Plus M-11series, C-11 series Assembly And Setup Manual
M-11 Series Copyboard/C-11 Series Captureboard
Assembly and Setup Manual
This is the installation and assembly manual for the M-11 series/C-11 series.
To the Customer
Specialized techniques are required in the wall mounting of the Copyboard. Please do not
attempt any installation work unless you have the techniques.
To the Dealer or Installation Tradesman
In the interest of the safety of the customer, please perform installation work paying due
attention to the strength of the installation location to ensure that it can bear the load of
the Copyboard, printer, and installation parts.
TABLE OF CONTENTS
1. Please Read in the Interest of Safety ........................................................2
2. Packaging List ............................................................................................. 2
3. Copyboard Installation Procedure ............................................................ 3
4. Assembly of the stand ................................................................................ 3
5. Wall Mounting..............................................................................................6
6. Assembly of the Printer Table .................................................................... 9
7. Printer Installation .................................................................................... 11
8. Test Print....................................................................................................13
9. Changing the Height of the Unit ..............................................................14
2
1. PLEASE READ IN THE INTEREST OF SAFETY
Warning
• Please be sure to perform the installation and assembly based on this manual. Incorrect installation or assembly will be the cause of injury.
• Please have 2 or more persons lift the Copyboard when installing or removing it.
• To prevent dropping the strength of the installation location and the anchoring method must fully bear over a
long period the load of the Copyboard, printer, and installation parts. The installation should also be performed
to fully withstand an earthquake. Incorrect installation can result in the Copyboard falling and causing injury.
• Please use M6 or equivalent screws for the wall mounting portion. Use of screws other than M6 or equivalent
can result in the Copyboard falling and causing injury.
• Please mount to a post in the wall or a sturdy wall stud. When the mounting positions of the Copyboard are not
reached, please use optional wall support fittings.
• Please use hardware like anchor nuts and anchor bolts for mounting on a concrete wall.
• Be sure to install the stabilizers supplied with the stand at each of the 4 locations (to prevent toppling).
Warning
• When a printer has been installed on the Copyboard and the printer table is larger than the printer with vacant
space remaining, be sure to attach the printer guides. Failing to do so could result in the printer falling when the
Copyboard is moved and this could cause damage or injury.
2. PACKAGING LIST
Please open the carton and check the parts.
In the rare event that something is missing, please contact your store of purchase.
■ Printer package*: One unit
Please check the user’s manual of the printer for a list of contents for the printer package.
Note
A printer is not packaged together with the C-11 Series. It is an item that is sold separately.
■ Copyboard packaging list
Copyboard: 1 unit (standard type or wide type)
Wall mounting brackets: × 4, M4×8 screws × 16 (for wall mounting)
Printer table (1 set): Printer table × 1, Brackets × 2, M4×8 screws × 4, M3×6 screws × 12, Cushions × 2, Printer guides × 3,
20 cm cable ties × 2, 10 cm cable ties: × 2
Cable clips: × 5 (for fastening the power cable and USB cable)
AC power adapter (with power code): × 1 (HEC-AP065-24V)
Markers: × 4 (One each of black, red, blue, and green)
Eraser: × 1
USB cable: × 1
Documentation: Instruction manual × 1, CD-ROM × 1, Quick Guide × 1, Assembly and Setup Manual (this manual) × 1
Captureboard Software Operation Manual*1 × 1
*1 is only packaged together with the C-11 Series.
■ Stand packaging list*
T-shape legs (with casters) × 2, Hexagonal socket screws × 8, Flat washers × 8, Horizontal bars × 2, Hexagonal wrench × 1,
Stay × 1, Nylon bushing × 1, M3×6 screws × 2, Stabilizers × 4, Frame caps × 2, Auxiliary caps × 4, Lock-screws × 2
* The printer and stand may be options.
(The packaged contents will differ depending on the purchased Series.)
3
3
4
1
2
3
4
1
2
● When using the stand
Assembly of the stand See Page 3
* The stand may be an option.
* The printer may be an option.
Assembly of the printer table See Page 9
Printer installation See Page 11
Test print See Page 13
Wall mounting See Page 6
Assembly of the printer table See Page 9
Printer installation See Page 11
Test print See Page 13
● When mounting to a wall
(Please consult with a dealer or installation tradesman. Installation work should not be done by the customer.
The installation method will change depending on the type of installation. Please perform installation and assembly according to the following procedures.
3. COPYBOARD INSTALLATION PROCEDURE
4. ASSEMBLY OF THE STAND
Frame Cap
Stabilizer
T-shape leg
Note
• Diagrams of printers that appear in this manual are representative illustrations.
The illustration will differ from the actual printer. Check the owner's manual of your printer for information about the names of the connectors
and their locations and use.
Caster
Stabilizer
Use the same method to assemble the left and right
sides of the stand.
(1) Press-fit the frame cap onto the top
of the T-shaped legs.
(2) Attach the stabilizers to the front and
back of the T-shaped legs.
Insert the stabilizers securely all the way in.
(3) Lock the caster stoppers.
Press the bottom portion of the stoppers to lock them.
CAUTION
To prevent toppling, be sure to install the stabilizers
at each of the 4 locations. The toppling of this machine could cause bodily injury or damage the machine.
4
(4) Attach the two horizontal bars to the
T-shape legs.
Use hexagonal socket screws (M5) and flat
washers (M5) to attach.
Partially fasten using the hexagonal wrench (M5), then
tighten securely after the upper and lower horizontal
bars have been attached.
(5) Place the stand’s hooks in the mount-
ing holes in the support fittings and
insert the grooves in the hooks securely.
There are 3 hole positions. By changing the position,
the installation height can be changed among 3 levels in 100 mm units (1770, 1870, and 1970 mm (the
maximum height)).
(6) Mount the printer table to the Copy-
board.
See Page 9 for information about the assembly and
installation of the printer table.
* Installation of the printer table is not required when
the Copyboard is used only for USB memory storage.
Hexagonal wrench (M5)
T-shaped leg
Horizontal bar
Hexagonal socket screw (M5)
Flat washer (M5)
CAUTION
Please have 2 or more persons lift the Copyboard
when installing it or making a height adjustment. If
the unit is dropped or falls over, this could cause unforeseen injury.
Check that the hook is securely inserted into the installation hole. Insecure installation could result in
the unit falling and causing bodily injury or damage
to the unit.
Mounting hole
Hook
The rear
frame
5
(7) Install the stay to the printer table.
햲 Insert the nylon bushing into the stay.
햳 Insert the stay into the pipe of the stand.
햴 Mount the stay to the printer table using two M3 screws.
Notice
Check again that the grooves in the stand’s hooks are securely inserted
in the mounting holes in the support fittings.
(8) Lock the main unit and stand with the two
locking knobs.
3
2
Stay
Pipe
M3 screws
Locking knobs
Stay
Nylon bushing
Loading...