Planet Technology ICS-102S15, RS-485, RS-232, RS-422, ICS-102 User Manual

...
User’s Manual
ICS-100 / ICS-102 / ICS-102S15
RS-232/RS-422/RS-485 over 100Base-FX / 10/100Base-TX Media Converter
User’s Manual of ICS-10x
Trademarks
Copyright © PLANET Technology Corp. 2008. Contents subject to which revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User's Manual is accurate; PLANET disclaims liability for any inaccuracies or omissions that may have occurred.
Information in this User's Manual is subject to change without notice and does not represent a commitment on the part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User's Manual. PLANET makes no commitment to update or keep current the information in this User's Manual, and reserves the right to make improvements to this User's Manual and/or to the products described in this User's Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful interference to radio communications . Operation of this equipment in a residential area is likely to caus e harmful interference in which case the user will be required to correct the interference at whose own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presenc e of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
PLANET RS-232/RS-422/RS-485 over 10/100Base-TX/100Base-FX Media Converter User's Manual
FOR MODELS: ICS-100 / ICS-102 / ICS-102S15 REVISION: 1.1 (APRIL.2008) Part No.: 2080-AA3600-000
-2-
User’s Manual of ICS-10x
TABLE OF CONTENTS
1. INTRODUCTION .............................................................................................................1
1.1 PACKAGE CONTENTS .................................................................................................................................. 1
1.2 HOW TO USE THIS MANUAL......................................................................................................................... 1
1.3 PRODUCT DESCRIPTION.............................................................................................................................. 2
1.4 APPLICATIONS ............................................................................................................................................ 2
1.5 PRODUCT FEATURES .................................................................................................................................. 4
1.6 PRODUCT SPECIFICATION ...................................................................................................................5
2. INSTALLATION ..............................................................................................................7
2.1 HARDWARE DESCRIPTION ........................................................................................................................... 7
2.1.1 Product Layout....................................................................................................................................................7
2.1.2 LED Indicators.....................................................................................................................................................9
2.1.3 DB9 Pin Define....................................................................................................................................................9
2.1.4 ICS-10X Rear Panel............................................................................................................................................9
2.2 INSTALL THE CONVERTER.......................................................................................................................... 10
2.2.1 Stand-alone Installation.....................................................................................................................................10
2.2.2 Chassis Installation and Rack Mounting ...........................................................................................................11
3. MANAGEMENT.............................................................................................................13
3.1 OVERVIEW................................................................................................................................................ 13
3.2 REQUIREMENTS........................................................................................................................................ 13
3.3 MANAGEMENT METHODS........................................................................................................................... 14
3.3.1 Web Management.............................................................................................................................................14
3.3.2 Login the Media converter.................................................................................................................................14
4. WEB CONFIGURATION...............................................................................................16
4.1 MAIN MENU.............................................................................................................................................. 16
4.2 SYSTEM ................................................................................................................................................... 17
4.2.1 System Information...........................................................................................................................................17
4.2.2 Password Setting..............................................................................................................................................18
4.2.3 Firmware upgrade.............................................................................................................................................19
4.2.4 Factory Default..................................................................................................................................................21
4.2.5 System Reboot..................................................................................................................................................21
4.3 NETWORK CONFIGURATION....................................................................................................................... 22
4.4 OPERATION MODE .................................................................................................................................... 23
4.4.1 TCP server mode..............................................................................................................................................23
4.4.2 TCP Client mode...............................................................................................................................................29
4.4.3 UDP Client mode ..............................................................................................................................................30
4.4.4 Virtual COM mode.............................................................................................................................................31
4.4.5 Telnet Server mode...........................................................................................................................................37
4.4.6 Pair Connection– Local mode...........................................................................................................................42
4.4.7 Pair Connection – Remote mode......................................................................................................................43
-3-
User’s Manual of ICS-10x
4.5 SERIAL PORT CONFIGURATION .................................................................................................................. 47
5. SOFTWARE VCOM UTILITY.......................................................................................49
5.1 INSTALLING THE VCOM UTILITY ................................................................................................................ 49
5.2 SEARCH THE DEVICE................................................................................................................................. 51
5.3 VIRTUAL COM.......................................................................................................................................... 51
APPENDIX A.....................................................................................................................54
A.1 PLANET SMART DISCOVERY UTILITY ....................................................................................................... 54
A.2 DEVICES RJ-232/RS-422/RS-485 PIN ASSIGNMENTS.............................................................................. 55
A.3 DEVICES RJ-45 PIN ASSIGNMENTS .......................................................................................................... 55
A.4 RJ-45 CABLE PIN ASSIGNMENT.................................................................................................................. 56
A.5 FIBER OPTICAL CABLE CONNECTION PARAMETER...................................................................................... 57
A.6 POWER INFORMATION............................................................................................................................... 57
-4-
User’s Manual of ICS-10x

1. INTRODUCTION

Thank you for purchasing PLANET Serial over Fast Ethernet Media Converter – ICS-10x series. Terms of “Serial Media Converter” means the products mentioned titled in the cover page of this User’s manual

1.1 Package Contents

Open the box of the Serial Media Converter and carefully unpack it. The box should contain the following items: Check the contents of your package for following parts:
Serial Media Converter x1 CD-ROM user's manual x1 Quick installation guide x1 External 5VDC / 2.5 A pow er adapter x 1
If any of these are missing or damaged , please contact your dealer i mmediately, if po ssible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair.

1.2 How to Use This Manual

This Media Convert e r Us er Man u al i s st r uc tu r ed as fo l lows:
Section 2, Installation
It explains the functions of ICS-10x and how to physically install the ICS-10x.
Section 3, Management
The chapter explains how to manage the converter by Web interface.
Section 4, Web Configuration
It contains information about the Smart function of ICS-10x.
Section 5, So ftware VCOM Utility
It explains the software VCOM how to use with the operation Virtual COM.
Appendices
It contains cable information of ICS-10x.
-1-
User’s Manual of ICS-10x

1.3 Product Description

The Web-Smart ICS-10x series Media Converter / Device Server provide to converts Serial RS-232 / RS-422 / RS-485 communication interface over Fast Ethernet networking. There are RJ-45/SC connectors and
single-mode/multi-mode media for your needs. Ethernet signal that allows two types of segments to connect easily, efficiently and inexpensively. This converter can be used as a stand-alone unit or as a slide-in module to the PLANET Media Converter Chassis (MC-700, MC-1000 and MC-1500). It’s time saving expense for user and SI, no need to replace the existing Serial equipment and software system.
It extends the distance of deploying Serial equipments and hosts. The selectable fiber-Optic wires on the basis of distance are flexibly provided. Therefore, this product will perfectly satisfy the di verse demands while providing reliable and efficient network solutions based on the distance and budgets of installation.
The ICS-10x make connected Serial equipment becomes IP-based. That also makes them be able to connect to a TCP/IP networking immediately. Each Web-Smart converter is able to manage through the Web Interface. The powerful Web-Smart Media Converter supports Application mode, Serial operation mode connect alarm and IP address, etc. Management function helps reduce the amount of valuable time that a network administrator spends detecting and locating network problems, otherwise it requires visual inspection of cabling and equipment. Multiple connection op tions for large networking environment are available as well.

1.4 Applications

Access Control System – traditional installation
Most of the enterprise and government use access control plate a n d Mifare or RFID to authorize the entrance identity. With traditional deploy, access control machine use RS-232 or R S-485 serial inte rface and cabl es connect to login server. With connection to ICS-10x Serial over Fast Ethernet Converter, the access control machine is able to be extend over longer distances via fiber optical interface. The distance can be up to 20 km in a local ra nge. Or the ICS-10x can be lin ked to a xDSL router to get the internet access capability; the access control can be set and monitored over the internet.
Figure 1-1 Serial Converter for Access Control System application
-2-
User’s Manual of ICS-10x
Process Control
To monitor, configure and manage the Robot conveyer including other machines in a manufactu ring, PLC (Programmable Logical Control) is required. The PLC is used to drive above the manufacturing machines process. The ICS-10x can be se t to TCP Server mode and connect the PLC. The administrator can configure and set command settings through Fast Ethernet intranet to control the PLC , the administra tor and w orkstation . There i s no need to be alway s sets by the side of the I/O machine.
Figure 1-2 Serial Converter for factory PLC application
RTU Data Collect – UDP Mode
Connect with RTU (Remote Terminal Unit) to collect and monitor the data of waves, sig nal and pow er utilizati on. ICS-10x can be used to set-up UDP mode and send data over Fast Ethernet to Local server or over internet to remote server automatically.
Figure 1-3 Serial Converter for factory RTU application
-3-
User’s Manual of ICS-10x
Surveillance motion control – Pair Connection Mode
Using pair connection along with fiber optical patch cord, the ICS-10x extend RS-232/RS-485 interfaces distance from surveillance and scanner to the control keyboard/joystick which is installed in the remote monitor center.
Figure 1-4 Serial Converter for distance extend application

1.5 Product Features

Serial Interface
 One RS-232/422/485 port to one 10/100Base-TX or 100Base-FX Media Converter Cost effective solution for RS-232 to Ethernet application  Supports RS-232, 4-wire RS-422 or 2/4-wire RS485 operation  Asynchronous serial data rates up to 921600b/s
Ethernet Interface
Complies with IEEE 802.3, IEEE 802.3u 10/100Base-TX, 100Base-FX standard  Supports auto MDI/MDI-X function on RJ-45 Port
Choice of fiber-connector from SC, multi-mode / single-mode fiber
Smart Functions
Standard TCP/IP interface and versatile operation modes  Software Protocol Support ARP, ICMP,TCP/IP, UDP, HTTP server, DHCP client, Telnet server/client  Built-in IP-Base Web interface for remote management Serial Operation mode selected via Web management  Pair Connection mode for connecting two serial devices over a network  PLANET Smart Discovery utility automatically finds xxx devices on the network  Firmware upgrade via HTTP protocol
Hardware
Compact size for easy Installation:
¾ Standalone - Wall mountable or DIN-Rail mounting (Optional accessory)
-4-
¾ Co-work with PLANET MC family Media Chassis ( MC-700/1000R/1500)  LED indicators for easy network diagnose  Reset Button at the front panel for reset to factory default

1.6 PRODUCT SPECIFICAT ION

Products ICS-100 ICS-102 ICS-102S15
Hardware Specification
Interface RS-232 / RS-422 / RS-485 Connector 3-in-1 DB9 Baud rate 110 to 921600bps Character Bits 5,6,7,8
User’s Manual of ICS-10x
Serial Port
Ethernet Port
Cable Twisted-pair
Protection Built-in 1.5KV magnetic isolation
LED Indicators
Management
Operation Mode
Parity type 1,2 Stop Bit None, Even, Odd Flow Control None, RTS/CTS, Xon/Xoff
RS-232: TxD, RxD, RTS, CTS, DT R, D SR, D CD, GND
Signals
Standard Connector RJ-45 SC
Fiber Mode - Multi-Mode Single-Mode Transmission
Mode Distance 100m 2km 15km Optical
Wavelength
RS-422: Tx+, Tx-, Rx+, Rx-, GND RS-485 (2-wire): Data+, Data­RS-485 (4-wire): Tx+, Tx-, Rx+, Rx-
IEEE 802.3 10Bas-T IEEE 802.3u 10/100Base-TX, 100Base-FX
Full-Duplex / Half-Duple Full-Duplex Full-Duplex
- 1300nm 1310nm 50/125μm or
62.5/125μm multi-mode fiber cable
System: Power TP or Fiber Port: Link / Active Serial Port: Link / Active Web Management PLANET VCOM Utility PLANET Smart Discovery Utility TCP Server TCP Client UDP Client Virtual COM Telnet Server Pair Connection – Remote (Slave) Pair Connection – Local (Master)
9/125μm single-mode cable
-5-
User’s Manual of ICS-10x
Dimension (W x D x H) 97 x 70 x 26mm Weight 200g Power Supply External Power Adaptor 5V DC / 2A max. Power Consumption 5.5 Watts (maximum) Mechanical Metal
Operating Temperature: 0~50 Degree C
Environment
Emissions FCC Class A, CE Certification Class A
Standards
Regulatory Approval Compatible Media Converter
Chassis Note. Reset Button at the rear panel for reset to factory default
Storage Temperat ur e: - 1 0~ 7 0 D egr e e C Humidity: 10%~90% RH (operating)
5%~90% RH (Storage)
IEEE 802.3 10Base-T IEEE 802.3u 100Base-TX / 100Base-FX EIA/TIA RS-232/422/485
RoHS
MC-700 / 1000R / 1500
-6-
User’s Manual of ICS-10x

2. INSTALLATION

This section describes the hardware features and installation of the ICS-10X’s components on the desktop or shelf. For easier management and control of the ICS-10x, familiarize yourself with its display indicators, and ports. Front panel illustrations in this chapter display the unit LED indicators. Before connecting any network device to the Serial Media Converter, please read this chapter completely.

2.1 Hardware Description

2.1.1 Product Layout

Figure 2-1 to Figure 2-4 show layout and front panel of ICS-10X.
ICS-100 – RS-232 / RS-422 / RS-485 over 10/100Base-TX
Figure 2-1 ICS-100 panel layout
-7-
Figure 2-2 PLANET ICS-100 Front Panel
ICS-102 / ICS-102S15 – RS-232 / RS-422 / RS-485 over 10/100Base-FX
User’s Manual of ICS-10x
Figure 2-3 ICS-102 / ICS-102S15 panel layout
Figure 2-4 PLANET ICS-102 Front Panel
-8-

2.1.2 LED Indicators

LED Color Function
PWR Green Lights to indicate that the Converter is powered on.
To indicate that the Fast Ethernet Port is successfully connecting to the network at 10Mbps or 100Mbps
To indicate the Fast Ethernet Port is receiving or sending data To indicate that the UART Port is connected successfully To indicate the UART Port is receiving or sending data
TP or Fiber Green
Serial Green
Lights
Blinks Lights Blinks

2.1.3 DB9 Pin Define

DB9 Pin Define for RS-232 / RS-422 / RS-485
User’s Manual of ICS-10x
DB9-PIN RS-232
1 DCD 2 RXD 3 TXD 4 DTR RX- Data B(-) 5 GND 6 DSR TX- 7 RTS RX+ Data A(+) 8 CTS TX+ 9 RI
RS-422/485
4-wire
RS-485
2-wire

2.1.4 ICS-10X Rear Panel

The rear panel of the converter indicates one DC jack, which accepts input power with 5V DC 2.5A.
ICS-10x series
Figure 2-5 Rear Panel of ICS-10x
1. The device is a power-required device, it means, it will not work till it is powered. If your networks should active all the time, please consider using UPS (Unin terrupted Pow er Supply )
Power
Notice:
for your device. It will prevent you from network data loss or network downtime.
2. In some area, installing a surge suppression device may also help to protect your Media Converter from being damaged by unregulated surge or current to the converter or the power adapter.
-9-
User’s Manual of ICS-10x
To press and release the RESET button. The ICS-10X will back to the fa ctory default mode. Be sure that you backup the current configuration of ICS-10X; else the entire configuration will be erased when pressing the “RESET” button.
Press and release the RESET button shortly, the device will be rebooted.
Press the RESET button more than 10 seconds, the device will back to the factory default
mode; the entire configuration will be erased.

2.2 Install the Converter

This section describes how to install your ICS-10X Web Smart Media Converter and make connections to the converter. Please read the following topics and perform the procedures in the order being presented. The hardware installation of PLANET ICS-10X Web Smart Media Converter do n ot need software configuration. To install your ICS-10X on a de sktop or shelf, simply complete the following steps.

2.2.1 Stand-alone Installation

To install an ICS-10X stand-alone, on a desktop or shelf, simply complete the following steps:
Step 1: Turn off the power of the device/station in a network to which the ICS-10X will be attached. Step 2: Ensure that there is no activity in the network. Step 3: Attach RJ-45 / SC Fiber cable from the ICS-10X to the network. Step 4: Attach RS-232/RS-485 cable from the ICS-10X to the want to connect devices. Step 5: Connect the 5VDC power adapter to the ICS-10X and verify that the Power LED lights up. Step 6: Turn on the power of the device/station; the PWR LED (Green) should light when all cables are attached.
Figure 2-6 ICS-100 stand alone installation
-10-
User’s Manual of ICS-10x
Figure 2-7 ICS-102 / ICS-102S15 stand alone installation
Please refers to APPENDIX-A for detailed wiring information of the ICS-10X. To prevent from optic acceptor malfunction, check the both wires / transmitter before power on the converter.

2.2.2 Chassis Installation and Rack Mounting

To install the Media Converter in a 10-inch or 19-inch with standard rack, follow the instructions described below. Step 1: Place your ICS-10X on a hard flat surface, with the front panel positioned towards your front side. Step 2: Carefully slide in the module until it is fully and firmly fitted into the slot of the chassis.
Figure 2-8 Insert a Media Converter into an availabl e sl ot
Step 3: Attach a rack-mount bracket to each side of the Chassis with supplied screws attached to the package.
-11-
User’s Manual of ICS-10x
Step 4: After the brackets are attached to the chassis, use suitable screws to securely attach the brackets to the rack, as
shown in Figure 2-2.
Step 5: Precede with the steps 4 and steps 5 of session 2.2.1 Stand-alone Inst al lation to connect the network cabling
and supply power to your converter.
You must use the screws supplie d with the mounting brackets. Damage caused to the parts by using incorrect screws would invalidate your warranty.
Figure 2-9 Mounting the Chassis in a Rack
-12-
User’s Manual of ICS-10x

3. MANAGEMENT

This chapter describes how to manage the ICS-10X. Topics include:
- Overview
- Management methods
- Assigning an IP address to the ICS-10X
- Logging on to the ICS-10X

3.1 Overview

This chapter gives an overview of converter management. The ICS-10X provides a simply WEB browser interface. Using this interface, you can perform various converter configuration and management activities, including:
System Network Configuration Operation Mode Serial Port Configuration
Please refer to the following Chapter 4 for more details.

3.2 Requirements

Network cables. For ICS-100: Use standard network (UTP) cables with RJ45 connectors. For ICS-102 / ICS-102S15: Use Multi-mode or Single Mode fiber patch cord with SC connectors.
Subscriber PC installed with Ethernet NIC (Network Card)
Workstations of subscribers running Windows 98/ME, NT4.0, 2000/2003/XP, MAC OS X or later, Linux, UNIX or
other platform compatible with TCP/IP protocols.
Above PC installed with WEB Browser, such as Microsoft Internet Explore or Mozilla Firefox
It is recommended to use Internet Explore 6.0 or above to access Serial Media Converter.
-13-
User’s Manual of ICS-10x

3.3 Management Methods

The way to manage the ICS-10X:
- Web Management via a network or dial-up connection

3.3.1 Web Management

The PLANET Web-Smart Media Converter provides a built-in browser interface. You can manage the ICS-10X remotely by having a remote host with web browser, such as Microsoft Internet Explorer, Netscape Navigator or Mozilla Firefox.
Using this management method: The ICS-10X must have an Internet Protocol (IP) address accessible for the remote host.
Figure 3-1 Web Management over Ethernet

3.3.2 Login the Media converter

Before you start configure the ICS-10X, please note the ICS-10X is con figured through an Ethe rnet connection, make su re the manager PC must be set on same the IP subnet address.
For example, the default IP address of the ICS-10X is 192.168.0.100, then the manager PC should be set at 192.168.0.x (where x is a number between 2 and 254), and the default subnet mask is 255.255.255.0.
1. Use Internet Explor er 6.0 or above Web browser. Enter IP add ress http://192.168.0.100 (the factory-default IP address) to access the Web interface.
2. When the following login screen appears, plea se en ter the de fault u sername and pa ssword (defaul t use r name and password is "admin"). Press Login to enter the main screen of ICS-10X. The login screen in Figure 3-1 appears.
Default IP Address: 192.168.0.100 Default Account: admin Default Password: admin
-14-
User’s Manual of ICS-10x
Figure 3-2 Login screen
1. For security reason, please change and memorize the new password after this first setup.
2. Only accept command in lowercase letter under web interface.
-15-
Loading...
+ 44 hidden pages