Plantronics CS520-XD, CS510-XD User Manual
CS510-XD™/CS520-XD™
Wireless Headset System
User Guide
ContentsContents
Welcome 3
What’s in the Box 4
Base and Headset Basics 5
Accessories 6
Headset Set Up 7
Connect Your Desk Phone 8
Connect the Power 8
Charge the Headset 8
Connect and Configure Your Desk Phone 9
Desk Phone (standard) 9
Check Configuration and Make a Test Call 10
Desk Phone plus HL10 Lifter (sold separately) 11
Desk Phone plus EHS Cable 13
Position Your Base 14
Your Headset 15
Headset Controls 15
Talk Time 15
Battery 16
Muting Your Headset During a Call 16
Adjusting Your Headset Volume 16
Out of Range Warning Tones 16
Your Base 17
Base Phone Button and Switches 17
Subscription Button 17
Wideband/Narrowband Audio Switch 18
Auto Answer Switch 19
Daily Use 20
Place an Outgoing Call 20
Answer an Incoming Call 20
Conference Up to Three Additional Headsets 20
Troubleshooting 21
Headset 21
Desk Phone 21
2
Welcome
Congratulations on purchasing your new Plantronics product. This guide contains instructions for
setting up and using your CS510-XD/CS520-XD Wireless Headset System.
Please refer to the separate safety instructions for important product safety information prior to
installation or use of the product.
3
What’s in the Box
Base
Power supply
Headset
Model WH350-XD (binaural) shown -
Model WH300-XD (monaural) available
Telephone interface cable
4
Base and Headset Basics
Base overview
FRONT
1
2
3
1 Call/mute LED
2 Power on/subscription LED
3 Charging LED
4 Subscription button
5 Narrowband/wideband audio switch
6 Power jack
7 Handset lifter/EHS cable jack
8 Telephone interface cable jack
9 Auto answer switch
10 Listening volume dial*
11 Speaking volume dial*
12 Configuration switch*
* For installation set up
BACK
4
BOTTOM
10
6
5
8 9
7
1211
Headset overview
1
3
2
5
1 Headband
2 Volume down button
3 Headset LED
4 Volume up button
5 Call control button
6 Mute button
7 Microphone
4
6
7
5
Accessories
1
2
3
1 Electronic hookswitch cable (EHS) Electronically takes your desk phone handset off hook.
Enables remote call answer/end with your headset.
2 HL10™ lifter Automatically lifts handset and returns it to the cradle. Enables remote call
answer/end with your headset
3 Online indicator (OLI) A light that flashes once a call is activated. It allows others to know
when you are on a call.
6
Headset Set Up
Your headset comes fully assembled. You can adjust the headband for a better
fit and the mouthpiece for optimal performance.
Adjust the Headband
1 To adjust the headband, lengthen or shorten the band until it fits comfortably. The clickstop
2 Position the headset so that the leather ear cushion(s) sit comfortably over the center of your
3 For a tighter fit, gently pull the opposite end of the headset inward as shown.
feature keeps the headband securely adjusted.
ear(s). For the WH300-XD headset, position the stabilizer T-bar above your ear.
Adjust the Mouthpiece
1 Carefully bend and shape the boom with both hands as shown. Avoid bending or twisting the
boom near the microphone or earpiece.
2 Position the click stop turret and boom so that the microphone is two finger-widths from the
corner of your mouth.
2"
50.8
mm
front back
7
Loading...