Planet WNRT-625G User Manual

802.11n 3G Broadband Router

WNRT-625G

User’s Manual

Copyright © 2009 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemica l, manual or otherwise, without the prior written permission of PLANET.

PLANET makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective holders.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital devic e, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequenc y energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televisio n reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio technician for help.

FCC Caution:

To assure continued compliance, (example-use only shielded interface cables when connecting to computer or peripheral devices) any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two conditions: (1) This device may not cause harmful interference, and (2) this D evice must accept any interference received, including interference that may cause undesired operation.

Federal Communication Commission (FCC) Radiation Exposure Statement

This equipment complies with FCC radiation exposure set forth for an unc ontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE).

The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allo wed at

to ensure the safe use of the equipment. all times

WEEE regulation

To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do

not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.

Revision

User’s Manual for PLANET 802.11N Wireless Router Model: WNRT-625G Rev: 1.0 (April. 2009)

TABLE OF CONTENTS

CHAPTER 1 INTRODUCTION................................................................................................................. 5

1.1

ACKAGE CONTENTS

1.2

EATURES

1.3

PECIFICATION

CHAPTER 2 HARDWARE INSTALLATION / NETWORK SETUP.................................................... 7

2.1

UTLOOK

2.2

ARDWARE INSTALLATION

2.3

ETWORK SETUP

CHAPTER 3 WEB LOGIN....................................................................................................................... 13

CHAPTER 4 QUICK SETUP................................................................................................................... 15

CHAPTER 5 GENERAL SETUP............................................................................................................. 27

5.1

YSTEM

5.2

WAN ....................................................................................................................................30

5.3

LAN.....................................................................................................................................37

5.4

IRELESS

5.5

QOS......................................................................................................................................51

5.6

NAT .....................................................................................................................................54

5.7

IREWALL

CHAPTER 6 STATUS .......................................................................................................................... 71

6.1

NTERNET CONNECTION

6.2

EVICE STATUS

6.3

YSTEM LOG

6.4

ECURITY LOG

6.5

CTIVE

6.6

TATISTICS

...............................................................................................................................5

...............................................................................................................................7

................................................................................................................................28

.............................................................................................................................39

.............................................................................................................................63

........................................................................................................................72

DHCP C

............................................................................................................................74

..............................................................................................................5

........................................................................................................................5

.....................................................................................................8

..................................................................................................................11

........................................................................................................71

....................................................................................................................72

......................................................................................................................73

LIENT

.........................................................................................................74

CHAPTER 7 TOOLS............................................................................................................................ 75

7.1

ONFIGURATION TOOLS

7.2

IRMWARE UPGRADE

7.3

ESET

...................................................................................................................................77

CHAPTER 8 TROUBLESHOOTING................................................................................................ 78

........................................................................................................75

............................................................................................................76

Chapter 1 Introduction

Thank you for purchasing WNRT-625G. This manual guides you on how to install and properly use the WNRT-625G in order to take full advantage of its features.

1.1 Package Contents

•

WNRT-625G x 1

•

Stand x 1

•

Ethernet Cable x 1

•

Power Adapter x 1

•

CD-ROM (included user’s manual) x 1

•

Quick Installation Guide x 1

Note:

1.2 Features

z Dual WAN Interfaces: WAN port for cable or wired DSL service + 3G mobile connection z Supports UMTS/HSDPA Mobile Internet Service z IEEE 802.11n (Draft 2.0) wireless technology compliant with 802.11b/g standard z Capable of up to 300Mbps data rate z Supports Wi-Fi Protected Setup (WPS) z Advanced security: 64/128-bit WEP, WPA –TKIP(PSK), WPA2-AES(PSK), 802.1x z Access Private LAN Servers from the Public Network z Equipped with four LAN ports (10/100M) and one WAN port (10/100M), Auto-MDI/MDI-X

z Supports DHCP Server z System status monitoring includes Active DHCP Client, Security Log and Device/Connection

z Web-based GUI for and Wizard setup for easily configuration z Remote Management allows configuration and upgrades from a remote site z Supported Internet types: Dynamic / Static IP / PPPoE / PPTP / L2TP / Telstra Big Pond z MAC / IP filter access control, URL blocking ; SPI firewall + DoS prevention protection z Supports UPnP function

If any of the above items are missing, please contact your supplier for support.

supported

Status

1.3 Specification

Standard IEEE 802.11b/g, 802.11n Draft 2.0, IEEE802.3u

11b mode: DSSS

Signal Type

Modulation

WAN Port 1 x 100Base-TX, Auto-MDI/MDI-X LAN Port 4 x 100Base-TX, Auto-MDI/MDI-X Antenna connector 2 x Fixed 3dBi Dipole Antenna Data Encryption

Output Power

11g mode: OFDM 11n mode: OFDM, MIMO

802.11b: DBPSK, DQPSK, CCK

802.11g: BPSK, QPSK, 16QAM, 64QAM

802.11n: BPSK, QPSK, 16QAM, 64QAM

64 bit / 128 bit WEP, WPA-PSK, WPA, WPA2, 802.1x encryption 11b: 18 dBm

11g: 15 dBm 11n: 15dBm

Data Rate N Data Rate Receiver

Sensitivity Session

LED Indicators PWR, WLAN, WAN * 1, LAN * 4 Compatible Mobile

network Compatible mobile

service provider Compatible internet

PC adapter list

IEEE 802.11b: 11/5.5/2/1M IEEE 802.11g: 54/48/36/24/18/12/9/6

Table (1)

11b CCK 1.0Mbps -94dbm 11b CCK 11.0Mbps -91dbm 11g OFDM 6Mbps -92dbm 11g OFDM 54Mbps -76dbm 11n 20MHz MCS7 : -72dbm 11n 40MH MCS7 : -70dbm

2000

UMTS/HSDPA

Please contact with PLANET Technical Support for latest information.

N Data Rate Table (1)

MCS Index

0 7.2 15.0 1 14.4 30.0 2 21.7 45.0 3 28.9 60.0 4 43.3 90.0 5 57.8 120.0 6 65.0 135.0 7 72.2 150.0

HT20 HT40

Data rate (Mbps) @ 400ns GI

Chapter 2 Hardware Installation / Network Setup

Please follow the below instruction to build the wireless network connection bet ween WNRT-625G and your computers.

2.1 Outlook

Front Panel

For 3G / 3.5G modem USB Adapter

LED Name Light Status Description POWER WLAN

WAN LNK/ACT

USB LNK/ACT

LAN 1-4 LNK/ACT

On Router is switched on and correctly powered. On Wireless WPS function is enabled.

Off Wireless network is switched off. Flashing Wireless LAN activity (transferring or receiving data). On WAN port is connected. Off WAN port is not connected. Flashing WAN activity (transferring or receiving data). On USB modem is connected.

Off USB modem is not connected. Flashing USB modem activity (transferring or receiving data). On LAN port is connected.

Off LAN port is not connected. Flashing LAN activity (transferring or receiving data).

Back Panel

Antenna

Reset / WPS

Item Name Antenna

Radio ON/OFF

Reset / WPS

1 - 4 WAN Power

Power

1-4 (LAN)

Radio ON/OFF

Description Attached 3dBi dipole antenna.

Switch the button to activate or deactivate the wireless functions. Reset the router to factory default settings (clear all settings) or start WPS

function. Press this button and hold for 10 seconds to restore all settings to factory defaults, and press this button for less than 5 seconds to start WPS function.

Local Area Network (LAN) ports 1 to 4. Wide Area Network (WAN / Internet) port. Power connector, connects to power adapter.

WAN

2.2 Hardware Installation

1. Locate an optimum location for the WNRT-625G. Th e b est place for your WNRT-625G is usually

at the center of your wireless network, with line of sight to all of your mobile stations.

2. Adjust the antennas of WNRT-625G. Try to adjust them to a position that can best cover your wireless network. The antenna’s position will enhance the receiving sensitivity.

3. There are two way connecting to Internet, One is via 3G USB port, and another is from WAN port.

3-1. Connect your 3G/3.5G USB modem to the USB port located in front panel of WNRT-625G.

NOTE:

Please also check with your local dealer or PLANET Web site for supported 3G/3.5G USB adapter

3-2. Connect ADSL/Cable Modem to WAN port of WNRT-625G via RJ-45 Ethernet cable.

4. Connect all of your netw ork devices to LAN port of WNRT-625G. Connect all your computers,

network devices (network-enabled consumer devices other than computers, like game console, or switch / hub).Connect one of the LAN ports on WNRT-625G to your LAN switch/hub or a computer with a RJ-45 cable.

5. Plug in power adapter and conn ect to power source. After power on, WNRT-625G will start to operate.

6. Please check all LEDs on the front panel. ‘PWR’ LED should be steadily on. WAN and LAN LEDs should be on if the computer / network device connected to the respective port of the router is powered on and correctly connected. If PWD LED is not on, or any LED you expected is not on, please recheck the cabling, or jump to ‘Troubleshooting’ for possible reasons and solution.

Note:

1. ONLY use the power adapter supplied with the WNRT-625G. Otherwise, the product may be

damaged.

2. If you want to reset WNRT-625G to default settings, press and hold the RST(reset) button over

30 seconds and release. And then wait for WNRT-625G restart.

2.3 Network Setup

After you install your WNRT-625G, the TCP/IP settings should be set to obtain an IP address from a DHCP server (WNRT-625G) automatically. To verify your IP address, please follow the steps below:

1. Click on Start > Run.

2. In the run box type “cmd” and click OK. (Windows VistaR users type cmd in the Start .Search box.)At the prompt.

3. Type “ipconfig” and press Enter. It will display the IP address, subnet mask, and the default gateway of adapter.

4. If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your router. Some firewall software programs may block a DHCP request on newly installed adapters.

Assign a static IP address

If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:

1. - Windows Vista® - Click on Start > Control .Panel > Network .and .Internet

>Network .and .Sharing .Center > Manage Network Connections.

- Windows® XP - Click on Start > Control .Panel > Network Connections.

- Windows® 2000 - From the desktop, right-click My Network Places > Properties.

2. Right-click on the Local Area Connection which represents your network adapter and select Properties.

3. Highlight Internet .Protocol .(TCP/IP) and click Properties.

4. Click Use .the .following .IP .address and enter an IP address that is on the same subnet as your

network or the LAN IP address on your router. Example: If LAN IP address of WNRT-625G is 192.168.0.1, make your IP address 192.168.0.X where X is a number between 2 and 99. Make sure that the numb er you choos e is not in use on the net work. Set Default Gateway the same as the LAN IP address of your router (192.168.0.1). Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The Secondary DNS is not needed or you may enter a DNS server from your ISP.

5. Click OK twice to save your settings.

Chapter 3 Web Login

WNRT-625G with an assigned IP address allows you to monitor and configure via web browser (e.g., MS Internet Explorer or Netscape).

1. Open your web browser.

2. Enter the IP address of your WNRT-625G in the address field (default IP address is

http://192.168.0.1

3. Please enter your User Name and Password in the dialog box. Default User Name and Password are both “admin”. Click OK.

4. Then you will see the WNRT-625G HOME screen as below.

The left panel provides four options, Quick Setup, General Setup, Status Information and Tools.

Section Description

Quick Setup

General Setup

Status Info

Tools

Select your Internet connection type and then input the co nfigurations needed to connect to your Internet Service Provider (ISP). This section contains configurations for the Broadband router’s advance functions such as: Port Forwarding, Virtual Server, Access Control, Hacker Attack Prevention, DMZ, Special applications and other functions to meet your LAN requirements. You can a lso configure the wireless detail settings here. This option provides you the system information, Internet Connection, D evice Status, Security Log and DHCP client Log information. This option contains Configuration tools, Firmware Upgrade and Reset functions.

Chapter 4 Quick Setup

This section describes the basic configuration of the WNRT-625G and allows you to connect to Internet easily.

4.1 Time Zone

The time information is used for Log entries and Firewall settings. You can keep the default Time Server address or set a new IP address for your router to synchronize its time. Click “Next” to continue.

Parameter

Set Time Zone

Time Server Address

Enable Daylight Savings

Click “Next” button to proceed to the next step.

Description

Select the time zone of the country you are currently in. The router will set its time based on your selection. Remain it as default or, you can manually assign an IP address of the Time Server. The information of Timer Server can be found in the following URL link: http://www.eecis.udel.edu/~mills/ntp/servers.html or http://www.ntp.org. The router can also take Daylight savings into account. To enable this function, check/tick the “Enable Function” box and select which days this function will work.

4.2 WAN Type

Before establishing the Internet connection, please be sure to check with your ISP, and obtain all necessary information from them.

Broadband

3G/3.5G

Cable Modem

Fixed-IP Xdsl

PPPoE xDSL

PPTP xDSL

L2TP XDSL

Telstra Big Pond This option is for Australia only. Please refer to section 4.2.7 8 for details.

Description

With 3G mobile USB adapter providing Internet service. Please refer to section 4.2.1 for details. ISP will automatically give you an IP address. Please refer to section

4.2.2 for details. ISP has given you a fixed IP address already. Please refer to section

4.2.3 for details. ISP requires you to use a Point-to-Point Protocol over Ethernet (PPPoE) connection. Please refer to section 4.2.4 for details. ISP requires you to use a Point-to-Point Tunneling Protocol (PPTP) connection. Please refer to section 4.2.5 for details. This is not widely used. You need to know the PPTP Server address as well as your name and password. Please refer to section 4.2.6 for details.

4.2.1 3G/3.5G

With 3G mobile USB adapter providing Internet service. Some ISP may also require you to fill in additional information.

Parameters Description

Please input Pin Code for your UMTS or HSDPA or EVDO connection, this is option al,

PIN Code

and only required if your service provider asks you to do so. APN User Name Please input user name assigned by your Internet service provider here. Password Password Please input password again for confirmation. Verify Password Please input password again for confirmation. APN Please input the APN code assigned by your Internet service provider here. Service Please select your Card type from the drop-down menu.

Please input Dialed Number for your UMTS or HSDPA connectio n, the default is *99#. AT Dial Script

This field should not be altered except when required by your service provider.

4.2.2 Cable Modem

With Cable Modem connection, the ISP will automatically give you an IP address. Some ISP may also require you to fill in additional information such as Host Name and MAC address (see screen b elow).

Note: The Host Name and MAC address section is optional and you can skip this section if your ISP does not require these settings for you to connect to the Internet.

Parameters Description

Host Name Type in the host name provided by your ISP if any; otherwise, just leave it blank.

To connect to Internet, your ISP will require a MAC address from your PC. Type in this MAC Address

When the configuration finished, click “OK” to next step or click “Back” to previous step. After press “OK”, you will see a web screen to prompt you the confi gurations save successfully. You may press “Apply” to restart WNRT-625G with new configuration. Please refer to section 4.2.7 for more information about this screen.

MAC address in this section or use the “Clone MAC Address” button to replace the

WAN port MAC address with the your PC’s.

4.2.3 Fixed-IP xDSL

Select Fixed-IP xDSL if you’re ISP has given you a specified IP address. Your ISP should provide all the information required in this section.

Parameters Description

IP address assigned by your Service Provider Subnet Mask Enter the Subnet Mask provided by your ISP (e.g. 255.255.255.0). DNS Address The IP address of ISP’s DNS (Domain Name Service) Server. Service Provider Gateway Address

Please consult your local ISP about the information above. When the configuration finished please click “OK” to next step or click “Back” to previous step. After press “OK”, you will see a web screen to prompt you the configurations save successfully. Please refer to section 4.2.7 for the information of this screen.

The IP address that you’re ISP should provide you.

The ISP’s IP address gateway.

4.2.4 PPPoE xDSL

Select PPPoE if your ISP requires the PPPoE protocol for Internet connectivity. Your ISP should provide all the information like user name, password required in this section.

Parameters Description

User Name Enter the User Name provided by your ISP for the PPPoE connection. Password Enter the Password provided by your ISP for the PPPoE connection. Service Name This is an optional parameter. Leave it blank unless your ISP requires it.

This is an optional parameter. You can specif y the maximum size of transmission

MTU

packet to the Internet. The range of the MTU will be from 512 to 1492. You can also consult you ISP for the optimal MTU as well. Default: 1392.

If you select “Continuous”, the router will always connect to the ISP. If the WAN line breaks down and links again, the router wills auto-reconnect to the ISP. If you select “Connect On Demand”, the router will auto-connect to the ISP when a client in LAN want to use the Internet and keep connected until the WAN idle

Connection Type

Idle Time

timeout. The router will close the WAN connection if the time period that no one is using the Internet exceeds the “Idle Time”. If you select “Manual”, the router will connect to ISP only when you click “Connect” manually from the Web user interface. The WAN connection will not disconnected due to the idle timeout. If the WAN line breaks down and latter links again, the router will not auto-connect to the ISP. Default: Continuous. You can specify an idle time threshold (minutes) for the WAN port. This means if no packets have been sent (no one using the Internet) during this specified period, the router will automatically disconnect the connection from your ISP. Note: This “idle timeout” function may not work due to abnormal activities of some network application software, computer virus or hacker attacks from the Internet. For example, some software sends network packets to the Internet in the background, even when you are not using the Internet. So please turn off your computer when you are not using it. This function also may not work with some ISP. So please make sure this function can work properly, especially when your ISP charges you by time used.

When the configuration finished, click “Apply” to next step or click “Cancel” to previous step. After press “Apply”, you will see a web screen to prompt you the configurations save successfully. Please refer to section 4.2.7 for the information of this screen.

4.2.5 PPTP xDSL

Select PPTP if your ISP requires the PPTP protocol to connect to the Internet. Your ISP should provide all the information required in this section.

Parameter Description

Obtain an IP address Select it if the ISP requires you to obtain an IP address by DHCP automatically. Host Name Type in the host name provided by your ISP if any; otherwise, just leave it blank.

To connect to the Intern et, your ISP will require a MAC address from your PC.

MAC Address

Use the following IP address

IP Address

Subnet Mask Enter the Subnet Mask provided by your ISP (e.g. 255.255.255.0) Gateway Enter the IP address of the ISP’s Gateway.

User ID

Password Enter the Password provided by your ISP for the PPTP connection

PPTP Gateway

Type in this MAC address in this section or use the “Clone MAC Address” button to replace the WAN port MAC address with the MAC address of that PC. Select it if the ISP provides you a static IP to connect to the PPTP server.

This is the IP address that your ISP has given you to establish a PPTP connection.

Enter the User Name provided by your ISP for the PPTP connection. Sometimes called a Connection ID.

If your LAN has a PPTP gateway, enter that PPTP gateway’ s IP address here. If you do not have a PPTP gateway, enter the ISP’s Gateway IP address above.

Connection ID This is the ID given by ISP. This is an optional parameter.

This is an optional parameter. You can specify the maximum size of

MTU

BEZEQ-ISRAEL Select this item if you are using the service provided by BEZEQ in Israel.

Connection Type

transmission packet to the Internet. The range of the MTU will be from 512 to

1492. You can also consult you ISP for the optimal MTU as well. Default: 1392

If you select “Continuous”, the router will always connect to the ISP. If the WAN line breaks down and links again, the router shall auto- reconnect to the ISP.

If you select “Connect On Demand”, the router will auto-connect to the ISP when a client in LAN wants to use the Internet and keep connected until the WAN idle timeout. The router will close the WAN connection if the time period that no one is using the Internet exceeds the “Idle Time”. If you select “Manual”, the router will connect to ISP only when you click “Connect” manually from the Web user interface. The WAN connection will not disconnect due to the idle timeout. If the WAN line breaks down and latter links again, the router will not auto-connect to the ISP. Default: Continuous. You can specify an idle time threshold (minutes) for the WAN port. This means if no packets have been sent (no one using the Internet) throughout this specified period, the router will automatically disconnect to with your ISP. Note: This “idle timeout” function may not work due to abnormal activiti es of

Idle Time

When the configuration finished please click “OK” to next step or click “Back” to previous step. After press “OK”, you will see a web screen to prompt you the configurations save successfully. Please refer to section 4.2.7 for the information of this screen.

some network application software, computer virus or hacker attacks from the Internet. For example, some software sends network packets to the Internet in the background, even when you are not using the Internet. So please turn off your computer when you are not using it. This function also may not work with some ISP. So please make sure this function can work properly, especially when your ISP charges you by time used.

4.2.6 L2TP xDSL

Select L2TP if your ISP requires the L2TP protocol to connect to the Internet. Your ISP should provide all the information required in this section.

Parameter Description

Obtain an IP address Select it if the ISP requires you to obtain an IP address by DHCP automatically.

Host Name

MAC Address

Use the following IP address

IP Address

Subnet Mask Enter the Subnet Mask provided by your ISP (e.g. 255.255.255.0) Gateway Enter the IP address of the ISP’s Gateway.

User ID

Password Enter the Password provided by your ISP for the L2TP connection

If your ISP requires a Host Name, type in the host name provided by your ISP; otherwise, just leave it blank. To connect to the Intern et, your ISP will require a MAC address from your PC. Type in this MAC address in this section or use the “Clone MAC Address” button to replace the WAN port MAC address with the MAC address of that PC. Select it if the ISP provides you a static IP to connect to the L2TP server.

This is the IP address that your ISP has given you to establish a L2TP connection.

Enter the User Name provided by your ISP for the L2TP connection. Sometimes called a Connection ID.

L2TP Gateway

MTU

Connection Type

If your LAN has a L2TP gateway, enter that L2TP gateway’s IP address here. If you do not have a L2TP gateway, enter the ISP’s Gateway IP address above. This is an optional parameter. You can specify the maximum size of transmission packet to the Internet. The range of the MTU will be from 1492 to

512. You ca n also consult you ISP for the optimal MTU as well. Default: 1392 If you select “Continuous”, the router will always connect to the ISP. If the WAN

line breaks down and links again, the router shall auto- reconnect to the ISP. If you select “Connect On Demand”, the router will auto-connect to the ISP when someone wants to use the Internet and keep connected until the WAN idle timeout. The router will close the WAN connection if the time period that no one is using the Internet exceeds the “Idle Time”. If you select “Manual”, the router will connect to ISP only when you click “Connect” manually from the Web user interface. The WAN connection will not disconnect due to the idle timeout. If the WAN line breaks down and latter links again, the router will not auto-connect to the ISP. Default: Continuous. You can specify an idle time threshold (minutes) for the WAN port. This means if no packets have been sent (no one using the Internet) throughout this specified period, then the router will automatically disconnect the connection with your ISP. Note: This “idle timeout” function may not work due to abnormal activities of

Idle Time

4.2.7 Telstra Big Pond

Select Telstra Big Po nd if you are liv e in Australia and yo ur ISP requires this protocol to conn ect to th e Internet. Your I SP should prov ide all the information required in this section.

+ 56 hidden pages

Planet WNRT-625G User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Chapter 1 Introduction

1.1 Package Contents

1.2 Features

1.3 Specification

Chapter 2 Hardware Installation / Network Setup

2.1 Outlook

2.2 Hardware Installation

2.3 Network Setup

Chapter 3 Web Login

Chapter 4 Quick Setup

4.1 Time Zone

4.2 WAN Type

4.2.1 3G/3.5G

4.2.2 Cable Modem

4.2.3 Fixed-IP xDSL

4.2.4 PPPoE xDSL

4.2.5 PPTP xDSL

4.2.6 L2TP xDSL

4.2.7 Telstra Big Pond