PLANET WPG-200N User Manual
Note
– 1 – – 2 –
– 3 – – 4 –
1. Package Contents
2. Physical Installation
3. Hardware Installation
Front Panel Description
Rear Panel Description
WPG-200N
Quick Guide
CD-ROM
World-Wide Adapter Set
AntennasPower Adapter
30FPS
802.11n Wireless
Presentation Gateway
WPG-200N
Thank you for choosing PLANET WPG-200N. Before
installing the device, please verify the contents inside the
package box.
If there is any item missed or damaged, please
contact the seller immediately.
Step 1: Please turn on your projector first, and connect
HDMI or D-sub cable of the projector to
WPG-200N. Now you can power on WPG-200N.
Step 2: When the projector shows the default screen as
below, it indicates WPG-200N is ready now.
Power LED
LAN Port
(Connect to a client PC of Ethernet)
2 dBi Detachable Antenna x 2
(US/EU/UK/AU)
Power Connector
(5V DC Input)
15 Pin D-Sub VGA Port
(Connect to the projector)
Audio Out
(Connect to speaker
or headphone)
HDMI Port
(Connect to the projector)
4. Software Installation – Windows
Step 1: Site survey the wireless signal of WPG-200N,
and connect your PC with it wirelessly.
* The above hardware installation of WPG-200N is
connected by HDMI cable. The VGA cable works as well.
Default SSID: WPG-200N
* The connection information can be found from the
projector screen.
Power
Power
Adapter
HDMI
– 7 – – 8 –
– 5 – – 6 –
FURTHER INFORMATION
The above steps introduce simple installations and
configurations for WPG-200N. For fur ther configurations of
the utility (WPG), Virtual Extended Screen, and Wi-Fi
AP-Client etc, please refer to the user’s manual in the CD.
If you have further questions, please contact the local
dealer or distributor where you purchased this product.
2011-E60040-000
1. First, make sure the Wi-Fi function of your smartphone
or PDA is enabled, and connect the Smartphone or PDA
with WPG-200N.
2. Open the browser of the smartphone or PDA, and it
would redirect to the WPG-200N web page (or you can
enter the default IP address 192.168.1.1 to access it.).
Download the MobiShow client software, and execute
the installation program.
3. Open “Programs” on your smartphone or PDA, and
select “MobiShow” icon to launch the client
software.
4. The SSID of available access points will be listed on
your smartphone or PDA. Select WPG-200N.
5. Input the login code displayed on the projector screen,
and the following main menu will be shown on your
phone.
6. Select which feature to use. To project the screen of
your phone, click on the “Screen” icon. To make a
presentation, select the “PtG” icon. To project the
photos from your phone, select the “Photo” icon.
Step 2: Open the web browser and it will redirect to
WPG-200N home page automatically, or you can
enter the default IP address 192.168.1.1 to
access it.
Step 3: Download the client utility (WPG) of Windows
7/Vista/XP and execute it. After installing the
program, you’ll see WPG shortcut on your PC
desktop.
Step 4: Launch WPG on the desktop, then input the login
code. The login code can be found from the
projector screen.
Step 5: Click the button to start projection, or choose
one of the numbers 1~4 to project to the split
screen.
Default IP Address: 192.168.1.1
Default Username: admin
Default Password: admin
Note
Please make sure the firewall in Windows will
allow the WPG software to pass through.
Addendum. Windows Mobile 5/6
Loading...