R
GET PAIRED
ANC
RL
ANC
=
=
=
=
=
TAKE CONTROL
CHARGE
The first time you power on your headphones the
pairing process begins.
NOTE If your phone supports Near Field Communication
(NFC) go to NFC pairing (Android).
1
Holding your headphones, slide the power
switch to the on position. The headphone LEDs
flash red and blue.
2
Activate Bluetooth® on your phone and set it to
search for new devices.
• iPhone® Settings > Bluetooth > On*
• Android™ > Bluetooth: On > Scan for devices*
*Menus may vary by device.
3
Select “PLT_BBPRO.”
2
Tap and hold the headphones to the phone’s NFC
tag location until NFC pairing completes. If
necessary, accept the connection.
NOTE The headphone’s NFC tag is located on the outside of
the left ear cup. (Phone tag locations vary.)
Once successfully paired, the headset LEDs stop
flashing.
NFC pairing (Android)
1
Ensure NFC is on and your phone’s display is
unlocked. (Phones may vary.)
Active Noise Canceling (ANC)
Slide the switch to activate or deactivate ANC.
ANC will block out unwanted noise.
Play/pause music
Tap the Play/pause button on the left ear cup
to play or pause music
Volume
Rotate the volume wheel forward (+) or
backward (–) to control the volume.
Track selection
Rotate the track wheel forward or backward
to control the track selection.
Open mic
While listening to music, you will be able to hear
your surroundings by tapping the Mic button to
activate or deactivate the mic.
Voice enabaled assistant
To activate Siri or Google Voice, press the Call
button for 3 seconds. (Devices may vary.)
Answer or end a call
Tap the Call button on the right ear cup.
Decline a call
Press the Call button for 2 seconds.
Mute
During a conversation, press the Mic button .
You hear “mute on” or “mute off.” While the
microphone is muted, an alert repeats every 15
minutes.
Call back last call
Double-tap the Call button .
It takes up to 2 hours to fully charge your
headphones. The LEDs turn off once charging is
complete.
TIP: To check the headphones battery status, tap the Call
button while wearing your headphones. Headphones
must be in idle state.
Your headphones have up to 24 hours of listening
time.
NEED MORE HELP?
ADJUST THE FIT
PAIR SECOND DEVICE
USE SENSORS
AIRPLANE MODE
ADVANCED OPEN MIC
CUSTOMIZE
Find a local support number
plantronics.com/support
Read detailed online user guide
plantronics.com/documentation
© 2014 Plantronics, Inc. All Rights Reserved. Bluetooth is
a registered trademark of Bluetooth SIG, Inc. and any use
by Plantronics is under license. All other trademarks are
the property of their respective owners.
Patents TEXT
pnXXXXX-XX (02.14) amXXXXX-XX
Adjust the headphones for a comfortable fit
Lengthen or shorten the band until it fits
comfortably. When not using your headphones,
fold the ear cushions in and against your body.
1
Press and hold the Call button until the LEDs
flash red and blue.
2
Activate Bluetooth on your second device and
follow steps 2 and step 3 in "Get Paired."
Smart sensors respond when you put on or take
off your headphones.
Putting on your headphones will:
• Play music
• Activate noise cancelling (when switched on)
Taking off your headphones will:
• Pause music
• Deactivate noise cancelling (when switched on)
Use your headphones when the battery is
exhausted or when traveling.
Plug in the provided 3.5 mm in-line cable to the
headphone (located on the left ear cup) and
device.
NOTE When using your headphones in this mode turns off
Bluetooth. All other features will function in this mode.
(Some phones may vary.)
When listening to music, you will be able to hear
your surroundings by activating Open Mic .
To increase or decrease the microphone level,
rotate the volume wheel forward (+) or
backward (–). To cancel Open Mic, press the Mic
button again.
Your headphones speak in English. You can
change the language and other settings using
your PC/Mac, Plantronics tool, and the provided
USB cable.
The MyHeadset™ Updater
(plantronics.com/myheadset) tool enables you to:
• Change language
• Receive firmware updates
• Turn prompts on/off
• Turn "mute off" voice alert on/off
• Turn smart sensors on/off
GET STARTED
NIRVANA
Designed in Santa Cruz, California
®
FCC statement
·
This device complies wit h pa rt 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
·This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules.
·These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communicati ons.
However, there is no guarantee that interference will not occur in a particular installation.
·If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment of f and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into a n ou tlet on a circuit different from that to which t he
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for hel p.
Certification information (SAR)
This device is also designed to meet the requirements for exposure to radio waves
established by the Federal Communications Commission (USA).
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR
MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE
FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S
AUTHORITY TO OPERATE THE EQUIPMENT.
IC Radiation Exposure Statement for Canada
This device complies with Industry Cana da licence-exempt RSS standard(s). Operatio n is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Loading...