PLANET WNRT-632 User Manual

transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any

form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior

written permission of PLANET.

PLANET makes no representations or warranties, either expressed or implied, with respect to the contents hereof

and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software

described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase,

the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing,

repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company

reserves the right to revise this publication and to make changes from time to time in the contents hereof without

obligation to notify any person of such revision or changes.

All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their

respective holders.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

4. Consult the dealer or an experienced radio technician for help.

FCC Caution:

To assure continued compliance, (example-use only shielded interface cables when connecting to computer or

peripheral devices) any changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two conditions: (1) This device may not cause harmful interference, and (2) this Device must accept any interference received, including interference that may cause undesired operation.

Federal Communication Commission (FCC) Radiation Exposure Statement

This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid

the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be

less than 20 cm (8 inches) during normal operation.

CE mark Warning

This is a class B device, in a domestic environment; this product may cause radio interference, in which case the

user may be required to take adequate measures.

Energy Saving Note of the Device

This power required device does not support Stand by mode operation.

For energy saving, please remove the DC-plug or push the hardware Power Switch to OFF position to disconnect

the device from the power circuit.

Without remove the DC-plug or switch off the device, the device will still consuming power from the power circuit. In

the view of Saving the Energy and reduce the unnecessary power consuming, it is strongly suggested to switch off

or remove the DC-plug for the device if this device is not intended to be active.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT

AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal Equipment and the

mutual recognition of their conformity (R&TTE).

The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment

and Satellite Earth Station Equipment) As of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it. However, special

attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment.

All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use

of the equipment.

National Restrictions

This device is intended for home and office use in all EU countries (and other countries following the EU directive

1999/5/EC) without any limitation except for the countries mentioned below:

Country Restriction Reason/remark

Bulgaria None

France

Italy None

Luxembourg None

Norway Implemented

Russian Federation None Only for indoor applications

Outdoor use limited to 10 mW e.i.r.p. within the band 2454-2483.5 MHz

General authorization required for outdoor use and

public service

Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012

If used outside of own premises, general authorization is required

General authorization required for network and service supply(not for spectrum)

This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund

WEEE Regulation

To avoid the potential effects on the environment and human health as a result of the presence of

hazardous substances in electrical and electronic equipment, end users of electrical and electronic

equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of

WEEE as unsorted municipal waste and have to collect such WEEE separately.

Revision

User’s Manual for PLANET 802.11n Wireless Gigabit Broadband Router

Model: WNRT-632

Rev: 1.1 (July. 2011)

Table of Contents

Chapter 1 Introduction ................................................................................................... 7

1.1 Packing Contents................................................................................................7

1.2 Spec Summary Table ..........................................................................................8

1.3 Hardware Configuration ......................................................................................9

1.4 LED indicators................................................................................................... 11

1.5 Procedure for Hardware Installation..................................................................12

Chapter 2 Making Configuration.................................................................................. 14

2.1 Login to Configure from Wizard ........................................................................15

2.2 System Status ...................................................................................................19

2.3 Advanced ..........................................................................................................20

2.3.1 Basic Setting...........................................................................................20

2.3.1.1 Primary Setup – WAN T

ype, Virtual Computers............................ 21

2.3.1.2 DHCP Server................................................................................25

2.3.1.3 Wireless........................................................................................ 26

2.3.1.4 Change Password ........................................................................31

2.3.2 Forwarding Rules....................................................................................32

2.3.2.1 Virtual Server................................................................................ 32

2.3.2.2 Special AP.....................................................................................33

2.3.2.3 Miscellaneous Items .....................................................................34

2.3.3 Security Settings.....................................................................................35

2.3.3.1 Packet Filters................................................................................ 36

2.3.3.2 Domain filters................................................................................41

2.3.3.3 URL Blocking ................................................................................ 43

2.3.3.4 Internet Access Control.................................................................45

2.3.3.5 Miscellaneous Items .....................................................................52

2.3.4 Advanced Settings ..................................................................................53

2.3.4.1 System Time ................................................................................. 54

2.3.4.2 System Log...................................................................................55

2.3.4.3 DDNS Service............................................................................... 56

2.3.4.4 SNMP ...........................................................................................57

2.3.4.5 Routing .........................................................................................58

2.3.4.6 Schedule Rule ..............................................................................60

2.3.4.7 QoS Rule ...................................................................................... 61

2.3.5 Toolbox ...................................................................................................62

2.3.5.1 View Log....................................................................................... 62

2.3.5.2 Firmware Upgrade ........................................................................ 63

2.3.5.3 Backup Setting.............................................................................. 63

2.3.5.4 Reset to default............................................................................. 64

2.3.5.5 Reboot .......................................................................................... 64

2.3.5.6 Miscellaneous Items .....................................................................65

Appendices and Index.................................................................................................... 66

802.1x Setting.........................................................................................................66

WPA Settings ..........................................................................................................71

FAQ and Troubleshooting .............................................................................................. 79

What can I do when I have some trouble at the first time? ..............................79

How do I connect router by using wireless?.....................................................81

Thank you for purchasing WNRT-632. This manual guides you on how to install and properly use the

WNRT-632 in order to take full advantage of its features.

1.1 Packing Contents

Make sure that you have the following items:

 WNRT-632 x 1

 Power Adapter x 1

 Ethernet Cable x 1

 CD x 1 (Quick Installation Guide and User’s Manual)

 Quick Installation Guide x 1

Note: If any of the above items are missing, please contact your supplier for support.

1.2 Spec Summary Table

Device Interface WNRT-632

Ethernet WAN RJ-45 port, 10/100/1000Mbps, auto-MDI/MDIX 1

Ethernet LAN RJ-45 port, 10/100/1000Mbps, auto-MDI/MDIX 4

Antenna 3dBi detachable antenna 2

WPS Button For WPS connection 1

Wireless Enable/disable

LED Indication Power/Status / WAN / LAN1 ~ LAN4/ Wi-Fi ●

Power Jack

Wireless LAN (WiFi)

Standard IEEE 802.11b/g/n compliance ●

SSID SSID broadcast or in stealth mode ●

Channel Auto-selection, manually ●

Security WEP, WPA, WPA-PSK, WPA2, WPA2-PSK ●

WPS WPS (Wi-Fi Protected Setup) ●

WMM WMM (Wi-Fi Multimedia) ●

Functionality

Ethernet WAN PPPoE, DHCP client, Static IP, PPTP, L2TP ●

WAN Connection Auto-reconnect, dial-on-demand, manually ●

One-to-Many NAT

To enable or disable Wireless Radio

DC Power Jack, powered via external DC 12V/1A switching

power adapter

Virtual server, special application, DMZ, Super DMZ (IP

●

Pass through)

NAT Session Support NAT session 20000

SPI Firewall IP/Service filter, URL blocking, MAC control ●

DoS Protection DoS (Deny of Service) detection and protection ●

Routing Protocol Static route, dynamic route (RIP v1/v2) ●

Management SNMP, UPnP IGD, syslog, DDNS ●

Administration Web-based UI, remote login, backup/restore setting ●

Performance NAT up to 700Mbps and Wireless up to150Mbps

Environment & Certification

Package Information

Operation Temp. Temp.: 0~40°C, Humidity 10%~90% non-condensing ●

Storage Temp. Temp.: -10~70°C, Humidity: 0~95% non-condensing ●

EMI Certification CE/FCC compliance ●

RoHS RoHS compliance ●

Package dimension (W x D x H) (mm) 245 x 207 x 60

Package weight (gross weight) (g) 674

1.3 Hardware Configuration

Figure 2-1 Front Panel

WLAN

LED

Power

LED

Status

LED

WPS

Button

Note: Reset = Press Wi-Fi on/off and WPS buttons simultaneously about 5 sec.

WAN

LED

LED1~4 for

LAN1~4

WiFi on/off

Button

Figure 2-2 Rear Panel

Antenn

Power

WAN LAN 1~4

Power

1.4 LED indicators

LED status Description

Status Green in flash Device status is working.

Green RJ45 cable is plugged WAN LED

LAN LED

WiFi LED

Green in flash Data access

Green RJ45 cable is plugged

Green in flash Data access

Green WLAN is on

Green in flash Data access

Green in fast flash Device is in WPS PBC mode

Green in dark Wi-Fi Radio is disabled

1.5 Procedure for Hardware Installation

Step 1. Attach the antenna.

1.1. Remove the antenna from its plastic

wrapper.

1.2. Screw the antenna in a clockwise direction

to the back panel of the unit.

1.3. Once secured, position the antenna

upward at its connecting joint. This will ensure

optimal reception.

1.Turn off the Power Switch

Step 2 Insert the Ethernet cable into LAN

Port:

Insert the Ethernet patch cable into LAN port

on the back panel of Router, and an available

Ethernet port on the network adapter in the

computer you will use to configure the unit.

first.

Step 3 Insert the Ether

Wired WAN port:

Insert the Ethernet patch cable form DSL

Modem into Wired WAN port on the back panel

of Router.

Step 4. Power on Router:

4.1. Connect the power adapter to the receptor

on the back panel of your Router and Push

Power switch

net patch cable into

Step 5. Complete the setup.

5.1. When complete, the Status LED will flash.

This product provides Web based configuration scheme, that is, configuring by your Web browser, such as

Mozilla Firefox or or Internet Explorer. This approach can be adopted in any MS Windows, Macintosh or

UNIX based platforms.

2.1 Login to Configure from Wizard

Configure the settings by the following steps:

2.1 Open web browser, type the default IP

address (

System Password: “admin”

2.2 Select “Wizard”, and then click “Enter”.

http://192.168.0.1)

2.3 Start to configure Internet setting by click

“Next >” button.

2.4 Modify the Old Password by entering a

new one. Click “Next >” button if you don’t want to change the password.

2.5 Select

“Auto Detecting WAN Type” and

then click “Next >” button.

2.6 Click “Next >” to continue the setting.

Example, the Dynamic WAN type is

detected.

2.7 Modify the Wireless settings.

Click “Next >” if setting by default. (Strongly suggest changing the SSID to protect your

wireless network.)

2.8 Setup the Wireless Security

Click “Next >” if setting by default. (Strongly suggest configuring the security to protect

your wireless network.)

2.9 Make sure all the settings are configured

correctly, and then click “Apply Settings” button.

You can ignore the wan connection test

by uncheck the “Do you want to proceed

the network testing?”

2.10 Wait for the system applying the

settings automatically.

2.11 Click “Finish” to c

omplete the Setup.

Or you can click “Configure Again” to setup the wizard again.

2.2 System Status

This option provides the function for observing this product’s working status:

WAN Status:

If the WAN port is assigned a dynamic IP, there may appear a “Renew” or “Release” button on the Sidenote column. You can click this button to renew or release IP manually.

Statistics of WAN:

Enables you to monitor inbound and outbound packets

2.3 Advanced

2.3.1 Basic Setting

Please Select “Advanced Setup” to Setup

2.3.1.1 Primary Setup – WAN Type, Virtual Computers

Click “Change”

This option is primary to enable this product to work prop

depend on the WAN type. Choose correct WAN type before you start.

1. LAN IP Address: the local IP address of this device. The computers on your network must use the LAN IP address of your product as their Default Gateway. You can change it if necessary.

2. WAN Type: WAN connection type of your ISP. You can click Change button to choose a correct one from the following four options:

A. Static IP Address: ISP assigns you a static IP address.

B. Dynamic IP Address: Obtain an IP address from ISP automatically.

C. Dynamic IP Address: Telstra BigPond (Australia's ISP)

D. PPP over Ethernet: Some ISPs require the use of PPPoE to connect to their services.

E. PPTP: Some ISPs require the use of PPTP to connect to their services.

F. L2TP: Some ISPs require the use of L2TP to connect to their services

G. Russia PPPoE(Dual Access): Russia PPP over Ethernet(Dual Access) is a common connection

method used for XDSL.

H. Russia PPTP(Dual Access): Russia PPP Tunneling(Dual Access) can support multi-protocol

erly. The setting items and the web appearance

Virtual Private Network(VPN).

Static IP Address: ISP assigns you a static IP address:

WAN IP Address, Subnet Mask, Gateway, Primary and Secondary DNS: enter the proper setting provided

by your ISP.

Dynamic IP Address: Obtain an IP address from ISP automatically.

Host Name: optional. Required by some ISPs, for example, @Home.

Renew IP Forever: this feature enables this product to renew your IP address automatically when the lease

time is expiring-- even when the system is idle.

PPP o

ver Ethernet: Some ISPs require the use of PPPoE to connect to their services.

PPPoE Account and Password: the account and password your ISP assigned to you. For security, this field

appears blank. If you don't want to change the password, leave it empty.

PPPoE Service Name: optional. Input the service name if your ISP requires it. Otherwise, leave it blank.

Maximum Idle Time: the amount of time of inactivity before disconnecting your PPPoE session.

Set it to zero or enable Auto-reconnect to disable this feature.

Maximum Transmission Unit (MTU): Most ISP offers MTU value to users. The most common MTU value is

1492.

Connection Control: There are 3 modes to select:

Connect-on-demand: The device will link up with ISP when the clients send outgoing packets.

Auto-Reconnect (Always-on): The device will link with ISP until the connection is established.

Manually: The device will not make the link until someone clicks the connect-button in the Status-page.

PPTP: Some ISPs require the use of PPTP to connect to their services First, please check your ISP assigned and Select Static IP Address or Dynamic IP Address.

My IP Address and My Subnet Mask: the private IP address and subnet mask your ISP assigned to you.

Server IP Address: the IP address of the PPTP server.

PPTP Account and Password: the account and password your ISP assigned to you. If you don't want to

change the password, keep it empty.

Connection ID: optional. Input the connection ID if your ISP requires it.

Maximum Idle Time: the time of no activity to disconnect your PPTP session. Set it to zero or enable

Auto-reconnect to disable this feature. If Auto-reconnect is enabled, this product will connect to ISP

automatically, after system is restarted or connection is dropped.

Connection Control: There are 3 modes to select:

Connect-on-demand: The device will link up with ISP when the clients send outgoing packets.

Auto-Reconnect (Always-on): The device will link with ISP until the connection is established.

Manually: The device will not make the link until someone clicks the connect-button in the Status-page.

L2TP: Some ISPs require the use of L2TP to connect to their services

First, please check your ISP assigned and Select Static IP Address or Dynamic IP Address.

For example: Use Static

My IP Address and My Subnet Mask: the private IP address and subnet mask your ISP assigned to you.

Server IP Address: the IP address of the PPTP server.

PPTP Account and Password: the account and password your ISP assigned to you. If you don't want to

change the password, keep it empty.

Connection ID: optional. Input the connection ID if your ISP requires it.

Maximum Idle Time: the time of no activity to disconnect your PPTP session. Set it to zero or enable

Auto-reconnect to disable this feature. If

Auto-reconnect is enabled, this product will connect to ISP

automatically, after system is restarted or connection is dropped.

Connection Control: There are 3 modes to select:

Connect-on-demand: The device will link up with ISP when the clients send outgoing packets.

Auto-Reconnect (Always-on): The device will link with ISP until the connection is established.

Manually: The device will not make the link until someone clicks the connect-button in the Status-page.

Russia PPPoE(Dual Access)

This mode only activate for Russia ISP that support dual layer Access to the Internet.

Please check with your ISP for the detail setting.

Russia PPTP(Dual Access)

This mode only activate for Russia ISP that support dual layer Access to the Internet.

Please check with your ISP for the detail setting.

Virtual Computers (Only for Static and dynamic IP address Wan type)

Virtual Computer enables you to use the original NAT feature, and allows you to setup the one-to-one

mapping of multiple global IP address and local IP address.

 Global IP: Enter the global IP address assigned by your ISP.

 Local IP: Enter the local IP address of your LAN PC corresponding to the global IP address.

 Enable: Check this item to enable the Virtual Computer feature.

2.3.1.2 DHCP Server

1. DHCP Server: Choose “Disable” or “Enable.”

2. Lease time: This is the length of time that the client may use the IP address it has been

assigned by dhcp server.

3. IP pool starting Address/ IP pool starting Address: Whenever there is a request, the DHCP

server will automatically allocate an unused IP address from the IP address pool to the requesting

computer. You must specify the starting and ending address of the IP address pool.

4. Domain Name: Optional, this information will be passed to the client.

5. Primary DNS/Secondary DNS: This feature allows you to assign DNS Servers

6. Primary WINS/Secondary WINS: This feature allows you to assign WINS Servers

7. Gateway: The Gateway Address would be the IP address of an alternate Gateway.

This function enables you to assign another gateway to your PC, when DHCP server

offers an IP to your PC.

8. DHCP Client List: List connected DHCP Clients.

2.3.1.3 Wireless

Wireless settings allow you to set the wireless configuration items.

Wireless: The user can enable or disable wireless function.

Schedule Setting: The device can turn off Wireless depend as Schedule.

Network ID (SSID): Network ID is used for identifying the Wireless LAN (WLAN). Client stations can roam

freely over this product and other Access Points that have the same Network ID. (The factory setting is

“default”)

SSID Broadcast: The router will Broadcast beacons that have some information, including SSID so that The wireless clients can know how many ap devices by scanning function in the network. Therefore,

This function is disabled; the wireless clients can not find the device from beacons.

Channel: The radio channel number. The permissible channels depend on the Regulatory Domain.

+ 60 hidden pages