Plus M-18 Series, N-20 Series Assembly Manual

M-18/N-20 Series Copyboard

Stand Assembly Manual

This is the stand assembly manual for the M-18 and N-20 Series Copyboard.
The copyboard is referred to as "the set" or "the main unit" below.

WARNING

• Only specially trained technicians should perform installation operations.

• Please be sure to perform the installation and assembly based on this manual. Incorrect installation or assembly will be the cause of injury.

• Please have 2 or more persons lift the main unit when installing or removing it.

• For details on installation, also refer to the main unit’s “User’s Manual” and “Assembly and Setup Manual”.

• Remove the 4 stabilizers and unlock the caster stoppers before moving the stand.To prevent the toppling, be sure to remove the stabilizers
and unlock the stoppers.The toppling of the unit may result in bodily injury or damage to the machine.

CAUTION

• When mounting the printer on the main unit, attach the *Velcro to prevent the printer from slipping out due to vibrations.
Remove the printer when moving the main unit. If not, the printer may fall, resulting in damage or injury.

* The Velcro is meant to prevent slipping, not to fasten the printer in place.
* Velcro is a registered trademark of Velcro Industries.

Note

• Diagrams of printers that appear in this manual are representative illustrations.
The illustration may differ from the actual printer. Check the owner's manual of your printer for information about the names of the connectors and

their locations and use.

STAND PACKAGING LIST

Please open the carton and check the parts.
In the rare event that something is missing, please contact your store of purchase.

Name Assembly parts

T-shape legs (with casters) : 2 Screw caps: 2

Locking knobs 2
Cable cover: Mounted on stand

Horizontal bars:1 Mount screws (M5 x 20 mm):2

(temporarily fastened on side bar)
Mount screws (M5 x 45 mm): 2
Sleeves: 2
Plain washer :2

Stabilizers:4 Hexagonal socket screws

Printer table/AC power adapter box: 1 set
(mounted on side bar)
Velcro: 2 sets
Hexagonal wrench
(width across flats: 3 mm): 1

Name Assembly parts

ASSEMBLY OF THE STAND

Preparation:

For the mounting instruction, please refer to the “Assembly and Setup Manual”.

1. Lock the caster stoppers.

Press the bottom portion of the stoppers down to lock them.

CAUTION

• Lock the casters of the T-shaped feet (left and right). If not, the stand could
slip, causing the stand or main unit to fall and resulting in injury or damage.

Mount the pen tray on the main unit.

(M5 x 8mm):8

Caster

2. Mount the T-shaped feet to the side bar.

The shorter side of the T-shaped foot is the back of the stand. The diagrams show the procedure from the back side.

Set the T-shaped foot with the cable cover on the right side (the printer table side).



Remove the temporary fixing tape from the ends of the side bar.

1

Temporary fixing tape

Temporary fixing
tape

Side bar

M5 screw
(mounted on
side bar)

Space of about 2 mm



Insert the side bar's screw head into the T-shaped foot's screw hole (on the top), slide downwards, then use the

hexagonal wrench to partially fasten.



Insert the M5 x 45 screw and Plain washer into the sleeve, then use the hexagonal wrench to partially fasten it to the

side bar.

• Check that the sleeve is not sticking out.

• Once mounting of the left and right T-shaped feet is completed, tighten the four screws, adjusting so there is no looseness.



Fasten the screw caps to the screw heads of the left and right T-shaped feet.

A: With the screw caps set slightly at an angle, place the hooks into the screw holes in the T-shaped feet and slide downwards.

B: Press the stoppers of the screw caps into the hollows in the M5 screw heads.

2 3

Sleeve

Hexagonal
wrench

4

Screw hole

A. Hook

Screw cap

* The diagram used for

explanation here is
see-through.

Side bar

Hexagonal
wrench

Front (long)

Back (short)

Plain washer

M5 x 45 mm screw

B. Stopper

M5 screw head

Cable cover

Printer table

Side bar

3. Attach the stabilizers to the front and back of the T-shaped feet.

CAUTION



Alignment of the screw holes of the T-shape feet with those of the

stabilizers.

Slide the stabilizers on the T-shaped feet to align with the holes.

CAUTION



Secure the stabilizers on the T-shape feet by hexagonal screws

using hexagonal wrench.

Attach the 4 stabilizers on the feet.

• To prevent toppling, be sure to install the stabilizers at each of the 4 locations. The toppling of this
machine could cause bodily injury or damage the machine.

T-shape foot

• Do not lift the stand to work on it. This may lead
to toppling or bodily injury.

Stabilizer

Hexagonal socket screws
(M5 x 8mm)

Hexagonal wrench