Plextor PX-W4012TSe, PX-W4012TS, 401240SE, 401240SI, PlexWriter 40/12/40S Installation And User Manual
Page 1
PX-W4012TS (Internal)
PX-W4012TSe (External)
Models:
INSTALLATION AND USERS MANUAL
SCSI CD-R/CD-RW DRIVE
APRIL 2003
Page 2
Plextor reserves the right to make improvements in the products described in this
manual at any time without prior notice.
Plextor makes no representation or warranties with respect to the contents hereof
and specifically disclaims any implied warranties of merchantability or fitness for
any particular purpose. Further, Plextor Corp. reserves the right to revise this manual
and to make changes in its content without obligation to notify any person or
organization of such revision or change.
This manual is copyrighted, all rights reserved. It may not be copied, photocopied,
translated, or reduced to any electronic medium or machine-readable form without
Plextor’s prior permission.
Manual copyright ©2003 Plext
or Corp. Third edition, April 2003.
Licenses and Trademarks
Plextor and the Plextor logo are registered trademarks of Plextor Corp; and PlexWri t er,
PoweRec is a trademark of Plextor Corp. Other brands and products are trademarks of their
respective holders.
Record Your Serial Number
For future reference, record the serial number and the TLA code (found on your
drive’s label) in the space provided below.
TLA/Firmware Revision Number
Page 3
FCC NOTICE
This equipm ent has been tested and fou nd to comply with the limit s for a Subpart B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee interference will not occur in a
particular installation. If this equipment causes harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications should be approved by the party responsible for compliance with FCC
Rules; otherwise, the user loses authority to operate the equipment.
LASER INFORMATION
These products have been designed and m anufactured according to IEC 60825-1 on the safety of laser
products. This p roduct comes under “Class 1 Laser Products.”
CAUTION
specified herein may result in hazardous radiation exposure.
: Use of controls or adjustments or performance of procedures other than those
A Laser Caution Label is attached on the t op of the internal drive model or the bottom of the external
drive. The label reads:
“CAUTION – CLASS 3B INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO
THE BEAM.”
Detail of Laser Caution Labels Top View of Internal Drive or
Bottom View of External Drive
Showing Location of
Laser Caution Labels
The laser beam emitted from the optical pickup is invisible. Accordingly:
•
Do not open the optical pickup housing.
•
Obtain service only from experienced personnel.
CAUTION
: To disconnect the CD drive from an electrical current, pull out the power plug.
Page 4
Ü
VORSICHT
Zur Einhaltung der Funk-Entstörung von nicht selbständig betreibbaren
Hochfrequenzgeräten (periphere Anlagenkomponenten).
Dieses Gerät entspricht als Einzelgerät den Funk-Entstöranforderungen der
Postverfügung Nr. 243/1991.
Wird das Gerät innerhalb einer Anlage zusammen mit anderen Geräten
betrieben, so muss bei Inanspruchnahme der “Allgemeinen (Betriebs-)
genehmigung” nach der BMPT-AmtsblVfg Nr. 243/1991 die gesamte
Anlage folgenden Richtlinien entsprechen:
•
•
Dies ist bei der Zusammensetzung einer Anlage (z.B. Computersystem) aus nur einzeln geprüften Geräten
nicht immer erfüllt.
: DIE TRENNUNG VOM NETZ ERFOLGT DURCH ZIEHEN DES NETZSTECK ERS.
G-Vfg.243
Grenzwertklas se B der EN55022
Auflagen nach § 2 der BMPT-AmtsblVfg 243/1991
Page 5
Table of Contents
1. Getting Started.................................................................................................1
About this Manual.............................................................................................. 1
Meet Your PlexWriter 40/12/40S ......................................................................1
What the PlexWriter 40/12/40S Does............................................................ 1
Features of the PlexWriter 40/12/40S............................................................2
Minimum Configuration to Use the PlexWriter 40/12/40S ........................... 2
What You Can Do with the PlexWriter 40/12/40S........................................3
What's in the Box...............................................................................................3
Save Your Box!.............................................................................................. 3
PlexWriter Drive Features and Controls............................................................ 4
Front Panel—Internal SCSI Drive ................................................................. 4
Front Panel—External SCSI Drive ................................................................ 4
Rear Panel—Internal SCSI Drive .................................................................. 6
Rear Panel—External SCSI Drive .................................................................7
About Software.................................................................................................. 8
Precautions.........................................................................................................8
2. Installing Your PlexWriter.............................................................................. 9
Quickstart SCSI Installation—For Experienced PC Users Only.................... 9
Set SCSI Drive Jumpers..................................................................................... 10
Do I Have to Change My PlexWrit er’s SCSI ID Number?............................ 10
Do I Have to Change My PlexWrit er’s SCSI Termination Setting?..............12
Do I Have to Change Other PlexWriter SCSI Settings?................................ 13
Setting Jumpers on a PlexWriter Internal SCSI Drive................................... 14
Setting Switches on a PlexWriter External SCSI Drive.................................17
Install a PlexWriter Internal SCSI Drive............................................................18
Record the Serial Number and TLA Code.....................................................18
Mount the PlexWriter Internal SCSI Drive.................................................... 18
Install a PlexWriter External SCSI Drive...........................................................24
Connect a Single External SCSI Drive .......................................................... 25
Connect Multiple External SCSI Drives........................................................ 26
Starting an External PlexWriter..................................................................... 27
Using Sound Boards and Audio Cables.............................................................27
What Else Do I Need?........................................................................................ 28
Recording Software........................................................................................28
SCSI Adapter Drivers ....................................................................................28
3. Using Your PlexWriter....................................................................................29
What Media to Use ............................................................................................ 29
Achieving Maximum Rated Writing Speed...................................................29
Writing at Lower Speeds................................................................................ 29
Tray Loading and Operation.............................................................................. 30
Handling CD Media.......................................................................................30
Cleaning Discs ............................................................................................... 31
Using the Writing Speed Indicators................................................................... 31
PlexWriter 40/12/40S Installation and Users Manual v
Page 6
Table of Contents
Advantages of BURN-Proof Technology.......................................................... 32
Advantages of VariRec Technology.................................................................. 32
How the Default VariRec Setting Is Determined...........................................32
Changing the VariRec Setting ........................................................................ 33
When You Write with VariRec......................................................................33
4. Maintenance and Troubleshooting.................................................................35
Upgrading Firmware..........................................................................................35
Troubleshooting .................................................................................................35
Using the Self-Test Diagnostics.........................................................................36
Performing the Self-Test on an Internal Drive...............................................36
Performing the Self-Test on an External Drive..............................................38
After the Self-Test .......................................................................................... 40
Appendix A: PlexWriter Specifications..............................................................41
Appendix B: Technical Support..........................................................................47
How to Contact Plextor Technical Support........................................................47
Before You E-mail/Log On/FAX/Call...............................................................48
Returns............................................................................................................... 48
Contacting Plextor’s RMA Department.........................................................49
Packing Your Drive........................................................................................49
Shipping Your Drive to Plextor......................................................................49
Appendix C: Warranty........................................................................................51
If You’re Outside the U.S. or Canada................................................................52
Index......................................................................................................................53
vi
PlexWriter 40/12/40S Installation and Users Manual
Page 7
1. Getting Started
Congratulations! Thank you for purchasing the Plextor® PlexWriter™ 40/12/40S, a
reliable, high-performance CD rewriter, recorder and reader that connects to your
computer with a SCSI cable. We appreciate the confidence you have shown in us.
Our goal is to put you—and keep you—on the leading edge of CD technology.
About this Manual
This manual explains how to connect and use your internal or external PlexWriter
40/12/40S drive. The installation process is simple. And if you have problems,
Plextor’s technical support staff is here to help.
Please read this manual carefully and keep it handy for easy reference. Use the
manual for installation, operation and troubleshooting. See your dealer or call
Plextor’s Technical Support Department if your drive needs service. And if you run
into a problem that doesn't seem to be covered, please contact us. (See “Appendix B:
Technical Support” for the different ways you can contact us.) You will be
connected to our friendly, helpful band of tech support engineers. What might seem
like an uncooperative drive to you could very well be a 30-second repair to them.
But we will never know unless you contact us.
Meet Your PlexWriter 40/12/40S
The PlexWriter 40/12/40S is a CD-ReWritable drive that provides professional
quality CD performance for writing, rewriting and reading. It is available as an
internal drive or an external drive, with an internal or an external SCSI interface,
respectively.
What the PlexWriter 40/12/40S Does
The PlexWriter 40/12/40S:
•
Writes data and CD-DA (digital audio) to CD-R (recordable CD) media at up to
40X speed.
•
Writes to high speed CD-RW (rewritable CD) media at up to 12X speed.
(Naturally, the drive can also write to conventional CD-RW media at 4X speeds.)
•
Reads all CD-ROM and CD-R media at a maximum of 40X speed with an
average access time of less than 120 milliseconds. (Maximum read speed of
CD-RW media is 32X.)
PlexWriter 40/12/40S Installation and Users Manual 1
Page 8
Section 1. Getting Started
Features of the PlexWriter 40/12/40S
•
Ultra SCSI-3 interface: Small Computer Systems Interface (SCSI) lets you
connect up to seven devices on the same line.
•
Orange Book compatibility: Compatible with Orange Book, Parts II and III.
•
MMC compliance: Supports the MMC-3 command set.
•
Variety of recording modes: Supports track-at-once, disc-at-once, session-atonce, and multi-session, as well as variable and fixed packet writing.
•
UDF support: UDF file system implemented through packet writing.
•
Plug and Play: Supports Windows Plug and Play.
•
Flash memory: Allows upgrading the PlexWriter to the latest firmware revision
(available from the Plextor web site) without opening the computer or physically
accessing the drive.
•
OPC and ROPC: Optimum Power Control and Running Optimum Power
Control, which adjust the laser power for the optimum write strategy.
•
PoweRec: Plextor Optimized Writing Error Reduction Control (PoweRec)
extends OPC and ROPC to adjust laser power and writing speed so they’re at the
optimum settings for that particular disc.
•
VariRec: Lets you record at low speeds (1X and 4X) for highest quality, while
providing user adjustment of the recording power above or below a default level.
This adjustment lets you customize the opti mum laser p ower to your own needs.
•
BURN-Proof: With 4-megabyte buffer, eliminates buffer underrun errors, so you
can safely use your computer for other tasks while you’re writing to a CD-R or
CD-RW disc.
•
Mt. Rainier (MRW) functionality: Ready for Mt. Rainier.
•
Self-diagnostics: The drive can actually determine if it is working properly, an
invaluable feature for troubleshooting.
Minimum Configuration to Use the PlexWriter 40/12/40S
•
Computer: Pentium II 300-MHz CPU or faster.
•
Mi n imum RAM: 64 MB.
•
Interface: Ultra SCSI-3, 50-pin.
•
Hard disk size: To write to a CD in image mode (that is, to write an image of a
CD to your hard disk), you need 1 GB of free space.
2
PlexWriter 40/12/40S Installation and Users Manual
Page 9
Section 1. Getting Started
What You Can Do with the PlexWriter 40/12/40S
Just look at some of the things you can do with your PlexWriter 40/12/40S:
•
Record data or audio onto writable or rewritable CD media.
•
Play music CDs.
•
Save photos and other images on rewritable or writable CDs.
•
Share information with colleagues—just use software such as Roxio’s DirectCD
to drag and drop files onto CD-R or CD-RW media, then continue adding files
and sharing the same CD disc.
•
Archive images and video to CD.
•
Master new software programs on CD.
What's in the Box
What you find in your Plextor box depends on what the company that sold you the
box put in—or took out—while the Plextor drive was in their possession.
NOTE
: This applies to the Plextor retail box. Your box’s contents may be different.
In the box you’ll find:
•
PlexWriter 40/12/40S CD-RW drive
•
SCSI cable
•
Emergency eject tool
•
4 mounting screws (internal dri ve only)
•
Quick install guide
•
Extra jumpers for setting drive options (internal drive onl y)
•
1 piece of approved CD-R media
•
Plextor CD with authoring software bundle
•
PlexWriter 40/12/40S Installation and Users Manual
•
AC power cord (external drive only)
If your drive came pre-installed,
some or all of the items above may
have been installed and may not be
separately available. See the Plextor
web site for locations to purchase
additional or replacement
accessories.
If the security sticker on top of your
box is cut, there may be a good
reason: for example, a dealer may
have added other components or
software. Carefully check the
contents to ensure everything is
present. If something is missing, contact the party from whom you purchased the
box.
Save Your Box!
Be sure to save t he box after you have
installed your PlexWriter drive. The
box and its packaging material were
designed and drop tested to ensure your
PlexWriter can endure rough treatment
and still arrive in working order. If you
have to ship your drive back to Plextor,
you’ll want to send it in the original
box. (For more details about returning
your drive to Plextor, see page 48.)
PlexWriter 40/12/40S Installation and Users Manual 3
Page 10
Section 1. Getting Started
PlexWriter Drive Features and Controls
Use these illustrations to become familiar with your drive’s controls and features.
Front Panel—Internal SCSI Drive
Figure 1: Front Panel of the PlexWriter 40/12/40S Internal Drive
Front Panel—External SCSI Drive
Figure 2: Front Panel of the PlexWriter 40/12/40S External Drive
4
PlexWriter 40/12/40S Installation and Users Manual
Page 11
Section 1. Getting Started
•
Tray front door: Attached to tray drawer.
•
Emergency eject hole: Insert emergency eject tool, paper clip, or other thin,
rigid object to eject tray if automatic eject button does not work. Turn OFF power
before usi ng this feature.
•
Headphone jack: Stereo mini-jack for headphones and powered speakers.
•
Volume control: Controls volume of headphone jack.
NOTE
: The volume control on the front panel of your drive adjusts only the sound
level of the headphone jack. It has no impact on the volume level of the rear-panel
audio outputs.
•
DISC indicator: Green when disc is in the drive and power is ON.
•
ON/READ indicator: Green when power is ON and no disc is in drive. Green
flashing when disc is being read. Green when BURN-Proof active during writing.
•
WRITE L indicator: Amber when recording CD-R discs at 1X-24X speed, or
CD-RW discs at 4X or 10X speed.
•
WRITE H indicator: Amber when recording CD-R discs at 32X and 40X speed,
or CD-RW disc at 12X speed.
Blink interval:
40-millisecond blink interval: Recording CD-R at 40X
80-millisecond blink interval: Recording CD-R at 32X or CD-RW at 12X
•
CD-audio play/skip forward butt on: With an audio CD in the drive, push once
to begin playing an audio CD. Push the button multiple times to skip to a selected
track (e.g., press three times to reach track 3). Push and hold down this button
more than one second to fast forward.
•
Stop/eject button: Push to eject tray. During CD play mode, press once to stop
playback; press twice to eject the disc.
•
Power switch (external drive): To turn the drive’s power ON or OFF.
PlexWriter 40/12/40S Installation and Users Manual 5
Page 12
Section 1. Getting Started
Rear Panel—Internal SCSI Drive
•
Figure 3: Rear Panel of the PlexWriter 40/12/40S Internal Drive
Audio output connector: Outputs stereo analog signal. Use to connect to sound
board or audio amplifier. Use standard MPC-3 type, 4-pin connector.
•
Jumpers: Use to select SCSI ID, parity, SCSI termination, or block size. Leave
these jumpers at their factory settings unless one or more of the following
situations pertains to you:
SCSI ID: If you are using more than one SCSI peripheral, you may have to
change your SCSI ID number; see page 10 for details.
PRTY: Parity. In some cases, you may need to turn parity off; see page 13.
TERM: SCSI termination. In some situations, you may need to set this
jumper to turn the PlexWriter’s SCSI termination off; see page 12 for details.
TEST: For factory use only. Do not change this setting.
BLOCK: Block size. Yo u may need to change this setting if you are
working in a UNIX environment and want to boot from your PlexWriter; see
page 13.
SPDIF: Sony/Philips digital interface (digital audio out). If your sound
board supports the Sony/Philips digital interface, you can connect it here.
•
SCSI interface connector: Connects to SCSI interface board using
50-pin-to-50-pin flat ribbon SCSI cable.
•
Power connector: Connects to your computer’s power supply to provide
DC +5V and +12V to the PlexWriter.
6
PlexWriter 40/12/40S Installation and Users Manual
Page 13
Rear Panel—External SCSI Drive
Section 1. Getting Started
Figure 4: Rear Panel of the PlexWriter 40/12/40S External SCSI Drive
•
AC power input: Use the power cord supplied with your drive.
•
SCSI ID dial: Use this dial to designate SCSI ID numbers. Rotate the dial to
change the number. If you are using more than one SCSI peripheral, you may
need to change your SCSI ID number; see page 10.
•
DIP switches: Use to select parity, SCSI termination or block size. Leave these
switches at their factory settings unless one or more of the following situations
pertains to you:
PRTY: Parity. In some cases, you may need to turn parity off; see page 13.
TERM: SCSI ter mination. In some situations, you may need to set this
jumper to turn the PlexWriter’s SCSI termination off; see page 12 for details.
TEST: For factory use only. Do not change this setting.
BLOCK: Block size. Yo u may need to change this setting if you are
working in a UNIX environment and want to boot from your PlexWriter; see
page 13.
•
Audio output connectors: Output stereo analog signal. Use to connect to sound
board or audio amplifier. Use standard RCA jack connectors.
•
SCSI-In and SCSI-Out interface connectors: Use one connector to link your
PlexWriter to your SCSI interface board. Use the other to link your PlexWriter to
another SCSI peripheral in a chain; see pages 25 and 26. You may use either
connector for either purpose.
PlexWriter 40/12/40S Installation and Users Manual 7
Page 14
Section 1. Getting Started
About Software
In order to create CD-R and CD-RW discs you will need to have mastering, p acket
writing, or duplication software installed on your computer system. If you purchased
a retail kit from Plextor, you’ll get software packages that include this software.
For details on the various software packages for writing to CD-R or CD-RW, please
visit the web sites of the companies whose software you are interested in, refer to
their user’s manuals, or look at the help option within the software. A list of vario us
software packages that you can use with your Plextor drive can be found in the
Support/Compatibility section of www.plextor.com
.
Precautions
Like the rest of your computer system, your PlexWriter requires reasonable care in
its installation and use.
•
Do not put your computer monitor (or anything weighing more than 30 lbs.) on
top of a PlexWriter external drive.
•
Keep the area around your drive clean from dust, smoke, and other contaminants.
•
Do not allow moisture or liquids, including water or cleaning fluids, to touch the
drive. Thinner, benzene, or alcohol-based solvents can mar your drive’s surface.
•
Do not drop or jolt the drive.
•
Do not attempt to open the drive and service it yourself. Removin g the cover may
expose you to harmful electrical voltages or the laser beam. For your safe ty,
entrust service to experienced service personnel only.
•
Keep your CDs free of dirt or other contaminants, by storing them in jewel cases.
Use only industry-standard discs. Do not insert dirty, warped, poorly balanced, or
cracked discs into the drive.
•
Do not clean discs using a circular motion. Instead, use a radial motion: start at
the center of the disc and proceed to the outer edge.
CAUTION
recommend installing the drive so it is mounted vertically.
: Install your PlexWriter so it is oriented horizontally. Plextor does not
8
PlexWriter 40/12/40S Installation and Users Manual
Page 15
2. Installing Your PlexWriter
This chapter illustrates how to
physically install the PlexWriter
internal SCSI drive in your computer,
or how to attach the PlexWriter
external drive to the SCSI interface.
The steps you’ll need to do are as
follows:
1. Turn OFF your computer system.
2. Set the SCSI ID for your new
PlexWriter drive as necessary.
3. Set the PlexWriter’s termination.
(By default, termination is
enabled.)
4. If you have a new PCI SCSI
interface board, insert it into an
available PCI slot in your
computer. (Consult your board
vendor’s installation instructions.)
5. If you have an inter nal mod e l
Plextor drive, mount the drive in
an available bay inside the
computer system.
6. Make all necessary cabling
connections: SCSI cable, power
cable, and audio cable.
7. Turn your computer syste m ON.
The following pages give more
details for this procedure.
Quickstart SCSI
Installation—For
Experienced PC Users Only
If you’ve installed computer peripherals
before, you’re in luck with the
PlexWriter drive. Use this “quickstart”
installation designed to get you up and
running quickly.
Scenario 1: You purchased a Plextor
PlexWriter drive, the PlexWriter is your
only SCSI peripheral, and you have a
Windows operating system.
What to do: Purchase and install a
Plug-and-Play SCSI interface board
(with SCAM support). After it is
properly installed and configured, plug
in the PlexWriter, and go. Windows XP,
2000, Me, 98, or 95 will automatically
recognize the board and prompt you for
the SCSI interface board drivers. The
board’s manufacturer usually supplies
the latest available driver, either with
the board or on the manufacturer’s web
site. (In Windows NT you will need to
install the drivers manually through
Control Panel/SCSI Adapters.) After the
SCSI board drivers are installed and the
board is functioning correctly, the
drivers for your CD-RW drive will
automatically be installed by the
operating system.
NOTE
: Most newer SCSI controllers are
Plug-and-Play-compliant.
PlexWriter 40/12/40S Installation and Users Manual 9
Page 16
Section 2. Installing Your PlexWriter
Set SCSI Drive
Jumpers
Your PlexWriter SCSI drive needs to
be flexible enough to work with a
variety of available computer systems
and a number of other SCSI
peripherals. To provide this
flexibility, Plextor lets you specify
the drive’s settings before it is
installed.
On an internal SCSI drive, you
determine settings by the position of
jumpers on the jumper block at the
rear of the drive. On an external
drive, you determine settings by the
position of DIP switches and the
rotary dial on the rear panel of the
drive.
Your drive ships from our factory
with its jumpers, switches, and/or dial
set to work in the most commonly
found environment. You should leave
those switches and jumpers at their
factory settings, unless: 1) you plan to
use another SCSI peripheral (e.g.,
CD-ROM, hard disk, scanner) with
your computer system in addition to
your PlexWriter; or 2) you find it
necessary to change the block size
setting (most likely in an older UNIX
system).
Quickstart Installation
(Continued)
Scenario 2: You have a Plug-andPlay/SCAM SCSI interface board
installed already, the PlexWriter is your
only SCSI peripheral, and you have a
Windows operating system.
What to do: Plug in the PlexWriter,
and go. Windows will recognize the
drive and install the correct drivers
automatically.
Scenario 3: You have a SCSI interface
board installed that is not Plug-andPlay/SCAM-capable, and you have a
Windows operating system.
What to do: Set a unique SCSI ID
number for the PlexWriter, and make
sure all other peripherals, including the
SCSI adapter board, have their own
SCSI ID numbers. Set the termination
of each peripheral OFF; except set the
termination of the last peripheral
devices on each end of the SCSI chain
to ON.
Other scenarios, or if you have
problems: Better take a closer look at
this chapter.
Do I Have to Change My PlexWriter’s SCSI ID Number?
Your PlexWriter SCSI drive is shipped fro m the factory with its SCSI ID number set
to 4. The SCSI interface lets you chain several SCSI peripheral devices to a single
SCSI interface board, or to the SCSI port or SCSI adapter of an Apple computer,
with no loss of performance.
10
PlexWriter 40/12/40S Installation and Users Manual
Page 17
Section 2. Installing Your PlexWriter
NOTE:
The total cable length of all cables of a single SCSI chain of devices should
not exceed 3 meters. (Should not exceed 1.5 meters if more than four SCSI devices
are connected to the cable chain.) Shorter cable lengths are better, especially when
using multiple devices, or faster SCSI interfaces such as Ultra SCSI, Ultra Wide
SCSI, and other types. To achieve maximum performance if you are connecting more
than four SCSI devices, we recommend you balance the installation on two or more
SCSI adapter boards.
Each peripheral must have a unique SCSI ID number—your PlexWriter can have
any of 8 numbers (0-7). SCSI ID 7 is typically reserved by the SCSI interface board.
You probably don’t need to physically set the SCSI ID if:
•
Your PlexWriter drive is the only SCSI peripheral: In this case, don’t change
the SCSI ID. Leave it set to the original factory setting of 4.
•
You have a SCAM-compliant SCSI interfa ce board: Your Plextor drive is also
SCAM-compliant, so if you have Windows 95, 98, 2000, Me, or XP, you don’t
have to worry about setting SCSI ID numbers. (SCAM sets up SCSI addresses
automatically. If SCAM is enabled when you turn on your computer, the SCSI
interface board detects whether there is SCSI ID conflict between multiple
devices. Because your PlexWriter also supports SCAM, the drive automatically
resets its SCSI ID internally to avoid any conflict with other d evices.) SCAM
overrides any hardware settings.
You may have to physically set the SCSI ID if you have mor e than one SCSI
peripheral device and:
•
Your SCSI interface board is not SCAM-compliant: If you separately
purchased or already own a SCSI interface board, it may not be SCAMcompliant. In this case, you should determine the SCSI IDs of all peripheral
devices and change the PlexWriter’s ID to a unique number.
•
You don’t know if your SCSI interface boa r d is SCAM-compliant: In this
case, to be on the safe side, determine the SCSI IDs of all peripheral devices and
change the PlexWriter’s ID to a unique number.
•
You may have an older driver: Since SCAM was not a requirement when Plugand-Play specifications were written, original Windows 95 CDs may not include
a SCAM-compliant driver for your SCSI interface board. In this case, you should
determine the SCSI IDs of all peripheral devices and change the PlexWriter’s ID
to a unique number.
PlexWriter 40/12/40S Installation and Users Manual 11
Page 18
Section 2. Installing Your PlexWriter
Do I Have to Change My PlexWriter’s SCSI Termination
Setting?
The PlexWriter is shipped from the factory with its SCSI termination set ON. You
can leave the PlexWriter’s SCSI termination setting to ON if:
•
Your PlexWriter drive is the only SCSI peripheral: In this case, don’t change
the SCSI termination setting. Leave it set to the original factory setting of ON.
•
Your PlexWriter drive is the last peripheral in a chain: If you are using
multiple SCSI peripherals with your computer and the PlexWr iter is positioned as
the last peripheral in a chain, don’t change the PlexWriter’s termination setting.
Leave it set to ON. (However, make sure that any other peripheral devices on this
chain have termination OFF or disabled.)
NOTE
: The PlexWriter uses active termination.
You should change the PlexWriter’s SCSI termination setting to OFF if:
•
Your PlexWriter is in the middle of a chain: If you have multiple SCSI
Figure 5: What Termination Settings to Use
peripherals and the PlexWriter drive is not the last device in the chain, set its
SCSI termination to OFF. (In this case, remove, disable, or turn off termination
for all devices between the SCSI interface board and the last peripheral on the
opposite end of the chain. Set the termination of the last device in the chain to
on.)
12
PlexWriter 40/12/40S Installation and Users Manual
Page 19
Section 2. Installing Your PlexWriter
REMEMBER
enabled. If you have any SCSI devices chained after your PlexWriter, you must
disable or turn OFF the PlexWriter’s SCSI termination using the instructions later in
this chapter.
: Only the last SCSI peripheral in the chain should have termination
Termination Power
Some interface boards and peripherals have the ability to disable and enable
termination power. (This should not be confused with termination itself.)
Termination power must be provided by at least one device attached to your SCSI
interface board. Your Plextor drive automatically supplies termination power. Any
additional devices supplying termination po wer will not cause any prob lems.
Do I Have to Change Other PlexWriter SCSI Settings?
You probably won’t have to change any o f the other settings on your PlexWriter
SCSI drive’s switches or ju mpers. Use this table to help decide.
SCSI Switch
or Jumper
Setting
PRTY Parity setting. Leave this ON. The parity check provided by the
ON setting enhances the reliability of the SCSI bus. Set to OFF
only if your computer system, another peripheral on the SCSI
bus, or the SCSI interface board specifically requests that parity
be disabled.
TERM Termination setting. This enables or disables (turns ON or OFF)
SCSI termination. Factory setting is enabled (ON). See page 12
for an explanation of SCSI termination and to determine if you
need to change this setting.
TEST Leave this OFF. Set it ON for diagnostic testing only.
BLOCK Block size. Leave this OFF, unless you are working in a UNIX
environment and want to boot from your PlexWriter drive. If so,
set this jumper ON. Also set this ON for diagnostic testing only
SPDIF Sony/Phillips Digital Interface Format (digital audio out). If your
sound board supports SPDIF or Digital In, use an SPDIF cable
(not supplied) to connect it to these pins. (SPDIF is available
only on internal drives.)
Where to Set It
PlexWriter 40/12/40S Installation and Users Manual 13
Page 20
Section 2. Installing Your PlexWriter
Setting Jumpers on a PlexWriter Internal SCSI Drive
Use this procedure to set jumpers on your PlexWriter internal SCSI drive. (However,
if you already have a SCSI interface board installed, an internal PlexWriter is the
only SCSI peripheral you will use with your computer, and you do not need to
change any settings, skip now to “Install a PlexWriter Internal SCSI Drive” on page
18.)
Factory SCSI Jumper Setting s
Figure 6 shows the factory settings of the SCSI jumpers. The functions shown are
ON if the jumpers are installed and OFF if the jumpers are removed.
Figure 6: Factory Settings for Jumpers at the Rear of the Internal SCSI Drive
Changing SCSI Jumper Settings
To remove a jumper, pull it off with your fingers or a pair of needle-nose pliers.
Figure 7: Install Jumpers Across Vertical Pairs of Pins
CAUTION
14
PlexWriter 40/12/40S Installation and Users Manual
: Ensure power to the drive is OFF before installing or removing jumpers.
Page 21
Section 2. Installing Your PlexWriter
To add a jumper, push it onto the jumper pins. In addition to the three jumpers
already installed at the factory, extra jumpers are supplied with the PlexWriter drive.
CAUTION
jumpers lengthwise (horizontally). Doing so could result in damage to the drive.
: Install jumpers across each pin as shown (vertically). Do
not
install the
Changing the SCSI ID
If you already have another SCSI peripheral whose SCSI ID is set to 4, you must
change the SCSI ID number of either that peripheral or that of the PlexWriter drive.
(But see “Do I Have to Change My PlexWriter’s SCSI ID Number?” on page 10
before proceeding.)
The SCSI ID number of the internal PlexWriter drive is determined by the placement
of jumpers on Pins 1, 2, and 3. (To find the location of Pin 1, Pin 2, and Pin 3, refer
to the jumper diagram above.) To change the SCSI ID number, follow the chart
below.
Jumper Installed Across
SCSI ID Number Pin 1 Pin 2 Pin 3
0 OFF OFF OFF
1 ON OFF OFF
2 OFF ON OFF
3 ON ON OFF
4 (Factory setting) OFF OFF ON
5 ON OFF ON
6 OFF ON ON
7 ON ON ON
For example, the factory setting for SCSI ID 4 is made by installing a jumper across
Pin 3 of the jumper block, leaving Pin 1 and 2 uncovered. To set the SCSI ID at 3,
you would install a jumper across Pin 1, another jumper across Pin 2, leaving Pin 3
uncovered. To set the SCSI ID at 2, you would install a jumper across Pin 2, leaving
Pins 1 and 3 uncovered.
Changing the SCSI Termination Setting
The PlexWriter drive is shipped from the factory with its SC SI termination enabled
(ON).
If you have to disable (turn OFF) SCSI te rmination on your PlexWriter drive,
remove the jumper from Pin 5. Factory setting is enabled (ON). The following
illustration shows how to set the terminatio n setting for two typical cases. (See page
10 to see an explanation of SCSI termination and to determine if you need to change
the termination setting.)
PlexWriter 40/12/40S Installation and Users Manual 15
Page 22
Section 2. Installing Your PlexWriter
Figure 8: Using the Terminatio n Jumper
If your drive is already installed in your computer, be sure to turn off your computer
before removing (or reinstalling) the jumpers. We recommend that you retain the
jumpers so you can reinsert them onto the termination pins if you later need to turn
the drive’s SCSI termination ON.
If you have inte rnal SCSI peripherals only, then you should be using an internal
ribbon cable. In this case, all devices between the SCSI host adapter board and the
last peripheral on the opposite end of the ribbon cable should have their termination
removed, disabled, or turned off.
If you have both internal and external SCSI peripherals (both the internal and
external connectors of your host adapter board are used), then the termination of
your SCSI interface board should be removed, disabled or turned OFF. The last
peripheral on your internal cable and the last peripheral on your external SCSI chain
should retain their termination (have it set ON). All other SCSI peripherals
connected to the host adapter board should have their termination removed, disabled,
or turned off.
16
PlexWriter 40/12/40S Installation and Users Manual
Page 23
Section 2. Installing Your PlexWriter
Setting Switches on a PlexWriter External SCSI Drive
Use this procedure if you have a PlexWriter external SCSI drive. (However, if you
already have a SCSI board installed, an external PlexWriter is the only SCSI
peripheral you will use with your computer, and you do not need to change any
settings, skip now to “Install a PlexWriter External SCSI Dr ive” on page 24.)
Factory SCSI Switch Settings
A rear-panel rotary dial controls the SCSI ID setting of the external PlexWriter drive,
and other settings are controlled by DIP switches. Figure 9 shows the factory settings
of the rear-panel dial and switches.
Figure 9: Factory Settings for Dial and DIP Switches on External SCSI Drive
CAUTION
dial or the DIP switches.
: Turn the drive’s power OFF before changing the setting of the SCSI ID
Changing the SCSI ID
If you already have another SCSI peripheral whose SCSI ID is set to 4, you must
change the SCSI ID number of either that peripheral or that of the PlexWriter drive.
(But see “Do I Have to Change My PlexWriter’s SCSI ID Number?” on page 10
before proceeding.)
To change the SCSI ID number of the external PlexWriter drive, rotate the dial’s
arrow to a different SCSI ID number.
PlexWriter 40/12/40S Installation and Users Manual 17
Page 24
Section 2. Installing Your PlexWriter
Changing the SCSI Termination Setting
The PlexWriter external drive is shipped from the factory with its SCSI termination
enabled (ON). If you have to disable SCSI termination on yo ur PlexWriter drive, set
DIP switch 2 (TERM) to OFF.
If you are using external SCSI peripherals only, then you should be using an external
SCSI cable (or cables). In this case, all devices between the SCSI host adapter and
the last peripheral on the end of your SCSI chain, should have their termination
removed, disabled, or turned off.
If you have both internal and external SCSI peripherals (both the internal and
external connectors of your host adapter are used), then the termination of your SCSI
host adapter should be removed, disabled or turned OFF. The last peripheral on your
internal cable and the last peripheral on your external SCSI chain should retain their
termination (have it set ON). All other SCSI peripherals connected to the host
adapter should have their termination removed, disabled, or turned off.
NOTE:
Most newer SCSI interface boards have Auto Termination, so turning off its
termination is unnecessary. However, you still must specify termination ON or OFF on
the PlexWriter drive.
Install a PlexWriter Internal SCSI Drive
This section explains how to install a PlexWriter internal SC SI drive in a PC. Before
proceeding, double-check your SCSI ID number setting, SCSI termination setting,
and other jumper-controlled settings.
Record the Serial Number and TLA Code
Record the serial number and TLA code of your drive on the inside front cover of
this manual.
Mount the PlexWriter Internal SCSI Drive
You can mount your internal PlexWriter drive in any available bay. You must
remove the small panel that co vers the bay that you want to use.
CAUTION
recommend installing the drive so it is mounted vertically.
You must make a minimum of two cable connections to your PlexWriter. The two
cable connections that you must make are:
•
•
18
PlexWriter 40/12/40S Installation and Users Manual
: Install your PlexWriter so it is oriented horizontally. Plextor does not
SCSI cable
Power cable
Page 25
Section 2. Installing Your PlexWriter
There are also two optional cable connections:
•
A cable connection if you are using a sound board in your computer and plan to
connect the PlexWriter’s audio output to the audio connector on the sound board.
•
A cable connection if the sound board is equipped with SPDIF and you wish to
use the SPDIF digital audio output from your PlexWriter.
Choose a SCSI Ribbon Cable
The SCSI cable you will need is a standard 50-pin flat-ribbon cable. The cable may
have a termination on it. If the cable is supplied with a termination, remove the
termination jumper from the PlexWriter drive.
Figure 10: Internal SCSI Ribbon Cable
You may need to add or change a SCSI ribbon cable. Use these guidelines to help
decide on what internal SCSI cable you will use.
•
If the SCSI cable in your PC has a free connector: Use that SCSI cable.
•
If you purchased a SCSI interface board with a cable: Use the SCSI cable that
came with your SCSI interface board.
•
If the SCSI cable in your PC does not have a free connector: If you already
have one other SCSI peripheral (such as a hard disk) and your existing SCSI
cable is already full, remove that cable and replace it with a cable with more
connectors, such as the one shipped with the PlexWriter drive. If you need a
cable to connect more than two peripherals, you will need to purchase this cable.
Do You Need a Power Cable?
In most computers, you will find free power connectors in the computer that are
ready for your use. When you open the computer, check the cable running from your
power supply to your hard disk and see if it has extra connectors on it. If so, you can
plug one of these into the power connector found on the rear panel of the PlexWriter.
If you do not find any additional connectors (either because they were not supplied
or they are all in use), you will have to buy a “splitter” or a “Y-connector.” These
can also be found at most retail and mail-order computer stores.
PlexWriter 40/12/40S Installation and Users Manual 19
Page 26
Section 2. Installing Your PlexWriter
To mount the PlexWriter internal SCSI drive:
1. Make sure the power to your computer and any external peripherals is OFF and
your computer is UNPLUGGED from its power source.
2. If you haven’t already removed your computer’s cover, remove it now, following
the directions provided by your computer’s manufacturer. Typically, this
involves loo s ening or removing several screws on the b ack panel of your
computer and sliding off the cover.
Figure 11: Removing a Typical Computer’s Cover
3. Remove the cover panel from the bay that will hold the PlexWriter drive. To
remove the cover panel, pop it out by pressing outward lightly. (In some older
computers, you may have to remove screws that hold the panel in place.)
Figure 12: Removing the Cover Panel from a Bay
20
PlexWriter 40/12/40S Installation and Users Manual
Page 27
Section 2. Installing Your PlexWriter
4. Determine if you must install mounting rails on the sides of your drive. To do so,
insert the drive into the open bay. If the drive fits tightly with little or no
clearance on either side of the drive, you will not have to use mounting rails. The
drive can be mounted directly into your computer. Go to step 6.
NOTE:
Plextor does not provide rails. If you need rails, you can obtain them from the
computer manufacturer or from a computer supply retail or mail-order store. Most rail
kits are specific to a particular type of PC case. Check with the computer
manufacturer to make sure you get the correct rail kit.
5. If you must use mounting rails, fasten the rail s to the lower pair of holes as
shown in Figure 13. (In some instances, you may need to fasten the rails to the
upper set of holes.) After fastening the rails, check their positioning by sliding the
drive into the bay before you mount the drive or connect any cables.
Figure 13: Installing Mounting Rails (if Needed)
PlexWriter 40/12/40S Installation and Users Manual 21
Page 28
Section 2. Installing Your PlexWriter
6. Now plug in the SCSI cable.
If this is a new installation and your PlexWriter drive is the onl y SC SI
peripheral, plug one end of the SCSI cable into the SCSI connector on the
rear panel of the drive. (Do this before you insert the drive into your
computer.) Then thread the cable through the front of the open bay you plan
to use and back toward the SCSI interface board.
If you are adding the drive to an existing SCSI configuration, make sure the
drive’s termination jumper is removed and the SCSI ID is set to a unique
number. Then slide the drive into the drive bay, and plug a free connector on
the SCSI cable into the SCSI connector on the rear panel of the drive.
The drive should slide smoothly into the bay. If it does not, check for
obstructions in the bay and ensure the side rails (if needed) are attached properly.
CAUTION
Figure 14: Connecting the SCSI Ribbon Cable
: It is easy to accidentally plug your SCSI ribbon cable upside down into
both your drive and SCSI interface board. Be sure you match the red stripe along one
side of the SCSI cable to Pin 1 on the interface board and Pin 1 on the drive. Each
connector on the ribbon cable has a “key” in the middle. This key should fit into a slot
in the middle of each connector of the SCSI interface board, your PlexWriter, and any
other internal SCSI peripherals.
7. Double-check your work. You must ensure the side of the SCSI cable with the
red stripe is matched to Pin 1 on the interface board and on the drive.
8. Connect a power cable from the computer to the DC INPUT connector of the
PlexWriter drive. In most computers, you will find free power connectors that are
ready for your use. Check the cable running from your power supply to your hard
disk and see if it has extra connectors on it. If so, you can plug one of these into
the power connector found on the rear panel of the PlexWriter.
CAUTION
Do not force the connector. Doing so may damage the drive.
22
PlexWriter 40/12/40S Installation and Users Manual
: The power cable connector is keyed to fit in the drive’s power receptacle.
Page 29
Section 2. Installing Your PlexWriter
9. Connect the audio cable if you want to use a sound board in your system. This
cable runs from the four-pin AUDIO OUT connector on the rear panel of your
PlexWriter drive to your sound board. See page 27 for more information about
audio cables.
10. Connect the SPDIF cable if your sound board is equipped with SPDIF and you
wish to use the SPDIF digital audio output from your PlexWriter. T his cable r uns
from the right-most set of pins on the jumper panel to the sound board.
Figure 15 shows how the optional SPDIF cable is connected to the jumper panel.
(The SPDIF cable is not supplied by Plextor.)
Figure 15: Installing the Optional SPDIF Cable
11. Before completing the installation, check your cable connections against
Figure 16.
PlexWriter 40/12/40S Installation and Users Manual 23
Page 30
Section 2. Installing Your PlexWriter
Figure 16: Power, SCSI, and Optional Connections
for an Internal PlexWrite r Drive
12. If you did not use mounting rails, mount the PlexWriter driv e in the computer
using the four screws that were supplied with your drive. Use only these screws.
CAUTION:
supplied by Plextor. You may damage the drive if you insert screws that are too long.
Do not mount your drive in your computer using screws other than those
Install a PlexWriter External SCSI Drive
To install a PlexWriter external SCSI drive, decide which cables you use, and
whether you need to change the DIP switch and SCSI ID selector dial on your
PlexWriter. Also check whether you need to change settings such as termination on
other SCSI peripheral devices.
CAUTION
performance in a vertical position.
Before proceeding, double-check your SCSI number setting, SCSI termination
setting, and other switch-controlled settings.
: Install your PlexWriter horizontally. Plextor does not guarantee the drive’s
24
PlexWriter 40/12/40S Installation and Users Manual
Page 31
Section 2. Installing Your PlexWriter
Connect a Single External SCSI Drive
If you are installing a single PlexWriter external SCSI drive, connect it as shown in
Figure 17.
Figure 17: Connecting a Single PlexWriter External SCSI Drive to a PC
PlexWriter 40/12/40S Installation and Users Manual 25
Page 32
Section 2. Installing Your PlexWriter
Connect Multiple External SCSI Drives
If you are installing more than one PlexWriter external SCSI drive (or one
PlexWriter and other external SCSI peripherals), connect them as shown in
Figure 18.
Figure 18: Connecting Multiple External SCSI Drives or Peripherals
NOTE
: Performance of SCSI devices may suffer if the total cable length in the SCSI
chain exceeds 3 meters. (Assume cabling in the external case equals about 20 cm
when adding up total cable length.) Quality of cabling is also important. Use shielded
cables when possible. Also, keep cable length as short as possible, especially when
using faster interfaces such as Ultra SCSI, Ultra Wide SCSI, and others.
26
PlexWriter 40/12/40S Installation and Users Manual
Page 33
Section 2. Installing Your PlexWriter
Starting an External PlexWriter
After connecting an external PlexWriter, start the PlexWriter and the computer in
this order:
1. First turn the PlexWriter power switch ON.
2. Then turn the computer power ON.
Using Sound Boards and Audio Cables
Whichever category your sound board falls into, you will find that the best source of
information about installing the sound board in your co mputer is the board’s manual.
Once you have successfully installed the sound board in your computer, you can
continue below for a description of the different cable connections that need to be
made.
NOTE:
board to control your PlexWriter. You may not be able to utilize high speed recording
(40X) due to the performance of the board.
If you need audio cables, you will have to purchase them. Refer to the table below.
Plextor strongly suggests you not use the SCSI connection on your sound
Your PlexWriter Kit Audio Cables You May
Need to Purchase
Internal Drive MPC-compliant audio
cable
Sound Blaster-
compatible audio cable
Sony/Philips digital
interface (SPDIF)
External Drive RCA audio cable Connect one end to the
How to Connect Audio
Connect to MPC audio
source, and to AUDIO OUT
connector at the rear of the
PlexWriter.
Connect to Sound Blastercompatible audio board
and to AUDIO OUT
connector at the rear of the
PlexWriter (Figure 16).
If your sound board
supports SPDIF or Digital
In, use an SPDIF cable to
connect it to these pins.
sound board Line In
connectors or to an audio
amplifier, and the other end
to the AUDIO OUT
connectors at the rear of
the PlexWriter (Figure 19).
PlexWriter 40/12/40S Installation and Users Manual 27
Page 34
Section 2. Installing Your PlexWriter
Figure 19: Connecting Audio Cables to a PlexWriter External SCSI Drive
What Else Do I Need?
Plextor SCSI CD-R/RW drives are supported as read-only devices by the embedded
Windows operating system drivers. This means you should be able to play CDs right
away, without installing any additional dr ivers.
Recording Software
In order to use your Plextor drive to record on CD-R or CD-RW media, you’ll need
to have mastering, packet writing, or duplication software installed on your computer
system. If you purchased a retail kit from Plextor, you’ll get software packages that
include this software. A list of various software packages that you can use with your
Plextor drive can be found in the Support/Compatibility section of
www.plextor.com.
SCSI Adapter Drivers
You will need drivers that let your SCSI interface work with the Windows 95/98,
Me, 2000, or XP operating system. If you have installed a SCSI interface board,
these drivers should be supplied by the board manufacturer. If the SCSI interface is
on the computer’s motherboard, the drivers are supplied by the motherboard vendor.
To install SCSI adapter drivers in Windows oper a ting systems, check your SCSI
adapter board installation instructions. If your SCSI adapter is designed into your PC
motherboard, contact your motherboard vendor for driver installation instr uctions.
28
PlexWriter 40/12/40S Installation and Users Manual
Page 35
3. Using Your PlexWriter
This chapter explains how to use your PlexWriter drive and how to load, handle and
care for your CDs.
CAUTION
recommend installing the drive where it is mounted vertically.
: Install your PlexWriter so it is oriented horizontally. Plextor does not
What Media to Use
Use the right media! Your PlexWriter drive's capabilities change depending on
which type of compact disc you use. It currently supports these types:
•
CD-ROM: You can immediately play or read prerecorded discs, such as audio
CDs and data discs.
•
CD-R: Recordable CD. You can record on these discs, but only once. You can
also read them.
•
CD-RW: High speed ReWritable CD. These discs support recording and rerecording (up to 1,000 times). You can also read them.
Achieving Maximum Rated Writing Speed
To achieve 40X CD-R writing speed you must use certified 40X media; and to
achieve 12X RW writing speed you must use high speed RW media. See
“Recommended Media” on page 41 for a list of Plextor-approved media at the time
this manual was printed, and see the Plextor web site at http:// www.plextor.com
an updated list.
You can write to high speed RW discs only on drives that support this new media.
Drives that are capable of writing to high speed RW media, such as the PlexWriter
40/12/40S, are identified by a “Compact Disc ReWritable High Speed” logo.
for
Writing at Lower Speeds
The PlexWriter can write at lower speeds than maximum. (For example, to achieve
the best audio quality, the PlexWriter’s VariRec feature enables the drive to write at
1X or 4X speed.) Because 40X media will not work at these lower speeds, you will
need to purchase CD-R media that is rated for lower speeds. See “Recommended
Media” on page 41 for a list of Plextor-approved media at the time this manual was
printed, and see the Plextor web site at http://www.plextor.com
PlexWriter 40/12/40S Installation and Users Manual 29
for an updated list.
Page 36
Section 3. Using Your PlexWriter
Tray Loading and Operation
To load and unload the tray:
1. While the PlexWriter drive is powered up, push the stop/eject button on the front
panel. The tray drawer slides out in 3–4 seconds.
Figure 20: Loading the Tray
2. Lay a blank CD in the depression in the tray, label side up. The disc should lie
flat in the tray.
3. Press the stop/eject button again and the tray will slide shut within seconds.
NOTE
: Always use the stop/eject button to close the tray in a smooth and secure
manner. Closing the tray by pressing the front of the drawer by hand is not
recommended and risks damage or premature wearing of the mechanism and your
CDs.
Handling CD Media
Take care when handling blank CD-R and CD-RW media. Dust, scratches, and
fingerprints on either side of the disc can cause write errors during recording. When
picking up or holding blank media you can either place your fingers along the outer
edge of the disc, or place one finger through the center hole and one finger on the
outer edge. Once you have finished creating a disc, label it by writing on the top
using per manent ink.
CAUTION
conforms to the ASTM D-4236 standard. Some permanent markers will damage the
media. Also, do not press too hard when writing on the disc.
NOTE:
weight of the label may unbalance the disc and cause write errors during recording or
read errors during reading.
: We recommend using a “non-toxic” marker, such as a Sharpie pen, that
We do not recommend placing self-sticking CD-R labels on the disc. The
30
PlexWriter 40/12/40S Installation and Users Manual
Page 37
Section 3. Using Your PlexWriter
Cleaning Discs
For proper read and write performance, your CD-R, CD-RW, and CD-ROM discs
must be clean. Trying to record on a dirty disc may result in a failed session and ruin
the disc.
To clean the disc, wipe the disc using a clean, soft cotton cloth to remove surface dirt
such as fingerprints. Use a straight-line motion, wiping fro m the center out. Do not
wipe the disc in a circular motion.
Figure 21: Wipe the Disc from the Center Outward
HINT:
Keep your frequently used discs in jewel cases at all times to prevent them
from becoming dirty or damaged.
Using the Writing Speed Indicators
When you are writing to a CD or CD-RW disc, the color and blink rate of the frontpanel WRITE L and WRITE H indicators show the speed of writing, as follows:
Writing Speed WRITE L Indicator WRITE H Indicator
CD-R at 40X, 32X OFF Amber ON:
40-ms blink interval: 40X CD-R
80-ms blink interval: 32X CD-R
CD-R at 1X-24X Amber ON OFF
CD-RW at 12X OFF Amber ON:
80-ms blink interval
CD-R at 10X, 4X Amber ON OFF
If the ON/READ indicator is on green during a write operation, and WRITE L and
WRITE H are off, BURN-Proof is active.
PlexWriter 40/12/40S Installation and Users Manual 31
Page 38
Section 3. Using Your PlexWriter
Advantages of BURN-Proof Technology
The PlexWriter 40/12/40S incorporates BURN-Proof, which guarantees that you can
write discs at high speed, and still use your computer for o ther tasks while you’re
writing.
To prevent the interruption of data during writing, every CD-R/RW drive has a
buffer, a memory chip that acts as a kind of “holding area.” (Typically, the buffer
size is 2 MB or 4 MB.) However, this buffer can be emptied quickly when you write
at high speeds, or if you use other applications (like surfing the Internet or playing
games or watching movies) while writing.
BURN-Proof compensates for any interruption in data flow to the disc. It
“remembers” where writing stopped on the disc when the data flow was interrupted,
then restarts writing in the same place once the data is available again. BURN-Proof
in your PlexWriter 40/12/40S means you can safely use your computer for other
things while you’re writing to a CD-R or CD-RW disc. It lets you multitask freely
and easily, and lets you successfully create CDs on the first attempt.
Advantages of VariRec Technolog y
This drive is equipped with VariRec (Variable Recording) technology, a feature
offered by Plextor that allows you to manually adjust the drive's laser power during
the audio recording process.
NOTE
: In order for you to actually perform the adjustment, VariRec must be
supported by the recording software you’re using.
Being able to adjust the laser power during the recording process can have some
definite advantages. For instance, depending on the capabilities of your specific
audio equipment, you may be ab l e to change the sound q uality of your recordings to
suit the equipment. Or you may be able to correct compatibility problems that occur
when playing discs on certain audio players.
How the Default VariRec Setting Is Determined
In most cases you don’t have to worr y about settin g VariRec. The setting is 0 (zero)
by default, and this usually works best. This default setting is d e ter mined by a
combination of steps:
1. First, we test many types of CD-R and CD-RW media in our factory to determine
the best write strategy (laser power and other factors) for that media.
2. We include a table of the tested media and their write strategy in your dr ive’s
firmware. (This table is updated when you update your drive by downloading
new firmware from the Plextor web site.)
32
PlexWriter 40/12/40S Installation and Users Manual
Page 39
Section 3. Using Your PlexWriter
3. When you insert a recordable disc into your drive, Plextor’s PoweRec technology
automatically identifies the manufacturer, model, and special features of the
media, then adjusts the laser power and writing speed so they’re at the optimum
settings for that d isc.
4. The drive uses OPC (Optimum Power Control) to further fine-tune the laser
power setting to the specific disc that is in your drive.
5. The combined values of the pre-defined write strategies, along with the OPC test
results, create the default VariRec setting of zero.
Changing the VariRec Setting
VariRec lets you increase or decrease the laser power by up to 2 degrees in either the
positive or negative direction from this default. You can change the laser power to do
comparison testing with your CD player (home, auto, or CD-ROM drives) to find the
power setting that best suits you.
Changing the laser power changes the characteristics of the audio being written. You
can hear these changes during audio playback, although what you hear will depend
on speaker quality, audio settings, and environment.
When You Write with VariRec
VariRec writes in either Track-at-Once (TAO) or Disc-at-Once (DAO) mode. It
writes CD-DA (digital audio) on CD-R media at 1X or 4X speed, rather than at the
full speed of the drive. For this reason, audio recording using VariRec will take
significantly longer than a standard audio recording.
PlexWriter 40/12/40S Installation and Users Manual 33
Page 40
Section 3. Using Your PlexWriter
This page intentionally left blank.
34
PlexWriter 40/12/40S Installation and Users Manual
Page 41
4. Maintenance and Troubleshooting
This chapter explains maintenance and troubleshooting procedures for your
PlexWriter drive.
With proper maintenance, you can prevent problems. If problems arise, you can
often solve many simple problems on your own, rather than wait for assistance from
a Plextor representative.
Upgrading Firmware
Plextor creates firmware revisions to meet the peculiar needs of large computer
manufacturers. It is rare that these will impact the performance or operation of your
PlexWriter drive. However, we advise that our customers always update drives with
the latest available firmware. Before troubleshooting a possib le p r oblem with your
drive please make sure to visit our web site at www.plextor.com
the latest firmware.
To obtain new firmware for your PlexWriter drive:
1. Go to the Plextor web site at www.plextor.com
2. Look for firmware upgrades in the Support area, on the Downloads page. There
is a description of the latest firmware revision and its intended use.
3. Download the firmware to your computer.
To upgrade firmware:
1. Run the executable file that you downloaded from Plextor’s web site.
2. Accept all defaults by continuing to click on the “Next” button until you see the
message:
Firmware update has completed.
.
to check i f you have
Troubleshooting
If you have problems during or right after installation of your PlexWriter drive, visit
the Plextor web site to find tips to help find the problem.
PlexWriter 40/12/40S Installation and Users Manual 35
Page 42
Section 4: Maintenance and Troubleshooting
Using the Self-Test Diagnostics
The PlexWriter contains a set of self-test diagnostics that can help isolate trouble and
determine if a problem is in the drive or elsewhere. This tests three functions of the
drive: write, random access, and verify.
Performing the Self-Test on an Internal Drive
This procedure details how to perform the self-test procedure on an internal drive.
NOTE
: Using the self-test diagnostics on an internal drive requires opening the
computer and removing the SCSI cable from the drive, then replacing the cable at the
end of the test. If you previously installed the PlexWriter in your computer, you should
have no fear of the simple procedures that are required. However, if you’re are not
comfortable with opening your PC or Macintosh and disconnecting cables, you may
want to let someone with more experience handle this aspect of troubleshooting for
you.
What you’ll need:
To perform the test you’ll need:
•
Tools to remove the computer’s cover
•
The spare jumpers shipped with your drive
•
A blank piece of Plextor-recommended CD-R media for the CD write/read test.
(See “Recommended Media” on page 41, or visit our web site.)
To perform the CD write/read test:
1. Turn the computer’s power OFF, unplug it from its power source, and open the
computer to gain access to the rear of the PlexWriter drive. Typically, this
involves loo s ening or removing several screws on the b ack panel of your
computer and sliding off the cover.
CAUTION
yourself by wearing an anti-static wristband. This will help prevent static damage to
your computer system.
2. You should be able to see the back of the PlexWriter drive connected to the SCSI
NOTE
steps.
3. Hold the SCSI cable at or near the base of its connection to the PlexWriter.
: Before you attempt to open your computer be sure to properly ground
cable, power connector, and, optionally, an analog sound cable and/or an SPDIF
cable.
: You may have to remove the drive from the computer to perform the next two
Carefully remove the SCSI cable from the PlexWriter by pulling the cable gently
rearward.
36
PlexWriter 40/12/40S Installation and Users Manual
Page 43
Section 4: Maintenance and Troubleshooting
4. Note the position of the jumpers at the rear of the PlexWriter. Write do wn the
jumper positions. (You’ll need to add test jumpers for the test, but you’ll want to
remove these jumpers after the test and leave the PlexWriter’s setup the way you
found it.)
5. Now install jumpers as follows:
Install one of the spare jumpers across the “TEST” jumper pins.
Install another spare jumper across the “BLOCK SIZE” jumper pins.
If there is a jumper across the “TERM” pins, remove it for this test.
Figure 22: For Self-Test, Add the TEST and BLOCK SIZE Jumpers, and Make
Sure There Is No Jumper Across the TERM Pins
6. If you removed the drive for access to the SCSI cable and mode jumpers, slide it
back into the computer.
7. Replace the computer’s cover.
CAUTION
dangerous to the computer’s components and also to you. Be aware of the danger of
electric shock and do not touch any components inside the computer.
: Turning on the computer power without first replacing the cover can be
8. While pressing the stop/eject button on the PlexWriter, turn the computer power
on. The tray ejects, the ON indicator is illuminated, and the WRITE H and
WRITE L indicators blink alternately.
9. Insert a blank Plextor-recommended CD-R disc and press the stop/eject button to
load the disc. Be sure to use only CD-R media of the type recommended by
Plextor.
If the DISC indicator blinks amber three times, the loaded disc is not a blank
CD-R disc. Remove the disc and insert a blank, Plextor-approved CD-R disc.
PlexWriter 40/12/40S Installation and Users Manual 37
Page 44
Section 4: Maintenance and Troubleshooting
10. The drive begins the diagnostic routine, and the WRITE H and WRITE L
indicators alternately blink. The diagnostic routine takes approximately nine
minutes. Upon completion of the diagnostic, you see the results:
Disc ejects: If there was no problem, the disc is ejected automatically.
Discard the disc. It cannot be reused.
Blinking WRITE H indicator LED: No blank disc.
DISC indicator LED blinks once: Write or read error.
DISC indicator LED blinks twice: Initialization error.
11. If the disc was not ejected automatically, press the stop/eject button to eject the
disc.
12. Turn off the computer power.
13. Remove the spare jumpers you installed in step 5 above, and replace the jumper
across the TERM pins (if you removed it for the test).
14. Reconnect the SCSI cable to the PlexWriter drive. If you removed the drive to
gain access to the cable or jumpers, replace the drive in the computer. Then
replace the computer cover.
Performing the Self-Test on an External Drive
This procedure details how to perform a self-test procedure on an external drive.
What you’ll need:
To perform the test you’ll need:
•
A blank piece of Plextor-recommended CD-R media for the CD write/read test.
(See “Recommended Media” on page 41, or visit our web site.)
To perform the CD write/read test:
1. Turn the PlexWriter power switch OFF.
2. Turn the computer power OFF.
3. Carefully unplug the SCSI cable from the PlexWriter by pulling the cable gently
rearward.
4. Note the position of the DIP switches at the rear of the PlexWriter. Write down
the switch positions. (You’ll need to change these switches for the test, but you’ll
want to return to the same configuration after the test and leave the PlexWriter’s
setup the way you found it.)
38
PlexWriter 40/12/40S Installation and Users Manual
Page 45
Section 4: Maintenance and Troubleshooting
5. Now set the DIP switches as follows:
Set the “TEST” switch to ON.
Set the “BLOCK” switch to ON.
Set the “TERM” switch to OFF.
Don’t change the settings of the rotary switch or other DIP switches.
Figure 23: For Self-Test, Set the TEST and BLOCK Switches to ON, and Set the
TERM Switch to OFF
6. While pressing the stop/eject button on the PlexWriter, turn its p ower ON. The
tray ejects, the ON indicator is illuminated, and the WRITE H and WRITE L
indicators blink alternately.
7. Insert a blank Plextor-recommended CD-R disc and press the stop/eject button to
load the disc. Be sure to use only CD-R media of the type recommended by
Plextor.
If the DISC indicator blinks amber three times, the loaded disc is not a blank
CD-R disc. Remove the disc and insert a blank, Plextor-approved CD-R disc.
8. The drive begins the diagnostic routine, and the WRITE H and WRITE L
indicators alternately blink. The diagnostic routine takes approximately nine
minutes. Upon completion of the diagnostic, you see the results:
Disc ejects: If there was no problem, the disc is ejected automatically.
Discard the disc. It cannot be reused.
Blinking WRITE H indicator LED: No blank disc.
DISC indicator LED blinks once: Write or read error.
DISC indicator LED blinks twice: Initialization error.
9. If the disc was not ejected automatically, press the stop/eject button to eject the
disc.
10. Turn OFF the PlexWriter power.
11. Return the DIP switches on the PlexWriter to the positions you noted in step 4
above.
12. Reconnect the SCSI cable to the PlexWriter drive.
PlexWriter 40/12/40S Installation and Users Manual 39
Page 46
Section 4: Maintenance and Troubleshooting
After the Self-Test
If you discover a problem with the PlexWriter drive, do not attempt to service the
drive yourself. Contact us to get an RMA number and take st eps to return the drive to
Plextor. See page 48 for details.
40
PlexWriter 40/12/40S Installation and Users Manual
Page 47
Appendix A: PlexWriter Specifications
Minimum Syst em Requirements
Computer Pentium II 300 MHz CPU or faster.
Minimum RAM 64 MB
Hard Disk Size 1 GB of free space to write to a CD in image mode
Interface Ultra SCSI-3
Operating System Windows XP, Me, 2000, 98, 95; Mac OS
Recommended Media
CD-R: 40X To ensure 40X write speed, use certified 40X media
CD-R: 32X Ricoh, Maxell, Taiyo Yuden,
CD-R: 24X
CD-R: 20X-4X Ricoh, Mitsui Chemicals, Mitsubishi Chemical (Verbatim),
CD-R: 1X Ricoh, Maxell, Taiyo Yuden, Mitsubishi Chemical
CD-RW: 12X Ricoh, Mitsubishi Chemical (Verbatim)
CD-RW: 10X-4X Ricoh, Mitsubishi Chemical (Verbatim)
Supported Media
Supported Media,
Stamped CD
Supported Media, CD-R Orange Book Pt II-compliant discs (Type 74, Type 80)
available from Taiyo Yuden, Mitsubishi Chemical
(Verbatim), or Maxell. (With PoweRec, some discs may
be recorded at 16X because of lower quality media.)
NOTE
: For the latest updated list of certified 40X media,
see Plextor’s web site at: http://www.plextor.com
Mitsubishi Chemical (Verbatim)
Ricoh, Mitsui Chemicals, Maxell, Taiyo Yuden,
Mitsubishi Chemical (Verbatim)
TDK, Taiyo Yuden, Maxell
(Verbatim)
(All CD-RW media are rewritable up to 1,000 times.)
Red, Yellow Book-compliant discs
Supported Media,
CD-RW
Supported Media Size 12 cm
Orange Book Pt III-compliant discs
PlexWriter 40/12/40S Installation and Users Manual 41
Page 48
Appendix A: PlexWriter Specifications
Usable Formats
Logical CD Read/Write CD-DA, CD-Extra, CD-ROM Mode-1, Mix CD, CD-ROM
XA, Photo-CD, Video-CD, CD-I, Multisession, CD TEXT,
CD+G, UDF, MRW
Write Methods TAO, DAO, Packet Write (variable and fixed), Multi-
session, SAO
Performance Specifications
Read Speed, CD Speed Mode-1 Mode-2 CD-DA
17-40X Stamp,R,RW Stamp,R,RW Stamp,R
14-32X Stamp,R,RW Stamp,R,RW Stamp,R,RW
10-24X Stamp,R,RW Stamp,R,RW Stamp,R,RW
8X CLV Stamp,R,RW Stamp,R,RW Stamp,R,RW
4X CLV Stamp,R,RW Stamp,R,RW Stamp,R,RW
NOTE
Write Speed, CD-R
(Data)
: “Stamp” indicates commercially pressed “silver”
discs
40X Z-CLV (20-24-32-40X)
32X Z-CLV (20-24-32X)
24X Z-CLV (20-24X)
20X CLV, 16X CLV, 8X CLV, 4X CLV, 1X CLV
Write Speed, CD-R
(CD-DA)
40X Z-CLV
32X Z-CLV
24X Z-CLV (20-24X)
20X CLV, 16X CLV, 8X CLV, 4X CLV, 1X CLV
(VariRec operates at 1X and 4X)
Write Speed, CD-RW 12X CLV, 10X CLV, 4X CLV
High speed media: 4X, 10X, 12X
Normal speed media: 4X
Initialization Time < 13 sec. (typical), < 15 sec. (max.)
Time measured from power on until disc is available to
read
Access Time <120 ms (typical)
Time measured from start command until bus free (no
disconnect)
Sleep Mode Entered after 2 minutes of no access to drive
Wake Mode < 5 sec. (max.) to start drive after sleep
Other Features
Data Buffer 4 MB
Error Rate CD-ROM Mode 1: 1 Block/10
CD-ROM Mode 2: 1 Block/109 Bits
12
Bits
42
PlexWriter 40/12/40S Installation and Users Manual
Page 49
Appendix A: PlexWriter Specifications
Front Panel
Eject Methods Stop/eject button; manual emergency eject; software
eject
LED Indicators DISC indicator:
Green: Disc load
ON/READ indicator:
Green: Power on
Blinking green: Data access.
Green during writing: BURN-Proof is active
WRITE L indicator:
Amber: Recording CD-R discs at 1X-24X speed, or
CD-RW at 4X-10X speed
WRITE H indicator:
Amber: Recording CD-R discs at 32X or 40X speed, or
CD-RW at 12X speed
Writing Speed L H
CD-R at 40X, 32X OFF ON
CD-R at 1~24X ON OFF
CD-RW at 12X OFF ON
CD-RW at 10X/4X ON OFF
Blink interval:
40ms—CD-R recording at 40X
80ms—CD-R recording at 32X or
CD-RW recording at 12X
Disc Loading Auto loading, auto eject
Headphone Jack Stereo mini-jack, 0.8V +/- 0.3V at 32 ohms
Headphone Volume
Control
Wheel knob
Power Switch (External drive only.)
PlexWriter 40/12/40S Installation and Users Manual 43
Page 50
Appendix A: PlexWriter Specifications
Rear Panel—Internal Drive
Power Supply Input Voltage: AC 100-240V (50/60Hz)
AC 100V: Typically 15W during writing, 15W during
reading. Peak (OPC and spinup) 27W.
AC 240V: Typically 16W during writing, 16W during
reading. Peak (OPC and spinup) 28W.
Interface Connector SCSI bus, 50-pin flat ribbon type
Audio Connector Stereo analog output, Molex connector
Output 0.55V +/-0.1V at 10k ohms
Jumper Switches SCSI ID, parity, termination, test, block size,
SPDIF (digital audio output for input to SPDIF or Digital-
In input)
Rear Panel—External Drive
Power Switch Tumbler type; 3A, 250V
Power Supply Input voltage: AC 100-240V (50/60Hz)
Power requirements:
AC 100V: Typically 14W during writing, 14W during
reading. Peak (OPC and spinup) 27W.
AC 240V: Typically 16W during writing, 16W during
reading. Peak (OPC and spinup) 28W.
Interface Connector SCSI bus, 50-pin D-sub half-pitch cable
Audio Connector Stereo analog output, RCA connector
Output 0.55V +/-0.1V at 10k ohms
DIP Switches Parity, termination, test, block size
Rotary Switch SCSI ID
44
PlexWriter 40/12/40S Installation and Users Manual
Page 51
Appendix A: PlexWriter Specifications
Host Interface
Type ANSI X3.131; 1994SCSI-compliant
Data connector Internal drive: Connector for 50-pin flat cable. Maximum
total cable length should be less than 3m for daisy chain
(1.5m if more than 4 devices are attached)
External drive: 50-pin high density connector. Maximum
total cable length should be less than 3m for daisy chain
(1.5m if more than 4 devices are attached)
Burst Mode Sync. 20MB/s
Async. 5MB/s
Signal Line Low input voltage: > 0.8 V
High input voltage: < 2.0V
Terminator Active type
Internal drive termination: Enabled by installing a jumper
across TERM connectors on rear panel
External drive termination: Enabled by moving TERM
DIP switch to the “on” position
SCAM SCAM Level-1
SCSI command Refer to Plextor SCSI command manual
Inquiry string PLEXTOR sp CD-R sp sp sp PX-W4012S
(where “sp” equals one space)
Environmental Conditions
Operating Temperature 5 to 35 degrees Celsius
Performance Guarantee
Temperature
Operating Humidity
Storage Temperature –40 to 60 degrees Celsius
5 to 35 degrees Celsius
20% to 80% (non-condensing)
Storage Humidity
20% to 95% (non-condensing)
PlexWriter 40/12/40S Installation and Users Manual 45
Page 52
Appendix A: PlexWriter Specifications
Dimensions and Weight
Dimensions (W/H/D)
(excluding front panel)
Internal SCSI drive: 5.75" x 1.63" x 7.95"
146 mm x 41.3 mm x 202 mm
External SCSI drive: 7.13” x 2.34” x 12.15”
(181 mm x 59.4 mm x 308.5 mm)
Weight Internal SCSI drive: 2.5 lbs. (1.2 kg)
External SCSI Drive: 5.75 lbs. (2.61 kg)
Reliability
MTBF 60,000 hours
(Power on duty cycle 15%, 8 hours/day
Read duty 70%, write duty 30%)
Tray Loading 100,000 Load/Unload Cycles
Safety Standards
Country/ Region Type Agency Standard
USA Safety UL UL 1950
Laser FDA FDA 21 CFR
EMC FCC FCC 15J-Class B
Canada Safety CSA CSA 22.2 No. 950
Safety UL UL 1950 (C-UL mark)
Europe Safety CE IEC60825
Safety CE IEC60950
Laser CE IEC 60825-1
EMC CE EN55024, EN55022
Taiwan EMC BSMI CNS13438 Class B
Korea EMC MIC
Australia/NZ EMC C-Tick 3548 (CISPR 22)
Safety TUV IEC 60950
46
PlexWriter 40/12/40S Installation and Users Manual
Page 53
Appendix B: Technical Support
Store Plextor’s e-mail, web site, phone, and fax numbers in a convenient location.
Keep your drive’s serial number and a copy of your sales receipt handy as well.
If you experience a problem while installing or operating your PlexWriter drive,
please refer first to the relevant sections of this manual regard ing se tup and
installation (Chapters 1–3). If you do not uncover the solution there, please refer next
to the maintenance and troubleshooting chapter that begins on page 35. You may
also wish to refer to the Frequently Asked Questions (FAQ) section of our web site
to assist you in troubleshooting the problem on your own.
NOTE
: We encourage you to go the Plextor web site (www.plextor.com) before
attempting to contact Technical Support. The answers to the most common questions
callers ask can be found quickly in the support area. Select PlexHelper for online
troubleshooting or FAQs for common questions.
If you have not been successful in your quest, our Technical Support Department
will help you solve problems that relate specifically to your PlexWriter drive. In
many cases, a problem that appears to be caused by your PlexWriter actually
originates in another part of your computer. In such instances, our technical support
staff will try to help you identify the part at fault and will refer you to the
manufacturer of that part for further assistance.
How to Contact Plextor Technical Support
There are several ways for you to contact Plextor’s Technical Support Department:
•
Visit our web site (www.plextor.com
Questions.
•
Send us e-mail at support@plextor.com
hours during which you can be reached. Be as detailed as possible in describing
your problem. Please include system configuration, hardware and software, as
well as versions of drivers used.
•
Call 800-886-3935 and select the tech support option.
) for answers to Frequently Asked
. Include your telephone number and the
PlexWriter 40/12/40S Installation and Users Manual
47
Page 54
Appendix B: Technical Support
Before You E-mail/Log On/FAX/Call
Please gather as much of the following information as possible before contacting us.
•
The serial number and TLA number of your PlexWriter. Your serial number can
be found both on the warranty card that accompanied the drive and on a label on
the drive itself. The TLA number appears both on the drive label and on a sticker
at the rear of internal drives.
•
The latest version of firmware you loaded onto the drive, if applicable.
•
The version of the Windows or Ma cintosh operating system you are using.
•
The brand name and model number of your computer (e.g., Dell 466/NP,
Hewlett-Packard Pavilion 752n, Apple Macintosh G4, etc.).
•
The type of VGA, Super VGA, or other graphics board you use.
•
Brand name and model number of any other peripherals you have installed or
connected to your computer (e.g., CD-ROM, scanner, fax board, network board).
•
For PlexWriter SCSI drives, the name and model number of your SCSI interface
board (e.g., Adaptec AHA-2940, Advansys ABP-930UA).
•
For PlexWriter SCSI drives, the version of the software device drivers, if any,
that came with your SCSI interface board. (This typically is found on the label of
the floppy disk or CD-ROM that contains the device drivers.)
Returns
In the unlikely event that you need to return a drive to Plextor, you need an RMA
(Returned Materials Authorization) number. You need this number before any
Plextor drive can be returned for repair or replacement. Here’s how you get an RMA
number and return your drive:
1. Contact Plextor Technical Support. You will receive assistance in
troubleshooting your system. If the drive is determined to be defective, you will
receive a Tech Support Ticket Number.
2. Locate the RMA request form at:
https://www.plextor.com/english/support/rma_request_form.htm
form, providing the Technical Support Ticket number and details of the drive
failure. After completing the form, click the Submit button.
IMPORTANT NOTE
Ticket Number.
: The RMA form will not be processed without the Tech Support
48
PlexWriter 40/12/40S Installation and Users Manual
. Complete the
Page 55
Appendix B: Technical Support
3. Plextor then returns the RMA form to you via e-mail, with the RMA number and
shipping information included.
4. When you receive the RMA number, pack the Plextor drive securely in a box,
and include the RMA form as a packing slip.
5. Write the RMA number in large letters on the outside of the box, and ship the
box and the drive to Plextor.
Contacting Plextor’s RMA Department
If necessary, you can contact our RMA Department and request RMA forms at:
•
rmasupport@plextor.com
•
Or by fax at 510-651-9765
•
Or by calling us at 800-886-3935
Packing Your Drive
Check the drive to make sure there is no disc inside, and if possible, pack your drive
in the original box. Some of our customers have not held on to their boxes and have
had to resort to less-than-secure methods to get drives back to us.
CAUTION
If you did not receive a box (for example, your drive came pre-installed in a
computer), we recommend you pay a packaging store (such as Mail Boxes Etc.) to
ship your drive. If you don’t have a packaging store in your area, ask for packaging
pointers when you contact us to get an RMA number before returning any drive.
: Never ship the drive with a CD still in it.
Shipping Your Drive to Plextor
Be sure to write the RMA number on the outside of the shipping box. Any drive sent
to Plextor without an RMA number will not be accepted.
NOTE
: The RMA number must be clearly visible on the outside of the shipping box.
Drives must b e sent postage prepaid. We recommend that you insure your sh ipment,
as Plextor cannot be held responsible for any damage that may occur during
shipment.
PlexWriter 40/12/40S Installation and Users Manual 49
Page 56
Appendix B: Technical Support
This page intentionally left blank.
50
PlexWriter 40/12/40S Installation and Users Manual
Page 57
Appendix C: Warranty
PLEXTOR CORP . (“Plextor”) warrants your PlexWriter 40/12/40S against any
defect in material and workmanship, under normal use, for a period of one year
following its date of purchase. In the event this product is found to be defective
within the warranty period, PLEXTOR will, at its option, repair or replace the
defective unit.
This warranty is void: a) if the unit is operated or stored under abnormal use and
maintenance conditions; b) if the unit is repaired, modified or altered, unless such
repair, modification or alteration is expressly authorized in writing by PLEXTOR;
c) if the unit is subjected to abuse, neglect, lightning strike, electrical fault, improper
packaging, or accident; d) if the unit is installed improperly; or e) if the serial
number of the unit is defaced or missing.
PLEXTOR will not, under any circumstances, be liable for direct, special, or
consequential damages such as, but not limited to, damage or lo ss of property or
equipment, loss of profits or revenues, cost of replacement goods, or expense or
inconvenience caused by service interruptions. Under no circumstances will any
person be entitled to any sum greater than the purchase price paid for the unit.
To obtain warranty service, you must contact PLEXTOR’s Technical Support
Department by calling 800-886-3935. They will attempt to diagnose and correct your
problem by phone. If the unit does not function properly, they will issue a T ech
Support Ticket number to be used on your RMA return request. You may be asked to
furnish proof of purchase to confirm that the unit is still under warranty.
All product returns must be authorized in advance by PLEXTOR’s RMA
Department. Authorization is confirmed by issuance of the RMA number, which
must be written prominently on the outside of the box in which the de fecti ve unit is
returned to PLEXTOR.
All drives returned to PLEXTOR must be securely packaged and shipped postage
prepaid.
The drive will be returned to the customer at Plextor’s expense when originating
within the United States. For a drive originating outside of the United States, the
customer is responsible for shipping costs in both directions.
NOTE
: Warranty validity is limited to that applicable in the location where the drive
was originally purchased.
PlexWriter 40/12/40S Installation and Users Manual
51
Page 58
Appendix C: Warranty
If You’re Outside the U.S. or Canada
Note that the warranty and RMA policy only apply to the United States and Canada.
If you are in South America, contact your dealer or reseller for all warranty and
RMA claims.
52
PlexWriter 40/12/40S Installation and Users Manual
Page 59
A
AC power input · 7
access time · 42
audio cable · 27
connecting to extern al drive · 28
audio cable connection · 23
audio output connector · 6, 7, 44
audio, playing · 5
B
blink rate · 31, 43
BLOCK
external drive switch setting · 7
jumper setting · 6, 13
box
contents of · 3
shipping · 3, 48, 49
buffer · 42
BURN-Proof · 2, 32
burst mode · 45
C
cable
audio · 27
power for drive · 19
SCSI · 19
cable connections · 24
external drive · 25
cable length, SCSI · 11
CD, playing · 5
CD-audio play/skip forward button · 5
CD-R
media · 29
writing speed · 1
writing speed, achieving maximum · 29
CD-R writing speed
media for 1X and 4X · 29
CD-ROM, playing · 29
CD-RW
media · 29
reading speed · 1
writing speed · 1
cleaning disc · 31
Index
closing tray · 30
computer, minimum · 2
configuration, minimum · 2, 41
connector, audio output · 6
connectors
rear panel · 44
connectors and jumpers, rear panel · 44
connectors and jumpers, rear-panel · 6
controls
front-panel · 4, 43
rear panel · 7
D
data buffer · 42
data connector · 45
diagnostics · 2, 36, 38
digital audio · 6, 13
dimensions · 46
DIP switch · 7
disc
cleaning · 31
ejecting · 5
labels · 30
loading · 43
DISC indicator · 5, 43
self-test · 38, 39
E
environmental conditions · 45
error rate specification · 42
external drive
audio cable connection · 28
connecting a single drive · 25
connecting multiple drives · 26
factory switch settings · 17
installing · 24
PlexWriter 40/12/40S Installation and Users Manual
53
Page 60
Index
F
firmware · 32
obtaining · 35
upgrading · 2, 35
flash memory · 2
formats · 42
front-panel controls · 4, 43
external drive · 4
H
hard disk size · 2, 41
headphone jack · 5, 43
headphone volume control · 43
high speed CD-RW media · 1, 29, 41, 42
host interface · 45
humidity specification · 45
I
indicators · 43
color · 31 , 43
initialization time · 42
inquiry string · 45
installation · 9, 18
drive audio cable · 23
external drive · 24
quickstart · 9
J
jumpers · 6, 10, 44
factory settings · 14
self-test and · 37, 39
setting · 14
L
label, disc · 30
laser power, adjusting with VariRec · 32,
33
M
maintenance · 35
media · 29
care and handling · 30
CD-R, 1X and 4X · 29
recommended · 41
size · 41
supported · 2, 41
memory, minimu m · 2
minimum configuration · 2, 41
MMC-3 command set · 2
Mount Rainier · 2
mounting position · 8, 18, 29
mounting rails, installing · 21
mounting the drive · 18
MRW · See Mount Rainier
MTBF · 46
O
ON/READ indicator · 5, 43
See
OPC ·
operating system · 41
optimum power control · 2, 33
orange book · 2, 41
optimum power control
P
packing for shipment · 49
parity
setting · 13
setting for internal drive · 6
performance
SCSI cable length and · 26
play/skip forward button · 5
playback, stopping · 5
playing a CD · 5
plug and play, support for · 2
power cable · 19
power connector · 6
power supply · 44
power switch · 5
PoweRec · 2, 33
precautions · 8
PRTY
external drive switch setting · 7
internal drive jumper setting · 6
setting · 13
Q
quickstart installation · 9
54
PlexWriter 40/12/40S Installation and Users Manual
Page 61
Index
R
rails, mounting · 21
RAM, mi nimum · 2, 41
read formats · 2, 42
read specification · 42
reading speed · 1, 42
rear panel controls
external drive · 7
rear-panel connectors an d j umpers · 6, 44
recording · 5, 31, 43
softwar e fo r · 8, 28
recording modes · 2, 42
red book · 41
reliability · 46
returns · 48
RMA department, contacting · 49
RMA number · 48, 49
ROPC ·
See
running optimum power
control
running optimum power control · 2
S
safety standards · 46
SCAM support · 45
SCSI cable
performance and · 26
SCSI cable length · 11
SCSI commands · 45
SCSI connection, sound board and · 27
SCSI connectors
external drive · 7
SCSI drivers
installing in Windows · 28
SCSI ID number
changing · 10
changing on external d rive · 17
non-SCAM-compliant SCSI interface
board and · 11
SCAM-compliant SCSI interface board
and · 11
setting · 15
setting for external drive · 7
setting for internal drive · 6
SCSI interface board
non-SCAM-compliant · 11
SCAM-compliant · 11
SCSI interface connector · 6, 44
SCSI ribbon cable · 19
connecting · 22
SCSI termination
changing · 15
setting · 12, 13
setting on external drive · 7, 18
security sticker · 3
self-test diagnostics · 2, 36, 38
jumper settings for · 37, 39
serial number · 18
shipping your drive · 3, 48, 49
signal line · 45
size of media · 41
sleep mode · 42
software · 8, 28
Sony/Philips digital interface · 6, 13
sound board · 27
SCSI connection and · 27
SPDIF · 6, 13
SPDIF cable connection · 23
specifications · 41
dimensions and weight · 46
environmental · 45
performance · 42
speed
monitoring · 31, 43
writing CD-DA · 42
writing CD-R · 1, 29, 42
writing CD-RW · 1, 42
stop/eject button · 5, 43
closing tray · 30
support · 47
switch
factory settings for external drive · 17
PlexWriter 40/12/40S Installation and Users Manual 55
Page 62
Index
T
tech support ticket number · 48
technical support · 47
temperature specification · 45
TERM
external drive switch setting · 7
internal drive jumper setting · 6
setting · 13
termination · 45
setting · 12, 13
termination power · 13
TEST · 13
external drive switch setting · 7
internal drive jumper setting · 6
ticket number, tech support · 48
TLA code · 18
tray
closing · 30
ejecting · 5
front door · 5
loading and unloading · 30
troubleshooting with self- test diagnostics
· 2, 36, 38
U
UDF support · 2
Ultra SCSI-3 interface · 2, 41
UNIX, settings for · 6, 7, 13
upgrading firmware · 2, 35
V
VariRec · 2, 32
changing setting · 33
default setting · 32
writing speed with · 33
volume control · 5, 43
W
wake mode · 42
warranty · 51
weight · 46
Windows
installing SCSI drivers in · 28
operating systems supported · 41
write formats · 2, 42
WRITE H indicator · 5, 31, 43
WRITE L indicator · 5, 31, 43
write methods · 2, 42
write specification
CD-DA · 42
CD-R data · 42
CD-RW · 42
writing a CD image · 2, 41
writing speed
CD-DA · 42
CD-R · 1, 29, 42
CD-R media for 1X and 4X · 29
CD-RW · 1, 42
monitoring · 31, 43
VariRec · 33
56
PlexWriter 40/12/40S Installation and Users Manual
Page 63
Notes
PlexWriter 40/12/40S Installation and Users Manual
57
Page 64
LEXTOR CORP
P
.
48383 Fremont Blvd.
Suite 120
Fremont CA 94538-6509
Phone:
Fax:
510-440-2000
800-886-3935
510-651-9755
E-mail: info@plextor.com
www.plextor.com
Loading...