USER GUIDE
Plantronics cs50/60-UsB
WIRELESS HEADSET SySTEm
0 0 0
TABLE OF CONTENTS PACKAGE CONTENTS
Headset
Earloops
Headband
AC Charger
Headset and wearing options
Package contents 3
Features 4
Setup 6
Charging 7
Positioning 7
Installing PerSono® Suite software 8
Configuration and Status 9
Adjusting fit 10
Making/answering/ending calls 11
Adjusting volume, initiating flash 12
Muting a call, initiating smart button 12
Travelling with CS60-USB 13
Headset controls 14
Base indicator lights 15
Troubleshooting for CS60-USB 15
Subscription 18
System reset 18
Battery replacement 19
Maintenance 20
Please refer to the separate Safety Instructions booklet for important product safety
information prior to installation or use.
Base
REGISTER YOUR PRODUCT ONLINE
Visit www.plantronics.com/productregistration to register your CS60-USB product online
so that we can provide you with the best possible service and technical support.
Software
PerSono Suite
software CD
3
FEATURES
Base
USB connector
Front
Charge indicator light (red)
Charge contacts
Ringer switch (On = up position)
(Off = down position)
Stand pegs
Status indicator light (green)
Headset docking cradle
Back and side
Subscription
button access
hole (paperclip
required)
Headset
AC charger port
Front:
Listening volume/mute/flash/
smart button
Call control button
Talk indicator light
Rear:
Speaker
Battery cover
Microphone
0 04 5
6“
30CM
15cm
SETUP CHARGING
1
2
1
To install base unit, first thread the USB cable through the bottom of the base so it rests
in the notch. Then attach the stand by inserting the stand pegs into the holds on the
underside of the base unit.
2
Connect USB connector to a free USB port on your computer. A USB hub can be used
but ensure that it can supply sufficient power (250 mA) to charge the headset.
Alternatively, the velcro strips included can be used to attach the base unit to a PC
monitor. However, if that causes noise or interference problems, see “Positioning”
on page 7.
1. Slide headset into charging cradle.
2. Gently press down on the headset to ensure that headset is in correct position.
Red charge indicator light on base will illuminate while charging and will go off
completely when fully charged.
AC charging only:
When your computer is powered off, the CS60-USB will not charge and the headset
standby time will decrease. Using the optional AC adapter will ensure your headset
remains charged.
USB charging only:
When your computer is powered on, the CS60-USB will charge via the USB connection.
POSITIONING
1 hour = minimum charge
to continue setup
3 hours = full charge
3
The optional AC charger can be used.
The minimum recommended separation distance is shown above.
IMPORTANT: Incorrect positioning can cause noise and interference.
6 7
INSTALLING PERSONO SUITE SOFTWARE
Plantronics PerSono Suite software provides the link between your CS60-USB headset
and compatible softphone applications on your computer. PerSono Suite software
provides the ability to remotely detect and answer/end a call from your softphone
application via the headset call control button.
In addition, PerSono Suite provides some basic configuration and status information about
the system.
Check the PerSono Suite compatibility list at www.plantronics.com/SoftphoneCompatibility
for the most current information on softphone compatibility. If your softphone is not
currently supported by PerSono Suite, please refer to page 11.
1. With the CD inserted, go to the PerSono Suite main screen and click on “Install the
PerSono Suite Software”.
2. Your softphone may require you to choose which audio device you wish to use. Please
refer to softphone documentation for details.
NOTE: Once the CS60-USB is installed, it becomes the default audio device in your computer.
You can set preferences manually in the Windows® operating system through the Sounds and
Audio Devices option in the control panel under the Audio tab.
NOTE: Once installation is complete, we recommend that you set PerSono Suite to launch
whenever the Windows® operating system starts.
System Tray Icons
After installing and running the software, one of the four system tray icons will appear
in the tray bar at the bottom of your screen showing status of headset communication
with PerSono Suite.
: No headset detected
: Headset detected, no radio link to base
: Headset detected, and radio link to base active
: Headset detected, and radio link to base is locked on
Using CS50/60-USB with Microsoft
Office Communicator
In addition to the softphones and features supported via PerSono Suite, CS50/60-USB
models support the following features for Microsoft Office Communicator (MOC). Note:
MOC features are built in to CS50/60-USB and do not require PerSono Suite software to be
installed to work with MOC.
Feature Action/description
Ring detect/answer - incoming
MOC call while headset is in base
Ring detect/answer - incoming
MOC call if headset is not in base
End a call
Initiate a call from headset if
radio link is on (green light on
base is flashing)
Initiate a call from headset if
radio link is off (green light on
base is NOT flashing)
Initiate a call from MOC
CS50/60-USB includes Intelligent Application Management logic that helps when a
PerSono Suite-supported softphone and MOC are used on the same computer.
• If ringer switch in base is on, base will ring once to
indicate incoming call. Lift headset and press headset
call control button to answer.
• Headset indicates incoming call from MOC; press
headset call control button to answer.
•
Press headset call control button to end call or insert
headset into base.
• Press call control button, headset is activated and dial
tone is heard; place call from MOC.
• Press call control button once to turn on radio link, then
press again. This will cause the MOC window to come
to the foreground and dial tone is heard; place call from
MOC.
• Place call from MOC, headset is activated automatically.
CONFIGURATION AND STATUS
Right click on the headset system tray icon and choose “Options”. This will bring
up the PerSono Suite Basic Options and Current Status Screens.
Refer to online application help for explanation details on the PerSono Suite software.
0 08 9
MAKING/ANSWERING/ENDING CALLSADJUSTING FIT
1
2
Wearing Options
Retaining
Ring
2
Snap speaker into retaining ring of
desired wearing option (headband
or earloop).
1. Adjust headband to fit.
2. Rotate headset in retaining ring
until microphone is pointing towards
your chin.
To make a call:
Press the call control button on the headset. The status indicator lights on both the base
and the headset should go on, indicating a successful link. Dial using softphone.
To answer a call:
Press the call control button on the headset to answer a call. When the ringer switch on
the side of the base is on (in the up position), the base will ring with an incoming call –
so you can receive notification of a call even when not wearing the headset. The feature is
disabled when the ringer switch is in the down position.
To end a call:
Press the call control button on the headset.
To switch between calls:
Some softphones support a feature known as “flash”. This allows you to place the current
call on or off hold or to toggle between calls. To do so, rock the headset volume control
either way for more than 2 seconds. See diagram under “Adjusting Volume, Initiating
Flash” on page 12.
When using PerSono Suite, the radio link between the headset and the base will only be
active during a call. This is the default setting intended to preserve the battery life of the
headset. However, you may wish to have the radio link active when not on a call so you
can listen to other audio sources, such as streaming audio on your PC. You can open the
radio link at any time by pressing the call control button on the headset.
NOTE: Locking the radio link on for extended periods of time will significantly reduce the
standby and talk time of the headset.
For softphones not compatible with PerSono Suite
Check the PerSono Suite compatibility list at www.plantronics.com/SoftphoneCompatibility
for the most current information on softphone compatibility.
If your softphone is not currently supported by PerSono Suite, remote detection and
answer/end via the headset does not function. Pressing the call control button on the
headset will only open and close the radio link providing audio; you must answer the call
from the softphone.
10 11
ADJUSTING VOLUME, INITIATING FLASH
Major Adjust
Minor Adjust
Headset Mute
TRAVELLING WITH CS60-USB
Rock the headset volume control back and forth to adjust listening volume.
To adjust the listen or speak volume of the softphone, please refer to the softphone user
documentation.
To adjust the listen or speak volume of the audio device on the computer, use the Sound
and Audio Devices section on the control panel in Windows®.
To initiate the flash function (see page 11 “To switch between calls”), rock the volume
control to either side for more than 2 seconds.
MUTING A CALL,
INITIATING SMART BUTTON
Gently push
side-to-side
to disassemble
You have the option to easily disassemble the CS60-USB for travel.
To conserve headset power and to
comply with air travel regulations,
you should turn off the headset by
simultaneously pressing both the call
control button and listening volume/
mute button for 5 seconds. When the
green talk indicator light on headset
blinks, release both buttons.
To turn headset back on, press the call
control button. The talk indicator light
will quickly flash green.
Disassembled unit
To mute headset, briefly press the listening volume/mute button straight in. Press again
to unmute.
You will hear 3 rapid beeps every 15 seconds to indicate mute is on.
To initiate the smart button, press and hold the listening volume/mute button for more
than 2 seconds.
12 13
NOTE: Once turned off, a single press on any button will turn the headset back on. Beware that
if not stowed properly, the CS60-USB headset may inadvertently turn back on.
0 0
Rock in one direction
for more than 2 seconds
Flash
Short key press
straight in
Mute
Ascending/descending
tones, 2 tones at limit
Rock back and forth
Listening volume
Action Tone
Press straight in and
hold for more than
2 seconds
Smart button
Flash
Making/answering/
ending calls
Short key press
Mid tone
Low battery warning
(5 minutes of talk time
remaining)
Return headset
to charging cradle
1 tone every 10 seconds
Out of range warning
– when on an
active call
Move closer to base
2 tones before range limit.
3 tones beyond range limit
and active call will be
suspended. 1 tone will
sound when returning
within range; call will be
re-established if within
15 minutes
Incoming call
notification
Press call control
button to answer call
3 repetitive tones
Feature
Key
3 tones every 15 seconds
HEADSET CONTROLS
BASE INDICATOR LIGHTS
Status indicator light (green)
Charge indicator light (red)
Action Light
Charging Red light illuminates brightly
Fully charged Red light goes off
Muted Green light flashes quickly
Headset not in base Red light illuminates softly
Headset link active Green light flashes slowly
Headset link inactive Solid green light
TROUBLESHOOTING FOR CS60-USB
Problem Solution
I've plugged everything in but
the indicator lights won’t come
on.
• Check that the USB cable is connected to a
powered computer.
• Check that the computer is turned on and not in
standby or hibernation mode.
• If using a USB hub, check that the AC power supply
is correctly connected and that the hub can supply
250 mA to charge the headset.
• If using the AC charger, check that the AC charger
jack is connected to the base unit, that the AC charger
is securely connected to a working wall outlet and that
it is the model supplied by Plantronics.
14 15
TROUBLESHOOTING FOR CS60-USB
Problem Solution
My headset does not work with
the base unit.
My headset does not work with
my softphone.
I cannot hear caller.
Callers cannot hear me.
• Headset may be out of range of the base. Move closer
to base unit until the headset is within range. Range
varies with office environment.
• Headset battery needs to be charged. See page 7.
If you are using a laptop that regularly goes into
standby or hibernation, the optional AC power
supply is provided to ensure the headset can be
continuously charged.
• Listening volume is too low. Press the volume up
button on the headset. See page 12.
• You may have to re-subscribe your headset with the
base. See page 18.
• Check compatibility list on www.plantronics.com/
SoftphoneCompatibility to ensure your softphone is
compatible for remote answer and disconnect.
• Headset battery needs to be charged. If you are
using a laptop that regularly goes into standby or
hibernation, the AC power supply is available to
ensure the headset can be continuously charged.
• CS60-USB may not be set as the default audio device
in your softphone application.
• Check that all cords are connected correctly.
• Check that the base has power (green indicator light)
and the headset battery is fully charged.
• Headset may be out of range of the base. Move
closer to base unit until the headset is within range.
Range varies with office environment.
• Adjust the listen volume on the headset (see page 12),
softphone and PC audio control.
• Ensure the headset speaker is positioned snugly
over your ear.
• Incorrect softphone model selected. Ensure you
have selected the correct softphone model through
the software.
• You may need to re-subscribe the headset.
See page 18.
• Headset is muted. Press the mute button on headset
to unmute the microphone. See page 12.
• Headset microphone boom aligned incorrectly.
Align the headset boom with your mouth.
• Speak volume is too low. Increase the speak volume
on your softphone until you can be heard by callers.
If the volume is still too low, increase the microphone
level on your computer.
• Headset battery needs to be charged. See page 7.
Problem Solution
Sound in headset is distorted.
I can hear echo in headset.
I can hear too much background
conversation or noise.
I hear static that does not allow
me to communicate.
People I talk to can hear a buzz
in the background.
The other headset I was using
to listen to music does not work
any more.
My headset stops responding
to button presses.
Battery talk time performance
is significantly degraded even
after a full charge.
Headset is uncomfortable when
worn in over-the-ear mode.
I hear beeps in the headset.
• Lower the listen volume on your softphone until
the distortion disappears.
• If the distortion is still present, lower the listen
volume control on the computer.
• Adjust volume on headset. See page 12.
• Speak volume is too high. Lower the speak volume
on your softphone until the noise disappears. If the
noise is still present, lower the microphone volume
control on the computer.
• Link to headset is lost. Try to re-establish a link by
pressing the call control button.
• Unplug the USB charger first, then unplug the AC
charger (if used) from the base for 5 seconds. Plug
the USB charger back in first, then AC adapter (if
used) to power back up.
• Reset the whole system as described on page 18.
• Move the CS60-USB base further away from your
phone.
• AC charger is plugged into a power strip. Plug the
AC charger into the wall directly.
• The CS60-USB will set itself as the default audio
device in Windows®. Use the Audio settings in
Windows® under Sounds and Audio Devices to
change the device used for audio.
• Headset may require reset. See page 18.
• Headset battery needs to be charged. See page 7.
• If you are using a laptop that regularly goes into
standby or hibernation, the optional AC power
supply is provided to ensure the headset can be
continuously charged.
• Battery is deteriorating; replace the battery with a
new battery pack. See page 19.
• Try changing earloop sizes. Experiment to find the
best fit or use the over-the-head band supplied.
• One beep every 10 seconds is caused by a low battery
warning. Recharge battery by returning headset to
the base charging cradle for one to three hours until
charge light stays lit or stops blinking.
• Two beeps is an out of range warning. Move closer
to the base.
• Three beeps every 15 seconds indicate your mute is
on. Press the mute button once to turn mute off.
16 17
SUBSCRIPTION
BATTERY REPLACEMENT
The headset and base unit are supplied subscribed to each other. However, if you wish to use
a replacement headset with the base unit, then the units must be re-subscribed as follows:
1
Return the headset to the charging cradle.
1. Use a paperclip to press and hold the
subscription button through the access
hole on the base unit for a minimum of
5 seconds. The status indicator light will
then flash.
2. Press and hold the headset mute switch
for a minimum of 5 seconds. The headset
indicator light will then illuminate.
2
Successful re-subscription is indicated
when the status indicator is fully illuminated
and the talk indicator light is off.
3. Disconnect the USB charger first, then
the AC charger (if used) from the AC
charging jack for 5 seconds.
4. Reconnect the USB charger first, then
the AC charger (if used).
If re-subscription fails within 2 minutes,
the headset will return to the un-subscribed
state. Try the re-subscription process again
or call Technical Support.
3
SYSTEM RESET
To recover from some fault conditions (refer to Troubleshooting page), you may need to
perform a system reset.
1
2
3
The custom battery inside the headset should last 2-3 years. When talk time decreases
significantly, you should replace the battery. Call Plantronics at 0800 410 014 to order one.
Once you have received it, follow directions below to replace.
1
Pinch both sides of the battery cover and lift
to remove.
3
2
Slide the battery out and gently separate
at the connection. DO NOT pull the battery
out by the wires.
4
1. Press both the call control button and
the listening volume/mute button for
5 seconds. When the talk indicator light
blinks, release both buttons.
2. Press the call control button again.
The talk indicator light will again blink
briefly to indicate the headset is back
to normal operation.
18 19
3. Disconnect the USB charger first, then
the AC charger (if used) from the AC
charging jack for 5 seconds.
4. Reconnect the USB charger first, then
the AC charger (if used).
The system reset operation is complete.
Reconnect and install the new battery. Pinch both sides of the battery cover
After replacing the battery, remember to allow 3 hours to fully charge.
and replace.
0
SOUND INNOVATION
MAINTENANCE
AUT, BEL, DEU, DNK, ESP,
FRA, GRC, ITA, IRL, LU X,
NLD, PRT, SWE, FIN, CYP,
CZE, EST, HUN, LVA, LT U,
MLT, POL, SVK, SVN.
GBR
1. Unplug the unit from the computer and the AC charger from the power source
before cleaning.
2. Clean the equipment with a damp (not wet) cloth.
3. Do not use solvents or other cleaning agents.
TECHNICAL ASSISTANCE
Visit our web site at www.plantronics.com/support for technical support including
frequently asked questions, compatibility and accessibility information. The Plantronics
Technical Assistance Center (TAC) is also ready to assist you on 0800 410 014.
www.plantronics.com
© 2006 Plantronics, Inc. All rights reserved. Plantronics, the logo design, CS60, PerSono Suite and Sound
Innovation are trademarks or registered trademarks of Plantronics, Inc. Microsoft and Windows are
either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other
countries. All other trademarks are the property of their respective owners.
Patents U.S. 5,210,791; 6,735,453; D492,667; EM 69109; and Patents Pending.
0
20
73467-03 (07/09)
Loading...