PLANET WNAP-7335 User Manual

Copyright

Copyright  2015 by PLANET Technology Corp. All rights reserved. No part of this publication may
be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language
or computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of PLANET.

PLANET makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular
purpose. Any software described in this manual is sold or licensed "as is". Should the programs
prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer)
assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software. Further, this company reserves the right to revise
this publication and to make changes from time to time in the contents hereof without obligation to
notify any person of such revision or changes.

All brand and product names mentioned in this manual are trademarks and/or registered trademarks
of their respective holders.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digit

pursuan

t to part 15 of the FCC Rules. These limits are designed to provide reasonable

al device,

protection against harmful interference when the equipment is operated in a commercial

environme

nt. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his/her own
expense. Any changes or modifications not expressly approved by PLANET could void the user’s
authority to operate this equipment under the rules and regulations of the FCC.

FCC Caution:

To assure continued compliance, (for example, use only shielded interface cables when connecting
to computer or peripheral devices) any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:

(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause

undesired operation.

Federal Communication Commission (FCC) Radiation Exposure Statement

This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity
to the antenna shall not be less than 20 cm (8 inches) during normal operation.

I

CE Mark Warning

This is a Class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.

Energy Saving Note of the Device

This power required device does not support Standby mode operation. For energy saving, please
remove the DC-plug to disconnect the device from the power circuit. Without removing the DC-plug,
the device still consumes power from the power circuit. In view of Saving the Energy, it is strongly
suggested to remove the DC-plug for the device if this device is not intended to be active.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication
terminal Equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive
repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and
Satellite Earth Station Equipment) as of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity when
working with electrical equipment. All guidelines of this and of the computer manufacture must
therefore be allowed at all times to ensure the safe use of the equipment.

WEEE regulation

To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users of
electrical and electronic equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and thus,
WEEE has to be collected separately.

II

Revision

User’s Manual of PLANET 802.11a/n Outdoor Wireless CPE

Model: WNAP-7325 / WNAP-7335

Rev: 1.0 (May, 2015)

Part No. EM-WNAP-7325_v1.0 (2081-E10580-000) / EM-WNAP-7335_v1.0 (2081-E10610-000)

III

CONTENTS

Chapter 1. Product Introduction...........................................................................................................8

1.1 Package Contents...............................................................................................................8

1.2 Product Description............................................................................................................ 9

1.3 Product Features............................................................................................................... 10

1.4 Product Specifications ..................................................................................................... 11

Chapter 2. Hardware Installation ........................................................................................................14

2.1 Hardware Description.......................................................................................................14

2.1.1 The Bottom Panel – Port ........................................................................................15

Chapter 3. Connecting to the AP........................................................................................................18

3.1 Preparation before Installation ........................................................................................18

3.1.1 Professional Installation Required..........................................................................18

3.1.2 Safety Precautions.................................................................................................. 18

3.2 Installation Precautions....................................................................................................18

3.3 Installing the AP ................................................................................................................20

3.4 Standard Pole Mounting................................................................................................... 22

Chapter 4. Quick Installation Guide ................................................................................................... 23

4.1 Manual Network Setup - TCP/IP Configuration..............................................................23

4.1.1 Configuring the IP Address Manually .....................................................................23

4.2 Starting Setup in the Web UI ............................................................................................ 26

Chapter 5. Configuring the AP............................................................................................................ 29

5.1 Operation Modes...............................................................................................................29

5.1.1 Access Point...........................................................................................................30

5.1.2 Client.......................................................................................................................32

5.1.3 WDS AP..................................................................................................................34

5.1.4 WDS Client .............................................................................................................35

5.1.5 AP Router ...............................................................................................................36

5.1.6 Wireless ISP ...........................................................................................................37

5.1.7 Security Setting....................................................................................................... 38

5.1.8 Advanced Settings..................................................................................................43

5.1.9 Access Control........................................................................................................46

5.1.10 WAN Port Settings..................................................................................................47

5.1.11 Dynamic DNS Settings ........................................................................................... 49

5.1.12 Remote Management .............................................................................................53

5.1.13 DHCP Server Settings............................................................................................54

5.1.14 DMZ Settings ..........................................................................................................54

5.1.15 Virtual Server Settings............................................................................................55

5.1.16 IP Filtering Settings.................................................................................................55

5.1.17 Port Filtering Settings .............................................................................................56

IV

5.1.18 MAC Filtering Settings............................................................................................57

5.1.19 Bandwidth Control ..................................................................................................57

5.1.20 SNMP......................................................................................................................58

5.2 System Configuration....................................................................................................... 59

5.2.1 Default IP Settings ..................................................................................................59

5.2.2 Time Settings..........................................................................................................60

5.2.3 Password Settings ..................................................................................................61

5.2.4 System Management..............................................................................................61

5.2.5 Ping Watchdog........................................................................................................62

5.2.6 Firmware Upgrade..................................................................................................63

5.2.7 Configuration Save and Restore ............................................................................64

5.2.8 Factory Default .......................................................................................................64

5.2.9 Reboot System .......................................................................................................65

5.2.10 Schedule Reboot .................................................................................................... 65

5.3 Tools ................................................................................................................................... 67

5.3.1 Network Ping ..........................................................................................................67

5.3.2 Network Traceroute ................................................................................................67

5.4 Device Status..................................................................................................................... 69

5.4.1 Device Information..................................................................................................70

5.4.2 Wireless Information ...............................................................................................71

5.4.3 LAN Information......................................................................................................72

5.4.4 Wireless Client Table .............................................................................................. 73

5.4.5 System Log.............................................................................................................74

5.5 Logout ................................................................................................................................74

Appendix A: Troubleshooting............................................................................................................ 76

Appendix B: Use Planet Smart Discovery to find AP......................................................................78

Appendix C: FAQ.................................................................................................................................79

Q1: How to set up the AP Client Connection........................................................................... 79

Q2: How to set up the WDS Connection .................................................................................. 87

V

FIGURES

FIGURE 2-1 THREE-WAY VIEW..............................................................................................................................14

FIGURE 2-2 LED...................................................................................................................................................15

FIGURE 2-3 WNAP-7325 BOTTOM PANEL............................................................................................................16

FIGURE 2-4 WNAP-7335 BOTTOM PANEL............................................................................................................16

FIGURE 2-5 POE INJECTOR ...................................................................................................................................16

FIGURE 3-1 CONNECT THE ANTENNA ...................................................................................................................20

FIGURE 3-2 WNAP-7325 CONNECT THE ETHERNET CABLE .................................................................................20

FIGURE 3-3 WNAP-7335 CONNECT THE ETHERNET CABLE .................................................................................20

FIGURE 3-4 CONNECT THE POE INJECTOR ............................................................................................................21

FIGURE 3-5 CONNECT THE POE INJECTOR ............................................................................................................21

FIGURE 3-6 WNAP-7325 POLE MOUNTING .........................................................................................................22

FIGURE 3-7 WNAP-7335 POLE MOUNTING .........................................................................................................22

FIGURE 4-1 TCP/IP SETTING................................................................................................................................24

FIGURE 4-2 WINDOWS START MENU....................................................................................................................25

FIGURE 4-3 SUCCESSFUL RESULT OF PING COMMAND ..........................................................................................25

FIGURE 4-4 FAILED RESULT OF PING COMMAND ...................................................................................................26

FIGURE 4-5 LOGIN BY DEFAULT IP ADDRESS.........................................................................................................26

FIGURE 4-6 LOGIN WINDOW ................................................................................................................................27

FIGURE 4-7 WEB UI SCREENSHOT........................................................................................................................27

FIGURE 4-8 CHOOSE OPERATION MODE ...............................................................................................................28

FIGURE 4-9 CONFIGURE WIRELESS SETTINGS ......................................................................................................28

FIGURE 5-1 MAIN MENU ......................................................................................................................................29

FIGURE 5-2 OPERATION MODES ...........................................................................................................................29

FIGURE 5-3 BASIC SETTINGS - AP ........................................................................................................................30

FIGURE 5-4 BASIC SETTINGS - CLIENT .................................................................................................................32

FIGURE 5-5 BASIC SETTINGS – WDS AP..............................................................................................................34

FIGURE 5-6 BASIC SETTINGS – WDS CLIENT.......................................................................................................35

FIGURE 5-7 BASIC SETTINGS – AP ROUTER..........................................................................................................36

FIGURE 5-8 BASIC SETTINGS – WISP...................................................................................................................38

FIGURE 5-9 SECURITY SETTINGS ..........................................................................................................................38

FIGURE 5-10 SECURITY SETTINGS – WEP ............................................................................................................39

FIGURE 5-11 SECURITY SETTINGS – WPA PERSONAL...........................................................................................39

FIGURE 5-12 SECURITY SETTINGS – WPA ENTERPRISE ........................................................................................40

FIGURE 5-13 SECURITY SETTINGS – WPA2 PERSONAL.........................................................................................41

FIGURE 5-14 SECURITY SETTINGS – WPA2 ENTERPRISE......................................................................................41

FIGURE 5-15 SECURITY SETTINGS – WPA-MIXED PERSONAL ..............................................................................42

FIGURE 5-16 SECURITY SETTINGS – WPA-MIXED ENTERPRISE............................................................................42

FIGURE 5-17 ADVANCED SETTINGS ......................................................................................................................43

FIGURE 5-18 WMM CONFIGURATION ..................................................................................................................44

FIGURE 5-19 ACCESS CONTROL............................................................................................................................46

FIGURE 5-20 WAN PORT SETTINGS – DHCP........................................................................................................47

FIGURE 5-21 WAN PORT SETTINGS – STATIC IP...................................................................................................47

FIGURE 5-22 WAN PORT SETTINGS – PPPOE ......................................................................................................48

VI VII

FIGURE 5-23 DYNAMIC DNS SETTINGS................................................................................................................49

FIGURE 5-24 REMOTE MANAGEMENT ..................................................................................................................53

FIGURE 5-25 DHCP SERVER SETTINGS ................................................................................................................54

FIGURE 5-26 DMZ SETTINGS ...............................................................................................................................54

FIGURE 5-27 VIRTUAL SERVER SETTINGS.............................................................................................................55

FIGURE 5-28 IP FILTERING SETTINGS ...................................................................................................................56

FIGURE 5-29 PORT FILTERING SETTINGS ..............................................................................................................56

FIGURE 5-30 MAC FILTERING SETTINGS...............................................................................................................57

FIGURE 5-31 BANDWIDTH CONTROL SETTINGS....................................................................................................57

FIGURE 5-32 SNMP SETTINGS .............................................................................................................................58

FIGURE 5-33 SYSTEM CONFIGURATION DEFAULT PAGE.........................................................................................59

FIGURE 5-34 DEFAULT IP SETTINGS .....................................................................................................................59

FIGURE 5-35 TIME SETTINGS................................................................................................................................60

FIGURE 5-36 PASSWORD SETTINGS.......................................................................................................................61

FIGURE 5-37 SYSTEM MANAGEMENT...................................................................................................................62

FIGURE 5-38 PING WATCHDOG .............................................................................................................................63

FIGURE 5-39 FIRMWARE UPGRADE.......................................................................................................................63

FIGURE 5-40 CONFIGURATION SAVE AND RESTORE..............................................................................................64

FIGURE 5-41 FACTORY DEFAULT ..........................................................................................................................64

FIGURE 5-42 REBOOT SYSTEM .............................................................................................................................65

FIGURE 5-43 SCHEDULE REBOOT .........................................................................................................................65

FIGURE 5-44 SCHEDULE REBOOT - EXAMPLE.......................................................................................................66

FIGURE 5-45 NETWORK PING ...............................................................................................................................67

FIGURE 5-46 NETWORK TRACEROUTE..................................................................................................................68

FIGURE 5-47 DEVICE STATUS ...............................................................................................................................69

FIGURE 5-48 DEVICE INFORMATION .....................................................................................................................70

FIGURE 5-49 WIRELESS INFORMATION .................................................................................................................71

FIGURE 5-50 LAN INFORMATION .........................................................................................................................72

FIGURE 5-51 WIRELESS CLIENT TABLE ................................................................................................................73

FIGURE 5-52 SYSTEM LOG ...................................................................................................................................74

FIGURE 5-53 LOGOUT...........................................................................................................................................74

FIGURE 5-54 RE-LOGIN ........................................................................................................................................75

User Manual of WNAP-7325/WNAP-7335

Chapter 1. Product Introduction

1.1 Package Contents

Thank you for choosing PLANET WNAP-7325 series. Before installing the AP, please verify the contents inside

the package box.

WNAP-7325 / WNAP-7335 Quick Installation Guide

PoE Injector & Power Cord Plastic Strap x 1

If there is any item missing or damaged, please contact the seller

immediately.

-8-

User Manual of WNAP-7325/WNAP-7335

1.2 Product Description

PLANET WNAP-7325/WNAP-7335 Outdoor Wireless Access Point provides a higher transmission speed,
higher power and better performance designed for outdoor wireless application.

Faster Speed and longer Distance

Adopting the IEEE 802.11n advanced 2T2R MIMO technology, the WNAP-7325 and WNAP-7335 provide high
speed, reliable wireless network coverage, and incredible improvement in the wireless performance. As an IEEE

802.11a/n compliant wireless device, the WNAP-7325 and WNAP-7335 are able to give stable and efficient
wireless performance for long distance application. Thus, it delivers a data rate of up to 300Mbps three times
faster than the normal 802.11a wireless device. With its adjustable output power up to 500mW, it can extend the
coverage of an outdoor area.

Multiple Operation and Wireless Modes

The WNAP-7325 and WNAP-7335 support multiple wireless communication connectivities (AP, Client CPE,
WDS PtP, WDS PtMP and WISP), meeting user’s application requirements. It also helps user to easily extend
the existing wireless network.

Advanced Wireless Security

In aspect of security, besides 64/128- bit WEP encryption, the WNAP-7325 and WNAP-7335 are integrated with
WPA / WPA2, WPA-PSK / WPA2-PSK and 802.1x RADIUS authentication to secure and protect your wireless
LAN. The wireless MAC filtering and SSID broadcast help to consolidate the wireless network security and
prevent unauthorized wireless connection.

Perfect Solution for Outdoor Environment

The WNAP-7325 and WNAP-7335 are perfectly suitable to be installed in outdoor environments. With its IP55
casing protection, the WNAP-7325 and WNAP-7335 can perform normally under rigorous weather conditions
including heavy rain and wind. With the passive Power over Ethernet (PoE) design, the WNAP-7325 and
WNAP-7335 can be easily installed in the areas where power outlets are not available. Thus, the WNAP-7325
and WNAP-7335 are ideal for outdoor wireless access applications between buildings on campuses, and in
business and rural areas.

Easy Installation and Management

With user-friendly Web UI and step by step Setup Wizard, user can set up a wireless network without any
difficulty.

-9-

1.3 Product Features

 Industrial Compliant Wireless LAN & LAN

 Compliant with the IEEE 802.11n wireless technology (with data rate of up to 300Mbps)

 Backward compatible with 802.11a standard

 Equipped with 10/100Mbps RJ45 ports for LAN & WAN; auto MDI/ MDI-X supported

 Fixed-network Broadband Router

 Supported connection types: Dynamic IP, Static IP, PPPoE

 Supports Virtual Server, DMZ for various networking applications

 Supports DHCP Server, UPnP, Dynamic DNS

 RF Interface Characteristics

 Built-in 14dBi Dual-Polarization Antenna (WNAP-7325)

 Built-in RP-SMA antenna connectors (WNAP-7335)

User Manual of WNAP-7325/WNAP-7335

 High Output Power Up to 500mW with multiple adjustable transmit power control

 Outdoor Environmental Characteristics

 IP55 enclosure

 Passive Power over Ethernet design

 Operating temperature: -20~70°C

 Multiple Operation and Wireless Modes

 Multiple operation modes: Bridge, WISP

 Multiple wireless modes: AP, Client CPE(WISP), WDS PtP, WDS PtMP

 Supports multiple SSIDs to allow users to access different networks through a single AP

 Supports WMM (Wi-Fi multimedia)

 Secure Network Connection

 Supports software Wi-Fi Protected Setup (WPS)

 Advanced security: 64/128-bit WEP, WPA/WPA2, WPA-PSK/WPA2-PSK(TKIP/AES) and 802.1x

authentication

 Supports IP / Protocol-based access control and MAC filtering

 Easy Installation and Management

 Web-based UI and quick Setup Wizard for easy configuration

 SNMP-based management interface

 System status monitoring includes DHCP Client, System Log

-10-

1.4 Product Specifications

User Manual of WNAP-7325/WNAP-7335

Product

Hardware

Standard Support

Chipset

Memory

PoE

Interface

Antenna

WNAP-7325 WNAP-7335

300Mbps 802.11a/n Wireless Outdoor CPE

IEEE802.11a/n
IEEE 802.3
IEEE 802.3u
IEEE 802.3x

Atheros AR9344

64 Mbytes DDR SDRAM
16 Mbytes Flash

Passive PoE

Wireless IEEE802.11a/n, 2T2R
PoE LAN (LAN 1): 1 x 10/100BASE-TX, auto-MDI/MDIX, passive PoE
LAN 2: 1 x 10/100BASE-TX, auto-MDI/MDIX, passive PoE out pass-through

Built-in 14dBi Dual-Polarization
Antenna

Built-in RP-SMA antenna connectors

- Vertical: 20 degrees

- Horizontal: 30 degrees

Data Rate

Media Access Control

Modulation

Frequency Band

Operating Channel

IEEE 802.11a: 6, 9, 12, 18, 24, 36, 48, 54Mbps
IEEE 802.11n (20MHz): up to 150Mbps
IEEE 802.11n (40MHz): up to 300Mbp

CSMA/CA

Transmission/Emission type: OFDM
Data modulation type: OFDM with BPSK, QPSK, 16-QAM, 64-QAM

5.180GHz ~ 5.825GHz

5.180GHz CH36 5.580GHz CH116

5.200GHz CH40 5.600GHz CH120

5.220GHz CH44 5.620GHz CH124

5.240GHz CH48 5.640GHz CH128

5.260GHz CH52 5.660GHz CH132

5.280GHz CH56 5.680GHz CH136

5.300GHz CH60 5.700GHz CH140

5.320GHz CH64 5.745GHz CH149

5.500GHz CH100 5.765GHz CH153

5.520GHz CH104 5.785GHz CH157

5.540GHz CH108 5.805GHz CH161

5.560GHz CH112 5.825GHz CH165
*The 24 channels are defined by the theory. The actual application will vary
based on the regulation in different regions and countries.

-11-

User Manual of WNAP-7325/WNAP-7335

RF Output Power (dBm)

Receiver Sensitivity

(dBm)

Output Power Control

Power Consumption

Power Requirements

Environment & Certification

Operating Temperature

Operating Humidity

IP Level

Regulatory

Software

802.11a: up to 26 ± 1

802.11n: up to 25 ± 1

802.11a: -94dBm

802.11n: -93dBm

12~27dBm

12W

LAN 24VDC, 1A/ Passive PoE

Pin 4,5 VDC+
Pin 7,8 VDC­Pin 3 Reset

-20~70°c

10~95% non-condensing

IP55

CE, FCC, RoHS

LAN

WAN

Operation Modes

Firewall

Wireless Modes

Channel Width

Wireless Isolation

Built-in DHCP server supporting static IP address distribution
Support 802.1d STP (Spanning Tree)

 Static IP
 Dynamic IP

 PPPoE

 Bridge
 WISP

NAT firewall with SPI (Stateful Packet Inspection)
Built-in NAT server supporting Virtual Server, and DMZ
Built-in firewall with Port/ IP address/ MAC/ URL filtering

 AP
 Client
 WDS PTP
 WDS PTMP
 WISP

20MHz / 40MHz

Enable it to isolate each connected wireless client so that they cannot access
mutually.

Encryption Type

Wireless Security

Max. Wireless Clients

Max. WDS Peers
Max. Wired Clients

64/128-bit WEP, WPA, WPA-PSK, WPA2, WPA2-PSK, 802.1X

Provides wireless LAN ACL (Access Control List) filtering
Wireless MAC address filtering
Enable/Disable SSID Broadcast

25

8

60

-12-

User Manual of WNAP-7325/WNAP-7335

Chapter 1. Product Introduction

1.1 Package Contents

Thank you for choosing PLANET WNAP-7325 series. Before installing the AP, please verify the contents inside

the package box.

WNAP-7325 / WNAP-7335 Quick Installation Guide

PoE Injector & Power Cord Plastic Strap x 1

If there is any item missing or damaged, please contact the seller

immediately.

-8-

User Manual of WNAP-7325/WNAP-7335

Chapter 2. Hardware Installation

Please follow the instructions below to connect the WNAP-7325 and WNAP-7335 to the existing network
devices and your computers.

2.1 Hardware Description

 Dimensions: 127 x 63 x 254 mm (W x D x H)

Appearance

Figure 2-1 Three-way View

-14-

Rear Panel – LED

User Manual of WNAP-7325/WNAP-7335

Figure 2-2 LED

LED Definition

LED State Meaning

On System On

Power

Off System Off

Signal Indicator

(Client Mode)

On Indicates the wireless signal strength of remote AP

Off No remote wireless signal

On Port linked.

LAN 1

Off No link.

On Port linked.

LAN 2

Off No link.

2.1.1 The Bottom Panel – Port

Table 2-1 The LED indication

The Bottom panel provides the physical connectors connected to the power adapter and any other network

device. Figure 2-3 shows the bottom panel of the WNAP-7325 and WNAP-7335.

-15-

Bottom Panel

User Manual of WNAP-7325/WNAP-7335

Figure 2-3 WNAP-7325 Bottom Panel

PoE Injector

Figure 2-4 WNAP-7335 Bo

ttom Panel

Reset Button

Figure 2-5 PoE Injector

-16-

H/W Interface Definition

Object Description

PoE LAN

(Passive PoE)

LAN 2

User Manual of WNAP-7325/WNAP-7335

10/100Mbps RJ45 port , auto MDI/ MDI-X and passive PoE supported

Connect LAN port to the PoE injector to power on the device.

Pin assignment:

Pin 4, 5 (+)

Pin 7, 8 (-)

Pin 3 (Reset)

10/100Mbps RJ45 port , auto MDI/ MDI-X

Connect this port to the network equipment.

※

When the option “Enable POE Pass Through” on the System
Management page is checked, the LAN2 can supply passive PoE power to the
second WNAP-7325 or WNAP-7335 through LAN 2.

Press the Reset button on the device or on the PoE injector over 5
seconds to return to factory default setting.

Reset

※ If you have connected with the ELA-100, please DO NOT press the

reset button on the PoE injector to prevent the ELA-100 from being

damaged.

Table 2-2 The PoE Injector Indication

-17-

User Manual of WNAP-7325/WNAP-7335

Chapter 3. Connecting to the AP

3.1 Preparation before Installation

3.1.1 Professional Installation Required

Please seek assistance from a professional installer who is well trained in the RF installation and knowledgeable

in the local regulations.

3.1.2 Safety Precautions

1. To keep you safe and install the hardware properly, please read and follow these safety precautions.

2. If you are installing the WNAP-7325 or WNAP-7335 for the first time, for your safety as well as others’,
please seek assistance from a professional installer who has received safety training on the hazards
involved.

3. Keep safety as well as performance in mind when selecting your installation site, especially where there
are electric power and phone lines.

4. When installing the WNAP-7325 or WNAP-7335, please note the following things:

 Do not use a metal ladder;
 Do not work on a wet or windy day;
 Wear shoes with rubber soles and heels, rubber gloves, long sleeved shirt or jacket.

5. When the system is operational, avoid standing directly in front of it. Strong RF fields are present when the
transmitter is on.

3.2 Installation Precautions

 Users MUST use a proper and well-installed surge arrestor and grounding kit with the WNAP-7325 or

WNAP-7335; otherwise, a random lightning could easily cause fatal damage to the WNAP-7325 or

WNAP-7335. EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.

 Users MUST use the “Power cord and PoE Injector” shipped in the box with the WNAP-7325 or

WNAP-7335. Use of other options will cause damage to the WNAP-7325 or WNAP-7335.

-18-

User Manual of WNAP-7325/WNAP-7335

OUTDOOR INSTALLATION WARNING

!

IMPORTANT SAFETY PRECAUTIONS:

LIVES MAY BE AT RISK! Carefully observe these instructions and any special instructions that are included with the

equipment you are installing.

CONTACTING POWER LINES CAN BE LETHAL. Make sure no power

lines are anywhere where possible contact can be made. Antennas, masts,

towers, guy wires or cables may lean or fall and contact these lines. People

may be injured or killed if they are touching or holding any part of

equipment when it contacts electric lines. Make sure that equipment or

personnel do not come in contact directly or indirectly with power lines.

The horizontal distance from a tower, mast or antenna to the nearest

power line should be at least twice the total length of the mast/antenna combination. This will ensure that the mast will not

contact power if it falls either during installation or later.

TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS ABOVE GROUND.

 Select equipment locations that will allow safe, simple equipment installation.

 Don’t work alone. A friend or co-worker can save your life if an accident happens.

 Use approved non-conducting lasers and other safety equipment. Make sure all equipment is in good repair.

 If a tower or mast begins falling, don’t attempt to catch it. Stand back and let it fall.

 If anything such as a wire or mast does come in contact with a power line, DON’T TOUCH IT OR ATTEMPT TO

MOVE IT. Instead, save your life by calling the power company.

 Don’t attempt to erect antennas or towers on windy days.

MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND ELECTRICAL CABLES CONNECTED TO

ANTENNAS HAVE LIGHTNING ARRESTORS. This will help prevent fire damage or human injury in case of lightning, static

build-up, or short circuit within equipment connected to the antenna.

 The base of the antenna mast or tower must be connected directly to the building protective ground or to one or more

approved grounding rods, using 1 OAWG ground wire and corrosion-resistant connectors.

 Refer to the National Electrical Code for grounding details.

IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND CANNOT MOVE:

 DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.

 Use a non-conductive dry board, stick or rope to push or drag them so they no longer are in contact with electrical

power.

Once they are no longer contacting electrical power, administer CPR if you are certified, and make sure that emergency

medical aid has been requested.

-19-

User Manual of WNAP-7325/WNAP-7335

3.3 Installing the AP

Please install the AP according to the following steps. Don't forget to pull out the power plug and keep your

hands dry.

Step 1. Push the latch in the bottom of the WNAP-7325 or WNAP-7335 to remove the sliding cover.

Figure 3-1 Connect the Antenna

Step 2. Plug the RJ45 Ethernet cable into the PoE LAN Port of the WNAP-7325 or WNAP-7335. Connecting

the external antenna to the RP-SMA connectors if you are using the WNAP-7335.Then, slide back the
cover to finish the installation.

Figure 3-2 WNAP-7325 Connect the Ethernet cable

Figure 3-3 WNAP-7335 Connect the Ethernet cable

-20-

User Manual of WNAP-7325/WNAP-7335

Step 3. Plug the power cord into the DC port and the other end into the AC socket. Then, plug the RJ45 cable

(as shown in picture 4 under Step 1) into the POE port of the PoE injector.

Figure 3-4 Connect the PoE injector

Figure 3-5 Connect the PoE injector

-21-

User Manual of WNAP-7325/WNAP-7335

3.4 Standard Pole Mounting

Place the strap through the slots on the back of the WNAP-7325 or WNAP-7335 and then around the pole.
Tighten the strap to secure the WNAP-7325 or WNAP-7335.

Figure 3-6 WNAP-7325 Pole Mounting

Figure 3-7 WNAP-7335 Pole Mounting

-22-

User Manual of WNAP-7325/WNAP-7335

Chapter 4. Quick Installation Guide

This chapter will show you how to configure the basic functions of your AP within minutes.

A computer with wired Ethernet connection to the Wireless AP is required for the first-time

configuration.

4.1 Manual Network Setup - TCP/IP Configuration

The default IP address of the WNAP-7325 and WNAP-7335 is 192.168.1.253. And the default Subnet Mask is

255.255.255.0. These values can be changed as you desire. In this guide, we use all the default values for

description.

Connect the WNAP-7325 or WNAP-7335 with your PC via an Ethernet cable which is then plugged into a LAN

port of the PoE injector with one end and into a LAN port of the PC with the other end. Then power on the

WNAP-7325 or WNAP-7335 via PoE injector or PoE switch.

In the following sections, we’ll introduce how to install and configure the TCP/IP correctly in Windows 7. And the
procedures in other operating systems are similar. First, make sure your Ethernet adapter is working, and refer
to the Ethernet adapter’s manual if needed.

4.1.1 Configuring the IP Address Manually

Summary:

 Set up the TCP/IP Protocol for your PC.

 Configure the network parameters. The IP address is 192.168.1.xxx ("xxx" is any number from 2 to

252), Subnet Mask is 255.255.255.0, and Gateway is 192.168.1.253 (The AP's default IP address)

1 Select Use the following IP address radio button.

2 If the AP's LAN IP address is 192.168.1.1, enter IP address 192.168.1.x (x is from 2 to 254), and Subnet

mask 255.255.255.0.

3 Select Use the following DNS server addresses radio button. In the Preferred DNS Server field, you can

enter the DNS server IP address which has been provided by your ISP

-23-

User Manual of WNAP-7325/WNAP-7335

Figure 4-1 TCP/IP Setting

Now click OK to save your settings.

Now, you can run the ping command in the command prompt to verify the network connection between your

PC and the AP. The following example is in Windows 7 OS. Please follow the steps below:

1. Click on Start > Run.

2. Type “cmd” in the Search box.

-24-

User Manual of WNAP-7325/WNAP-7335

Figure 4-2 Windows Start Menu

3. Open a command prompt and type ping 192.168.1.253, and then press Enter.

If the result displayed is similar to Figure 4-3, it means the connection between your PC and the AP

has been established well.

Figure 4-3 Successful result of Ping command

If the result displayed is similar to Figure 4-4, it means the connection between your PC and the AP

has failed.

-25-

User Manual of WNAP-7325/WNAP-7335

Figure 4-4 Failed result of Ping command

If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your AP. Some

firewall software programs may block a DHCP request on newly installed adapters.

4.2 Starting Setup in the Web UI

It is easy to configure and manage the WNAP-7325 or WNAP-7335 with the web browser.

Step 1. To access the configuration page, open a web browser and enter the default IP address

http://192.168.1.253 in the web address field of the browser.

Figure 4-5 Login by default IP address

After a moment, a login window will appear. Enter admin for the User Name and Password, both in lower case

letters. Then click the OK button or press the Enter key.

-26-

User Manual of WNAP-7325/WNAP-7335

Figure 4-6 Login Window

Default IP Address: 192.168.1.253

Default User Name: admin

Default Password: admin

If the above screen does not pop up, it may mean that your web browser has been set to a
proxy. Go to Tools menu>Internet Options>Connections>LAN Settings in the screen
that appears, cancel the Using Proxy checkbox, and click OK to finish it.

After entering the username and password, the Operation Mode page screen appears as in Figure 4-8

Figure 4-7 Web UI Screenshot

-27-

User Manual of WNAP-7325/WNAP-7335

Step 2. You can choose an Operation Mode. Please refer to the instructions in the next chapter for configuring

the other Operation Modes.

Figure 4-8 Choose Operation Mode

Step 3. Please enter the SSID and configure your Encryption Settings, Pre-Shared Key, etc. Then click the

Save button to make the configuration take effect immediately.

Figure 4-9 Configure Wireless Settings

-28-

User Manual of WNAP-7325/WNAP-7335

Chapter 5. Configuring the AP

This chapter delivers a detailed presentation of AP’s functionalities and features under 4 main menus
(Operation Mode, System Configuration, Tools and Device Status) below, allowing you to manage the AP
with ease.

Figure 5-1 Main Menu

5.1 Operation Modes

On this page, you can select different operation modes of the AP, including:

 Access Point
 Client
 WDS AP
 WDS Client
 AP Router
 Wireless ISP

Figure 5-2 Operation Modes

-29-

5.1.1 Access Point

User Manual of WNAP-7325/WNAP-7335

Click “Operation Mode”  “Access Point” and the following page will be displayed. This section allows you to

configure the Access Point mode.

Figure 5-3 Basic Settings - AP

Object Description

 Regulatory Domain

Select your domain from the list.

It is the wireless network name. The default SSID is WNAP-7325

 Network SSID

or WNAP-7335.

-30-

User Manual of WNAP-7325/WNAP-7335

 Site Survey

 Enable Wireless

 Disable SSID Broadcasting

Enable Isolated

Radio Mode

 Channel

 Data Rate

 Security Setting

 Transmit Power

Click “Site Survey” to check the signal of remote sites.

Check it to enable Wireless function.

Check it to disable SSID broadcasting.

Check it to isolate each connected wireless client so that they

cannot access each other.

Select the channel width to “Auto Select”, “5G 11NA HT20” or

“5G 11NA HT40”

Select the operating channel you would like to use. The channel

range will be changed by selecting a different domain.

Select MCS0~15 or Auto from the pull-down menu. The default is

“Auto”.

Press “Setup” for more configurations. Please refer to 5.1.7

Security Setting for more information.

The range of transmit power is “12~27 dbm”. In case of

shortening the distance and the coverage of the wireless

network, input a smaller value to reduce the radio transmission

 Transmit Distance

 TDMA

 Advanced Settings

 Access Control

power.

Select a specified distance of the two nodes.

Displays the System Time.

Press “Setup” for more configurations. Please refer to 5.1.8

Advanced Settings for more information.

Press “Setup” for more configurations. Please refer to 5.1.9

Access Control for more information.

-31-

5.1.2 Client

User Manual of WNAP-7325/WNAP-7335

Click “Operation Mode”  “Client” and the following page will be displayed. This section allows you to

configure the Client mode.

Figure 5-4 Basic Settings - Client

Object Description

 Regulatory Domain

Select your domain from the list.

It is the wireless network name. The default SSID is

 Network SSID

WNAP-7325 or WNAP-7335.

-32-

User Manual of WNAP-7325/WNAP-7335

 Site Survey

 Enable Wireless

 Disable SSID Broadcasting

Enable Isolated

Lock to AP MAC

Radio Mode

 Data Rate

 Security Setting

 Transmit Power

Click “Site Survey” to find the remote sites to associate.

Check it to enable Wireless function.

Check it to disable SSID broadcasting.

Check it to isolate each connected wireless clients so that they

cannot access each other.

Enter the Mac address of the remote AP.

Select the channel width to “Auto Select”, “5G 11NA HT20” or

“5G 11NA HT40”

Select MCS0~15 or Auto from the pull-down menu. The default

is “Auto”.

Press “Setup” for more configurations. Please refer to 5.1.7

Security Setting for more information.

The range of transmit power is “12~27 dbm”. In case of

shortening the distance and the coverage of the wireless

network, input a smaller value to reduce the radio transmission

 Transmit Distance

 TDMA

 Advanced Settings

 Access Control

power.

Select a specified distance of the two nodes.

Displays the System Time.

Press “Setup” for more configurations. Please refer to 5.1.8

Advanced Settings for more information.

Press “Setup” for more configurations. Please refer to 5.1.9

Access Control for more information.

-33-

5.1.3 WDS AP

User Manual of WNAP-7325/WNAP-7335

Click “Operation Mode”  “WDS AP” and the following page will be displayed. This section allows you to

configure the WDS AP mode. For each wireless parameter, please refer to section 5.1.1 AP for more

information.

Figure 5-5 Basic Settings – WDS AP

-34-

User Manual of WNAP-7325/WNAP-7335

5.1.4 WDS Client

Click “Operation Mode”  “WDS Client” and the following page will be displayed. This section allows you to

configure the WDS Client mode. For each wireless parameter, please refer to section 5.1.2 Client for more

information.

Figure 5-6 Basic Settings – WDS Client

-35-

User Manual of WNAP-7325/WNAP-7335

5.1.5 AP Router

Click “Operation Mode”  “AP Router” and the following page will be displayed. This section allows you to

configure the AP Router mode.

Figure 5-7 Basic Settings – AP Router

-36-

User Manual of WNAP-7325/WNAP-7335

5.1.6 Wireless ISP

Click “Operation Mode”  “Wireless ISP” and the following page will be displayed. This section allows you to

configure the Wireless ISP mode.

-37-

5.1.7 Security Setting

User Manual of WNAP-7325/WNAP-7335

Figure 5-8 Basic Settings – WISP

Choose the operation mode you required, and then enter “Security Setting” by clicking the Setup button next to

it and the following page will be displayed. This section allows you to configure the wireless security settings.

Figure 5-9 Security Settings

Object Description

Select the encryption that you need.

None: No security required

WEP: Input 5, 13 (ASCII) or 10, 26 (HEX) character for WEP

key.

 Select Encryption

WPA: Enter ASCII characters between 8 and 63 character or 8

to 64 hexadecimal characters.

WPA2: Enter ASCII characters between 8 and 63 character or

8 to 64 hexadecimal characters.

WPA-Mixed: Enter ASCII characters between 8 and 63

character or 8 to 64 hexadecimal characters.

-38-

User Manual of WNAP-7325/WNAP-7335

 None

Authentication is disabled and no password/key is required to connect to the access point.

 WEP

WEP (Wired Equivalent Privacy) is a basic encryption. For a higher level of security consider using the WPA

encryption.

Object Description

 Authentication

 Key Length

 Key Format

 Encryption Key

 WPA

Figure 5-10 Security Settings – WEP

You can select Open System, Shared Key or Auto.

Choose the WEP key length. You can choose 64-bit or 128-bit.

You can choose ASCII or Hex.

Enter the keys in the fields.

Figure 5-11 Security Settings – WPA Personal

-39-

User Manual of WNAP-7325/WNAP-7335

Figure 5-12 Security Settings – WPA Enterprise

Object Description

Select “Personal (Pre-Shared Key)” or “Enterprise (RADIUS)”

 Pre-Authentication

encryption type.

 Encryption Type

 Pre-Shared Key

Set the WPA to be TKIP, AES or Auto.

Enter the keys in the fields.

 RADIU Server IP

Enter the RADIUS server host IP address.

Address

Set the UDP port used in the authentication protocol of the RADIUS

 RADIU Server Port

server. Value must be between 1 and 65535.

 RADIU Server

Enter a shared secret/password between 1 and 99 characters in length.

Password

 EAP

Reauthorization

Set duration of session timeout in seconds between 300 and 3600.

Period

 RSN

Enable or disable RSN reauthorization.

Reauthorization

 WPA Group

Set duration of session timeout in seconds between 300 and 3600.

Re-key Interval

-40-

 WPA2
Please refer to WPA for more information.

Figure 5-13 Security Settings – WPA2 Personal

User Manual of WNAP-7325/WNAP-7335

Figure 5-14 Security Settings – WPA2 Enterprise

-41-

 WPA-Mixed
Please refer to WPA for more information.

Figure 5-15 Security Settings – WPA-Mixed Personal

User Manual of WNAP-7325/WNAP-7335

Figure 5-16 Security Settings – WPA-Mixed Enterprise

-42-

User Manual of WNAP-7325/WNAP-7335

5.1.8 Advanced Settings

Choose the operation mode you require, and then enter “Advanced Settings” by clicking the Setup button next

to it and the following page will be displayed. This section allows you to configure the wireless advanced

settings.

Figure 5-17 Advanced Settings

Object Description

When the length of a data packet exceeds this value, the router will send

 RTS/CTS

Threshold

an RTS frame to the destination wireless node, and the latter will reply
with a CTS frame, and thus they are ready to communicate. The default
value is 2347.
Set beacon interval, the value range is from 20 to 999. The default value

 Beacon Interval

is 100.
Set the DTIM (delivery traffic indication message) period value of the

 DTIM

wireless radio. The default value is 1.
A data packet that exceeds this value in length will be divided into

 Fragment Size

multiple packets. The number of packets influences wireless network
performance. Avoid setting this value low. Default at 2346.

-43-

User Manual of WNAP-7325/WNAP-7335

 Short GI

 Aggregation

 Aggregated

Frames Number

 Maximum

Aggregated Size

 Tx ChainMask

 Rx ChainMask

 WMM Capable

Guard intervals are used to ensure that distinct transmissions do not
interfere with one another. Only effect under Mixed Mode.
A part of the 802.11n standard that allows sending multiple frames per
single access to the medium by combining frames together into one
larger frame. It creates the larger frame by combining smaller frames
with the same physical source, destination end points, and traffic class
(QoS) into one large frame with a common MAC header
Determines the number of frames combined in the new larger frame.

Determines the size (in bytes) of the larger frame.

Displays the number of independent spatial data streams the device is
transmitting (TX) and receiving (RX) simultaneously within one spectral
channel of bandwidth. Multiple chains increase data transfer
performance significantly.
Displays the number of independent spatial data streams the device is
transmitting (TX) and receiving (RX) simultaneously within one spectral
channel of bandwidth. Multiple chains increase data transfer
performance significantly.
Wi-Fi Multimedia (WMM) is a Wi-Fi Alliance interoperability certification
based on the IEEE 802.11e standard, which provides Quality of Service
(QoS) features to IEE 802.11 networks. WMM prioritizes traffic
according to four categories: background, best effort, video and voice.

Figure 5-18 WMM Configuration

-44-

User Manual of WNAP-7325/WNAP-7335

WMM Capable

BE Traditional IP data, medium throughput and delay.

BK High throughput, non time sensitive bulk data e.g. FTP

VI Time sensitive video data with minimum time delay.

VO Time sensitive data such as VoIP and streaming media with

minimum time delay.

Aifsn Arbitration Inter-Frame Space (milliseconds): Specifies

additional time between when a channel goes idle and the

AP/client sends data frames. Traffic with a lower AIFSN

value has a higher priority.

CWMin Maximum Contention Window (milliseconds): This value is

the upper limit to random backoff value doubling (see

above).

CWMax Arbitration Inter-Frame Space (milliseconds): Specifies

additional time between when a channel goes idle and the

AP/client sends data frames. Traffic with a lower AIFSN

value has a higher priority.

Txop Transmission Opportunity (milliseconds): The maximum

interval of time an AP/client can transmit. This makes

channel access more efficiently prioritized. A value of 0

means only one frame per transmission. A greater value

effects higher priority.

-45-

User Manual of WNAP-7325/WNAP-7335

5.1.9 Access Control

Choose the operation mode you require, and then enter “Access Control” by clicking the Setup button next to it

and the following page will be displayed. This section allows you to configure the wireless access control

settings.

Figure 5-19 Access Control

Object Description

Wireless Access

You can choose “Disable”, “Allow Listed” or “Deny Listed”.

Control Mode

Mac Address The MAC address to be filtered.

Comment Enter a comment of this setting.

-46-

User Manual of WNAP-7325/WNAP-7335

5.1.10 WAN Port Settings

Click “Operation Mode”  “AP Router” or “Wireless ISP” and then enter the “WAN Port Settings” by clicking

the Setup button next to it. This section allows you to configure the internet connection settings.

 DHCP (Auto Config)

Choose “DHCP” and the router will automatically obtain IP addresses, subnet masks and gateway addresses

from your ISP.

Figure 5-20 WAN Port Settings – DHCP

 Static Mode (Fixed IP)

If your ISP offers you static IP Internet connection type, select “Static Mode" and then enter IP address, subnet

mask, primary DNS and secondary DNS information provided by your ISP in the corresponding fields.

Figure 5-21 WAN Port Settings – Static IP

Object Description

 IP Address

Assigned by

Enter the WAN IP address provided by your ISP. Enquire your ISP if you

are not clear.

-47-

Your ISP

User Manual of WNAP-7325/WNAP-7335

 IP Subnet Mask

 ISP Gateway IP

Address

 Primary DNS

Server

 Secondary DNS

Server

Enter WAN Subnet Mask provided by your ISP.

Enter the WAN Gateway address provided by your ISP.

Enter the necessary DNS address provided by your ISP. Default is

8.8.4.4.

Enter the other DNS address if your ISP provides you with 2 such

addresses. Default is 8.8.8.8.

 PPPOE (ADSL)

Select PPPOE if your ISP is using a PPPoE connection and provide you with PPPoE user name and password

info.

Figure 5-22 WAN Port Settings – PPPOE

Object Description

 User Name

Enter the User Name provided by your ISP.

 Password Enter the password provided by your ISP.

 Verify Password

Enter the password again to verify if it is correct.

-48-

User Manual of WNAP-7325/WNAP-7335

5.1.11 Dynamic DNS Settings

Click “Operation Mode”  “AP Router” or “Wireless ISP” and then enter the “Dynamic DNS Settings” by

clicking the Setup button next to it. This section allows you to configure the DDNS settings.

Object Description

 DDNS option

 Dynamic DNS Provider

 Account

 Password

 DDNS

Example of Planet DDNS Settings:

Figure 5-23 Dynamic DNS Settings

Disable: Disable DDNS function

Enable Easy DDNS: Enable PLANET Easy DDNS
Enable Dynamic DDNS: You are allowed to modify the DDNS

settings.

Select a server provider or disable the existing server.

Enter the DDNS user name of the DDNS account.

Enter the DDNS password of the DDNS account.

Enter the host name or domain name provided by DDNS
provider.

Please go to http://www.planetddns.com/

Please refer to the FAQ (http://www.planetddns.com/index.php/faq

to register a Planet DDNS account.

) for how to register a free account.

-49-

User Manual of WNAP-7325/WNAP-7335

Click “Operation Mode”  “AP Router” or “Wireless ISP”, select Dynamic DNS Settings and press “Setup”.

Step 1. Select “Enable Dynamic DDNS” and “PlanetDDNS.com” from the list of Dynamic DNS Provider to

use the Planet DDNS service.

Step 2. Configure the DDNS account that has been registered in Planet DDNS website.

Account: Enter your DDNS host (format: xxx.planetddns.com, xxx is the registered domain name)

Password: Enter the password of your account.

DDNS: Enter your DDNS host again.

-50-

User Manual of WNAP-7325/WNAP-7335

Step 3. Go to “Remote Management” to enable remote access from WAN port.

Step 4. Go to “WAN Port Settings” to configure WAN connection to Static Mode (fixed IP).

Step 5. Save the setting and connect your WAN port of the Wireless AP to the internet via Ethernet cable.

In a remote computer, enter the DDNS host name as the figure shown below. Then, you should be able to login

the WNAP-7325 remotely.

Example of Easy DDNS Settings:

This service is not required to register any DDNS account.

-51-

User Manual of WNAP-7325/WNAP-7335

Please refer to the procedure listed as follows to configure using Planet Easy DDNS service.

Step 1. Select “Enable Easy DDNS” to use the Planet Easy DDNS service.

Easy Domain Name: Display the specified domain name for this device. (Format: ptxxxxxx.planetddns.com,

xxxxxx is the last six-digit of the WAN Port MAC address)

Step 2. Go to “Remote Management” to enable remote access from WAN port.

Step 3. Go to “WAN Port Settings” to configure WAN connection to Static Mode (fixed IP).

-52-

User Manual of WNAP-7325/WNAP-7335

Step 6. Save the setting and connect your WAN port of the Wireless AP to the internet via Ethernet cable.

In a remote computer, enter the Easy Domain Name displayed in Step 1. Then, you should be able to login the

WNAP

-7325 remotely

.

5.1.12 Remote Management

Click “Operation Mode”  “AP Router” or “Wireless ISP” and then enter the “Remote Management” by

clicking the Setup button next to it. This section allows you to enable or disable the remote management through

the WAN port.

Figure 5-24 Remote Management

Object Description

 Remote management

Enable or Disable this function.

(via WAN)

 Ping from WAN

Enable or Disable this function.

-53-

User Manual of WNAP-7325/WNAP-7335

5.1.13 DHCP Server Settings

Click “Operation Mode”  “AP Router” or “Wireless ISP” and then enter the “DHCP Server Settings” by

clicking the Setup button next to it. This section allows you to configure the DHCP server.

Figure 5-25 DHCP Server Settings

Object Description

 DHCP Server

Select as DHCP server or disable the function.

Select the time for using one assigned IP from the dropdown

 Lease Time

list. After the lease time, the AP automatically assigns new IP
addresses to all connected computers.

 From

 To

The start IP address of all the available successive IPs.

The end IP address of all the available successive IPs.

5.1.14 DMZ Settings

Click “Operation Mode”  “AP Router” or “Wireless ISP” and then enter the “DMZ Settings” by clicking the

Setup button next to it. This section allows you to configure the DMZ server.

Figure 5-26 DMZ Settings

-54-

User Manual of WNAP-7325/WNAP-7335

Object Description

 DMZ Setting

 DMZ IP Address

Disable or Enable DMZ function.

Enter the DMZ IP address.

5.1.15 Virtual Server Settings

Click “Operation Mode”  “AP Router” or “Wireless ISP” and then enter the “Virtual Server Settings” by

clicking the Setup button next to it. This section allows you to configure the virtual server.

Figure 5-27 Virtual Server Settings

Object Description

 Virtual Server

 Protocol

 IP Address

 Port Range

 Comment

Enable or disable Virtual Server.

You can choose TCP, UDP or Both.

Enter the LAN IP.

Set the range of public port.

Set a name for the rule.

5.1.16 IP Filtering Settings

Click “Operation Mode”  “AP Router” or “Wireless ISP” and then enter the “IP Filtering Settings” by clicking

the Setup button next to it. This section allows you to configure the IP filtering settings.

-55-

User Manual of WNAP-7325/WNAP-7335

Figure 5-28 IP Filtering Settings

Object Description

 Filtering

 Protocol

 IP Address

 Comment

Enable or disable IP Filtering.

You can choose TCP, UDP or Both.

Enter the IP address to be filtered.

Set a name for the rule.

5.1.17 Port Filtering Settings

Click “Operation Mode”  “AP Router” or “Wireless ISP” and then enter the “Port Filtering Settings” by

clicking the Setup button next to it. This section allows you to configure the port filtering settings.

Figure 5-29 Port Filtering Settings

Object Description

 Filtering

 Protocol

 Port Range

 Comment

Enable or disable IP Filtering.

You can choose TCP, UDP or Both.

Enter the range of Port to be filtered.

Set a name for the rule.

-56-

User Manual of WNAP-7325/WNAP-7335

5.1.18 MAC Filtering Settings

Click “Operation Mode”  “AP Router” or “Wireless ISP” and then enter the “Mac Filtering Settings” by

clicking the Setup button next to it. This section allows you to configure the MAC filtering settings.

Figure 5-30 Mac Filtering Settings

Object Description

 Filtering

 Mac Address
 Comment

Enable or disable Mac Filtering.

Enter the Mac address to be filtered.
Set a name for the rule.

5.1.19 Bandwidth Control

Click “Operation Mode”  “AP Router” or “Wireless ISP” and then enter the “Bandwidth Control” by clicking

the Setup button next to it. This section allows you to configure the bandwidth control.

Figure 5-31 Bandwidth Control Settings

Object Description

 Quality of

Enable or disable the QoS service.

-57-

Service

User Manual of WNAP-7325/WNAP-7335

 Type

 Local IP Address

 MAC Address

Select QoS type IP Address or Mac Address.

The IP address segment which uses this QoS rule.

The Mac address which uses this QoS rule.

 Uplink BandWidth

Set the maximum uplink bandwidth allowed by the listed QoS rules.

(Kbps)

 Downlink

Set the maximum downlink bandwidth allowed by the listed QoS rules.

BandWidth (Kbps)

 Comment

Set a name for the rule.

5.1.20 SNMP

Click “Operation Mode”  “AP Router” or “Wireless ISP” and then enter the “SNMP” by clicking the Setup

button next to it. This section allows you to configure the SNMP.

Figure 5-32 SNMP Settings

Object Description

 SNMP

Enable or disable the SNMP service.

Enter a Read Community name for verification with the SNMP manager

 Read Community

for SNMP Read requests.

Enter a Write Community name for verification with the SNMP manager

 Write Community

for SNMP Write requests.

 Trap IP 1

Enter the Trap IP address.

Enter an SNMP Trap Community name for verification with the SNMP

 Trap Community

manager for SNMP Trap requests.

-58-

User Manual of WNAP-7325/WNAP-7335

5.2 System Configuration

On this page, you can configure the system of the AP, including IP settings, Time settings, Password settings,
System management, Ping Watchdog, Firmware upgrade, Configuration save and restore, Factory default,
Reboot and Schedule reboot.

Figure 5-33 System Configuration default page

5.2.1 Default IP Settings

Click “System Configuration”  “Device IP Settings” and the following page will be displayed.

Figure 5-34 Default IP Settings

-59-

The page includes the following fields:

Object Description

Access Point’s LAN IP.

User Manual of WNAP-7325/WNAP-7335

 IP Address

The default is 192.168.1.253. You can change it according to your

needs.

 IP Subnet Mask

 Gateway IP Address

 Primary DNS Server

 Secondary DNS Server

Access Point’s LAN subnet mask.

The Gateway IP address of Access Point.

Enter the DNS server. The default is 8.8.4.4.

Enter the DNS server. The default is 8.8.8.8.

5.2.2 Time Settings

Click “System Configuration”  “Time Settings” and the following page will be displayed.

Figure 5-35 Time Settings

Object Description

 Enable NTP

Enable it to support NTP (Network Time Protocol) for automatic time

and date setup.

 Server Name

 NTP Request Interval

Enter the host name or IP address of the time server if you wish.

Specify a frequency (in hours) for the access point to

update/synchronize with the NTP server.

 Local Time Zone

Select the time zone of your country/region. If your country/region is

not listed, please select another country/region whose time zone is

the same as yours.

 Local Date and Time

Set the access point’s date and time manually.

-60-

User Manual of WNAP-7325/WNAP-7335

5.2.3 Password Settings

Click “System Configuration”  “Password Settings” and the following page will be displayed.

Figure 5-36 Password Settings

Object Description

 Current Password

Set the access point’s administrator password. This is used to log in

to the browser based on the configuration interface.

 New Password

 Re-enter New

Enter a new password.

Enter the new password again.

Password

5.2.4 System Management

Click “System Configuration”  “System Management” and the following page will be displayed.

-61-

User Manual of WNAP-7325/WNAP-7335

Figure 5-37 System Management

Object Description

 Device Name

Enter a name for this access point. Default is WNAP-7325 or

WNAP-7335.

 POE Passthrough

 UPnP

Enable the POE Passthrough function.

※ When the option “Enable POE Passthrough” in the System

Management page is checked, the LAN2 can supply passive PoE

power to the second WNAP-7325 or WNAP-7335 through the LAN 2.

Check to enable the UPnP function.
The UPnP feature allows the devices, such as Internet computers,

to access the local host resources or devices as needed. UPnP

devices can be automatically discovered by the UPnP service

application on the LAN. This option is only available in AP

Router mode.

 Syslog

 IGMP

Check to enable Syslog function.

Check to enable the IGMP Proxy function.

This option is only available in AP Router mode.

5.2.5 Ping Watchdog

Click “System Configuration”  “Ping Watchdog” and the following page will be displayed.

-62-

User Manual of WNAP-7325/WNAP-7335

Figure 5-38 Ping Watchdog

Object Description

 Ping Watchdog

 IP Address 1

 Ping Frequency

 Failed tries

 Action

Enable or Disable this function.

Enter the IP address which pings every time interval

Set times from 10 to 999.

Select failed tries from 1 to 5.

System will reboot when failing to ping the IP.

5.2.6 Firmware Upgrade

Click “System Configuration”  “Firmware Upgrade” and the following page will be displayed.

Figure 5-39 Firmware Upgrade

-63-

Object Description

User Manual of WNAP-7325/WNAP-7335

 Browse

Click Browse to select the firmware file and click Upgrade to

upgrade the firmware.

5.2.7 Configuration Save and Restore

Click “System Configuration”  “Configuration Save and Restore” and the following page will be displayed.

Figure 5-40 Configuration Save and Restore

Object Description

 SAVE

 Browse

Click SAVE to save the configuration to a management host.

Click Browse to select the configuration file and click Restore to

restore the configuration file.

5.2.8 Factory Default

Click “System Configuration”  “Factory Default” and the following page will be displayed.

Press YES to restore to factory default.

Figure 5-41 Factory Default

-64-

User Manual of WNAP-7325/WNAP-7335

5.2.9 Reboot System

Click “System Configuration”  “Reboot System” and the following page will be displayed.

Press YES to reboot the system.

Figure 5-42 Reboot System

5.2.10 Schedule Reboot

Click “System Configuration”  “Schedule Reboot” and the following page will be displayed.

This page allows you to enable and configure system reboot schedule. The device can regularly reboot

according to the reserved time when connecting to the Internet.

Figure 5-43 Schedule Reboot

-65-

User Manual of WNAP-7325/WNAP-7335

Object Description

 Schedule Reboot

 Reboot Time

 Reboot Plane

 Weekday

Enable or Disable this function.

Enter the time that you want to reboot this device.

Select Weekday to reboot in the day you choose or Every day.

Select the day that you want to reboot.

1. This setting will only take effect when the Internet connection is accessible and the GMT
time is configured correctly.

2. You must select at least one day when choosing “Weekday” as your reboot plan.

3. When choosing “Every day” as your reboot plan, the “Weekday” will be grayed out
(disabled), which means Every day will auto reboot at the time that you schedule.

 Example of how to configure Schedule Reboot. Please take the following steps:

Before configuring schedule reboots, please ensure the Internet connection is accessible and the GMT time is

configured correctly according to NTP Settings page.

Step 1. Enable the “Schedule Reboot”.

Step 2. Enter the Reboot Time (24-hour format) to enable this function to take effect. For example, if you want

this function to work at 23:00 every Sunday, choose "Weekday" in the Reboot Plan field.

Figure 5-44 Schedule Reboot - Example

Step 3. Click the “Apply Changes” button to take this function effect.

-66-

User Manual of WNAP-7325/WNAP-7335

5.3 Tools

5.3.1 Network Ping

Click “Tools”  “Network Ping” and the following page will be displayed.

Ping is a network tool used to test whether a particular host is reachable across an IP network.

Enter the IP, Ping Count, and click “Ping” to diagnostic your internet connection.

Figure 5-45 Network Ping

5.3.2 Network Traceroute

Click “Tools”  “Network Traceroute” and the following page will be displayed.

Traceroute is a computer network diagnostic tool for displaying the route (path) and measuring transit delays of

packets across an Internet Protocol (IP) network. It can help identify connection problems.

Enter the IP

and click “T

raceroute” to diagnostic your internet connection.

-67-

User Manual of WNAP-7325/WNAP-7335

Figure 5-46 Network Traceroute

-68-

5.4 Device Status

User Manual of WNAP-7325/WNAP-7335

Figure 5-47 Device Status

-69-

User Manual of WNAP-7325/WNAP-7335

5.4.1 Device Information

Click “Device Status”  “Device Information” and the following page will be displayed.

The page includes the following fields:

Object Description

 Firmware Version

 Device IP

 Device MAC

 Gateway IP

 DNS IP

 Wireless MAC

 Uptime

 CPU Loading

Figure 5-48 Device Information

Displays current F/W version.

Displays IP of AP.

Displays AP’s LAN MAC address.

Displays Gateway IP of AP.

Displays DNS IP of AP.

Displays AP’s Wireless MAC address.

Displays the uptime of AP.

Displays the CPU loading of AP.

-70-

User Manual of WNAP-7325/WNAP-7335

5.4.2 Wireless Information

Click “Device Status”  “Wireless Information” and the following page will be displayed.

The page includes the following fields:

Object Description

 Operation Mode

 Physical address

 SSID

 Band

 Radio Channel

 Wireless Encryption

Figure 5-49 Wireless Information

Displays current Operation Mode.

Displays AP’s Wireless MAC address.

It is the wireless network name. The default SSID is

WNAP-7325 or WNAP-7335.

Displays operating channel width which is Auto Select, 5G

11NA HT20 or 5G 11NA HT40.

Displays the channel you would like to use. The channel range

will be changed by selecting a different domain.

Displays the encryption type that you would like to use.

 Transmit Power

Display the TX power that you would like to use.

-71-

User Manual of WNAP-7325/WNAP-7335

5.4.3 LAN Information

Click “Device Status”  “LAN Information” and the following page will be displayed.

The page includes the following fields:

Object Description

 Physical Address

 IP Address

 Network Mask

 Default Gateway

 DHCP Server

 DHCP Start IP Address

 DHCP Finish IP

Figure 5-50 LAN Information

Displays AP’s LAN MAC address.

Displays IP of AP.

Displays Network Mask of AP.

Displays Gateway IP of AP.

Enable or Disable DHCP server.

Enter the starting IP address for the DHCP server’s IP

assignment.

Enter the ending IP address for the DHCP server’s IP

Address

assignment.

-72-

User Manual of WNAP-7325/WNAP-7335

5.4.4 Wireless Client Table

Click “Device Status”  “Wireless Client Table” and the following page will be displayed.

Figure 5-51 Wireless Client Table

The page includes the following fields:

Object Description

 No.

 Mac Address

 Connection Speed

 Signal Strength

Displays the number of connecting device.

Displays Mac address of AP.

Displays connection speed of device.

Display signal strength of device.

The signal strength between “-30 and -70” can set up a reliable

connection.

-73-

User Manual of WNAP-7325/WNAP-7335

5.4.5 System Log

Choose menu “Device Status  “System Log” to view the logs of the Wireless AP.

5.5 Logout

Select “Logout” to logout the system.

Figure 5-52 System Log

Figure 5-53 Logout

-74-

User Manual of WNAP-7325/WNAP-7335

Figure 5-54 Re-login

-75-

User Manual of WNAP-7325/WNAP-7335

Appendix A: Troubleshooting

If you found the AP is working improperly or stop responding to you, please read this troubleshooting first before

contacting the Planet Tech Support for help. Some problems can be solved by yourself within very short time.

Scenario Solution

The AP is not responding to me when

I want to access it by web browser.

I can’t get connected to the Internet.

I can’t locate my AP by my wireless

a. Please check the connection of the power cord and the

Ethernet cable of this AP. All cords and cables should be
correctly and firmly inserted to the AP.

b. If all LEDs on this AP are off, please check the status of

power adapter, and make sure it is correctly powered.
c. You must use the same IP address section that AP uses.
d. Are you using MAC or IP address filter? Try to connect

the AP by another computer and see if it works; if not,

please reset the AP to the factory default settings (Press

the ‘reset’ button for over 10 seconds).
e. Set your computer to static IP address, and see if the

Planet Smart Discovery can find the AP or not.
f. If you did a firmware upgrade and this happens, contact

the Planet Tech Support for help.
g. If all the solutions above don’t work, contact the Planet

Tech Support for help.
a. Check the Internet connection status from the router that

is connected with the AP.
b. Please be patient. Sometimes, Internet is just that slow.
c. If you have connected a computer to Internet directly

before, try to do that again, and check if you can get

connected to Internet with your computer directly

attached to the device provided by your Internet service

provider.
d. Check PPPoE / L2TP / PPTP user ID and password in

your router again.
e. Call your Internet service provider and check if there’s

something wrong with their service.
f. If you just can’t connect to one or more website, but you

can still use other internet services, please check

URL/Keyword filter.
g. Try to reset the AP and try again later.
h. Reset the device provided by your Internet service

provider.
i. Try to use IP address instead of hostname. If you can

use IP address to communicate with a remote server,

but can’t use hostname, please check DNS setting.
a. ‘Broadcast ESSID’ set to off?

-76-

User Manual of WNAP-7325/WNAP-7335

device.

File downloading is very slow or

breaks frequently.

I can’t log into the web management

interface; The password is wrong.

The AP becomes hot

b. The antenna is properly secured.
c. Are you too far from your AP? Try to get closer.
d. Please remember that you have to input ESSID on your

wireless client manually, if ESSID broadcast is disabled.
a. Are you using QoS function? Try to disable it and try

again.
b. Internet is slow sometimes; try to be patient.
c. Try to reset the AP and see if it’s better after that.
d. Try to know what computers do on your local network. If

someone’s transferring big files, other people will think

Internet is really slow.
e. If this never happens before, call you Internet service

provider to know if there is something wrong with their

network.
a. Make sure you’re connecting to the correct IP address of

the AP.
b. Password is case-sensitive. Make sure the ‘Caps Lock’

light is not illuminated.
c. If you really forget the password, do a hardware reset.
a. This is not a malfunction, if you can keep your hand on

the AP’s case.
b. If you smell something wrong or see the smoke coming

out from AP or A/C power adapter, please disconnect

the AP and A/C power adapter from utility power (make

sure it’s safe before you’re doing this!), and call your

dealer for help.

-77-

User Manual of WNAP-7325/WNAP-7335

Appendix B: Use Planet Smart Discovery to find AP

To easily discover the WNAP-7325 in your Ethernet environment, the Planet Smart Discovery Utility from user’s

manual CD-ROM is an ideal solution.

The following install instructions will guide you to running the Planet Smart Discovery Utility.

Step 1: Deposit the Planet Smart Discovery Utility in administrator PC.

Step 2: Execute this utility.

Step 3: Click the “Refresh” button as shown below to update the list of the currently connected devices.

Figure C-1

Step 3: Select the WNAP-7325 from the list and then click the “Connect to Device” button to login to the Web

Management Configuration Page.

The fields in white background can be modified directly, and then you can apply the new
setting by clicking the “Update Device” button.

-78-

User Manual of WNAP-7325/WNAP-7335

Q1: How to set up the AP Client Connection

Topology:

Appendix C: FAQ

1. Use static IP in the PCs that are connected with AP-1(Site-1) and AP-2(Site-2). In this case, Site-1 is

Step

“192.168.1.100”, and Site-2 is “192.168.1.200”.

-79-

User Manual of WNAP-7325/WNAP-7335

Step 2. In AP-1, go to “Operation Mode” to configure it to Access Point Mode.

※ You can also configure it in “AP Router” mode if you want to connect the WAN port of the AP

to the internet directly.

Step 3. Click “Setup” to configure the following parameters and then click Save & Restart to save the settings.

1)

Network ID (SSID): set to a unique value

2) Channel: set to a fixed one

3)

Security Setting: strongly suggested to configure it.

In this case, we configure it to WPA2-PSK, AES

-80-

User Manual of WNAP-7325/WNAP-7335

-81-

User Manual of WNAP-7325/WNAP-7335

Step 4. In AP-2, modify the default IP to the same IP range but different from AP-1.

In this case, the IP is changed to 192.168.1.252.

Step 5. In AP-2, configure it in “Client” mode and click “Setup”.

-82-

User Manual of WNAP-7325/WNAP-7335

Step 6. Click “Setup” and then click Site Survey to find the AP-1.

Step 7. Select the AP-1 from the list.

-83-

User Manual of WNAP-7325/WNAP-7335

Step 8. Click “SET SECURITY” to configure the Pre-Shared Key and then click “Save” to close the window.

Step 9. Click “OK” and “Save & Restart” to apply the setting.

-84-

User Manual of WNAP-7325/WNAP-7335

Step 10. In AP-1, go to “Device Status-> Wireless Client Table” to check whether AP-2 should be in the list.

Step 11. Use command line tool to ping each other to ensure the link is successfully established.

From Site-1, ping 192.168.1.200; and in Site-2, ping 192.168.1.100.

Step 12. Configure the TCP/IP settings of Site-2 to “Obtain an IP address automatically”.

-85-

User Manual of WNAP-7325/WNAP-7335

Step 13. Use command line tool to ping the DNS (e.g., Google) to ensure Site-2 can access internet through the

wireless connection.

The attention of the following hints should be paid:

1) The encryption method must be the same as that of both sites if configured.

2) Both sites should be Line-of-Sight.

3) For the short distance connection less than 1km, please reduce the "Transmit power" of both
sites.

4) For the long distance connection over 1km, please adjust the "Transmit Distance" to the actual

distance or double of the actual distance.

-86-

User Manual of WNAP-7325/WNAP-7335

Q2: How to set up the WDS Connection

Topology:

Step

1. Use static IP in the PCs that are connected with WNAP-7350-1 (Site-1) and WNAP-7350-2 (Site-2). In

this case, Site-1 is “192.168.1.100”, and Site-2 is “192.168.1.200”.

-87-

User Manual of WNAP-7325/WNAP-7335

Step 2. In AP-1, go to “Operation Mode” to configure it in Access Point Mode.

Step 3. Click “Setup” to configure the following parameters and then click Save & Restart to save the settings.

4)

Network ID (SSID): set to a unique value

5) Channel: set to a fixed one

6)

Security Setting: strongly suggested to configure it.

In this case, we configure it to WPA2-PSK, AES

-88-

User Manual of WNAP-7325/WNAP-7335

Step 4. In AP-2, modify the default IP to the same IP range but different from AP-1.

In this case, the IP is changed to 192.168.1.252.

Step 5. In AP-2, configure it in “Client” mode and click “Setup”.

-89-

Step 6. Click “Setup” and then click Site Survey to find AP-1.

User Manual of WNAP-7325/WNAP-7335

Step 7. Select AP-1 from the list.

-90-

User Manual of WNAP-7325/WNAP-7335

Step 8. Click “SET SECURITY” to configure the Pre-Shared Key and then click “Save” to close the window.

Step 9. Click “OK” and click “Save & Restart” to apply the setting.

Step 10. In AP-1, go to “Device Status-> Wireless Client Table” to check whether AP-2 should be in the list.

Step 11. Use command line tool to ping each other to ensure the link is successfully established.

From Site-1, ping 192.168.1.200; and in Site-2, ping 192.168.1.100.

-91-

User Manual of WNAP-7325/WNAP-7335

The attention of the following hints should be paid:

1) The encryption method must be the same as that of both sites if configured.

2) Both sites should be Line-of-Sight.

3) For the short distance connection less than 1km, please reduce the "Transmit power" of both
sites.

4) For the long distance connection over 1km, please adjust the "Transmit Distance" to the actual
distance or double of the actual distance.

-92-

EC Declaration of Conformity

For the following equipment:

*Type of Product
*Model Number : WNAP-7325 / WNAP-7335

* Produced by:
Manufacturer’s Name : Planet Technology Corp.
Manufacturer’s Address: 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.)

is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to
Directive 2006/95/EC
For the evaluation regarding the R&TTE the following standards were applied:

Responsible for marking this declarati o n i f the:

: 5GHz 802.11a/n 300Mbps Wireless LAN Outdoor CPE

1999/5/EC R&TTE, Low Voltage

.

EN 301 893 V1.7.1 (2011-06)
EN 301 489-1 V1.9.2 (2011)

EN 301 489-17 V2.2.1 (2012)
EN 62311 (2008)
EN 60950-1 (2006 + A11: 2009 + A1:2010 +

A12:2011+A2:2013)

 Manufacturer  Authorized representative established within the EU

Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Tai pei Ci t y 23 1, Taiw an
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Product Manager

(R.O.C.)

Taiwan

8th Jan., 2015

Place Date Legal Signature

PLANET TECHNOLOGY CORPORATION

e-mail: [e-mail] http://www.planet.com.tw

10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:[phone] Fax:[phone]

EC Declaration of Conformity

English

Česky

Dansk

Deutsch

Eestikeeles

Ελληνικά

Español

Français

Italiano

Latviski

Hereby, PLANET Technology Corporation,
declares that this 300Mbps 802.11a/n Wireless
Outdoor CPE is in compliance with the essential
requirements and other relevant provisions of
Directive 1999/5/EC.

Společnost PLANET Technology Corporation,
tímto prohlašuje, že tato 300Mbps 802.11a/n
Wireless Outdoor CPE splňuje základní
požadavky a další příslušná ustanovení směrnice
1999/5/EC.

PLANET Technology Corporation, erklærer
herved, at følgende udstyr 300Mbps 802.11a/n
Wireless Outdoor CPE overholder de væsentlige
krav og øvrige relevante krav i direktiv 1999/5/EF

Hiermit erklärt PLANET Technology Corporation,
dass sich dieses Gerät 300Mbps 802.11a/n
Wireless Outdoor CPE in Übereinstimmung mit
den grundlegenden Anforderungen und den
anderen relevanten

Vorschriften der Richtlinie 1999/5/EG befindet".
(BMWi)

Käesolevaga kinnitab PLANET Technology

Corporation, et see 300Mbps 802.11a/n Wireless

Outdoor CPE vastab Euroopa Nõukogu direktiivi

1999/5/EC põhinõuetele ja muudele olulistele
tingimustele.

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ , PLANET Technology
Corporation, ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤ Ο 300Mbps

802.11a/n Wireless Outdoor
CPEΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥ ΣΙΩ ΔΕΙ Σ

ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙ ΠΕΣ

ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ

Por medio de la presente, PLANET Technology
Corporation, declara que 300Mbps 802.11a/n
Wireless Outdoor CPE cumple con los requisitos

esenciales y cualesquiera otras disposiciones
aplicables o exigibles de

la Directiva 1999/5/CE

Par la présente, PLANET Technology

Corporation, déclare que les appareils du
300Mbps 802.11a/n Wireless Outdoor CPE sont

conformes aux exigences essentielles et aux
autres dispositions pertinentes de la directive
1999/5/CE

Con la presente , PLANET Technology

Corporation, dichiara che questo 300Mbps

802.11a/n Wireless Outdoor CPE è conforme ai

requisiti essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva

1999/5/CE.

Ar šo PLANET Technology Corporation,
apliecina, ka šī 300Mbps 802.11a/n Wireless
Outdoor CPE atbilst Direktīvas 1999/5/EK
pamatprasībām un citiem atbilstošiem
noteikumiem.

Lietuviškai

Magyar

Malti

Nederlands

Polski

Português

Slovensky

Slovensko

Suomi

Svenska

Šiuo PLANET Technology Corporation,, skelbia,
kad 300Mbps 802.11a/n Wireless Outdoor CPE
tenkina visus svarbiausius 1999/5/EC direktyvos
reikalavimus ir kitas svarbias nuostatas.

A gyártó PLANET Technology Corporation, kijelenti,
hogy ez a 300Mbps 802.11a/n Wireless Outdoor
CPE megfelel az 1999/5/EK irányelv
alapkövetelményeinek és a kapcsolódó
rendelkezéseknek.

Hawnhekk, PLANET Technology Corporation,
jiddikjara li dan 300Mbps 802.11a/n Wireless
Outdoor CPE jikkonforma mal-ħtiġijiet essenzjali u
ma provvedimenti oħrajn relevanti li hemm
fid-Dirrettiva 1999/5/EC

Hierbij verklaart , PLANET Technology orporation,
dat 300Mbps 802.11a/n Wireless Outdoor CPE in
overeenstemming is met de essentiële eisen en de
andere relevante bepalingen van richtlijn 1999/5/EG

Niniejszym firma PLANET Technology Corporation,
oświadcza, że 300Mbps 802.11a/n Wireless
Outdoor CPE spełnia wszystkie istotne wymogi i
klauzule zawarte w dokumencie „Directive
1999/5/EC”.

PLANET Technology Corporation, declara que este
300Mbps 802.11a/n Wireless Outdoor CPE está

conforme com os requisitos essenciais e outras
disposições da Directiva 1999/5/CE.

Výrobca PLANET Technology Corporation, týmto
deklaruje, že táto 300Mbps 802.11a/n Wireless
Outdoor CPE je v súlade so základnými
požiadavkami a ďalšími relevantnými predpismi
smernice 1999/5/EC.

PLANET Technology Corporation, s tem potrjuje,
da je ta 300Mbps 802.11a/n Wireless Outdoor CPE
skladen/a z osnovnimi zahtevami in ustreznimi določili
Direktive 1999/5/EC.

PLANET Technology Corporation, vakuuttaa täten
että 300Mbps 802.11a/n Wireless Outdoor CPE
tyyppinen laite on direktiivin 1999/5/EY oleellisten
vaatimusten ja sitä koskevien direktiivin muiden
ehtojen mukainen.

Härmed intygar, PLANET Technology Corporation,
att denna 300Mbps 802.11a/n Wireless Outdoor
CPE står i överensstämmelse med de väsentliga
egenskapskrav och övriga relevanta bestämmelser
som framgår av direktiv 1999/5/EG.