que l’interrupteur marche / arrêt est réglé sur [O] et allumez la prise.
2. Mettez l’appareil sous tension, position [I]. La température à l’intérieur de l’appareil s’affiche.
Réglez la température de fonctionnement
1. Maintenez le bouton SET pendant 3 secondes. L’affichage clignote.
2. Appuyez sur les boutons afficher la température requise.
3. Appuyez sur le bouton SET pour mémoriser la température.
ou pour
Degivrage manual
Appuyez sur les bouton «aux» et maintenez­le enfonce pendant 2 secondes pour demarrer le degivrage automatique. Le voyant de degivrage s’allume.
Le cycle de dégivrage se termine automatiquement.
Conservation des aliments
Pour obtenir les meilleurs résultats de votre appareil POLAR, suivez ces instructions :
• N’entreposez les denrées alimentaires dans l’appareil qu’après avoir atteint la température de fonctionnement correcte.
• Assurez-vous que les baies gastronorm sont pleines à tout moment, même si les gastronorms sont inutilisés ou vides. Les baies vides réduiront considérablement l’efficacité de l’appareil.
• Utilisez les entretoises fournies pour combler les lacunes (ils ne sont pas tenus de prendre en charge chaque casseroles GN).
• Ne pas obstruer les ventilateurs à l’intérieur de l’appareil.
Remarque : l’appareil n’est pas conçu pour le stockage long terme d’aliments.
16
Page 17
FR
Nettoyage, entretien et maintenance
• N’oubliez jamais d’éteindre et de débrancher l’appareil avant de procéder à son nettoyage.
• Nettoyez l’intérieur de l’appareil aussi souvent que possible.
• N’utilisez aucun produit de nettoyage abrasif. Ces produits peuvent laisser des résidus nocifs.
• Nettoyez le joint de la porte avec de l’eau savonneuse chaude.
• Soyez prudent quand vous nettoyez l’arrière de l’appareil. Les bords effilés peuvent couper.
L’ouverture fréquente et prolongée des portes entraîne la formation de condensation et de glace. Le fait de faire fonctionner l’appareil en dehors de la plage de température recommandée et de le placer à côté d’une source de chaleur augmente également la quantité de glace et de condensation interne/externe. En cas de condensation externe, essuyez la surface avec un chiffon. Une quantité excessive de glace entraînera des temps de fonctionnement plus longs qui augmenteront la consommation d’énergie et la détérioration des composants. Si le joint ou la garniture est endommagé ou déformé, la consommation d’énergie augmentera. Pour rétablir l’efficacité, remplacez le joint d’étanchéité.
Nettoyage du filtre à condensateur
• Le condenseur est la partie du système de réfrigération. Le filtre du condenseur nécessite un nettoyage mensuel.
• Toujours débrancher l’alimentation avant de procéder Octobre entretien courant.
• L’omission de nettoyer le filtre du condenseur permettra de réduire les performances et la durée de vie de votre appareil Polar et peut invalider votre garantie.
• Ces modèles ont un filtre amovible qui peut être nettoyé avec un aspirateur.
Dépannage
Un technicien qualifié doit effectuer les réparations si nécessaire.
Dysfonctionnement Cause probable Intervention
L’appareil ne fonctionne pas
L'appareil n'est pas allumé Vérifier que l'appareil est bien branché et
La fiche ou le câble est endommagé
Défaut d’alimentation secteur Vérifier l’alimentation secteur
allumé Remplacez la fiche ou le câble
17
Page 18
FR
Dysfonctionnement Cause probable Intervention
L’appareil s’allume, mais la température est trop haute / basse
Excès de glace sur l’évaporateur Décongeler l’appareil Le condensateur est saturé de
Nettoyer le condenseur
poussières Les portes sont mal fermées Vérifier que les portes sont fermées et
l’état des joints
L’appareil est situé près d’une source de chaleur ou l’air ne circule pas
Déplacer le réfrigérateur pour le placer à un endroit mieux adapté
librement vers le condensateur Température ambiante trop haute Augmenter la ventilation ou placer
l’appareil à un endroit plus frais
Des aliments inadéquats sont stockés dans l’appareil
Retirer les aliments trop chauds ou les éventuelles obstructions au ventilateur
L’appareil est surchargé Réduire la quantité d’aliments stockés
dans l’appareil
Fuite d’eau L’appareil n’est pas de niveau Régler les pieds à vis pour le mettre de
niveau (le cas échéant) Évacuation bouchée Déboucher l’évacuation Circuit de vidange bouché Nettoyer le plancher de l’appareil (le cas
échéant) Bac à eau endommagé Consulter un technicien qualifié La cuvette de dégivrage déborde Vider la cuvette de dégivrage (le cas
échéant)
L’appareil fait beaucoup de bruit
Écrou / vis desserrés Vérifier et resserrer les écrous et vis La surface sur laquelle l’appareil
a été posé n’est pas de niveau ou
Vérifier la position d’installation et la
changer si nécessaire l’appareil n’est pas stable
Spécifications techniques
Remarque : en raison de notre programme continu de recherche et de développement, les spécifications du présent document peuvent être modifiées sans préavis.
Modèle Tension Puissance Courant
FA854 220-240V~
FA855 110W 0,8A 2°C - 8°C 7 x gastronorm 1/4
FA856 122W 0,8A 2°C - 8°C 8 x gastronorm 1/4
FA857 122W 0,8A 2°C - 8°C 10 x gastronorm 1/4
DA680 110W 0,8A 2°C - 8°C 6 x gastronorm 1/4
18
50Hz
110W 0,8A 2°C - 8°C 5 x gastronorm 1/4
Plage de
température
Capacité (litres) Réfrigérant
Container
Container
Container
Container
Container
R600a 274 x 1200 x 335 25
R600a 274 x 1500 x 335 29
R600a 274 x 1800 x 335 32
R600a 274 x 2000 x 335 34
R600a 274 x 1400 x 335 27
Dimensions
h x l x p mm
Poids
(kg)
Page 19
FR
Raccordement électrique
La prise doit être reliée à la prise secteur qui convient.
Cet appareil est câblé comme suit :
• Fil conducteur (brun) à la borne marquée L
• Fil neutre (bleu) à la borne marquée N
• Fil de terre (vert / jaune) à la borne marquée E
Cet appareil doit être mis à la terre.
En cas de doute, consultez un électricien qualifié.
Les points d’isolation électrique doivent être libres de toute obstruction. En cas de débranchement requis en urgence, ils doivent être facilement accessibles.
Mise au rebut
Les règlements de l’UE exigent que les produits munis de réfrigérants soient mis au rebut par des entreprises spécialisées, équipées pour extraire et recycler les composants à gaz, métalliques et en plastique.
Adressez-vous à votre autorité chargée de la collecte des déchets pour ce qui concerne la mise au rebut de votre appareil. Même si rien n’oblige les autorités locales à se charger de la mise au rebut du matériel de réfrigération commerciale, elles pourraient être en mesure de vous conseiller sur les moyens disponibles localement pour s’en débarrasser.
Vous pouvez aussi appeler le standard d’assistance POLAR, qui saura vous renseigner sur les entreprises de prise en charge nationales au sein de l’UE.
Conformité
Le logo WEEE qui figure sur ce produit ou sa documentation indique qu'il ne doit pas être mis au rebut avec les ordures ménagères. Pour éviter qu'il ne présente un risque pour la santé humaine et / ou écologique, confiez la mise au rebut de ce produit à un site de recyclage agréé respectueux de l'environnement. Pour de plus amples détails sur la mise au rebut appropriée de ce produit, contactez le fournisseur du produit ou l'autorité responsable de l'enlèvement des ordures dans votre région.
Les pièces POLAR ont été soumises à des tests rigoureux pour pouvoir être déclarées conformes aux normes et spécifications réglementaires définies par les autorités internationales, indépendantes et fédérales.
Les produits POLAR ont été déclarés aptes à porter le symbole suivant :
Tous droits réservés. La production ou transmission, partielles ou intégrales, sous quelque forme que ce soit ou par n’importe
quel moyen, tant électronique que mécanique, sous forme de photocopie, d’enregistrement ou autre de ce mode d’emploi
Nous nous efforçons, par tous les moyens dont nous disposons, de faire en sorte que les détails contenus dans le présent mode d’emploi soient corrects en date d’impression. Toutefois, POLAR se réserve le droit de changer les spécifications de
sont interdites sans l’autorisation préalablement accordée par POLAR.
ses produits sans préavis.
19
Page 20
DE
Sicherheitshinweise
• Auf eine flache, stabile Fläche stellen.
• Alle erforderlichen Montage- und Reparaturarbeiten sollten von Wartungspersonal oder einem qualifizierten Techniker durchgeführt werden. Keine Bauteile oder Bedienflächen von diesem Produkt entfernen.
• Für folgende Normen und Vorschriften sind die lokalen und nationalen Normen heranzuziehen:
- Arbeitsschutzvorschriften
- BS EN Verhaltenspraktiken
- Brandschutzvorschriften
- IEE-Anschlussvorschriften
- Bauvorschriften
• Das Gerät NICHT mit einem Strahl-/Hochdruckreiniger reinigen.
• Nur zum Gebrauch in Gebäuden.
• Das Gerät NICHT zum Aufbewahren von medizinischen Produkten verwenden.
• Das Gerät stets aufrecht tragen, lagern und transportieren. Zum Transport den Schrank an der Unterseite anfassen.
• Vor Reinigungsarbeiten stets zunächst das Gerät abschalten und den Netzstecker ziehen.
• Verpackungsmaterial außerhalb der Reichweite von Kindern aufbewahren und gemäß den lokalen Vorschriften entsorgen.
• Aus Sicherheitsgründen muss ein beschädigtes Stromkabel von einem POLAR-Mitarbeiter oder empfohlenen qualifizierten Elektriker erneuert werden.
• Dieses Gerät solte nur dann von Personen (einschlißlich Kindern) mit reduzierten körperlichen, sensorischen oder geistigen Fähigkeiten, mangelnder Erfahrung oder Kenntnissen verwendet werden, wenn sie von einer für ihre Sicherheit verantwortlichen Person im Gebrauch des Geräts geschult wurden bzw. ständig beautsichtigt werden.
20
Page 21
DE
• Polar empfiehlt, dass dieses Gerät regelmäßig (wenigstens jährlich) von einem Fachmann überprüft wird. Die Überprüfung sollte beinhalten, ohne darauf beschränkt zu sein: Visuelle Überprüfung, Polaritätstest, Erdungskontinuität, Isolationskontinuität und Funktionalitätsprüfung.
Vorsicht: Brandgefahr
• Explosive Stoffe wie Sprühdosen mit brennbaren Treibmittel in diesem Gerät nicht speichern.
Warnung: Halten Sie alle Lüftungsöffnungen frei. Das Gerät sollte nicht ohne geeignete Ventilation eingebaut werden.
• Warnung: Verwenden Sie keine mechanischen Vorrichtungen oder andere Mittel, um den Abtauvorgang zu beschleunigen, außer denen die vom Hersteller empfohlen wurden.
• Warnung: Beschädigen Sie den Kältemittelkreislauf nicht.
• Warnung: Verwenden Sie keine elektrischen Geräte innerhalb der Ablagefächer des Geräts, sofern sie nicht der Typ.
Einführung
Bitte nehmen Sie sich einige Minuten Zeit und lesen Sie dieses Handbuch sorgfältig durch. Nur bei korrekter Wartung und vorschriftsgemäßem Betrieb kann Ihr POLAR-Produkt optimale Leistung erzielen.
Lieferumfang
Folgende Teile befinden sich in der Verpackung:
• POLAR-Kühl- oder Tiefkühlgerät
• Bedienungsanleitung
POLAR ist stolz auf die hochwertige Qualität seiner Produkte und seinen erstklassigen Service. Wir stellen sicher, dass alle gelieferten Produkte zum Zeitpunkt der Verpackung voll funktionsfähig sind und sich in einwandfreiem Zustand befinden.
Sollten Sie Transportschäden feststellen, wenden Sie sich bitte unverzüglich an Ihren POLAR-Händler.
• Gastronorm-Adapterstange
• 4 Regulierbare Füße
21
Page 22
DE
Montage
Hinweis: Nicht zur Verwendung in Lieferwagen oder Anhängern, Transportern oder ähnlichen Fahrzeugen. Hinweis: Wenn das Gerät nicht aufrecht transportiert oder gelagert wurde, muss es vor Inbetriebnahme rund 12 Stunden aufrecht aufgestellt werden. Im Zweifelsfall lassen Sie es aufrecht stehen.
1. Gerät aus der Verpackung nehmen. Darauf achten, dass die gesamte Plastikfolie und alle Beschichtungen von sämtlichen Flächen entfernt wurden.
2. Um die Leistung und Langlebigkeit zu optimieren, stellen Sie sicher, dass zwischen dem Gerät und den Wänden und anderen Objekten ein Mindestabstand von 2,5 cm eingehalten wird, wobei oben ein Mindestabstand von 20 cm eingehalten wird. NIEMALS IN DER NÄHE EINER
WÄRMEQUELLE.
Hinweis: Reinigen Sie das Innere des Geräts vor der ersten Inbetriebnahme mit Seifenwasser und trocknen Sie es anschließend gut ab.
• Das Gerät durch Einstellen der Schraubfüße ausgleichen.
Einschalten
1. Darauf achten, dass der Ein-/Ausschalter auf [O] steht und der Netzstecker eingesteckt ist.
2. Das Gerät einschalten [I]. Die momentane Temperatur im Gerät wird angezeigt.
Betriebstemperatur einstellen
1. Halten Sie die SET-Taste für 3 Sekunden gedrückt. Die Anzeige blinkt auf.
2. Drücken Sie die Taste benötigte Temperatur aufzurufen.
3. Zum Speichern der Temperatur drücken Sie die Taste SET.
oder , um die
Manuelles Abtauen
Um den Abatauvorgang zu starten, die taste „aux“ 2 Sekunden lang gedruct halten. Die Abtaulampe leuchtet auf.
Der Abtauzyklus wird automatisch beendet.
Betrieb
Lagern von Lebensmitteln
Um die besten Ergebnisse Ihres POLAR-Gerätes zu erhalten, folgen Sie diesen Anweisungen:
• Lagern Sie nur Lebensmittel im Gerät, wenn es die korrekte Betriebstemperatur erreicht hat.
• Stellen Sie sicher, dass die Gastronorm-Gestelle immer voll sind, auch wenn die Gastronorme nicht verwendet werden oder leer sind. Leere Gestelle verringern die Effizienz des Gerätes erheblich.
• Verwenden Sie die mitgelieferten Abstandhalter, um Lücken zu füllen (sie sind nicht erforderlich, um jede GN-Schale zu halten).
• Versperren Sie nicht die Ventilatoren im Gerät.
Hinweis: Das Gerät ist nicht für die Langzeitlagerung von Lebensmitteln vorgesehen.
22
Page 23
DE
Reinigung, Pflege und Wartung
• Vor Reinigungsarbeiten stets zunächst das Gerät abschalten und den Netzstecker ziehen.
• Den Schrank möglichst häufig innen reinigen.
• Keine Scheuermittel verwenden, da diese schädliche Rückstände hinterlassen können.
• Die Türdichtung mit warmem Seifenwasser reinigen.
• Nach dem Reinigen stets mit einem Tuch trocknen.
• Zur Reinigung verwendetes Wasser darf nicht durch die Ablauföffnung in die Auffangschale gelangen.
• Vorsicht beim Reinigen der Geräterückseite. Scharfe Kanten können zu Verletzungen führen.
Bei häufigem und längerem Öffnen der Türen bilden sich Kondenswasser und Eis. Wenn Sie das Gerät außerhalb des empfohlenen Temperaturbereichs betreiben und es in der Nähe einer Wärmequelle aufstellen, erhöht sich ebenfalls die Menge an Eis und interner/ externer Kondensation. Bei äußerer Kondensation wischen Sie die Oberfläche mit einem Tuch ab. Übermäßige Vereisung führt zu längeren Laufzeiten, die den Energieverbrauch erhöhen und den Verschleiß der Komponenten beschleunigen. Wenn die Dichtung beschädigt oder verformt ist, erhöht sich der Energieverbrauch. Um die Effizienz wiederherzustellen, die Dichtung ersetzen.
Reinigung der Filter-Kondensator
• Der Kondensator ist Teil des Kühlsystems. Der Kondensator­Filter erfordert monatliche Reinigung.
• Trennen Sie Netzteil, bevor Oktober Regelmäßige Wartung.
• Bei Nichtbeachtung der Kondensatorfilter reinigen die Leistung und Lebensdauer Ihres Polar Einheit zu reduzieren und kann Ihre Garantie ungültig.
• Diese Modelle haben einen abnehmbaren Filter, der kann mit einem Staubsauger gereinigt werden.
Störungssuche
Falls erforderlich, muss ein qualifizierter Techniker Reparaturen durchführen.
Störung Vermutliche Ursache Lösung
Das Gerät funktioniert nicht
Das Gerät ist nicht eingeschaltet
Stecker und Kabel sind beschädigt
Fehler Netzstromversorgung
Prüfen, ob der Netzstecker in die Steckdose gesteckt wurde und das Gerät eingeschaltet ist
Stecker oder Leitung ersetzen
Netzstromversorgung prüfen
23
Page 24
DE
Störung Vermutliche Ursache Lösung
Das Gerät lässt sich einschalten, aber die Temperatur ist zu hoch/niedrig
Aus dem Gerät läuft Wasser aus
Das Gerät ist ungewöhnlich laut
Zu viel Eis auf dem Verdampfer Das Gerät abtauen Kondensator verstaubt Reinigen Sie den Kondensator Türen sind nicht richtig geschlossen Prüfen, ob die Türen geschlossen und die
Dichtungen intakt sind
Gerät befindet sich in der Nähe einer Wärmequelle, oder der Luftstrom
Den Kühlschrank an einem geeigneteren Ort aufstellen
zum Kondensator ist unterbrochen Umgebungstemperatur ist zu hoch Belüftung intensivieren oder Gerät an
einem kühleren Ort aufstellen
Ungeeignete Nahrungs-mittel werden im Gerät aufbewahrt
Einige heiße Nahrungsmittel herausnehmen oder Produkte, die den Lüfter blockieren,
entfernen Gerät ist überlastet Weniger Nahrungsmittel im Gerät lagern Das Gerät steht nicht gerade Die Schraubfüße so regulieren, dass das
Gerät eben steht (sofern zutreffend) Der Ablauf ist verstopft Den Ablauf säubern Wasser kann nicht ablaufen Den Boden des Geräts von Fremdstoffen
reinigen (sofern zutreffend) Der Wasserbehälter ist beschädigt Wenden Sie sich an einen qualifizierten
Techniker Die Tropfschale fließt über Die Tropfschale leeren (sofern zutreffend) Alle Muttern und Schrauben
überprüfen und anziehen Das Gerät steht nicht eben oder stabil
Alle Muttern und Schrauben überprüfen
und anziehen
Position überprüfen und bei Bedarf ändern
Technische Spezifikationen
Hinweis: Aufgrund unseres kontinuierlichen Forschungs- und Entwicklungsprogramms können sich die hier aufgeführten Spezifikationen ohne vorherige Ankündigung ändern.
Modell Spannung Leistung Stromstärke
FA854 220-240V~
FA855 110W 0,8A 2°C - 8°C 7 x gastronorm 1/4
FA856 122W 0,8A 2°C - 8°C 8 x gastronorm 1/4
FA857 122W 0,8A 2°C - 8°C 10 x gastronorm 1/4
DA680 110W 0,8A 2°C - 8°C 6 x gastronorm 1/4
24
50Hz
110W 0,8A 2°C - 8°C 5 x gastronorm 1/4
Temperatur-
bereich
Füllmenge Kühlmittel
Container
Container
Container
Container
Container
R600a 274 x 1200 x 335 25
R600a 274 x 1500 x 335 29
R600a 274 x 1800 x 335 32
R600a 274 x 2000 x 335 34
R600a 274 x 1400 x 335 27
Abmessungen
h x b x t mm
Gewicht
(kg)
Page 25
DE
Elektroanschlüsse
Der Stecker muss in eine geeignete Steckdose gesteckt werden.
Das Gerät ist wie folgt verdrahtet:
• Stromführender Leiter (braun) an Klemme L
• Neutralleiter (blau) an Klemme N
• Erdleiter (grün/gelb) an Klemme E
Dieses Gerät muss geerdet sein.
Bei Fragen wenden Sie sich bitte an einen qualifizierten Elektriker.
Elektroisolierpunkte dürfen nicht blockiert werden. Bei einem Notstopp müssen diese Punkte jederzeit sofort zugänglich sein.
Entsorgung
Gemäß EU-Vorschriften müssen Kühlprodukte von Fachunternehmen entsorgt werden, die alle Gase, Metall- und Kunststoffbauteile entfernen oder recyceln.
Ihre Kommunalverwaltung kann Sie über die Entsorgung Ihres Geräts informieren. Kommunalbehörden sind nicht verpflichtet, gewerbliche Kühlgeräte zu entsorgen. Sie können Sie jedoch über lokale Annahmestellen informieren, die diese Geräte entsorgen.
Oder rufen Sie die POLAR-Helpline an. Wir verfügen über eine Liste nationaler Entsorger in den EU­Staaten.
Konformität
Das WEEE-Logo an diesem Produkt oder in der Dokumentation weist darauf hin, dass das Produkt nicht mit dem normalen Hausmüll entsorgt werden darf. Um potenziellen Gesundheits- bzw. Umweltschäden vorzubeugen, muss das Produkt durch einen zugelassenen und umweltverträglichen Recyclingprozess entsorgt werden. Ausführliche Informationen zur korrekten Entsorgung dieses Produkts erhalten Sie von Ihrem Produktlieferanten oder der für die Müllentsorgung in Ihrer Region zuständige Behörde.
Alle POLAR-Produkte werden strengen Tests unterzogen, um die Einhaltung von Normen und Spezifikationen internationaler und nationaler Behörden und unabhängiger Organisationen zu gewährleisten.
POLAR-Produkte dürfen durch folgendes Symbol gekennzeichnet werden:
Alle Rechte vorbehalten. Diese Anleitung darf ohne vorherige schriftliche Genehmigung von POLAR weder ganz noch
teilweise in irgendeiner Form oder auf irgendeinem Wege - einschließlich elektronischer, mechanischer Verfahren, durch
Es werden alle Anstrengungen unternommen um sicherzustellen, dass alle Angaben bei der Drucklegung korrekt sind.
Fotokopieren, Aufnahme oder andere Verfahren - vervielfältigt oder übertragen werden.
POLAR behält sich jedoch das Recht vor, Spezifikationen ohne Vorankündigung zu ändern.
25
Page 26
IT
Suggerimenti per la sicurezza
• Posizionare il fabbricatore di ghiaccio su una superficie in piano e stabile.
• L’installazione e le eventuali riparazioni devono venire eseguite da un agente/tecnico qualificato. Non rimuovere i componenti o i pannelli di accesso dell’apparecchio.
• Verificare la conformità alle normative locali e nazionali di quanto segue:
- Normativa antinfortunistica sul lavoro
- Linee guida BS EN
- Precauzioni antincendio
- Normativa IEE sui circuiti elettrici
- Norme di installazione
• NON utilizzare sistemi di lavaggio a getto o pressione per pulire l’apparecchio.
• Per esclusivo uso in ambienti chiusi.
• NON utilizzare l’apparecchio per conservare presidi medico­sanitari.
• Trasportare, immagazzinare e movimentare l’apparecchio sempre in posizione verticale e spostarlo mantenendone la base.
• Spegnere e disconnettere l’alimentazione dell’unità prima di pulirla.
• Tenere lontano l’imballaggio dalla portata dei bambini. Smaltire l’imballaggio in conformità alle normative locali.
• Se danneggiato, il cavo di alimentazione deve venire sostituito da un agente POLAR o da un tecnico qualificato al fine di prevenire eventuali rischi.
• L’apparecchio non è destinato a essere utilizzato da persone (inclusi i bambini) con ridotte capacita fisiche, sensoriali o mentali, o prive della necessaria esperienza e conoscenza dell’apparecchio, che non abbiano ricevuto supervisione o istruzioni relative all’utilizzo dell’apparecchio dalle persone responsabili dello loro sicurezza.
26
Page 27
IT
• POLAR raccomanda che questo apparecchio venga periodicamente testato (almeno una volta all’anno) da una persona competente. I test dovrebbero includere, ma non solo: ispezione visiva, test di polarità, continuità di terra, continuità di isolamento e test funzionale.
Attenzione: Rischio di incendio
• Non conservare sostanze esplosive, come bombolette spray con propellente infiammabile in questo apparecchio.
Attenzione: Tenere libere tutte le aperture di ventilazione. L’unità non deve essere installata senza una ventilazione adeguata.
• Attenzione: non utilizzare dispositivi meccanici o altri mezzi per accelerare il processo di sbrinamento, diversa dal fabbricante raccomandato Quelli da.
• Attenzione: Non danneggiare il circuito refrigerante.
• Attenzione: Non usare apparecchi elettrici all’interno degli scomparti per la conservazione degli alimenti.
Introduzione
Leggere con attenzione il presente manuale. La manutenzione e l’utilizzo corretti di questo apparecchio consentiranno di ottenere le massime prestazioni da questo prodotto POLAR.
Contenuto dell’imballaggio
L’imballaggio contiene quanto segue:
• Frigorifero o congelatore POLAR
• Manuale di istruzioni
POLAR garantisce una qualità e un servizio impeccabili e assicura che al momento dell’imballaggio tutti i componenti forniti sono integralmente funzionanti e privi di difetti.
Nel caso siano rilevati danni risultanti dal trasporto del prodotto, rivolgersi immediatamente al rivenditore POLAR locale.
• Separatori gastronorm
• Piedi regolabili 4x
27
Page 28
IT
Installazione
Nota: Non per l’uso in furgoni o rimorchi, camion per il trasporto del cibo o veicoli simili. Nota: se l’apparecchio è stato immagazzinato o spostato in posizione non verticale, lasciarlo in posizione verticale per circa 12 ore prima di metterlo in funzione. In caso di dubbio, osservare comunque questa precauzione.
1. Rimuovere l’apparecchio dall’imballaggio. Assicurarsi che la pellicola protettiva e rivestimenti in plastica siano interamente rimossi da tutte le superfici.
2. Per ottimizzare le prestazioni e la longevità, assicurarsi che sia mantenuta una distanza minima di 2,5 cm tra l’unità e le pareti e altri oggetti, con una distanza minima di 20 cm nella parte superiore. NON POSIZIONARE
MAI VICINO A UNA FONTE DI CALORE.
Nota: prima di utilizzare l’apparecchio per la prima volta, pulire l’interno con acqua saponata e asciugare bene.
3. Mettere in piano l’apparecchio regolando i piedi.
Accensione
1. Assicurarsi che l’interruttore dell’alimentazione sia impostato su [O] e acceso alla presa.
2. Accendere l’alimentazione [I]. Viene visualizzata la temperatura corrente all’interno dell’apparecchiatura.
Impostazione della temperatura di esercizio
1. Tenere premuto il pulsante SET per 3 secondi. Il display lampeggia..
2. Premere i pulsanti la temperatura richiesta.
3. Premere il pulsante SET per memorizzare la temperatura.
or per visualizzare
Sbrinamento manuale
Premere senza rilasciare il pulsante aux per 2 secondi per avviare lo sbrinamento. La spia di sbrinamento si accende.
Funzionamento
Conservazione cibo
Per avere i migliori risultati dallo strumento POLAR, seguire le istruzioni:
• Conservare alimenti nello strumento solamente quando ha raggiunto la corretta temperatura di funzionamento.
• Assicurarsi che i gastronorm siano pieni sempre, anche se sono inutilizzati o vuoti. Gli scomparti vuoti riducono di molto l’efficienza dello strumento.
• Usare le barre distanziatrici fornite per riempire gli spazi (non si richiede di supportare ogni teglia GN).
• Non ostruire le ventole all’interno dello strumento.
Nota: l’apparecchio non destinato alla conservazione a lungo termine di alimenti.
28
Il ciclo di sbrinamento si conclude automaticamente.
Page 29
IT
Pulizia e manutenzione
• Prima di eseguire la pulizia, spegnere e scollegare l’alimentazione.
• Pulire l’interno dell’apparecchio quanto più spesso possibile.
• Non utilizzare detergenti abrasivi in quanto possono lasciare residui nocivi.
• Pulire la tenuta della porta con acqua calda saponata.
• Asciugare sempre dopo la pulizia.
• Non permettere che l’acqua utilizzata per la pulizia penetri attraverso il foro di scarico nella vasca di evaporazione.
• Prestare attenzione durante la pulizia della parte posteriore dell’apparecchio. Gli attrezzi con bordi taglienti possono provocare tagli.
Con l’apertura frequente e prolungata delle porte si formano condensa e ghiaccio. Anche il funzionamento al di fuori dell’intervallo di temperatura consigliato e la collocazione vicino a una fonte di calore aumentano la formazione di ghiaccio e di condensa interna/ esterna. In caso di condensa esterna, pulire la superficie con un panno. L’eccesso di ghiaccio provoca tempi di funzionamento più lunghi che aumentano il consumo energetico e il deterioramento dei componenti. Se la guarnizione o la tenuta sono danneggiate o deformate, il consumo energetico aumenta. Per ripristinare l’efficienza, sostituire la guarnizione.
Pulizia del filtro condensatore
• Il condensatore è parte del sistema di refrigerazione. Il filtro del condensatore richiede una pulizia mensile.
• Scollegare sempre l’alimentazione prima di effettuare la manutenzione ordinaria.
• La mancata pulizia del filtro del condensatore riduce le prestazioni e la durata dell’unità Polar e può invalidare la garanzia.
• Questi modelli dispongono di un filtro removibile che può essere pulita con un aspirapolvere.
Risoluzione dei problemi
Se necessario, un tecnico qualificato deve eseguire le riparazioni.
Guasto Probabile causa Azione
L’apparecchio non funziona
L'apparecchio non è acceso Controllare che l'apparecchio sia correttamente collegato e
La presa e il cavo sono danneggiati
Guasto alimentazione di rete
acceso Sostituire la spina o il cavo
Controllare l’alimentazione di rete
29
Page 30
IT
Guasto Probabile causa Azione
L’apparecchi si accende ma la temperatura è troppo alta o troppo bassa
L’apparecchio perde acqua
L’apparecchio presenta una rumorosità eccessiva
Quantità eccessiva di ghiaccio
Sbrinare l’apparecchio
nell’evaporatore Il condensatore è bloccato dalla
Pulire il condensatore
polvere I portelli non sono chiusi in maniera
appropriata
Controllare che i portelli siano chiusi e che le guarnizioni di tenuta non siano danneggiate
L’apparecchio è posizionato in prossimità di una sorgente di
Spostare il frigorifero in una posizione più
appropriata calore oppure il flusso di aria al condensatore è interrotto
La temperatura ambientale è troppo alta
Sono stati conservati nell’apparecchio cibi non appropriati
Aumentare la ventilazione oppure spostare
l’apparecchio in una posizione più fresca
Rimuovere i cibi eccessivamente caldi o le
ostruzioni della ventola L’apparecchio è sovraccarico Ridurre la quantità dei cibi presenti
nell’apparecchio L’apparecchio non è in posizione
piana
Regolare i piedi al fine di mantenere in
piano l’apparecchio (se pertinente) La bocca di scarico è bloccata Pulire la bocca di scarico Il movimento dell’acqua verso lo
scarico è ostruito Il contenitore dell’acqua è
Pulire il pavimento dell’apparecchio (se
pertinente)
Consultare un tecnico qualificato danneggiato
La vaschetta di raccolta dell’acqua di sbrinamento è troppo piena
Svuotare la vaschetta di raccolta dell’acqua
di sbrinamento (se pertinente) Dadi o viti allentati Controllare e serrare tutti i dadi e le viti L’apparecchio non è stato installato
in una posizione in piano o stabile
Controllare la posizione di installazione e
modificarla se necessario
Specifiche tecniche
Nota: a causa del nostro continuo programma di ricerca e sviluppo, le specifiche qui riportate possono essere soggette a modifiche senza preavviso.
Modello Tensione Tensione Corrente
FA854 220-240V~
FA855 110W 0,8A 2°C - 8°C 7 x gastronorm 1/4
FA856 122W 0,8A 2°C - 8°C 8 x gastronorm 1/4
FA857 122W 0,8A 2°C - 8°C 10 x gastronorm 1/4
DA680 110W 0,8A 2°C - 8°C 6 x gastronorm 1/4
30
50Hz
110W 0,8A 2°C - 8°C 5 x gastronorm 1/4
Intervallo di
temperatura
Capacità
Container
Container
Container
Container
Container
Refrige-
rante
R600a 274 x 1200 x 335 25
R600a 274 x 1500 x 335 29
R600a 274 x 1800 x 335 32
R600a 274 x 2000 x 335 34
R600a 274 x 1400 x 335 27
Dimensioni
h x l x p mm
Peso
(kg)
Page 31
IT
Cablaggi elettrici
La spina deve venire collegata a una presa di rete appropriata.
L’apparecchio ha i seguenti cablaggi:
• Filo sotto tensione (colore marrone) a terminale L
• Filo del neutro (colore blu) a terminale N
• Filo di terra (colore verde/giallo) a terminale E
Questa apparecchiatura deve essere collegata a terra.
In caso di dubbi, consultare un elettricista qualificato.
I punti di isolamento elettrico devono essere liberi da ostruzioni. In caso di emergenza, i punti devono essere facilmente raggiungibili qualora sia necessario scollegarli.
Smaltimento
Le normative UE prevedono che lo smaltimento dei prodotti di refrigerazione sia eseguito da aziende specializzate nella rimozione o nel riciclaggio di tutti i gas e dei componenti in metallo e plastica.
Rivolgersi all’ente locale incaricato per informazioni sullo smaltimento di questo apparecchio. Gli enti locali non hanno l’obbligo di procedere allo smaltimento di apparecchi di refrigerazione commerciali ma sono in grado di fornire suggerimenti sulla modalità di smaltimento di tali apparecchi.
In alternativa, chiamare la helpline telefonica di POLAR per ricevere informazioni dettagliate sulle aziende di smaltimento nella UE.
Conformità
Il logo WEEE riportato su questo prodotto o sulla relativa documentazione indica che il prodotto non può essere smaltito come normale rifiuto domestico. Per evitare possibili danni alla salute e/o all'ambiente, il prodotto deve venire smaltito utilizzando una procedura di riciclaggio approvata e sicura per l'ambiente. Per ulteriori informazioni su come smaltire in maniera corretta questo prodotto, contattare il fornitore del prodotto o l'ente locale responsabile per lo smaltimento dei rifiuti.
I componenti POLAR sono stati sottoposti a un rigoroso collaudo ai fini della conformità agli standard e alle specifiche normative previste dalle autorità internazionali, indipendenti e federali.
I prodotti POLAR sono autorizzati a esporre il seguente simbolo:
Tutti i diritti riservati. È vietata la riproduzione o la trasmissione in alcuna forma, elettronica, meccanica, mediante
fotocopiatura o altro sistema di riproduzione, di qualsiasi parte delle presenti istruzioni senza la previa autorizzazione
Le informazioni contenute sono corrette e accurate al momento della stampa, tuttavia POLAR si riserva il diritto di
modificare le specifiche senza preavviso.
scritta di POLAR.
31
Page 32
ES
Consejos de Seguridad
• Colóquela sobre una superficie plana, estable.
• Un agente de servicio / técnico cualificado debería llevar a cabo la instalación y cualquier reparación si se precisa. No retire ningún componente ni panel de servicio de este producto.
• Consulte las Normas Locales y Nacionales correspondientes a lo siguiente:
- Legislación de Seguridad e Higiene en el Trabajo
- Códigos de Práctica BS EN
- Precauciones contra Incendios
- Normativos de Cableado de la IEE
- Normativas de Construcción
• No utilice dispositivos de lavado de chorro / presión para limpiar el aparato.
• Sólo adecuado para uso en interiores.
• NO utilice este aparato para almacenar existencias médicas.
• Siempre debe transportar, almacenar y manipular el aparato verticalmente y moverlo cogiéndolo de la base.
• Desconecte la máquina y desenchúfela del suministro eléctrico de la unidad siempre antes de llevar a cabo la limpieza.
• Mantenga el embalaje lejos del alcance de los niños. Deshágase del embalaje de acuerdo con las normativas de las autoridades locales.
• Si el cable eléctrico está dañado, debe ser reemplazado por un agente de POLAR o un técnico cualificado recomendado para evitar cualquier riesgo.
• Este aparato ne debe ser utilizado por personas (niños incluidos) que tengan limitadas sus capacidades fisicas, senoriales o mentales que no tengan experiencia y conocimientos, a menos que estén bajo la supervision o hayan recibido instrucciones relatives al uso del aparato a cargo de una resona responsable de su seguridad.
32
Page 33
ES
• POLAR recomienda que este aparato debe ser periódicamente probado (al menos anualmente) por una Persona Competente. La prueba debe incluir, pero no debe estar limitado a: Inspección visual, Prueba de polaridad, Toma a tierra, continuidad de aislamiento y prueba Funcional.
Precaución: Riesgo de Incendio
• No guarde sustancias explosivas, tales como latas de aerosol con un propelente inflamable en este aparato.
Advertencia: Mantenga los orificios de ventilación libres de obstrucciones. Asegúrese de que la unidad disponga de una ventilación adecuada.
• Advertencia: No utilice dispositivos mecánicos u otros medios para acelerar el proceso de descongelación, que no sea el fabricante recomienda Aquellos por.
• Advertencia: No dañe el circuito refrigerante.
• Advertencia: No utilice aparatos eléctricos dentro de los compartimentos de almacenamiento de alimentos del aparato.
Introducción
Tómese unos minutos para leer este manual. El correcto mantenimiento y manejo de esta máquina proporcionará el mejor funcionamiento posible de su producto POLAR.
Contenido del Conjunto
Se incluye lo siguiente:
• Frigorífico o Congelador POLAR
• Manual de instrucciones
POLAR se enorgullece de su calidad y servicio y asegura que en el momento del embalaje, el contenido se suministró con plena funcionalidad y sin ningún defecto.
Si encontrara algún daño resultante del transporte, póngase en contacto inmediatamente con su distribuidor POLAR.
• Barra adaptadora Gastranorm
• Patas ajustables x 4
33
Page 34
ES
Instalación
Nota: No debe utilizarse en furgonetas o remolques, camiones de alimentos o vehículos similares. Nota: Si el aparato no se ha almacenado o transportado en posición vertical, déjelo en posición vertical durante aproximadamente 12 horas antes del funcionamiento. Si tiene alguna duda, deje el aparato en posición vertical.
1. Desembale el aparato. Asegúrese de que todos los revestimientos y las láminas de plástico de protección se hayan quitado totalmente de todas las superficies.
2. Para optimizar el rendimiento y la longevidad, asegúrese de que se mantenga un espacio libre mínimo de 2,5 cm entre la unidad y las paredes y otros objetos, con un espacio mínimo de 20 cm en la parte superior. NUNCA UBICAR
AL LADO DE UNA FUENTE DE CALOR.
Nota: Antes de utilizar el aparato por primera vez, limpie el interior con agua jabonosa y luego séquelo bien.
3. Nivele el aparato ajustando la pata enroscada.
Funcionamiento
Activación
1. Asegúrese de que el interruptor de activación esté ajustado en [O] y conéctelo a la toma.
2. Conecte la Alimentación [I]. Se muestra la temperatura actual en el aparato.
Ajuste de la Temperatura de Funcionamiento
1. Mantenga presionado el botón SET durante 3 segundos. El visualizador se enciende.
2. Pulse el botón visualizar la temperatura deseada.
3. Pulse el botón SET para fijar la temperatura.
o los botones para
Descongelacion manual
Pulse y mantenga pulsado el boton aux durante 2 segundos para que empiece la descongelacion . La luz de descongelacion se iluminare.
El ciclo de descongelación finalizará automáticamente.
Almacenamiento de alimentos
Para obtener los mejores resultados de su aparato POLAR, siga estas instrucciones:
• Almacene los productos alimenticios en el aparato sólo cuando haya alcanzado la temperatura de funcionamiento correcta.
• Asegúrese de que las estanterías internas estén llenas en todo momento, incluso si no se utilizan o están vacías. Las estanterías vacías reducirán en gran medida la eficiencia del aparato.
• Utilice las barras espaciadoras proporcionadas para llenar cualquier hueco (no se requiere que apoyen cada una de las bandejas GN).
• No obstruya los ventiladores dentro del aparato.
Nota: El aparato no está diseñado para almacenamiento de alimentos a largo plazo.
34
Page 35
ES
Limpieza, Cuidado y Mantenimiento
• Desconecte la máquina y desenchúfela de la toma eléctrica antes de llevar a cabo la limpieza.
• Limpie el interior del aparato con la mayor frecuencia posible.
• No utilice productos de limpieza abrasivos. Estos pueden dejar residuos nocivos.
• Limpie el sello de la puerta con agua tibia y jabón.
• Limpie el sello de la puerta con agua tibia y jabonosa.
• No permita que el agua utilizada en la limpieza pase por el agujero de desagüe hacia el recipiente de evaporación.
• Vaya con cuidado al limpiar la parte trasera del aparato. Los bordes afilados pueden cortar.
La condensación y el hielo se formarán con la apertura frecuente y prolongada de las puertas. El funcionamiento fuera del rango de temperatura recomendado y la colocación junto a una fuente de calor también aumentarán la cantidad de hielo y la condensación interna/externa. Si se produce condensación externa, limpie la superficie con un paño. El exceso de hielo provocará tiempos de funcionamiento más largos que aumentarán el consumo de energía y el deterioro de los componentes. Si la junta o el sello están dañados o deformados, aumentará el consumo de energía. Para restablecer la eficiencia, sustituya la junta.
Limpieza del filtro de condensador
• El condensador es parte del sistema de refrigeración. El filtro condensador requiere una limpieza mensual.
• Desconecte siempre la fuente de alimentación antes de llevar a cabo mantenimiento rutinario.
• Si no se limpia el filtro de condensador reducirá el rendimiento y la vida útil de la unidad Polar y puede invalidar su garantía.
• Estos modelos tienen un filtro extraíble que se puede limpiar con una aspiradora.
Resolución de problemas
Un técnico calificado debe realizar las reparaciones si es necesario.
Fallo Causa probable Acción
El aparato no funciona
El aparato no está conectado Compruebe que el aparato esté enchufado
El enchufe y el cable están dañados
Fallo de la fuente de alimentación de red
correctamente y conectado Reemplace el enchufe o el cable
Compruebe la fuente de alimentación de red
35
Page 36
ES
El aparato se activa, pero la temperatura es demasiado alta / baja
Hay fugas de agua en el aparato
El aparato es inusualmente ruidoso
Fallo Causa probable Acción
Hay demasiado hielo en el evaporador
Descongele el aparato Condensador bloqueado con polvo Limpie el condensador Las puertas no están bien cerradas Compruebe que las puertas estén cerradas
y las juntas no estén dañadas El aparato se encuentra cerca de
una fuente de calor o el caudal
Traslade el frigorífico a un lugar más
adecuado de aire hacia el condensador está siendo interrumpido
La temperatura ambiente es demasiado alta
Se guardan alimentos no adecuados en el aparato
Aumente la ventilación o traslade el
aparato a un lugar más fresco
Retire cualquier exceso de alimentos
calientes u obstrucciones del ventilador El aparato está sobrecargado Reduzca la cantidad de alimentos
guardados en el aparato El aparato no está bien nivelado Ajuste las patas enroscadas para nivelar el
aparato (si es aplicable) La salida de descarga está
Limpie la salida de descarga bloqueada
El movimiento del agua hacia el
Limpie la base del aparato (si es aplicable) desagüe está obstruido
El contenedor de agua está dañado Consulte a un técnico cualificado La bandeja de goteo está rebosando Vacíe la bandeja de goteo (si es aplicable) Tuerca / tornillo flojo Compruebe y apriete todos los tornillos y
las tuercas El aparato no se ha instalado en una
posición estable o nivelada
Compruebe la posición de la instalación y
cámbiela si es necesario
Especificaciones Técnicas
Modelo Tensión Potencia Corriente
FA854 220-240V~
FA855 110W 0,8A 2°C - 8°C 7 x gastronorm
FA856 122W 0,8A 2°C - 8°C 8 x gastronorm
FA857 122W 0,8A 2°C - 8°C 10 x gastronorm
DA680 110W 0,8A 2°C - 8°C 6 x gastronorm
36
50Hz
110W 0,8A 2°C - 8°C 5 x gastronorm
Margen de
Temperaturas
Capacidad
(litros)
1/4 Container
1/4 Container
1/4 Container
1/4 Container
1/4 Container
Refrigerante
R600a 274 x 1200 x 335 25
R600a 274 x 1500 x 335 29
R600a 274 x 1800 x 335 32
R600a 274 x 2000 x 335 34
R600a 274 x 1400 x 335 27
Dimensiones a x a x p mm
Peso
(kg)
Page 37
ES
Cableado Eléctrico
El enchufe tiene que conectarse a una toma eléctrica adecuada.
Este aparato está conectado de la forma siguiente:
• Cable cargado (de color marrón) al terminal marcado como L
• Cable neutro (de color azul) al terminal marcado como N
• Cable de tierra (de color verde / amarillo) al terminal marcado como E
Este aparato debe conectarse a una toma de tierra.
Si tiene alguna duda, consulte a un electricista cualificado.
Los puntos de aislamiento eléctrico deben mantenerse libres de cualquier obstrucción. En caso de precisarse una desconexión de emergencia, deben estar disponibles de forma inmediata.
Desecho
Las normativas de la UE requieren que los productos de refrigeración sean desechados por compañías especializadas que extraigan o reciclen todos los gases, componentes metálicos y de plástico.
Consulte a su autoridad local de recogida de residuos a la hora de desechar su aparato. Las autoridades locales no están obligadas a eliminar los equipos de refrigeración comerciales pero pueden ofrecer consejo sobre cómo desechar los equipos localmente.
Otra opción es llamar a la línea de asistencia de POLAR para pedir información sobre las compañías nacionales de desechos de la UE.
Cumplimiento
El logotipo WEEE en este producto o su documentación indica que no debe eliminarse como un residuo doméstico. Para ayudar a prevenir posibles daños a la salud humana y/ o el medio ambiente, el producto debe eliminarse en un proceso de reciclaje aprobado y medioambientalmente seguro. Para obtener más información sobre cómo eliminar correctamente este producto, póngase en contacto con el proveedor del mismo o la autoridad local responsable de la eliminación de residuos en su zona.
Las piezas POLAR han pasado estrictas pruebas de productos para cumplir las especificaciones y normas reguladoras establecidas por las autoridades internacionales, independientes y federales.
Los productos POLAR han sido autorizados para llevar el símbolo siguiente:
Reservados todos los derechos. Puede estar prohibida la reproducción o transmisión en cualquier forma o por cualquier
medio electrónico, mecánico, de fotocopiado, registro o de otro tipo, de cualquier parte de estas instrucciones sin la
Se ha hecho todo lo posible para garantizar que todos los datos son correctos en el momento de su publicación; sin
embargo,POLAR se reserva el derecho a modificar las especificaciones sin que medie notificación previa.
autorización previa y por escrito de POLAR.
37
Page 38
DECLARATION OF CONFORMITY
• Conformiteitsverklaring • Déclara�on de conformité • Konformitätserklärung • Dichiarazione di conformità •
Equipment Type • Uitrusngstype • Type d'équipement • Gerätetyp
• Tipo di apparecchiatura • Tipo de equipo
Model • Modèle • Modell • Modello
• Modelo
G-Series Countertop Prep Fridge
10 x ¼ GN
(with stainless steel lids:)
10 x ¼ GN
9 x 1/3 GN
G611 (& -E -A)
FA857 (& -E -A)
GD878 (& -E -A)
Applica�on of Territory
Machinery Direc�ve 2006/42/EC
Equipment Regula�ons 2012 (S.I. 2012/3032)
Electrical Safety
Producer Name • Naam fabrikant • Nom du producteur • Name des Herstellers
• Nome del produore • Nombre del fabricante
Polar
Date • Data • Date • Datum • Data •
Fecha
11th April 2023
Signature • Handtekening •
Full Name • Volledige naam • Nom
Nome completo • Nombre completo
Ashley Hooper
Eoghan Donnellan
Brendan Denmeade
Posi�on • Funce • Foncon •
Technical & Quality
Commercial
Commercial Manager/ Responsible
Producer Address • Adres fabrikant •
fabricante
Fourth Way,
United Kingdom
Unit 9003,
Ireland
• Declaración de conformidad
5 x ¼ GN 6 x ¼ GN 7 x ¼ GN 8 x ¼ GN
Legisla�on & Council Direc�ves(s)
Toepassing van Europese Richtlijn(en) • Applicaon de la/des direcve(s) du Conseil
• Anwendbare EU­Richtlinie(n) • Applicazione delle Direve
• Aplicación de la(s) direcva(s) del consejo •
I, the undersigned, hereby declare that the equipment specified above conforms to the above Territory Legisla�on, Direc�ve(s) and Standard(s).
Ik, de ondergetekende, verklaar hierbij dat de hierboven gespeciceerde uitrusg goedgekeurd is volgens de bovenstaande Richtlijn(en) en Standaard(en). Je soussigné, conrme la conformité de l'équipement cité dans la présente à la / aux Direve(s) et Norme(s) ci-dessus Ich, der/die Unterzeichnende, erkläre hiermit, dass das oben angegebene Gerät der/den oben angef entspricht. Il sooscrio dichiara che l'apparecchiatura di sopra specicata è conforme alle Direve e agli Standard sopra riport. El abajo rmante declara por la presente que el equipo arriba especicado está en conformidad con la(s) direva(s) y estándar(es) arriba mencionadas.
5 x ¼ GN 6 x ¼ GN 7 x ¼ GN 8 x ¼ GN
Supply of Machinery (Safety) Regula�ons 2008
(BS) EN 60335-1:2012 +A11:2014 +A13:2017 (BS) EN 60335-2-89:2010 +A1:2016 +A2:2017
3 x 1/3 GN & 1 x ½ GN 4 x 1/3 GN & 1 x ½ GN 5 x 1/3 GN & 1 x ½ GN 8 x 1/3 GN
(BS) EN 62233:2008
Electro-Magne�c Compa�bility (EMC) Direc�ve 2014/30/EU - recast of 2004/108/EC
Electromagne�c Compa�bility Regula�ons 2016 (S.I. 2016/1091)
(BS) EN IEC 55014-1:2021 (BS) EN IEC 55014-2:2021 (BS) EN IEC 61000-3-2: 2019 +A1:2021 (BS) EN 61000-3-3: 2013 +A1:2019 +A2:2021
Restric�on of Hazardous Substances Direc�ve (RoHS) 2015/863 amending Annex II to Direc�ve 2011/65/EU
Restric�on of the Use of Certain Hazardous Substances in Electrical and Ele
ctronic
G608 (& -E -A) AB090 (& -E -A) G609 (& -E -A) G610 (& -E -A)
FA854 (& -E -A) DA680 (& -E -A) FA855 (& -E -A) FA856 (& -E -A)
GD875 (& -E -A) GH261 (& -E -A) GD876 (& -E -A) GD877 (& -E -A)
IEC 60335-1:2010 +A1:2013 +A2:2016 IEC 60335-2-89:2010 +A1:2012 +A2:2015
Electromagne�c Compa�bility
EN IEC 55014-1:2021 EN IEC 55014-2:2021 EN IEC 61000-3-2: 2019 +A1:2021 EN 61000-3-3: 2013 +A1:2019 +A2:2021
ührten Richtlinie(
n) und Norm(en)
Signature • Unterschri Firma • Firma
et prénom • Vollständiger Name •
Posion • Quali • Posición
Adresse du producteur • Anschri des Herstellers produore • Dirección del fabricante • Morada do
Manager
Avonmouth, Bristol, BS11 8TB
Manager/ Importer
Blarney Business Park, Blarney, Co. Cork
Supplier
15 Badgally Road, Campbelltown NSW 2560
Page 39
UK
+44 (0)845 146 2887
Eire
NL 040 – 2628080
FR 01 60 34 28 80
BE-NL 0800-29129
BE-FR 0800-29229
DE 0800 – 1860806
IT N/A
ES 901-100 133
Page 40
http://www.polar-refrigerator.com/
FA854_FA855_FA856_FA857_DA680_ML_A5_v3_2023/11/02
Loading...