2 Bay SATA NAS RAID Server
NAS-7201
Quick Installation Guide
Version 1.0
Table of Contents
1. OVERVIEW.................................................................................................................. 3
2. PACKAGE CONTENTS.............................................................................................. 3
3. HARDWARE INSTALLATION.................................................................................. 4
4. HARDWARE CONNECTION ....................................................................................8
5. BASIC CONFIGURATION......................................................................................... 9
5.1. WEB CONFIGURATION ACCESS................................................................................... 9
5.2. HDD FORMA TION AND RAID SETTING................................................................... 10
FURTHER INFORMATION......................................................................................... 10
- 2 -
1. Overview
Thank you for purchasing NAS-7201, the 2-bay SAT A RAID NAS server, this guide provides
physical installation and initial HDD configuration for the this NAS RAID Serve r. Please read the
information before your installation.
2. Package Contents
NAS-7201
Power adapter
Quick Installation Guide
User’s Manual CD
RJ-45 cable
- 3 -
3. Hardware Installation
Step 1: Remove the Front Case
Follow the figure below to release the screws and open the front case with the direction. Slightly
push the front case and lift up the plastic case.
Note When lift up the front case, please be careful for the LED wire
that connect to the front panel LED
Step 2: Pull out the side case
Also pull out the side case to locate the HDD mounting screws. This operation i s optional
- 4 -
Step 3: Slide in the HDDs
HDD1
HDD2
Gently slide in the SATA HDD one by one as the figure. When HDD touch the SATA connector,
slightly push the HDD to make it well connected to the SATA interface of the RAID Server
Caution Before slide in the HDD, please do make sure the HDD is in the
correct direction. Slide in and push the HDD with violent could
damage the SATA interface of the RAID Server.
- 5 -
Step 4. Lock the HDD
To lock the HDD through two screws so that the HDD can well connected to
the NAS server.
Step 5 Slide back the side case
After the HDD is installed, lock the HDD with screws and slide back the
case.
- 6 -
Step 6 Lock the front case
Follow the figure below to put back the front case.
Be careful for the LED wires. Please
align the LED wires to the space between the two HDD and close the case
gentley then push with the direction
Pull the case back and follow the
arrow direction to push the front case.
Lock the case with the screw.
- 7 -
t
4. Hardware Connection
o n
p
Steps Description
1 Connect NAS-7201 and a Switch, Hub, Router, or computer with RJ-45 Ethernet cable.
2 Connect USB printer(s) or USB storage device(s) to this device with USB cable(s). NAS-7201 can
automatically mount the USB devices connected.
3 Connect the power supply to NAS-7201.
4 Press the “Power button” to turn on NAS-7201. The HDD activate LED on the front panel will ligh
up during booting-up. NAS-7201 will be ready to use when the blue LED light s up steadily.
- 8 -
5. Basic Configuration
5.1. Web configuration access
The NAS-7201 provides GUI (Web based, Graphical User Interface) for management and administration.
The default IP address of NAS server is 192.168.0.100. You may now open your web browser, and
insert http://192.168.0.100 in the address bar of your web browser to login web configuration page.
The NAS server will prompt for login username / password please enter: admin / admin to continue the NAS Server administration.
ÍNote
In order to connect machine for administration, please
locate your PC in the same network segment (192.168.0.x)
of NAS server. If you’re not familiar with TCP/IP, please
refer to related chapter on user’s manual CD or consult your
network administrator for proper network configurations.
- 9 -
5.2. HDD Formation and RAID Setting
For new attached hard disk, you should format the HDD before any setting.
1. Go to『Maintenance』Æ『RAID Setting』to configure the server RAID level and File system.
2. Please press the Create raid system button to make configuration after modified whole configurations, then it will be automatically reboot.
3. After format completed, you can then start to access the storage of the RAID NAS server accordingly.
Further Information
This guide is used to help you startup your 2 Bay NAS server settings. It is also recommended
to check the user manual CD-ROM for more details of the system and user configuration.
- 10 -
Loading...