The information relevant to using the product with the transmitter is in blue text.
1. INTRODUCTION TO THE POLAR CYCLING COMPUTER ........................................................................................................7
1.1 PRODUCT ELEMENTS ...............................................................................................................................................7
1.2 USING YOUR CYCLING COMPUTER FOR THE FIRST TIME ...........................................................................................8
1.3 INSTALLING THE BIKE MOUNT, CYCLING COMPUTER AND SPEED SENSOR ..............................................................12
1.3.1 Bike Mount and Cycling Computer..............................................................................................................12
1.4 WEARING YOUR TRANSMITTER ............................................................................................................................... 15
2. EXERCISING
2.1 EXERCISE RECORDING AND HEART RATE MEASURING ...........................................................................................16
2.2 FUNCTIONS DURING EXERCISE ..............................................................................................................................18
2.3 STOPPING THE EXERCISE AND VIEWING SUMMARY FILE .........................................................................................22
3. VIEWING RECORDED INFORMATION - FILE .....................................................................................................................23
4. TOTAL VALUES .................................................................................................................................................................27
5.6 PERSONAL INFORMATION SETTINGS (USER SET) ....................................................................................................45
5.7 CYCLING COMPUTER SOUNDS AND UNITS SETTINGS (GENERAL SET) .....................................................................48
6. EDIT YOUR CYCLING COMPUTER SETTINGS WITH A COMPUTER .....................................................................................49
7. CARE AND MAINTENANCE ................................................................................................................................................50
13. INDEX ..............................................................................................................................................................................62
6 – ENGLISH
1. INTRODUCTION TO THE POLAR CYCLING COMPUTER
1.1 PRODUCT ELEMENTS
The Polar cycling computer package consists of the following parts:
CS100b set does not include a transmitter, but you can buy it as an
accessory product.
Cycling Computer
The cycling computer displays and records
your cycling and exercise data during
exercise. Enter your personal settings into
the cycling computer and analyze exercise
information after workouts.
Polar Bike Mount™
Secure the bike mount to your bike and
attach the cycling computer to it.
Polar Speed Sensor™
A wireless speed sensor measures speed and
distance during cycling.
Polar Coded Transmitter
CS100 set includes a transmitter. The
transmitter sends your heart rate signal to
the cycling computer
on the back of the transmitter detect your
heart rate.
An elastic strap holds the transmitter
around your chest.
The information relevant to using the product
with the transmitter is in blue text.
. The electrode areas
Polar Web Services
.polarpersonaltrainer
www
to support your training goals. Free registration gives you access
to a personalized training program, training diary, useful articles,
and much more. In addition, you can get the latest product tips and
support online at www.polar.com.
The latest version of this user manual can be downloaded at
www.polar.com/support.
.com is a complete web service tailored
ENGLISH– 7
1.2 USING YOUR CYCLING COMPUTER FOR THE FIRST TIME
Enter your settings in the Basic Settings mode (time, date, units, and personal settings).
How to enter Basic Settings
Entering accurate personal information ensures that you receive correct feedback based on your performance
(calorie consumption, OwnZone determination etc).
Activate the cycling computer by pressing the MIDDLE button.
The display fi lls with numbers and letters.
1. Press the MIDDLE button. BASIC SET is displayed.
2. Continue by pressing the MIDDLE button and follow the steps below:
The display reads: Press the RIGHT button to set the fl ashing value Press the MIDDLE button to accept
the value
3. Time Set
Time Mode 24h / 12h
•
• AM / PM (for 12h format)
8 – ENGLISH
RIGHT
• Set 24h or 12h format.
RIGHT
• Set AM or PM.
MIDDLE
MIDDLE
The display reads: Press the RIGHT button to set the fl ashing value Press the MIDDLE button to accept
the value
• Hours
• Minutes
4. Date
Day / Month
•
Set**
RIGHT
• Set the hours.*
RIGHT
• Set the minutes.*
RIGHT
• Set the day (in 24h format) or
MIDDLE
MIDDLE
MIDDLE
the month (in 12h format).*
• Month / Day
RIGHT
MIDDLE
• Set the month (in 24h format) or
the day (in 12h format).*
• Year
RIGHT
MIDDLE
• Set the year.*
Note:
• *The numbers scroll faster if you press and hold the RIGHT button as you adjust the value.
• **The date will be displayed according to the time format selected (24h: day - month - year / 12h: month - day - year).
• After a change of battery or after you reset the cycling computer, you only need to set the time and date in the Basic Settings. You can
skip the rest of the settings by pressing and holding the LEFT button.
ENGLISH– 9
The display reads: Press the RIGHT button to set the fl ashing value Press the MIDDLE button to accept
the value
5. Unit
kg/cm or lb/ft
RIGHT
• Set the units for weight and height:
MIDDLE
kg/cm or lb/ft.
6.
Weight
kg/lb
RIGHT
• Set your weight in kilograms or pounds.
MIDDLE
Note: If you chose the wrong units, you can still
change them by pressing the LEFT button and
returning to step 5.
7. Height
cm/ft
8. Birthday
• Day / Month
RIGHT
• Set your height in cm or ft.
• Set inches (if you chose lb/ft).
RIGHT
• Set the day (in 24h format) or
MIDDLE
MIDDLE
MIDDLE
the month (in 12h format).
• Month / Day
• Year
RIGHT
• Set the month (in 24h format) or
the day (in 12h format).
RIGHT
MIDDLE
MIDDLE
• Set the year.
10 – ENGLISH
The display reads: Press the RIGHT button to set the fl ashing value Press the MIDDLE button to accept
the value
9. Sex
Male / Female
RIGHT
•
Set male or female.
MIDDLE
• Settings done is displayed.
• To change your settings, press the LEFT button until you return to the desired setting.
• To accept the settings, press the MIDDLE button and the cycling computer goes to the Time mode.
The cycling computer goes to the power save mode (blank screen) by pressing the LEFT button or if you do not press any
button in the Time mode for fi ve minutes. You can turn the cycling computer on again by pressing any button.
ENGLISH– 11
1.3 INSTALLING THE BIKE MOUNT, CYCLING COMPUTER AND SPEED SENSOR
1.3.1 BIKE MOUNT AND CYCLING COMPUTER
1. You can install the bike mount and the cycling computer on the left or right side of the handlebar or on the stem with
cable ties.
2.
3.
12 – ENGLISH
2. Place the rubber part on the
handlebar or stem and
insert the bike mount on top
of it.
3. Pass the cable ties over the
bike mount and adjust
them around the handlebar/
stem. Secure the bike mount
fi rmly. Cut off any excess
cable tie ends.
4. Position the cycling computer on to the bike mount. Turn
the cycling computer clockwise until you hear a click.
You can release the cycling computer by pressing it
down and simultaneously turning it counter clockwise.
1.3.2 SPEED SENSOR
To install the speed sensor and spoke magnet, you need cutters and a small screwdriver.
1.
1. Attach the speed sensor
2.
to the opposite side of the
front fork from the mounted
cycling computer.
The speed sensor and the
cycling computer should be
no more than 30-40 cm/
3.
1’-1’3’’ apart.
In case, the cycling computer is attached to the stem or if
you are exercising in surroundings with electromagnetic
interference, the distance should be minimized (minimum
30 cm/1’). The speed sensor and cycling computer should
form approximately a 90° angle.
Should the distance between the cycling computer and the
4.
speed sensor be longer than recommended (for example
on mountain bikes due to the front suspension), the speed
sensor could be attached on the same side of the front
fork as the cycling computer. In this case the maximum
distance is 50 cm/1´6”.
2. Attach the rubber part to the
sensor.
3. Pass the cable ties through
the speed sensor and rubber
part holes.
4. Adjust the sensor to the front
fork so that the POLAR logo
faces outwards. Adjust the
ties loosely. Do not tighten
them fully yet.
ENGLISH– 13
5.
5. Attach the magnet to a spoke
at the same level as the
sensor. The magnet hole
must be facing the speed
max
4 mm /
0’16”
sensor. Fasten the magnet
to the spoke and tighten it
loosely with a screwdriver.
Do not tighten it fully yet.
Fine-tune the positioning of both the magnet and the speed
sensor so that the magnet passes close to the sensor but
does not touch it. Adjust the sensor towards the wheel/
spokes as much as possible. The gap between the sensor
and the magnet should be under 4 mm/0’16’’. The gap is
correct when you can fi t a cable tie just about between the
magnet and the sensor.
Rotate the front tyre so that you can see a speed reading on
the display of your cycling computer. The reading indicates
that the magnet and the speed sensor are positioned
correctly. Once the magnet and the speed sensor are positioned correctly, tighten the screw to the magnet with a
screwdriver. Also tighten the cable ties securely and cut
off any excess cable tie ends.
14 – ENGLISH
Your safety is important to us. While riding your bike,
please keep your eyes on the road to prevent any accidents
and injury. Check that you can turn the handlebar normally
and that the cable wires for brakes or gearing do not catch
on the bike mount or the speed sensor. Check also that the
bike mount or speed sensor does not hamper pedaling or
the use of brakes or gearing.
Before you start cycling, you should set the wheel size of
your bicycle into the cycling computer. For further information
see pages 39-42.
1.4 WEARING YOUR TRANSMITTER
Coded heart rate transmission reduces interference from other heart rate monitors that are close by. To make sure that the
code search is successful and to ensure trouble-free heart rate monitoring, keep the cycling computer within 1 meter/3 feet of your transmitter. Check that you are not near other people with heart rate monitors or any source of electromagnetic
disturbance. For further information on interference, see Precautions on page 53.
To measure your heart rate, you need to wear the transmitter.
1.
1. Attach one end of the
3.
transmitter to the elastic
strap.
3. Lift the transmitter off your
chest and moisten the two
grooved electrode areas on
the back.
2.
2. Adjust the strap length to fi t
4.
snugly and comfortably.
Secure the strap around your
chest, just below the chest
muscles, and buckle the
strap to the transmitter.
See the following chapter for how to start measuring your
heart rate.
See detailed washing instructions in Care and Maintenance chapter.
4. Check that the wet electrode
areas are fi rmly against your
skin and that the Polar logo
is in a central, upright
position.
ENGLISH– 15
2. EXERCISING
2.1 EXERCISE RECORDING AND HEART RATE MEASURING
You can record one Exercise File. There are two ways to start exercise recording. If you turn on the AutoStart function,
the cycling computer automatically starts and stops exercise recording when you start and stop cycling. If the AutoStart
function is off, you can start exercise recording by pressing the MIDDLE button. For further information on AutoStart and
how to set the function on/off, see pages 39-40.
Starting exercise without the transmitter:
1. Attach the bike mount and speed sensor on your bicycle
according to the instructions on pages 12-14.
2. Set your cycling computer on to the mounted bike mount.
3. Activate your blank cycling computer by pressing the MIDDLE
button. Before you start cycling, wait for 15 seconds until the
framed heart symbol
display. Now the computer is ready to record your exercise.
4. If you have turned AutoStart on, your speed appears on the
display when you start cycling. If you have turned AutoStart off,
you can start exercise recording by pressing the MIDDLE button
and your speed appears on the display. Your exercise time also
starts running.
5. If you have turned AutoStart on, the cycling computer
automatically stops exercise recording when you stop cycling.
If AutoStart is off, you can stop the exercise by pressing the LEFT button twice. For further information on Stopping the
exercise, see page 22.
16 – ENGLISH
disappears from the Time mode
Starting exercise with the transmitter:
ear the transmitter as described in the section “Wearing your
W
1.
Transmitter” on page 15. Attach the bike mount and speed sensor
on your bicycle according to the instructions on pages 12-14.
2. Activate your blank cycling computer by pressing the MIDDLE
button and start from the Time mode. The cycling computer will
automatically read your heart rate. Wait until the computer
detects your heart rate and the framed, fl ashing heart symbol
appears on the display in 15 seconds.* Exercise time is not
recorded yet.
3. Set your cycling computer on to the mounted bike mount. If you
have turned AutoStart on, your heart rate value and speed
appear on the display when you start cycling. If you have turned
AutoStart off, you can start exercise recording by pressing the
MIDDLE button and your heart rate value and speed appear on
the display. Your exercise time also starts running.
4. If you have turned AutoStart on, the cycling computer
automatically stops exercise recording when you stop cycling.
If AutoStart is off, you can stop the exercise by pressing the LEFT button twice. For further information on Stopping the
exercise, see page 22.
• If your heart rate is not displayed and 00 appears on the display, the heart rate detection has stopped. Bring the cycling
computer near the Polar logo on the transmitter to restart the heart rate detection. No button press is needed.
• If OwnZone® is selected, the OwnZone determination procedure begins when exercise recording starts. For further
information, see the section OwnZone on page 36.
• To skip the OwnZone determination and use the previously determined OwnZone, press the MIDDLE button when OwnZone
symbol appears on the display. If you have not determined your OwnZone before, your age-based heart rate
limits will be used.
Note: * A frame around the heart rate symbol indicates a coded heart rate transmission.
• If the cycling computer does not display your heart rate, make sure that the transmitter electrodes are moist and that the strap is
snug enough.
ENGLISH– 17
2.2 FUNCTIONS DURING EXERCISE
Note: Your exercise information is saved only if the stopwatch, i.e. your exercise duration, has been running for more than one minute or at
least one lap has been stored.
Changing the display information: Press the RIGHT button to view the following options during exercise:
1.Ridden distance alternates with trip distance when you have taken at least one lap time.
Speed and heart rate are also displayed graphically. The more bars are displayed, the higher
your heart rate or speed and vice versa. One speed bar represents 5 km/h or 3 mph, and when all ten bars are displayed your
speed is 50 km/h or 30 mph or higher.
2.
Average speed rise
indicator.
Speed
Heart rate
18 – ENGLISH
Trip distance is reset to zero each time you take a lap time by pressing the MIDDLE button.
Riding speed (km/h or m/h)
Heart rate. If there is no heart rate reading or you have not set your user information,
the speed is displayed instead.
or drop
Note: You can also press and hold the RIGHT button to set the computer
to browse the views automatically. Scrolling can be turned off by
pressing and holding the RIGHT button.
3.The kilocalories you have burned so far. The cumulation of kilocalories starts as your heart rate
is displayed. If there is no heart rate reading or you have not set your user information, the speed
is displayed instead of calorie information.
Stopwatch, i.e., exercise duration.
Heart rate
4.
The estimated time of arrival, or if the riding distance function is off, the speed is displayed
instead. If you set the distance you are going to ride, the cycling computer estimates your arrival
time to the destination according to your riding speed. For further information, see page 31.
T
ime of day
Heart rate
5.
Heart rate limits:
On the left, you can see your lower heart rate limit and on the right your
upper heart rate limit. The heart rate symbol moves left or right according to your heart rate.
If the heart symbol is not visible, it means your heart rate is either below the fl
ashing lower
heart rate limit or above the fl ashing upper heart rate limit. In this case an alarm goes on,
provided the sounds are turned on. If there is no heart rate reading, the limits are not displayed.
For further information, see page 34.
Time you have exercised in target zone, i.e., within the heart rate limits.
Heart rate
ENGLISH– 19
Target Zone Alarm: With the Target Zone Alarm you can make sure you exercise at the right intensity. When the target zone
heart rate limits are activated, the cycling computer sounds an alarm if you are above or below your heart rate limits. You
can set the limits for your target zone in the Settings/Limits SET menu. For further information, see page 34.
If you are out of your target zone, the heart rate value starts fl ashing and the cycling computer beeps with each heartbeat.
The symbol in the upper right corner of the display
indicates that the Target Zone Alarm sound is activated. Note that
the button sounds can also be set on/off in the Settings mode. To turning the sounds on or off, see page 48.
Note: When heart rate limits are not activated, no Target Zone Alarm in the exercise recording will sound, nor will target zone information be
placed in the Summary File or File.
Storing Lap and Split Time: Press the MIDDLE button to store lap and split time.
Lap time indicates elapsed time for one lap. Split time is elapsed time from the beginning of the exercise until storing a lap
time (for example from the beginning of the exercise until the 4th lap was stored).
Lap time
Number of the lap
Split time
Average heart rate calculated
from the beginning of the lap.
Note:
• If you have activated the AutoLap function in the Settings mode, your cycling computer automatically records laps when you reach the
set distance, e.g., every kilometer or mile. For further information, see page 31.
• You can store up to 50 lap times. When the lap memory is full, LapTime FULL text will be displayed. You can take lap times during your
exercise, but they are no longer recorded.
20 – ENGLISH
Timers: The timers of your cycling computer work during your exercise recording. The cycling computer beeps and shows
when the timer time matches. If only timer 1 is on, the same timer beeps always after the set time has elapsed during your
exercise. If timer 2 is also on, the timers alternate during your exercise. For further information, see page 33.
Pausing Exercise:
1. Press the LEFT button. Exercise recording, stopwatch, and other calculations are paused.
2. To continue, press the MIDDLE button.
Exercising in the dark: If you activate the backlight by pressing and holding the MIDDLE button during an exercise
recording, the backlight will reactivate automatically during the same exercise every time you press any button.
Note: If the maximum fi le recording time (99 hours 59 min 59 s) is exceeded, the cycling computer beeps, pauses recording and displays
HALT. Stop recording by pressing the LEFT button.
ENGLISH– 21
2.3 STOPPING THE EXERCISE AND VIEWING SUMMARY FILE
1. Press the LEFT button to pause the exercise recording. Paused is displayed.
2. Press the LEFT button. Summary FILE is displayed and the following information starts automatically scrolling:
Recorded Exercise File Information
Duration of recorded exercise.
Average heart rate.
Limits
In Zone
Kcal
AvgSpeed
Avg Cad.
Distance
RideTime
*Optional Polar Cadence Sensor required.
22 – ENGLISH
Heart rate limits used during your exercise (if limits are set).
Time spent in target heart rate zone.
Kilocalories burnt during exercise.
verage speed.
A
Average cadence.*
Ridden distance.
ime used for cycling.
T
E.g., if you stop cycling but do not stop the exercise recording the cycled time counting will automatically stop,
but the exercised time will continue to elapse.
If the AutoStart function is activated, the exercise and cycled time is the same, because the cycling computer
automatically starts and stops the recording as you start and stop cycling.
3. VIEWING RECORDED INFORMATION - FILE
The Exercise File allows you to review cycling and exercise information collected while recording
an exercise session. The cycling computer starts recording information in a File as soon as
you start recording by pressing the MIDDLE button or using AutoStart function. Your exercise
information is saved only if the stopwatch has been on for more than one minute or at least one
lap has been stored.
Viewing Exercise File
Press MIDDLE
• Date/Time
Press RIGHT
• Exe.Time/Avg HR/Max HR
Press RIGHT
• Limits
Press RIGHT
• In/Above/Below Zone
Press RIGHT
• Kcal
Press RIGHT
• Distance
Press RIGHT
• Avg/MaxSpeed
Press RIGHT
• Avg/Max.Cad*
Press RIGHT
• RideTime
Press RIGHT
• Laps
1. In the Time mode, press the RIGHT button. FILE is displayed.
2. Press the MIDDLE button. Date and Time alternate on the display.
Recorded Exercise File Information
*Optional Polar Cadence Sensor required.
The date and time when the exercise started alternate
on the display.
ENGLISH– 23
3. Press the RIGHT button to browse through the recorded information.
Recorded Exercise File Information
Exe.Time
Avg HR / Max HR
Limits
In/Above/Below
Zone
Kcal
Distance
vgSpeed
A
Max
Note:
• The alternating information switches automatically on the display. For quick scrolling, press the MIDDLE button.
• Press and hold the MIDDLE button to turn the backlight on in the File mode.
24 – ENGLISH
Duration of recorded exercise.
The average heart rate and maximum heart rate alternate in heartbeats per minute (bpm).
Note: If you set heart rate limits in percentages of your maximum heart rate, these values are
displayed also as percentages of your maximum heart rate (%).
The heart rate limits (in bpm or %) used during the exercise (if limits are set).
The exercise time that you have spent within (In Zone), above and below your target zone
limits (if limits are set) alternate on the display
Expended kilocalories during the exercise.
Ridden distance.
verage and maximum speed.
A
.
Recorded Exercise File Information
Avg Cad.
Max
RideTime
LAPS
Average and maximum cadence.*
Time used for cycling.
Number of laps while exercising.
Note:
Lap information is displayed if you have stored at least one lap during
your exercise.
4. To view the best lap, press the MIDDLE button.
The best lap information is displayed:
The fastest lap time.
The number of the best lap.
5. Browse the laps with the RIGHT button. By pressing the MIDDLE button
you can browse the following lap information:
Split time.
Lap time.
The maximum heart rate and the average heart rate during the lap alternate
on the display
Note:
.
The last lap is automatically recorded when the exercise has been
stopped by pressing the LEFT button, but it is never the best lap.
*Optional Polar Cadence Sensor required.
ENGLISH– 25
Recorded Exercise File Information
Speed
The speed when you recorded the lap.
Average speed during the lap.
Cadence*
The cadence when you recorded the lap.
A
verage cadence during the lap.
Distance
The Lap and
Split distances alternate on the display.
• To return to the Time mode, press and hold the LEFT button.
*Optional Polar Cadence Sensor required.
26 – ENGLISH
4. TOTAL VALUES
Total values include cumulative and maximum values of information recorded during your
training sessions. Use the Total values fi le as a daily and weekly counter of your training values.
The values are updated automatically, when exercise recording is stopped.
In addition to the daily and weekly values, you can view the seasonal cumulative and maximum
values. These values are collected until you reset them, which means that you can use this
function for example as a monthly counter of your training values. For further information on
how to reset the values, see page 30.
Press MIDDLE
• Today’s TOTALS
Press RIGHT
• ThisWeek TOTALS
Press RIGHT
• Season’s TOTALS
Viewing the Total Values
1. In the Time mode, press the RIGHT button until TOTALS is displayed.
2. Press the MIDDLE button. Today’s TOTALS is displayed.
3. Select the time scale (Today’s, ThisWeek or Season’s) you want to view with the RIGHT button.
4. Press the MIDDLE button. Tot.Time and the total time are displayed.
5. If you choose Today’s TOTALS or ThisWeek TOTALS you can use the RIGHT button to browse through following information:
Tot.Time, Tot.Kcal, Distance1, Distance2*, MaxSpeed, Max.Cad** and RideTime.
*You need to do bike settings to see values for bike 1 and bike 2.
**Optional Polar Cadence Sensor required.
• Today’s TOTALS The cycling computer automatically resets the total values to zero at midnight (00:00).
• ThisWeek TOTALSThe cycling computer automatically resets the total values to zero
between Sunday and Monday at midnight (00:00).
• Season’s TOTALSReset the total values to zero by yourself whenever you want.
ENGLISH– 27
6. If you choose Season’s TOTALS you can use the RIGHT button to browse through following information:
Total Values
The date when cumulation started.
Total cumulative exercise duration.
The date when cumulation started.
Total cumulative burned kilocalories.
The date when cumulation started.
Odometer alternates with the date when cumulation started and the
cumulation for both bike 1 and bike 2.
The odometer measures the cumulative ridden distance and it can
Note:
only be reset by using the UpLink. For further information, see page 49.
28 – ENGLISH
Total Values
*Optional Polar Cadence Sensor required.
The date when cumulation started.
The ridden distance cumulation for bike 1 and bike 2 (Distance1 is updated when
bike 1 is used and Distance2 is updated when bike 2 is used).
The date when updated.
Maximum speed of the season.
The date when updated.
Maximum cadence of the season.*
ENGLISH– 29
Total Values
The date when cumulation started.
Total cumulative ridden duration.
• To return to the Time mode, press and hold the LEFT button.
Resetting Season’s TOTALS or Returning the Previous Maximum Speed or Cadence* Value
Use Total values as a seasonal (or daily/weekly) counter of your exercise values by resetting them once a season. Instead of
resetting, you can return the previous maximum speed and cadence* value. Once reset or returned, a value cannot be retrieved.
Start with any display in the previous table (Tot.Time, Tot.Kcal, Distance1/2, MaxSpeed, Max.Cad*, RideTime).
1. Press the MIDDLE button to start resetting the desired value. Reset? is displayed. In MaxSpeed and Max.Cad* displays
you can continue by pressing the RIGHT button to return the previous value. Select Return Old using the MIDDLE button.
2. Press the MIDDLE button. Are You Sure is displayed.
3. If sure, press the MIDDLE button.
Alternatively, to cancel the reset, press the LEFT button.
• To return to the Time mode, press and hold the LEFT button.
Note: The odometer can be reset only by using the UpLink. For further information, see page 49.
*Optional Polar Cadence Sensor required.
30 – ENGLISH
5. SETTINGS
Press MIDDLE
• Cycling SET
Press RIGHT
• Timer SET
Press RIGHT
• Limits SET
Press RIGHT
• Bike SET
Press RIGHT
• Watch SET
Press RIGHT
• User SET
Press RIGHT
• General SET
You can view or change the settings in the Settings menu.
Tip: Settings can also be confi gured using the Polar UpLink Tool™. They can then be transferred to your
cycling computer from your PC. For further information, see page 49.
To set values:
• Adjust or select a value with the RIGHT button.
• Accept your selection and proceed in the menu with the MIDDLE button.
• Cancel your selection or return to the previous mode or menu by pressing the LEFT button.
5.1 RIDING DISTANCE FOR ESTIMATED TIME OF ARRIVAL FUNCTION AND
AUTOMATIC LAP RECORDING SETTINGS (CYCLING SET)
In the cycling settings you can make two different settings:
• RideDist: Setting riding distance.
Set the distance you are going to ride and the cycling computer will estimate your arrival
time to the destination according to your riding speed.
• AutoLap: Automatic lap recording.
Set the distance for the automatic lap and the cycling computer will record the lap
information every time you reach this distance. For example, if you set 1 km/m, the cycling
computer will record lap information every kilometer or mile.
ENGLISH– 31
Both functions work during your exercise recording. For further information, see pages 18-20.
1. In the Time mode, press the RIGHT button until SETTINGS is displayed.
2. Press the MIDDLE button. Cycling SET is displayed.
3. Continue by pressing the MIDDLE button and follow the steps below:
The display reads: Press the RIGHT button to set the fl ashing value Press the MIDDLE button to accept
the value
4. RideDistOn / OFF
5. RideDistOn
6. AutoLapOn / OFF
7. AutoLapOn
RIGHT
T
urn the riding distance function on or off.
•
RIGHT
• Adjust the kilometers or miles.
RIGHT
• Turn the automatic lap recording function on
or off.
RIGHT
• Adjust the kilometers or miles.
MIDDLE
(Skip step 5, if you turned the function off)
MIDDLE
MIDDLE
(Skip step 7, if you turned the function off)
MIDDLE
• To return to the Time mode, press and hold the LEFT button.
32 – ENGLISH
5.2 TIMER SETTINGS (TIMER SET)
Your cycling computer is equipped with two alternating timers. The timers work during your exercise recording.
Tip: Use the timers for example as a reminder to drink at certain intervals or as a training tool in interval training, so that you know when
to switch from a harder to a lighter period and vice versa.
1. In the Time mode, press the RIGHT button until SETTINGS is displayed.
2. Press the MIDDLE button. Cycling SET is displayed.
3. Press the RIGHT button. Timer SET is displayed.
4. Continue by pressing the MIDDLE button and follow the steps below:
The display reads: Press the RIGHT button to set the fl ashing value Press the MIDDLE button to accept
the value
5. Timer 1On / OFF
6. T
imer 1
On
• To set timer 2, repeat steps 5 and 6.
• To return to the Time mode, press and hold the LEFT button.
RIGHT
• Turn the Timer on or off.
RIGHT
• Adjust the minutes (0-99 minutes).
RIGHT
• Adjust the seconds (0-59 seconds).
MIDDLE
(Skip step 6, if you turned the function off)
MIDDLE
MIDDLE
ENGLISH– 33
5.3 HEART RATE LIMITS SETTINGS (LIMITS SET)
In the heart rate limits settings (Limits SET) you can choose the heart rate limit type:
• Manual Limits:You can create a target heart rate zone by setting the upper and the lower heart rate limits manually.
• OwnZone:The cycling computer is able to determine your individual aerobic (cadiovascular) exercise heart rate
zone automatically. This is called OwnZone (OZ). OwnZone ensures that you exercise within safe
limits. For further information, see page 36.
• Limits Off:You can also deactivate target zone limits, when there are no target heart rate limits during the
exercise recording, and no target heart rate zone values (In Zone) are calculated in the summary File
or File.
Use OwnZone or the target heart rate zone to maintain a particular level of intensity, depending on your objectives.
1. In the Time mode, press the RIGHT button until SETTINGS is displayed.
2. Press the MIDDLE button. Cycling SET is displayed.
3. Press the RIGHT button until Limits SET is displayed.
34 – ENGLISH
4. Continue by pressing the MIDDLE button and follow the steps below:
The display reads: Press the RIGHT button to set the fl ashing value Press the MIDDLE button to accept
the value
5. TYPEManual / OwnZone / Off
RIGHT
• Select Manual or OwnZone (automatic defi nition
MIDDLE
(Skip steps 6-8, if you turned the function off)
of your personal heart rate zone) or Off.
6. HR / HR%SET
7. HighLimit
8. LowLimit
RIGHT
• Select heart rate displayed as beats per minute
(bpm) or as % of your maximum heart rate
).
(% HR
max
RIGHT
• Adjust the upper heart rate limit.
RIGHT
• Adjust the lower heart rate limit.
MIDDLE
(Skip steps 7-8, if you chose OwnZone)
MIDDLE
MIDDLE
• To return to the Time mode, press and hold the LEFT button.
ENGLISH– 35
5.3.1 OWNZONE
The Polar cycling computer is able to determine your individual aerobic (cardiovascular) exercise heart rate zone
automatically. This is called OwnZone (OZ).
OwnZone is based on measuring changes in heart rate variability during your warm up. Heart rate variability refl ects
changes in your physiology. For most adults OwnZone corresponds to 65-85 % of maximum heart rate. OwnZone can be
determined in 1-5 minutes during a warm-up period by cycling, walking or jogging. OwnZone may be easier to fi nd during
indoor cycling than outdoor cycling because the speed is easier to control. The main idea is that you start exercising slowly
at a light intensity, i.e., heart rate lower than 100 bpm/50 % HR
. You then gradually increase the intensity of your
max
exercise to raise your heart rate as smoothly as possible. Using OwnZone makes exercise easier and more enjoyable.
OwnZone has been developed for healthy people. Some health conditions may cause heart rate variability based OwnZone
determination to fail, for example high blood pressure, some cardiac arrhythmias, and some medications.
36 – ENGLISH
Determining Your OwnZone Heart Rate Limits
Before you start to determine your OwnZone, make sure of the following:
• You have entered your user settings correctly. The cycling computer will ask for missing information (for example date of
birth) before accepting limit settings.
• You have activated the OwnZone limits. With the OwnZone function on, the cycling computer will automatically determine
your OwnZone every time you start recording an exercise session.
You should redefi ne your OwnZone:
• when changing your exercise environment or exercise mode;
• if you are returning to exercise after a more than one week off;
• if you feel unusual about the physical state of your body when starting to exercise. For example you are stressed, not
recovered from the previous training or not feeling well;
• after changing your settings.
1. Start from the Time mode and press the MIDDLE button. The OwnZone symbol
appears on the display. If you
want to skip OwnZone determination and use the previously determined OwnZone, press the MIDDLE button.
2. OwnZone determination starts. Determination of your OwnZone happens in fi ve stages.
Cycle or walk at a slow pace for 1 min. Keep your heart rate below 100 bpm/ 50 % HR
during this fi rst
max
stage. After each stage you will hear a beep (if the sound settings are on) and the display automatically
illuminates (if you have switched the backlight on once before), indicating the end of the stage.
Cycle or walk at a normal pace for 1 min. Slowly increase your heart rate by 10-20 bpm/ 5 % HR
Cycle or walk at a brisk pace for 1 min. Slowly increase your heart rate by 10-20 bpm/ 5 % HR
max
max
.
.
Cycle at a brisk pace or jog at a slow pace for 1 min. Slowly increase your heart rate by 10-20 bpm/ 5 % HR
Cycle or jog at a brisk pace or run for 1 min.
ENGLISH– 37
max
.
3. At some point during the stages, you hear two beeps. Your OwnZone has been determined. If the determination was
successful, OwnZone and Updated alternate with the heart rate limits on the display. The limits are displayed as beats
per minute (bpm) or as a percentage of your maximum heart rate (%HR
) depending on your settings.
max
4. If the determination was not successful, your previously determined OwnZone limits will be used and OwnZone appears
with the limits on the display. If you are determining your OwnZone for the fi rst time, then the limits based on your age
will be used.
You can now continue with your exercise. Try to stay within the given heart rate zone to maximize exercise benefi ts.
For further information on OwnZone, see www.polar.com.
38 – ENGLISH
5.4 BICYCLE SETTINGS (BIKE SET)
You can set two bike preferences for the cycling computer. Prepare the settings for both bikes; when you start exercise
recording, just select bike 1 or 2. For both bikes you can prepare the following settings:
• AutoStart on/off The AutoStart function starts or stops automatically the exercise recording when you start or
stop cycling.
• Cadence on/offA wireless cadence sensor measures the speed at which you turn the pedals of your bicycle.
An optional Polar Cadence sensor is required.
• WheelWheel size settings are a prerequisite for cycling information. For further information, see the
following page.
1. In the Time mode, press the RIGHT button until SETTINGS is displayed.
2. Press the MIDDLE button. Cycling SET is displayed.
3. Press the RIGHT button until Bike SET is displayed.
ENGLISH– 39
4. Continue by pressing the MIDDLE button and follow the steps below:
The display reads: Press the RIGHT button to set the fl ashing value Press the MIDDLE button to accept
the value
5. Bike 1 / 2
6. AutoStart
On / OFF
7. Cadence*
On / OFF
8. Wheel
RIGHT
• Select which bike settings you want to set:
bike 1 or 2.
RIGHT
• Turn AutoStart function on or off.
RIGHT
• Turn cadence function on or off.
RIGHT
• Adjust the wheel size (mm) of your bicycle.
MIDDLE
MIDDLE
MIDDLE
MIDDLE
• To return to the Time mode, press and hold the LEFT button.
Note:
• The wheel size is always indicated in millimeters, as it is more accurate.
• The speed and distance measuring functions are always on.
*Optional Polar Cadence Sensor required.
40 – ENGLISH
You have the following alternatives for fi nding out the wheel size of your bike:*
METHOD 1.
Look at the wheel of your bike and fi nd the wheel diameter printed on it.
On the chart below, fi nd your wheel diameter in inches or in ETRTO reading and match it to the wheel size in millimeters on
the right.
25-559 26 x 1.0 1884
23-571 650 x 23C 1909
35-559 26 x 1.50 1947
37-622 700 x 35C 1958
47-559 26 x 1.95 2022
20-622 700 x 20C 2051
52-559 26 x 2.0 2054
23-622 700 x 23C 2070
25-622 700 x 25C 2080
28-622 700 x 28 2101
32-622 700 x 32C 2126
42-622 700 x 40C 2189
47-622 700 x 47C 2220
Note: *Wheel sizes on the above chart are advisory as wheel size depends on the wheel type and air pressure.
ENGLISH– 41
METHOD 2.
Mark the tread of the front tire with a line and roll the tire perpendicular to the ground. You can also use the valve as a
mark. Mark a line on the ground. Move your bike on a fl at surface straight ahead for one complete wheel rotation. Check that
the tire is perpendicular to the ground. Draw another line on the ground exactly where the mark on the front tire touches the
ground.
-4 mm
mm
mm
42 – ENGLISH
Measure the distance between the two lines on the ground.
Subtract 4 mm to account for your weight on the bike to get your wheel circumference.
This is the value you must set on the cycling computer.
5.5 WATCH SETTINGS (WATCH SET)
In the Watch SET menu, you can change the time of day and date settings.
1. In the Time mode, press the RIGHT button until SETTINGS is displayed.
2. Press the MIDDLE button. Cycling SET is displayed.
3. Press the RIGHT button until Watch SET is displayed.
4. Continue by pressing the MIDDLE button and follow the steps below:
The display reads: Press the RIGHT button to set the fl ashing value Press the MIDDLE button to accept
the value
5. Time
ime Mode 24h/12h
• T
• AM / PM
(if you use 12h format)
RIGHT
• Set 24h or 12h time mode.
RIGHT
• Set AM or PM.
RIGHT
• Set the hours.
RIGHT
• Set the minutes.
MIDDLE
MIDDLE
MIDDLE
MIDDLE
ENGLISH– 43
The display reads: Press the RIGHT button to set the fl ashing value Press the MIDDLE button to accept
the value
6. Date*
• Day / Month
• Month / Day
• Year
RIGHT
Set the day (in 24h mode) or
•
the month (in 12h mode).
RIGHT
• Set the month (in 24h mode) or
the day (in 12h mode).
RIGHT
• Set the year.
MIDDLE
MIDDLE
MIDDLE
• To return to the Time mode, press and hold the LEFT button.
Note: *The order in which you set date settings depends on which time mode you have chosen (24h: day - month - year /
12h: month - day - year).
44 – ENGLISH
5.6 PERSONAL INFORMATION SETTINGS (USER SET)
Entering your personal information ensures that your calorie counter operates with the highest possible degree of accuracy.
1. In the Time mode, press the RIGHT button until SETTINGS is displayed.
2. Press the MIDDLE button. Cycling SET is displayed.
3. Press the RIGHT button until User SET is displayed.
4. Continue by pressing the MIDDLE button and follow the steps below:
The display reads: Press the RIGHT button to set the fl ashing value Press the MIDDLE button to accept
the value
5. Weight
kg/lb
6. Height
cm/ft
RIGHT
Set your weight in kilograms or pounds.
•
RIGHT
Set your height in cm or ft.
•
• Set inches (if you chose lb/ft).
MIDDLE
MIDDLE
MIDDLE
ENGLISH– 45
The display reads: Press the RIGHT button to set the fl ashing value Press the MIDDLE button to accept
the value
7. Birthday
• Day / Month
• Month / Day
RIGHT
• Set the day (in 24 h mode) or
the month (in 12 h mode).
RIGHT
• Set the month (in 24h mode) or
MIDDLE
MIDDLE
the day (in 12h mode).
ear
• Y
HR Max
8.
RIGHT
• Set the year.
RIGHT
• Adjust HR
measured current maximum heart rate
, if you know your laboratory
max
MIDDLE
MIDDLE
value. Your age-predicted maximum heart rate
value (220-age) is displayed as a default
setting when you set this value for the fi rst
time.
9. HR Sit
RIGHT
MIDDLE
• Adjust your heart rate value in a sitting
position (see the instructions on the next page).
10. Sex
• Male / Female
RIGHT
• Set male or female.
MIDDLE
• To return to the Time mode, press and hold the LEFT button.
46 – ENGLISH
Maximum heart rate value (HR
HR
is used to estimate energy expenditure. HR
max
physical exertion. HR
individual HR
is also useful when determining exercise intensity. The most accurate method for determining your
max
is to perform a maximal exercise stress test in a laboratory.
max
max
)
is the highest number of heartbeats per minute during maximum
max
Heart rate value in a sitting position (HR
HR
is used to estimate energy expenditure. HR
sit
activity (while sitting). To determine your HR
)
sit
should be your typical heart rate when you are not doing any physical
sit
easily, wear your transmitter, hold your cycling computer in your hand, sit
sit
down and do not engage in any physical activity. After two or three minutes, press the MIDDLE button in the Time mode to
view your heart rate. This is your HR
To calculate your HR
more precisely, repeat the procedure several times and calculate your average.
sit
.
sit
ENGLISH– 47
5.7 CYCLING COMPUTER SOUNDS AND UNITS SETTINGS (GENERAL SET)
You can view and change the following settings in the General SET:
• SoundsActivity sounds for the cycling computer on or off .
• KeySound Button sounds for the cycling computer on or off.
• UnitsThe Unit settings affect the personal information and watch settings.
1. In the Time mode, press the RIGHT button until SETTINGS is displayed.
2. Press the MIDDLE button. Cycling SET is displayed.
3. Press the RIGHT button until General SET is displayed.
4. Continue by pressing the MIDDLE button and follow the steps below:
The display reads: Press the RIGHT button to set the fl ashing value Press the MIDDLE button to accept
the value
5. Sound On / OFF
6. KeySound On / OFF
kg/cm or lb/ft
7.
Unit
• To return to the Time mode, press and hold the LEFT button.
48 – ENGLISH
RIGHT
• Turn activity sounds on or off.
RIGHT
• Turn button sounds on or off.
RIGHT
• Select kg/cm or lb/ft units.
MIDDLE
MIDDLE
MIDDLE
6. EDIT YOUR CYCLING COMPUTER SETTINGS WITH A COMPUTER
The Polar cycling computer offers you the option of editing your cycling computer settings with the Polar UpLink Tool and
your computer. You can also personalize the display of your cycling computer by downloading logos. For this you need the
Polar UpLink Tool.
You can download the Polar UpLink Tool at www.polar.com or www.polarpersonaltrainer.com. In order to be able to use the
Polar UpLink Tool, you need a computer with a sound card and dynamic loudspeakers or headphones. For further information
on system requirements, see the chapter Technical Specifi cations. See www.polar.com or www.polarpersonaltrainer.com for
further instructions.
ENGLISH– 49
7. CARE AND MAINTENANCE
Caring for Your Product
Like any electronic device, your Polar cycling computer
should be treated with care. The suggestions below will
help you to fulfi ll guarantee obligations and enjoy this
product for many years to come.
Wash the transmitter regularly after use with a mild soap
and water solution and a soft brush if needed. Do not dry
the transmitter with anything other than a soft towel.
Mishandling may damage the electrodes. Do not bend or
stretch the transmitter
Keep your cycling computer
in a cool and dry place. Do not keep them in a damp
environment, in non-breathable material (a plastic bag or
a sports bag) nor with conductive material (a wet towel).
The cycling computer,
resistant, and can be used in rainy weather. To maintain
the water resistance, do not wash the cycling computer
or the sensors with a pressure washer or sink them under
water. Do not expose to direct sunlight for extended periods
such as by leaving it in a car or mounted on the bike
mount.
50 – ENGLISH
. This may damage the electrodes.
, transmitter and sensors
transmitter and sensors are water
Keep your cycling computer clean. Clean the cycling
computer and sensors with a mild soap and water solution
and rinse them with clean water. Do not immerse them
in water. Dry them carefully with a soft towel. Never use
alcohol or any abrasive material such as steel wool or
cleaning chemicals.
Avoid hard hits to the cycling computer and speed sensor,
as these may damage the sensor units.
Service
During the two-year guarantee/warranty period we
recommend that you have service done by an authorized
Polar Service Center only. The warranty does not cover
damage or consequential damage caused by service not
authorized by Polar Electro.
For contact information and all Polar Service Center
addresses, visit www.polar.com/support and country
specifi c websites.
Register your Polar product at http://register.polar.fi / to
ensure we can keep improving our products and services to
better meet your needs.
Note: The username for your Polar Account is always your email
address. The same username and password are valid for Polar
product registration, polarpersonaltrainer.com, Polar discussion
forum and Newsletter registration.
Cycling Computer Battery
The CS100 cycling computer has a user changeable
battery. To change the battery yourself, please follow the
instructions carefully.
Note: In order to ensure the maximum lifespan of the battery
cover, open it only when you need to change the battery.
• The low battery indicator and LowBatt. is displayed when
10-15% of the cycling computer battery capacity is left and
the battery should be replaced. The backlight and cycling
computer sounds are automatically deactivated when is
displayed.
• Excessive use of the backlight drains the cycling computer’s
battery more rapidly.
• In cold conditions the low battery indicator may appear,
but the indicator disappears when you return to warmer
temperature.
Change Batteries Yourself
Transmitter and Speed Sensor Battery
Contact your authorized Polar Service Center for a replacement transmitter or speed sensor.
When changing the battery, make sure the sealing ring is
not damaged, in which case you should replace it with a
new one. You can purchase the sealing ring/battery kits at
well-equipped Polar retailers and authorized Polar Services.
ENGLISH– 51
In the USA and Canada, the additional sealing rings are
available at authorized Polar Service Centers. In the USA
the sealing ring/battery kits are also available at www.
shoppolar.com.
Keep the batteries away from children. If swallowed,
contact a doctor immediately.
Batteries should be properly disposed of according to local
regulations.
When handling a new, fully charged battery, avoid clasplike contact, i.e. simultaneous from both sides, with metal
or electrically conducting tools, like tweezers. This may
short-circuit the battery causing it to discharge more
rapidly. Typically, short circuiting does not damage the
battery, but it may decrease the capacity and lifetime of
the battery.
Danger of explosion if the battery is replaced with wrong
type.
52 – ENGLISH
Changing Cycling Computer Battery
1.
2.
replace with a new one. Be careful not to damage the
threads of the back cover.
3. Place the negative (-) side of the battery against the
cycling computer and the positive (+) side against the
cover.
1. Using a coin that sits tight into
the back cover groove, open
the battery cover by pressing
slightly and unscrewing
counter clockwise.
2. Remove the battery cover.
The battery is attached to
the cover, which should be
carefully lifted with a suitable
sized small rigid stick or
bar, such as a toothpick. A
non-metal tool is preferable.
Remove the battery and
4. The sealing ring of the battery cover is also attached to
the cover. Only replace the sealing ring if it is damaged.
Before closing the battery cover, make sure that the
cover’s sealing ring is undamaged and it is placed
correctly in its groove.
5. Put the battery cover in its place and close it by screwing
the cover clockwise with a coin. Make sure that the cover
is closed properly!
Note: After a battery change re-enter time and date settings in
the Basic Settings. For further information, see page 8.
ENGLISH– 53
8. PRECAUTIONS
The Polar cycling computer shows your performance
indicators. It indicates the level of physiological strain and
intensity during your training session. It also measures
speed and distance when cycling with a Polar speed sensor.
No other use is intended or implied.
Electromagnetic Interference
Disturbances may occur near high voltage power lines,
traffi c lights, overhead lines of electric railways, electric
bus lines or trams, televisions, car motors, bike computers,
some motor driven exercise equipment, cellular phones, or
when you walk through electric security gates.
Minimizing Risks When Training
Training may include some risk. Before beginning a regular
training program, answer the following questions concerning your health status. If you answer yes to any of these
questions, consult a physician before starting any training
program.
• Have you been physically inactive for the past fi ve years?
• Do you have high blood pressure or high blood cholesterol?
54 – ENGLISH
• Do you have symptoms of any disease?
• Are you taking any blood pressure or heart medication?
• Do you have a history of breathing problems?
• Are you recovering from a serious illness or medical
treatment?
• Do you use a pacemaker or another implanted electronic
device?
• Do you smoke?
• Are you pregnant?
In addition to exercise intensity, medications for heart conditions, blood pressure, psychological conditions, asthma,
breathing, etc., as well as some energy drinks, alcohol,
nicotine and drugs may also affect heart rate.
It is important to be sensitive to your body’s responses
during exercise. If you feel unexpected pain or excessive
fatigue when exercising, it is recommended that you stop
the exercise or continue at a lighter intensity.
Note! If you are using a pacemaker, you can use Polar
training computers. In theory interference to pacemaker
caused by Polar products should not be possible. In
practice no reports exist to suggest anyone ever having
experienced interference. We cannot however issue an
offi cial guarantee on our products’ suitability with all
pacemakers or other implanted devices due to the variety
of devices available. If you have any doubts, or if you
experience any unusual sensations while using Polar
products, please consult your physician or contact the
implanted electronic device manufacturer to determine
safety in your case.
If you are allergic to any substance that comes into
contact with your skin or if you suspect an allergic
reaction due to using the product, check the listed
materials on page 58. To avoid any skin reaction to the
transmitter, wear it over a shirt. However, moisten the shirt
well under the electrodes to ensure fl awless operation.
Note:
The combined impact of moisture and intense
abrasion may cause a black color to come off the
clothes. If you use insect repellent on your skin, you
must ensure that it does not come into contact with the
transmitter.
Training equipment with electronic components may
cause interfering stray signals. To tackle these problems,
try the following:
1. Remove the transmitter from your chest and use the
training equipment as you would normally.
2. Move the wrist unit around until you fi
nd an area in
which it displays no stray reading or does not fl ash the
heart symbol. Interference is often worst right in front
of the display panel of the equipment, while the left or
right side of the display is relatively free of disturbance.
3. Put the transmitter back on your chest and keep the
wrist unit in this interference-free area as much as
possible.
If the CS100 still does not work, the piece of equipment
may be electrically too noisy for wireless heart rate
measurement.
ENGLISH– 55
9. FREQUENTLY ASKED QUESTIONS
What should I do if...
...the display of the cycling computer is blank?
If you are using the cycling computer for the fi rst time:
The cycling computer is in battery saving mode when it is
dispatched from the factory. To activate it, press the MIDDLE button
twice. The Basic Settings starts. For further information, see page 8.
If you have been using the cycling computer before:
The cycling computer goes to the power save mode (blank), if you
do not press any button in the Time mode for fi ve minutes. You
can turn the cycling computer on again by pressing any button.
Alternatively the battery may be dead (see the next question for
further instructions).
...the battery of the cycling computer must be replaced?
We recommend having all service done by an authorized Polar
Service Center. This is especially necessary to ensure that the
guarantee remains valid and is not affected by incorrect repair
procedures performed by an unauthorized agent. Polar Service
will test your cycling computer for water resistance after battery
replacement and make a full periodic check of the complete cycling
computer set.
56 – ENGLISH
...there are no reactions to any buttons?
If there are no reactions to any buttons, reset the cycling computer.
Resetting only clears the date and time, not the recorded Files or
Totals. Reset the cycling computer by pressing and holding all
buttons until the display is fi lled with digits. By pressing any button
the cycling computer goes to the Basic Settings mode (BASIC SET
is displayed). For further information, see page 8. If this does not
work, have the batteries checked.
Note: If you do not press any button after you reset the cycling
computer, within one minute the cycling computer goes to the Time
mode.
symbol is activated?
...the
Usually the fi rst sign of an expiring battery is the low battery
indicator
Note: Due to cold conditions the low battery indicator may
appear, but the indicator disappears when you return to a warmer
temperature.
...another person with a cycling computer or a heart rate monitor
is causing interference?
Move away from that person and continue your exercise normally.
Alternatively, to avoid other person’s heart rate signals:
1.
from the person with the other device.
2. Put the transmitter back on and bring the cycling computer up
to your chest near the transmitter’s Polar logo. The cycling
computer will start looking for a heart rate signal again.
Continue your exercise normally.
on the display. For further information, see page 51.
ake the transmitter off your chest for 30 seconds. Stay away
T
...the cycling computer does not measure the calories?
In order to measure the calories you burn, you need to wear the
transmitter during recording.
...the heart rate, speed or distance reading becomes erratic or
extremely high?
Strong electromagnetic signals can cause erratic readings. So move
away from possible sources of disturbance such as high-voltage
power lines, traffi
bike computers, some motor
c lights, electric railways or trams, car motors,
-driven exercise equipment (like fi tness
testers) or cellular phones.
If the erratic heart rate reading continues after you have moved
away from the source of disturbance, slow down your speed and
check your pulse manually
reading on the display
. If you feel it corresponds to the high
, you may be experiencing cardiac arrhythmia.
Most cases of arrhythmia are not serious, but consult your doctor
nevertheless.
To avoid crosstalk from another cyclist with a speed sensor, keep a
distance of at least one meter/ 3’4’
and the speed sensor of the other cyclist.
’ between your cycling computer
...there is no heart rate reading (00)?
Check that the electrodes of the transmitter are moistened and
•
that you are wearing it as instructed.
• Make sure the transmitter is clean.
• Check that you are not near high voltage power lines,
televisions, cellular phones, or other sources of electromagnetic
interference. Also make sure that you are not near (1 m/3 ft)
other heart rate monitor users, when starting your exercise
recording.
• Cardiac arrhythmia may cause irregular readings or a cardiac
event may have altered your ECG waveform. In these cases,
consult your physician.
...there is no speed reading while cycling?
Check the correct position and distance of the sensor with the
•
magnet and the cycling computer.
• Check that you have set the correct cycling settings in your
cycling computer. For further information, see page 39.
• If the 00 reading appears irregularly, this may be due to
temporary electromagnetic interference in your current
surroundings.
• If the 00 reading is constant, you may have exceeded
4500 riding hours and the battery is empty.
ENGLISH– 57
10. TECHNICAL SPECIFICATIONS
Cycling computer
Material: Thermoplastic polymer case
Watch accuracy: better than ±0.5 seconds per day at
25 °C/ 77 °F temperature.
Heart rate accuracy: ±1% or 1 bpm, whichever larger, the defi nition
applies to steady state conditions. Heart rate is displayed as number
of heartbeats per minute (bpm) or as % of your maximum heart rate.
Heart rate measuring range: 15-240
Maximum time recorded to File:
Limited values of information
to the exersice fi le:
Current speed display range: 0-127 km/h or 0-75 mph
Operating temperature: -10 °C to +50 °C / +14 °F
to +122 °F
Battery life: Average 2 years in normal use
(1 h/day, 7 days/week)
Battery type: CR 2032
Battery sealing ring: OR 23.6 x 1.0 (silicon rubber)
99 h 59 min 59 s
1 training fi le
Transmitter
Battery life: Average 2500 hours of use
Battery type: Built-in Lithium Cell
Operating temperature: -10 °C to +50 °C / +14 °F to +122 °F
Transmitter material: Polyurethane
58 – ENGLISH
Elastic strap
Buckle material: Polyurethane
Fabric material: Nylon, polyester, and natural rubber,
including a small amount of latex
Speed sensor
Speed sensor battery life: Average 4500 hours of use
Accuracy: ±1 %
Material: Thermoplastic polymer case
Operating temperature: -10 °C to +50 °C / +14 °F to +122 °F
SYSTEM REQUIREMENTS
Polar UpLink Tool
– PC
– Microsoft Windows XP/Vista/7
– Sound card
– Dynamic loudspeakers or headphones
The Polar CS100 cycling computer applies the following patented
technologies, among others:
• OwnZone
®
assessment for determining personal target heart rate
limits for the day
Water resistance of Polar products is tested according to International Standard ISO 2281. Products are divided into three different categories
according to their water resistance. Check the back of your Polar product for the water resistance category and compare it to the chart below.
Please note that these defi nitions do not necessarily apply to products of other manufacturers.
Marking on the
case back
Water resistant
Water resistant
30m / 50m
Water resistant 100m
Wash splashes, sweat,
raindrops etc.
X
X
X
Bathing and
swimming
X
X
Skin diving with
snorkel (no air tanks)
X
SCUBA diving
(with air tanks)
Water resistant
characteristics
Splashes, raindrops etc.
Minimum for bathing
and swimming
For frequent use in water
but no SCUBA diving
ENGLISH– 59
11. LIMITED POLAR INTERNATIONAL GUARANTEE
• This guarantee does not affect the consumer’s statutory rights under applicable national or state laws in force, or the consumer’s rights
against the dealer arising from their sales/purchase contract.
• This limited Polar international guarantee is issued by Polar Electro Inc. for consumers who have purchased this product in the USA or
Canada. This limited Polar international guarantee is issued by Polar Electro Oy for consumers who have purchased this product in other
countries.
• Polar Electro Oy/Polar Electro Inc. guarantees the original consumer/purchaser of this device that the product will be free from defects in
material or workmanship for two (2) years from the date of purchase.
• The receipt of the original purchase is your proof of purchase!
• The guarantee does not cover the battery, normal wear and tear, damage due to misuse, abuse, accidents or non-compliance with the
precautions; improper maintenance, commercial use, cracked, broken or scratched cases/displays, elastic strap and Polar apparel.
• The guarantee does not cover any damage/s, losses, costs or expenses, direct, indirect or incidental, consequential or special, arising out
of, or related to the product.
• Items purchased second hand are not covered by the two (2) year warranty, unless otherwise stipulated by local law.
• During the guarantee period, the product will be either repaired or replaced at any of the authorized Polar Service Centers regardless of the
country of purchase.
Guarantee with respect to any product will be limited to countries where the product has been initially marketed.
This product is compliant with Directives 93/42/EEC, 1999/5/EC and 2011/65/EU.
0537
The relevant Declaration of Conformity is available at www.polar.com/support.
This crossed out wheeled bin marking shows that Polar products are electronic devices and are in the scope of Directive 2002/96/EC
of the European Parliament and of the Council on waste electrical and electronic equipment (WEEE) and batteries and accumulators used in products are in the scope of Directive 2006/66/EC of the European Parliament and of the Council of 6 September 2006
on batteries and accumulators and waste batteries and accumulators. These products and batteries/accumulators inside Polar
products should thus be disposed of separately in EU countries.
This marking shows that the product is protected against electric shocks.
60 – ENGLISH
12. POLAR DISCLAIMER
• The material in this manual is for informational purposes only. The products it describes are subject to change without prior notice,
due to the manufacturer’s continuous development program.
• Polar Electro Inc./Polar Electro Oy makes no representations or warranties with respect to this manual or with respect to the products
described herein.
• Polar Electro Inc./Polar Electro Oy shall not be liable for any damages, losses, costs or expenses, direct, indirect or incidental,
consequential or special, arising out of, or related to the use of this material of the products described herein.
This product is protected by one or several of the following patents:
FI68734, DE3439238, GB2149514, HK812/1989, US4625733, FI88223, DE4215549, FR92.06120, GB2257523, HK113/1996, SG9591671-4,
US5491474, FI88972, FR92.09150, GB2258587, HK306/1996, SG9592117-7, US5486818, FI96380, US5611346, EP665947, DE69414362,
FI4150, DE20008882.3, US6477397, FR0006504, FI4069, DE29910633, GB2339833, US6272365, FI107776, US6327486, FI110915,
US6537227, US6277080, FI111514, GB2326240, US6361502, US6418394, US6229454, EP836165, FI100924, WO96/20640, US6104947,
US5719825, US5848027, EP1055158, US6714812, FI88972, FR92.09150, GB2258587, HK306/1996, SG9592117-7, US5486818.
Other patents pending.